Quick Guide XCAL-Harmony v2

Quick Guide XCAL-Harmony v2 2015 Dec

Contents 1. Installation of XCAL-Harmony v2 2. Syncing XCAL-Harmony and XCAL-Mobile/Solo 3. Main Menu 3-1. Configuration 3-2. Monitoring 3-3. Inbuilding 3-4. Map 3-5. Scanner 3-6. Logdata 3-7. Settings

1. Installation of XCAL-Harmony v2 1. Connect PC and Tablet by using cable. 2. In PC, create a new folder in tablet, and add XCAL-Harmony (*.apk) file in it. 3. In tablet, run ES file explorer. (ES File Explorer can be downloaded from Play Store.) 4. Execute XCAL-Harmony (*.apk) file. 5. When installation is successfully completed, XCAL-Harmony icon appears in application menu. 6. Run XCAL-Harmony application, and main screen appears as above. 3

2. Syncing XCAL-Harmony and XCAL-Mobile/Solo 1. Run XCAL-Mobile. 2. Select [M/S] from HW Menu. 3. Tap to select [Messenger (Harmony v2)]. 4. Messenger Mode is activated and started. 4

2. Syncing XCAL-Harmony and XCAL-Mobile/Solo 5. [Bluetooth Search]: Allows Bluetooth search at the initial connection with XCAL-Harmony. Tap [Yes] to allow. From the second-time connection to XCAL-Harmony, no need of allow BT search. 5

3. Main Menu Main screen of XCAL-Harmony v2 appearing when executing XCAL-Harmony application. 6

3. Main Menu Menu selection by swiping left and right and clicking menu buttons. 1. Menu bar at the top of main screen is displayed in all screens of XCAL-Harmony always moving to other menus directly by clicking desired menu buttons. 2. Swipe screen left and right to change menus. 7

3-1. Configuration 1. Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 1) When there is no searched paired devices in Bluetooth search list. 1 1) Tap a port number to connect XCAL-Solo/Mobile. 2) Tap [Scan] button when there is no mobile to connect in Paired Device List. 2 8

3-1. Configuration 1. (Cont d) Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 1) When there is no searched paired devices in Bluetooth search list. 3 In XCAL-Mobile/Solo application, make sure XCAL-Mobile/Solo information. 4 4) When no device is searched in Bluetooth scan list, check if Bluetooth search permission is configured to On in XCAL- Mobile/Solo application. 9

3-1. Configuration 1. Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 2) When there exists searched paired devices in Bluetooth search list. 1 1) Tap a port number to connect XCAL-Solo/Mobile. 2 Port number of the latest AutoCall is displayed. 2) Paired Devices list 에원하는모바일이없는경우 을선택합니다. 2) XCAL-Mobile/Solo, which have ever been connected to XCAL-Harmony before, are listed up. * If XCAL-Mobile/Solo is connected to the lastly connected port of XCAL-Harmony, the lately tested AutoCall scenario is assigned automatically. 10

3-1. Configuration 1. Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 3) Syncing XCAL-Mobile/Solo via Bluetooth. 5 5) Selected XCAL-Mobile/Solo is connected to port 1 as configured successfully. * Configure the other ports to sync XCAL-Mobile/Solo via Bluetooth. 11

3-1. Configuration 1. Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 3) Syncing XCAL-Mobile/Solo via Bluetooth for all XCAL-Harmony ports. 12

3-1. Configuration 1. Syncing XCAL-Mobile/Solo XCAL-Harmony syncs to XCAL-Mobile/Solo via Bluetooth. 4) Disconnecting the synced XCAL-Mobile/Solo from XCAL-Harmony. Tap Tap port# to disconnect XCAL-Mobile/Solo, and tap [OK] button to confirm. 13

3-1. Configuration 2. AutoCall Scenario - In main Configuration menu screen. 1 1) Tap [NEW], [EDIT], and [DEL] icons to create, edit, and delete call scenarios. * : Creates a new call scenario. * : Edits existing call scenarios. * : Deletes the selected call scenario. 2 2) Created AutoCall scenarios are listed and managed by call types. * Tapping a call type and corresponding call scenarios are listed. * If there is no created call scenario, call type button is shown in gray. * If there exists created call scenarios, call type button is shown in green. 3 3) Detailed information of selected call scenario is displayed. * I : Idle time/ S : Setup time/ T.S : Traffic.Setup time/ T : Traffic time 14

