HFR UPGRADE MANUAL FOR SX-2001/SA-2100(A/T) TO SX-2000(A/T)R DIGITAL CINEMA SERVER WITH NEW INTEGRATED MEDIA BLOCK SMS version 9.0 December 19, 2012
SX-2000(A/T)R Digital Cinema Server with New Integrated Media Block 2
TABLE OF CONTENTS 1. STANDARD UPGRADE PACKING AND RETURN LIST... 7 1.1 Standard Upgrade Packing List... 7 1.2 Standard Upgrade Return List... 7 2. BEFORE THE UPGRADE... 7 2.1 Backup... 7 2.2 Note... 7 3. REMOVING THE EXISTING COMPONENTS OF THE SX-2001/SA-2100... 8 3.1 Detach the mounting holder... 8 3.2 Cut the Cable Holder (plastic)... 9 3.3 Detach the Flat Cable... 10 3.4 Un-install the DCI Card... 10 3.5 Un-install the GPI/O Card... 11 3.6 Un-install the Sound Card... 12 3.7 Remove the Vented Back Plate... 12 3.8 Install the Back Plate for SX-2000 Model Configuration... 13 4. INSTALLING THE ADDITIONAL GIGABIT NETWORK CARD... 14 4.2 Install the Mounting Holder in the Server Case... 15 5. CABLE CONNECTIONS... 16 5.1 Ethernet Connections... 16 6. INSTALLING AND CONNECTING THE GDC INTEGRATED MEDIA BLOCK (IMB) INTO THE PROJECTOR... 17 6.1 IMB Components... 17 6.2 Installing the IMB into the Projector... 18 6.3 Inserting IMB to the Projector... 19 6.4 Connecting the IMB to the SX-2000(A/T)R server... 20 7. UPGRADE INFORMATION... 21 7.1 Note on the sha256 Certificate... 21 3
8. UPGRADE PROCEDURE... 21 8.1 Run the ServerID Upgrade... 21 8.2 Apply Upgrade Package 1... 22 8.3 Apply Upgrade Package 2... 24 9. SERIES 2 PROJECTOR SETUP... 26 9.1 Barco Series 2 Projector... 26 9.2 NEC Series 2 Projector... 26 9.3 Christie Series 2 Projector... 28 9.3.1 Christie Series 2 Projector 3D Settings... 31 10. IMB 3D MACRO SETTINGS CHANGES... 32 10.1 Barco Series 2 Projector... 32 10.2 NEC Series 2 Projector... 32 10.3 Christie Series 2 Projector... 33 11. AFTER THE UPGRADE... 33 12. SOM (Option, required for MPEG2 playback)... 34 12.1 Preparing the SOM OS... 34 12.2 How to Update the SOM OS Serial Number... 34 13. PREPARING FOR PLAYBACK... 35 14. PROJECTOR SETTING FOR MPEG2 PLAYBACK ON SOM... 37 15. CAUTION... 37 16. APPENDIX... 38 16.1 IMB Audio and GPIO Port Pin Layout... 38 4
Thank you for purchasing a GDC Digital Cinema Server SX-2000(A/T)R with Integrated Media Block from GDC Technology Limited. To upgrade for SX-2001/SA-2100 to SX-2000(A/T)R server with NEW Integrated Media Block, please review this Upgrade Manual. COPYRIGHT NOTICE Copyright 2012 by GDC Technology Limited All rights reserved. No part of this manual may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in a form or by any means, electronic, mechanical, photocopying, recording, magnetic, optical, manual or otherwise, or disclosed to third parties without prior written permission of GDC Technology Limited. MANUAL DISCLAIMER This manual is made with SMS version 9.0 and there might be slight differences depending on the software version the server is running. The contents, features and specifications stated in this manual are subject to change without notice due to continuous product development and improvements. In no other event shall GDC Technology Limited be liable for any loss of profit or any other commercial damages, including but not limited to special, consequential, or other damages. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. SOFTWARE LICENSE & SOFTWARE MANUAL AGREEMENT 1. This is an agreement between GDC Technology Ltd, ( Licensor ) and user ( Licensee ), who is being licensed to use the upgrade software referred to herein ( Software ) and software upgrade manual ( Manual ). 2. Licensee acknowledges that this is only a limited nonexclusive license. Licensor is and remains the owner of all titles, rights, and interests in the Software and Manual. 3. This License permits Licensee to install the Software on GDC genuine digital cinema servers that are either owned by the Licensee or maintained by the Licensee under a service contract with the server owner. Licensee will not make copies of the Software or Manual, nor allow copies of the Software or Manual to be made by others, without the prior written consent of Licensor. Licensee may make copies of the Software and Manual for the purpose of assisting the upgrade process itself, however all such copies should be destroyed at the end of the upgrade process. 4. THE SOFTWARE AND MANUAL ARE EACH PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. LICENSOR MAKES NO REPRESENTATIONS AS TO PERFORMANCE, ACCURACY, COMPLETENESS, CORRECTNESS, SUITABILITY OR VALIDITY OF THE SOFTWARE AND INFORMATION CONTAINED IN THE SOFTWARE UPGRADE MANUAL. IN NO EVENT SHALL LICENSOR BE LIABLE FOR ANY CLAIM, DAMAGES OR 5
