Manual Central Panel MIP B77 IDC. Date:/8/ Rev.:.0
Manual Central Panel MIP B77 IDC Index: MANUAL CENTRAL PANEL MIP B77 IDC... INDEX:... INTRODUCTION:... BKI TECHNOLOGY:... WIRING DIAGRAM:... CONNECTOR'S DESCRIPTION:... Connection of Auto Brake and Flaps indicators to central panel:... INPUTS AND OUTPUTS DECLARATION:... 5 LINKS DE INTERÉS:... ERROR! MARCADOR NO DEFINIDO. ANEXE:... 6 www.opencockpits.com
Manual Central Panel MIP B77 IDC Introduction: B77 MIP central panel, flaps 5º, with IDC connection and with integrated backlight technology BKI panel. Made from a 6mm thick piece, with painted finish and professional engraving. This panel was desigend to connect with inputs and outputs cards like IOCARD MIP, Master plus Expansion or other. The panel has the following operating elements: Rotary switches and encoders and momentary switch. MFD keys. Autobrake indicator. Backlight. As a novelty we introduce two concentric rotary encoders switches for full functionality of the panel and outputs (5V) for external panel indicators (Anti Skid Inop, LE Flaps Transit and LE Flaps Extended). BKI Technology: The BKI technology is similar to the original used in the original Boeing panels, it is embedded within the backlight panels, increasing the quality of the backlight and a significant drop in energy consumption and to avoid light pollution around the panels. Wiring diagram: Central panel can be connected to any inputs and outputs card through 0 pins IDC connector. SEE ANEXE. Connector's Description: The central panel put into service with the following connections. J9 CONNECTOR 0 PINS I/O PIN FUNCTION I/O PIN FUNCTION GND GND OUTPUTS I SPD REF ROTARY "<" O INDICATOR (5V INCLUDED) I5 SPD REF ROTARY "SET" O INDICATOR (5V) I6 SPD ENCODER O INDICATOR (5V) I7 SPD ENCODER BIS O 5 INDICATOR (5V) GNDG 5 GND INPUTS I9-7 - 6 - I8 6 AUTOBRAKE ROTARY "RTO" I 7 N SET ROTARY "" I9 7 AUTOBRAKE ROTARY "OFF" I 8 N SET ROTARY "" I0 8 AUTOBRAKE ROTARY "" I 9 N SET ROTARY "AUTO" I 9 AUTOBRAKE ROTARY "" I 0 N SET ROTARY "BOTH" I 0 AUTOBRAKE ROTARY "" I5 N SET ENCODER I AUTOBRAKE ROTARY "MAX" I6 N SET ENCODER BIS I MFD BUTTON "ENG" I7 FUEL FLOW "USED" I5 MFD BUTTON "SYS" I8 FUEL FLOW "RESET" GNDP GND BACKLIGHT www.opencockpits.com
GNDG 5 GND INPUTS I-8 PWLED 5 I9 6 - GNDP 6 I0 7 SPD REF ROTARY "AUTO" PWLED 7 Manual Central Panel MIP B77 IDC POSITIVE BACKLIGHT. Power feeding from. volts to.9 volts Attention: more voltage may damage the backlight! GND BACKLIGHT MFD BUTTONS POSITIVE BACKLIGHT MFD BUTTONS Power feeding from. volts to.9 volts. I 8 SPD REF ROTARY "V" - 8 - I 9 SPD REF ROTARY "VR" GNDG 9 GND INPUTS I8-I5 I 0 SPD REF ROTARY "WT" - 0 - J & J5 CONNECTORS: OUTPUTS INDICATORS PANEL (pcb connectors) I/O PIN FUNCTION I/O PIN FUNCTION POSITIVE O (5V USED) POSITIVE O (5V) J POSITIVE O (5V) J5 GND OUTPUTS POSITIVE O (5V) GND OUTPUTS (USED) USB Dimcontrol card is recommended to manage the backlight. Connection of Auto Brake and Flaps indicators to central