3-1. Configuration 2. AutoCall Scenario Scenario Setup screen. [Scenario Setup] screen creates, edits, and deletes call scenarios. [Scenario Setup] screen appears when tapping [NEW] button. 15

3-1. Configuration 2. AutoCall Scenario By tapping each scenario assignment button for respective ports, call scenarios are assigned. 5 Tap 5) Tap a scenario assignment button of a port# to assign a call scenario. 4 4) Tap to select a call scenario of each call type. 16

3-1. Configuration 2. AutoCall Scenario By tapping each scenario assignment button for respective ports, call scenarios are assigned. 17

3-2. Monitoring 1. Call Status Monitoring status of mobile and AutoCall test 18

3-2. Monitoring 1. Call Status DM * Status 상태 of 색상 DM 표시 Port : : Connected : : Disconnected : : Connecting * Mobile number + MIN Number_Current network * Background color shows status of current network of mobile. : LTE : WCDMA : GSM : CDMA : TD-SCDMA : Wi-Fi : Unknown * Status of GPS : Lock : Unlock : Disable - Idle/Setup/T.setup/Traffic + Progress - Progress = (Current Time/Time configured in scenario) * 100 -If Total Time is set, remained total time is displayed. * Progress colors for each time section : Idle : Setup/T.setup : Traffic *Total = number of calls / number of call scenarios *Success = number of success call (Success count/total call)*100 *Fail = number of all calls excepting success calls (BQ+CBQ+Connection+Setup+Traffic+Timeout+Drop+Incomplete+Pending) 19

3-2. Monitoring 1. Call Status 1) Detail View 1 Tap 1) Tap a call status section, Detail View screen appears (see next page). 20

3-2. Monitoring 1. Call Status 1) (Cont d) Detail View 2 Search call results by filtering scenario name or call result type. Turn On/Off Wi-Fi of corresponding mobile. 21

3-2. Monitoring 2. RF Summary 1) Filter Setting 1 Tap 1) Tap filter setting buttons. 22

3-2. Monitoring 2. RF Summary 1) (Cont d) Filter Setting 2 2) Select a network to monitor. * If [Current] is configured, RF parameter is displayed according to current network of mobile. 3 3) RF parameter can be monitored after filtered. 23

3-2. Monitoring 3. Signal Graph 1) Setting 24

3-2. Monitoring 3. Signal Graph 1) Setting 1 Tap 1) Tap G1 or G2 button of parameter. 25

3-2. Monitoring 4. Cell Measurement : Monitors cell measurement result of connected XCAL-Mobile/Solo. 26

3-2. Monitoring 5. Signaling MSG : Displays Signaling Message + SIP Message + Call Event 27

3-2. Monitoring 5. Signaling MSG 1) Signaling Message Filter Setting appearing by tapping [Filter] button 28

3-2. Monitoring 6. User Defined : Organizes screen by selecting menus of Call Status, RF Summary, Signal Graph, Cell Measurement, Signal MSG of M1 ~ M6. 1 Tap 29

3-2. Monitoring 6. User Defined 1) User Defined Settings 2 Select M1 ~ M6 to be displayed in the first Screen. Select a monitoring menus of Call Status, RF Summary, Signal Graph, Cell Measurement, Signaling MSG to be displayed in the first screen. 30

3-3. Inbuilding 1. Setting Lists up test building information. Building information is saved and re-used for next in-building tests. *.ibwc file can be imported. See next pages. Configures in-building information. Configures in-building floor information. Starts in-building test. 31

3-3. Inbuilding 1. Setting 1) Building Setting [GET GPS] button: Configures building location information automatically taking Google Address data. Enter a building name. Enter building address manually if GET GPS button does not work. Configure building floor to conduct test. Floor setting screen pops up. See next page. Configures test type in Measure pop-up screen; Moving, Fixed, TAB+JPG, Real Time Mapping. Saves or deletes building information. - Moving: Performs call test while moving in floor image. - Fixed: Performs call test at a certain measurement point inside a building. - TAB+JPG: Performs call test applying *.jpg or *.tab file as floor image. Call test is conducted while moving in floor image. - Real Time Map: Performs call test applying Google map as floor image. Call test is conducted while moving in floor image. 32