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE OR SOFTWARE UPGRADE MANUAL.THE ABOVE-STATED LIMITED WARRANTY. REPLACES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND LICENSOR DISCLAIMS ALL IMPLIED. 5. In the event of any defect in the Software, Licensee's exclusive remedy is as follows: Licensee will return all copies of the Software to Licensor, at Licensee's cost, and Licensor will send Licensee a replacement copy of the Software. 6. Notwithstanding the foregoing, LICENSOR IS NOT LIABLE TO LICENSEE FOR ANY DAMAGES, INCLUDING COMPENSATORY, SPECIAL, INCIDENTAL, EXEMPLARY, PUNITIVE, OR CONSEQUENTIAL DAMAGES, CONNECTED WITH OR RESULTING FROM THIS LICENSE AGREEMENT OR LICENSEE'S USE OF THIS SOFTWARE. 7. Licensee agrees to defend and indemnify Licensor and hold Licensor harmless from all claims, losses, damages, complaints, or expenses connected with or resulting from Licensee's business operations. 8. Licensor has the right to terminate this License Agreement and Licensee's right to use this Software upon any material breach by Licensee. 9. Licensee agrees to return to Licensor or to destroy all copies of the Software upon termination of the License. 10. This License Agreement is the entire and exclusive agreement between Licensor and Licensee regarding this Software and Manual. This License Agreement replaces and supersedes all prior negotiations, dealings, and agreements between Licensor and Licensee regarding this Software and Manual. 11. This License Agreement is governed by the laws of California for all servers installed in the US and Hong Kong for servers installed in the rest of the world. 12. Licensor will not be liable for any errors, omissions, or any losses, injuries, or damages arising from use, misuse, improper use of the Software and Manual. Use of the Software and Manual is entirely at Licensee s own risk. 13. If there is any conflict between the English version of the Manual and any other language version of the Manual, the English version shall prevail. 14. This License Agreement is valid without Licensor's signature. It becomes effective upon the earlier of Licensee's signature or Licensee's use of the Software. By proceeding to use the Software, you agree to be bound by the terms and conditions contained hereinabove. 6
1. STANDARD UPGRADE PACKING AND RETURN LIST 1.1 Standard Upgrade Packing List Standard Upgrade HFR hardware package kit includes: 1. Upgrade package hardware checklist and software upgrade manual 2. NEW IMB 3. Cover plate for projector type 4. RJ45 Audio cable x 2 5. Traditional audio converter (RJ45 x 2 to 25pin female) 6. RJ45 GPIO cables x 4 (10 M) 7. CAT6 network cable x 1 (3 M) 8. Network card 9. New server s/n Label 10. Additional gigabit network card 11. New package boxes for delivery of upgrade kit 12. Transfer boxes for shipping packages of 3-5 upgrade sets 13. Return Item Checklist Note: RJ45 network cables should be of good quality CAT6 cables to guarantee proper network data transfer between the server and HFR IMB. Network cables with poor quality can cause video/audio jitter during playback. 1.2 Standard Upgrade Return List For SX-2001 / SA-2100 upgrade, the following items should be returned: 1. DCI card 2. Non-IMB Audio Card (with Cable) 3. GPIO Card x1 4. Old server s/n Label (SX-2001/SA-2100) 5. Boxes for return items 6. Return item checklist 2. BEFORE THE UPGRADE 2.1 Backup Create a snapshot of the OS partition with Rescue mode before you try to apply the upgrade. Note that the Rescue mode function is only available for SATA OS hard disk. If you are unfamiliar with this procedure, please refer to the document GDC_system_backup_and_recovery. 2.2 Note SX-2000(A/T)R server serial number and HFR IMB serial number should be the same, please request this from your service provider. 7