panel: The Auto Brake Disarm indicator comes wired and operative from factory, but other indicators can be connected to the central panel (Anti Skid Inop, LE Flaps Transit and LE Flaps Extended). They can be connected to any inputs or outputs card directly or wired to the Central Panel. There are two ways.. The positive pins (pin ) of each indicator goes to their respective panel outputs (O, O, O & O): J pin (O) wired to Auto Brake Disarm pin, J pin (O) to Anti Skid Inop pin, J pin (O) to LE Flaps Transit pin and J5 pin (O) to LE Flaps Ext pin and negative pins (GNDs): from J5 pin to Auto Brake Disarm pin, from Auto Brake Disarm pin exits a jumper to Anti Skid Inop pin (GND), from Anti Skid Inop pin (GND) exits other jumper to LE Flaps Transit pin (GND) and from LE Flaps Transit pin exits other jumper to LE Flaps Ext pin. J5 O GND GND J O O O LE FLAPS EXT LE FLAPS TRANSIT ANTI SKID INOP AUTO BRAKE DISARM www.opencockpits.com
Manual Central Panel MIP B77 IDC. The positives are connected the same way: The positive pins (pin ) of each indicator goes to their respective panel outputs (O, O, O & O): J pin (O) wired to Auto Brake Disarm pin, J pin (O) to Anti Skid Inop pin, J pin (O) to LE Flaps Transit pin and J5 pin (O) to LE Flaps Ext pin and negative for Auto Brake Disarm indicator like factory wiring and for other indicators: from J5 pin (GND) exits a wire to Anti Skid Inop pin (GND), from Anti Skid Inop pin (GND) exits other jumper to LE Flaps Transit pin (GND) and from LE Flaps Transit pin exits other jumper to LE Flaps Ext pin. J5 O GND GND J O O O LE FLAPS EXT LE FLAPS TRANSIT ANTI SKID INOP AUTO BRAKE DISARM Inputs and Outputs Declaration: To declare variables of inputs and outputs the previous table of connection must be used. The numbers assigned will depend of wiring and inputs and outputs cards used. If we use a Master Expansion card with or without the IOCard MIP PCB the inputs and outputs are static, but other cards can be used too. With the IOCard MIP PCB and Master Expansion cards the inputs and outputs will be the same and the official OC scripts and custom scripts will be the same too. Inputs and outputs definition: // OUTPUTS Var 000, name MIPBRAKEDIS_O, Link IOCARD_OUT, DEVICE XX, Output // AUTO BRAKE DISARM INDICATOR Var 00, name MIPANTI_SKID_O, Link IOCARD_OUT, DEVICE XX, Output // ANTI SKID INOP INDICATOR Var 00, name MIPFLAPTRANS_O, Link IOCARD_OUT, DEVICE XX, Output // LE FLAPS TRANSIT INDICATOR Var 006, name MIPFLAPSEXT_O, Link IOCARD_OUT, DEVICE XX, Output // LE FLAPS EXTENDED INDICATOR // INPUTS // N SET Var 00, name NSET_I, Link IOCARD_SW, DEVICE XX, Input 6 // N SET ROTARY SWITCH POSITION Var 0, name NSET_I, Link IOCARD_SW, DEVICE XX, Input 7 // N SET ROTARY SWITCH POSITION Var 0, name NSETAUTO_I, Link IOCARD_SW, DEVICE XX, Input 8 // N SET ROTARY SWITCH POSITION AUTO Var 06, name NSETBOTH_I, Link IOCARD_SW, DEVICE XX, Input 9 // N SET ROTARY SWITCH POSITION BOTH Var 08, name NSETENC_I, Link IOCARD_SW, DEVICE XX, Input 0 // N SET ENCODER INPUT www.opencockpits.com 5