3-3. Inbuilding 1. Setting 2) Floor Setting a. Tap [Add] button, and [Add Floor] screen pops up. b. Configures Floor name. c. Tap [Select Image] button to select floor image from Camera/Gallery/Photos. d. Saved floor information can be edited or deleted by using [Edit] and [Delete] button. 33

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (1): Performs call test while moving in floor image. Test engineer marks test points during test. 1) Tap [Go to the image Map] button to start in-building test. Measure screen pops up. See the next pages. 34

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (2) 3) Select a floor to test. Floor names configured from Floor Setting are listed up. 2) Tap [Floor List] button. 35

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (3) When floor name is selected, floor image is sent to mobile. Icons of Mobile# are turned from red to green color. Only when all mobile# icons are in green color, in-building test is able to be started. Selected floor image is displayed in in-building test screen. Floor image can be zoomed in and out. RF Parameter can be configured. 36

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (4) 37

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (5) 4-1) Tap P1 point in floor image. 4-2) Add Point] screen pops up. 4-3) Tap [Add] button to confirm. 6) After P1 point is marked in floor image, tap [Start] button to start in-building AutoCall test. AutoCall setting should be completed prior to configure in-building test. 5) Every time a test engineer marks test point, [Add Point] screen pops up to confirm location once again. 38

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (6) 7) When the test engineer arrives at the next point (P2), tap floor image to mark P2. Then, repeat to move to the next points. 8) When the test engineer completes the latest point, tap [Done] button to stop in-building test. 39

3-3. Inbuilding 2. Measurement Test Type Setting 1) Moving Point Test (7) 9) AutoCall Stop screen pops up. Tap [OK] button to confirm. 40

3-3. Inbuilding 2. Measurement Test Type Setting 2) TAB + JPG Test (1): Performs call test applying *.jpg or *.tab files as floor image. Call test is conducted while moving in floor image. 1) Select [TAB+JPG] for Measure type. Names of tab and jpg must be identical. Floor Setting can be skipped for TAB+JPG type test. 41

3-3. Inbuilding 2. Measurement Test Type Setting 2) TAB + JPG Test (2) 3) Select a floor to test. Floor names configured from Floor Setting are listed up. 2) Tap [Floor List] button. 42

3-3. Inbuilding 2. Measurement Test Type Setting 2) TAB + JPG Test (3) 3) When *.tab and *.jpg files are successfully loaded, floor image is shown in in-building test screen properly. No floor list exists for TAB+JPG type test. 5) Tap [Start] button to start test. 4) Tap a start point. 43

3-3. Inbuilding 2. Measurement Test Type Setting 2) TAB + JPG Test (4) 6) Tap the latest point. 7) Tap [Done] button to complete test. 44

3-3. Inbuilding 2. Measurement Test Type Setting 3) Real Time Map Test (1): Performs call test applying Google map as floor image. Call test is conducted while moving in floor image. 1) Select [Real Time Mapping] for Measure type. Floor Setting can be skipped for Real Time Mapping type test. 45

3-3. Inbuilding 2. Measurement Test Type Setting 3) Real Time Map Test (2) 3) Select a floor to test. Floor names configured from Floor Setting are listed up. 2) Tap [Floor List] button. 46

3-3. Inbuilding 2. Measurement Test Type Setting 3) Real Time Map Test (3) 4) Tap a start point. No floor list exists for Real Time Mapping type test. 5) Tap [Start] button to start test. 47

3-3. Inbuilding 2. Measurement Test Type Setting 3) Real Time Map Test (4) 6) Tap the latest point. 7) Tap [Done] button to complete test. 48

3-3. Inbuilding 3. Use of ibwave (ibwc) file for Building Information 1) Importing ibwave (ibwc) file (1) *.ibwc file of ibwave can be applied for Building information. Imported ibwc files are listed in Building list adding the index of [ibwave Data]. 49

3-3. Inbuilding 3. Use of ibwave (ibwc) file for Building Information 1) Importing ibwave (ibwc) file (2) ibwave 사의 ibwc 파일을선택합니다. ibwc load가성공하면 Building Name 옆에 ibwave Data 로표시되면서 List에등록됩니다. Floor information is configured automatically by using floor information of ibwc file. 50