3. REMOVING THE EXISTING COMPONENTS OF THE SX-2001/ SA-2100 Mounting Holder DCI Card GPI/O Card Sound Card Figure 1 Hardware Configuration of the SX-2001/ SA-2100. 3.1 Detach the mounting holder Figure 2 Detach the mounting holder. 1. Unscrew the mounting holder as indicated in Figure 2. 2. Detach the mounting holder. 8
3.2 Cut the Cable Holder (plastic) Figure 3 Cut the cable holder (plastic). 1. Refer to the circled area in Figure 3, kindly cut the cable holder (plastic tie). To access the power pin connector for the DCI card s fan. 9
3.3 Detach the Flat Cable Figure 4 Detach the flat cable. 1. Detach the pin head of Flat cable from the DCI side as indicated in Figure 4. 3.4 Un-install the DCI Card Figure 5 Un-install the DCI card. 1. Un-install the DCI card by un-securing the screw. 10
Figure 6 Take out the DCI card and remove the power pin head. 2. Take out the DCI card from the PCI slot and set aside. 3. Kindly remove the power pin head (red circle indicated in Figure 6) which is connected to the fan on the DCI card to the pin head of the power supply. 3.5 Un-install the GPI/O Card Figure 7 Remove the GPI/O card. 1. Unsecure the screw as indicated, and then gently remove the GPI/O card. 11
3.6 Un-install the Sound Card Figure 8 Un-install the sound card. 1. Same procedure, remove the sound card by un-securing the screw as indicated in Figure 8. 3.7 Remove the Vented Back Plate Figure 9 Remove the vented back plate. 1. Remove the vented back plate by un-securing the screw. 12
3.8 Install the Back Plate for SX-2000 Model Configuration Figure 10 Install the back plate. 1. Install the back plate for the indicated positions, for covering the Back panel of casing since the PCI slots are not in use. 13
4. INSTALLING THE ADDITIONAL GIGABIT NETWORK CARD 4.1 For TMS/LMS Connection (Without SOM) 1. Insert the additional gigabit network card into the same PCIe slot that was used by DCI Card. The tested gigabit network card model is 'INTEL Gigabit CT Desktop Adapter'. Gigabit network card Figure 11 Insert the additional gigabit network card. 2. After the network card is installed a software upgrade is required. This file can be found here: ================================================================= Link URL: http://visitor:wiije67@ftp.gdc-tech.com/~service/9x/upgrade-sx2000ar-9x-networkcard- 20121109.tgz.enc User: visitor Password: wiije67 md5sum: 2fc13509c8c172be25f24c73dd717e0e upgrade-sx2000ar-9x-networkcard- 20121109.tgz.enc Upgrade password: 20121109 ============================================================== 3. Boot up the server and apply 'upgrade-sx2000ar-9x-networkcard-20121109.tgz.enc' on 7.8.X Server SMS->Configuration->Assistance->USB. This upgrade prompts an error if the server eth0 or eth1 has 192.168.1.x IP. 4. It will prompt user with the IP changes (eth1: 192.168.1.13 eth2: 192.168.3.14) and require user confirmation before proceeding. 5. Whenever the additional network card is pulled out and put back into the slot, or a different additional card is used for replacement, this upgrade must re-run on the AR server. Server eth1 is required for IMB data transfer during playback, its IP is recommended to remain at 192.168.1.13 after upgrade. 14
Server eth2 can be updated to a different IP other than 192.168.3.14 for other purposes, e.g. TMS data transfer. However, server eth2 should not be using 192.168.1.x or 192.168.2.x as these two IP ranges are reserved for IMB. 6. Server eth1 is directly connected to IMB Ethernet 2. 7. Server eth0 is connected to projector Ethernet port (either directly or via a switch). 8. Server eth2 (from the installed gigabit card) can be used for transferring content from the TMS/LMS as in normal operation. 4.2 Install the Mounting Holder in the Server Case L leg Figure 12 Install the mounting holder in the server case. 1. Un-secure the screws and take out the L legs from the holder. Figure 13 Secure the screws. 2. Place in the mounting holder, and then secure the screws as indicated in Figure 13. 15