Manual Central Panel MIP B77 IDC // FUEL FLOW Var 00, name FUEL_USED_I, Link IOCARD_SW, DEVICE XX, Input // FUEL FLOW SWITCH USED Var 0, name FUEL_RESET_I, Link IOCARD_SW, DEVICE XX, Input // FUEL FLOW SWITCH RESET // SPD REF Var 0, name SPD_AUTO_I, Link IOCARD_SW, DEVICE XX, Input 5 // SPD REF ROTARY SWITCH POSITION AUTO Var 06, name SPD_V_I, Link IOCARD_SW, DEVICE XX, Input 6 // SPD REF ROTARY SWITCH POSITION V Var 08, name SPD_VR_I, Link IOCARD_SW, DEVICE XX, Input 7 // SPD REF ROTARY SWITCH POSITION VR Var 00, name SPD_WT_I, Link IOCARD_SW, DEVICE XX, Input 8 // SPD REF ROTARY SWITCH POSITION WT Var 0, name SPD_VREF_I, Link IOCARD_SW, DEVICE XX, Input 9 // SPD REF ROTARY SWITCH POSITION VREF Var 0, name SPD_A_I, Link IOCARD_SW, DEVICE XX, Input 50 // SPD REF ROTARY SWITCH POSITION TRIANGLE Var 06, name SPD_SET_I, Link IOCARD_SW, DEVICE XX, Input 5 // SPD REF ROTARY SWITCH POSITION SET Var 08, name SPD_ENC_I, Link IOCARD_SW, DEVICE XX, Input 5 // SPD REF ENCODER INPUT // AUTO BRAKE Var 00, name BRAKE_RTO_I, Link IOCARD_SW, DEVICE XX, Input 5 // AUTO BRAKE ROTARY SWITCH POSITION RTO Var 0, name BRAKE_OFF_I, Link IOCARD_SW, DEVICE XX, Input 55 // AUTO BRAKE ROTARY SWITCH POSITION OFF Var 0, name BRAKE I, Link IOCARD_SW, DEVICE XX, Input 56 // AUTO BRAKE ROTARY SWITCH POSITION Var 06, name BRAKE I, Link IOCARD_SW, DEVICE XX, Input 57 // AUTO BRAKE ROTARY SWITCH POSITION Var 08, name BRAKE I, Link IOCARD_SW, DEVICE XX, Input 58 // AUTO BRAKE ROTARY SWITCH POSITION Var 050, name BRAKE_MAX_I, Link IOCARD_SW, DEVICE XX, Input 59 // AUTO BRAKE ROTARY SWITCH POSITION MAX // MFD Var 05, name MFD_ENG_I, Link IOCARD_SW, DEVICE XX, Input 60 // MFD ENG MOMENTARY SWITCH BUTTON Var 05, name MFD_SYS_I, Link IOCARD_SW, DEVICE XX, Input 6 // MFD SYS MOMENTARY SWITCH BUTTON // FLAPS SERVO Var 056, name SERVO_FLAPL, Link USB_SERVOS, Device YY, Output, PosL 50, PosC 5, PosR 0, Type // LEFT NEEDLE SERVO OF FLAPS GAUGE. Var 058, name SERVO_FLAPR, Link USB_SERVOS, Device YY, Output, PosL 50, PosC 5, PosR 0, Type // RIGHT NEEDLE SERVO OF FLAPS GAUGE. With this purpose we end this manual and you are kindly invited to read the other Opencockpits items and the SIOC software manuals. Thank you for trusting us. www.opencockpits.com 6
Manual Central Panel MIP B77 IDC Links of interest: Support zone for customers: http://www.opencockpits.com/catalog/info/ www.opencockpits.com 7
Manual Central Panel MIP B77 IDC Anexe: 5 5 7 9 J8 CONA J6 CON J9 5 6 7 8 9 0 5 6 7 8 9 0 5 6 7 8 9 0 5 6 7 8 9 0 CON0 J 6 8 0 6 CON6A P SW CON J CON6A P J 5 6 7 CON7 LD LE D 5 7 9 5 6 8 0 6 I5 J CON J5 CON LD LED LD LED LD LED LD5 LED GN DG I I GN DG I I I5 I6 I7 GN DG I8 GN DG I0 I I GN DG I9 I I I5 I6 I7 PWLED GNDG GN DP I GNDG I8 I9 I0 I I I O O O O GN D GN D O O O O I I I I I5 I6 I7 I8 GN DG I9 I0 I I I I I5 I6 I7 GN DG I8 I9 I0 I I I I I5 GN DP PWLED GN DP PWLED GN DG GN DP PWLED www.opencockpits.com 8