3-4. Map 1. Map (Normal) : Monitors test route, location of selected RF parameter, and etc by using different colors. Move current location at the center. Take GPS data of XCAL-Harmony tablet. Configure MAP settings. Show/Hide mobile call status at the bottom. Monitors RF value by using the selected mobile s GPS data. Tap 51

3-4. Map 1. Map (Satellite) : Monitors test route, location of selected RF parameter, and etc by using different colors. 52

3-4. Map 1. Map 1) Map Setting appearing when tapping [Settings] button in map. Assign identical RF items for all mobile. * Configure RF item for each mobile. * Set All Settings OFF. Configure colors of RF item ranges. 53

3-4. Map 1. Map 1) (Cont d) Map Setting appearing when tapping [Settings] button in map. [Call Event] : Turns On/OFF events to be displayed in map. [Drive Route] : Supports drive route file in *.kml format. Drive Route Update Local: Selects files saved in local folders of XCAL-Harmony tablet. Drive Route Update FTP: Downloads files from FTP server. Drive Route Clear: Cancels configured driver route. 54

3-5. IBFlex Scanner 1. GUI Main Menu buttons Syncs IBFlex Scanner to XCAL-Harmony via Bluetooth. Configures Scanner options. Displays scan result. Displays summarized scan result. Configures frequency setting automatically. Menu for beginner users. Displays status of logging and GPS. 55

3-5. IBFlex Scanner 2. H/W Setting menu 1) Scanner Control Connecting Scanner (1) 1) Tap [Detect Device] button to search Bluetooth scanner. 2) When scanner is searched, [Detection Process Completed.] is displayed. 3) When scanner is not searched, reboot scanner or tap [Detect Device] button to retry. 56

3-5. IBFlex Scanner 2. H/W Setting menu 1) Scanner Control Connecting Scanner (2) 4) Tap [Connect Device] button to sync scanner. 5) Select a scanner to sync. 57

3-5. IBFlex Scanner 2. H/W Setting menu 1) Scanner Control Connecting Scanner (3) 6) If scanner is synced successfully, [Control Result Code = 0 = Success] is displayed. 58

3-5. IBFlex Scanner 2. H/W Setting menu 2) Scanner Control Connecting Scanner GPS 2) If scanner GPS is successfully synced, color of GPS Connection button is changed. Longitude/Latitude data is displayed. [Get Location] button: Moves to the current location in map. 1) Tap [Connect GPS] to sync GPS of scanner. 59

3-5. IBFlex Scanner 2. H/W Setting menu 3) Scanner Control Scanner Device Info [Device Info] button: Displays detailed information of scanner. Version information of scanner is displayed. 60

3-5. IBFlex Scanner 3. Scan Setting menu (1) 7 scan types are supported. Up to 15 scan ID can be registered and managed for each scan type. Scan ID 1~15 - LTE Enhanced Top N Signal, Scan ID 21~35 - WCDMA Top N Pilot Scan ID 61~75 - CDMA Top N Pilot Scan ID 81~95 - EVDO Top N Pilot Scan ID 41~56 - GSM Color Code Scan ID 111~125 - RSSI Scan Scan ID 161~175 - Blind Scan 1) Tap [Scan Setting] menu. 61

3-5. IBFlex Scanner 3. Scan Setting menu (2) 1) Tap [LTE Enhanced TopN Signal] type. 4) When configuration is properly saved, [Unregistered] button is turned to [Registered]. 2) Setting screen pops up. Configure scanning options. Scan ID Scan Mode Protocol Type: Special option for LTE Enhanced TopN Signal type only. Band Code Channel Number Channel Stype It is recommended not to configure Advanced Setting as On for beginner users. 3) Tap [Save] button to save. 62

3-5. IBFlex Scanner 3. Scan Setting menu (3) 5) According to the scanner configuration, Scan ID, Scan Type, Band Code, Channel Number, Channel Style are displayed. 63

3-5. IBFlex Scanner 3. Scan Setting menu 1) Starting scanning (1) [Scan all IDs] button: Scans all Scan ID sequentially. [Stop all] button: Stops all Scan ID in progress. [Delete all]: Deletes all saved Scan ID. [Scan] button: Starts scanning of the selected Scan ID. [Delete] button: Deletes the selected Scan ID. 64

3-5. IBFlex Scanner 3. Scan Setting menu 1) Starting scanning (2) [Activate]: The corresponding Scan ID is currently conducting scanning job. 65

3-5. IBFlex Scanner 4. Scan View 2) Selects a Scan ID which is currently conducting scanning job. 1) Tap [Scan View] menu. 66

3-5. IBFlex Scanner 5. Total Summary Lists up all Scan ID which are currently conducting scanning job. Scan ID with no Cell IP for Top1 in scanning result is turned to yellow color. 1) Tap [Total Summary] menu. 67

3-5. IBFlex Scanner 5. Total Summary (Example) 68

3-5. IBFlex Scanner 6. Easy Mode (1) 3) Select a Band Code to scan. [Start Blind Scan] button: Searches Channel Number taking 1 ~ 10 minutes. 2) Select when Channel Number of Band Code is not checked. 3 tech are supported for Easy Mode. 1) Tap [Easy Mode] menu. 69

3-5. IBFlex Scanner 6. Easy Mode (2) 4) Searched Channel number are listed up. 5) Tap [Add Channels] button to add to Scan ID automatically. 70

3-5. IBFlex Scanner 6. Easy Mode (3) 6) Configured Channel Number is displayed. 71

3-5. IBFlex Scanner 6. Easy Mode Logging [Logging Start]: Saves scanning result in file. Logging file is saved in the folder of XCAL-Harmony-V2/Logging. Increased logging file size is monitored. 72

3-6. Logdata 1. Logdata 1) FTP Server Setting 2 1 1) Details of FTP Server configuration is displayed for uploading logdata. * FTP configuration is saved to synced XCAL-Mobile/Solo. 2) Configure FTP server for uploading logdata. 73

3-6. Logdata 1. Logdata 2) All Logupload 1 1) All logdata of selected date is uploaded at once. 74

3-6. Logdata 1. Logdata 2) Mobile# Logupload 2 Select a test date, and corresponding logdata (*.drm) is listed up. Select a logdata from the list, and the call result history of the corresponding *.drm is displayed in the right section. List up call result history of corresponding logdata created in the configured test date. 75

3-7. Settings 1. Configuration 1) Save/Load All Settings: Saves current setting, and applies saved setting. ON: Configuration file is automatically popped up when executing XCAL-Harmony. 76

3-7. Settings 1. Configuration 1) Save/Load All Settings: [Save All Setting] button saves all connected mobile information and scenario information. 77

3-7. Settings 1. Configuration 1) Save/Load All Settings: When [Load All Settings] is started, mobile synchronization and scenario configuration are started automatically. 78

3-7. Settings 1. Configuration 1) Save/Load All Settings: Existing setting file list (*.cfg) is automatically popped up and can be applied at the initial execution of XCAL-Harmony. 79

3-7. Settings 2. Scenario 1) Export/Import Scenario: Imports/Exports AutoCall scenarios to/from FTP server. 80

3-7. Settings 3. Logdata 1) Logging Option: Configures how to save logdata. All Scenarios: Saves all logdata in one *.drm file. Per file size: Saves logdata splitting in every configured file size. Per time: Saves logdata creating every configured time. Real Time Compress: Saves logdata compressing in real time. Naming Log File (Before AutoCall): Enter log file name when starting AutoCall test. 81

3-7. Settings 4. AutoCall 1) Automatic AutoCall Stop: Starts or Stops the whole AutoCall test process when XCAL-Mobile/Solo error is encountered. On: Terminates the whole AutoCall test process when the current AutoCall is stopped due to error of XCAL-Mobile/Solo. Off: Continues the remaining calls of AutoCall test even if the current AutoCall is stopped due to error of XCAL-Mobile/Solo. 82

3-7. Settings 5. Replay Mode 1) Replay Mode: Replicate past call test by replaying saved replay file. 83

3-7. Settings 5. Replay Mode 1) Replay Mode: Select a replay file and click [Start] button to replicate past test in time order. 84

3-7. Settings 5. Replay Mode 2) Make Replay File: Saves and replay AutoCall test conducted in XCAL-Harmony. ON: Saves replay file. Off: Does not save replay file. 85

3-7. Settings 6. Help 5) About: Shows License status of XCAL-Mobile/Solo currently synced to XCAL-Harmony. 86

Thank you 11 Floor, 190 Seohyen-Ro, Bundang-Gu, Seongnam-Si, Kyungki-Do TEL : +82-31-788-1700 FAX : +82-31-705-1246 www.accuver.com