5. CABLE CONNECTIONS Once the server has been placed in the desired location, the cables described below should be attached (See Figure 14). 1 VGA cable used for connecting to external touch screen monitor 2 Power cables 3 Network connections: a. eth0 Projector b. eth1 IMB interface c. eth2 Management 4 USB slot used for connecting to external touch screen monitor 5.1 Ethernet Connections Figure 14 SX-2000 rear panel with cables attached. 1. Make sure the IMB is powered up inside the projector correctly. 2. SX-2000(A/T)R eth0 IP must NOT be 192.168.1.X (recommend it to be 192.168.0.X). 3. SX-2000(A/T)R eth0 is connected to projector Ethernet (either directly or via switch). 4. SX-2000(A/T)R eth2 IP must NOT be 192.168.1.X. 5. SX-2000(A/T)R eth1 is directly connected to IMB Ethernet 2. eth2 is available after installing the additional gigabit network card. IMPORTANT NOTE: Projector should not use 192.168.2.X IP as this IP range is reserved for IMB internal use. If projector IP is set to 192.168.2.X, the server will not be able to connect to the security manager (SM) after upgrade. 16
6. INSTALLING AND CONNECTING THE GDC INTEGRATED MEDIA BLOCK (IMB) INTO THE PROJECTOR Note: If the projector comes with the GDC IMB pre-installed, the instructions in Section 6.2 can be skipped. Refer to Section 6.4 to connect the network cable to the IMB on the projector and to the SX-2000(A/T)R server. If the projector does not have the GDC IMB installed, follow the steps below to install the IMB into the projector. This section of the manual deals with installing the IMB into the Projector, and connecting the IMB interface and network cables to the IMB and projector respectively. 6.1 IMB Components The GDC Integrated Media Block comes with a network cable (see Figure 15) for connecting to the SX-2000(A/T)R server. The IMB is shown in Figure 16. Figure 14 Network cable for GDC IMB Figure 16 GDC Integrated Media Block (IMB) 17
6.2 Installing the IMB into the Projector Remove existing interface board/placeholders from projector Before installing, check the figures below to ensure proper placement of the IMB. Figure 17 shows an interface board (with SMPTE 292 inputs) connected to a Barco projector. This board must be removed in order to install the IMB. Remove for IMB Figure 17 IMB Placement on Barco projectors Figure 18 shows the location where the IMB should be installed on a Christie projector. Remove any existing interface boards or placeholder faceplates from this position before installing the IMB. IMB installed here Figure 18 IMB placement on Christie projectors. 18
Figure 19 shows the location where the IMB should be installed on a NEC projector. Remove any existing interface boards or placeholder faceplates from this position before installing the IMB. IMB installed here Figure 19 IMB placement on NEC projectors Please refer to the projector manuals for more details on preparing the projector for IMB installation. 6.3 Inserting IMB to the Projector Make sure the projector is powered off before installing the IMB on the projector. Insert the IMB as shown in Figure 20. Figure 20 Inserting the IMB into the projector The IMB should slide into the projector on the rails provided by the IMB slot, and the IMB faceplate should be flush with the other existing faceplates once properly inserted. 19
6.4 Connecting the IMB to the SX-2000(A/T)R server The IMB on the projector and the SX-2000(A/T)R server must be connected for proper operation. There are two cables to be connected between the projector and the SX- 2000(A/T)R server: CAT-5E network cable to connect the network between the projector and the server. The projector and server can also be connected through a network switch. Network cable for connecting the IMB installed on the projector and to PCI-e slot on the server back panel. To insert the network cable into the IMB or server, push the network cable connector firmly into the respective network port. Connecting to the IMB and the projector Connect the network cable as shown in Figure 21. Figure 21 Connecting cables on the projector. Connect the network cables as shown in Figure 22. Figure 22 Connecting cables on the SX-2000(A/T)R server. 20
7. UPGRADE INFORMATION ServerID upgrade Upgrade package1 Upgrade package2 upgrade-serverid_axxxxx tgz.enc upgrade-sx2000ar-step2- [YYYYMMDD].tgz.enc upgrade-sx2000ar-buildxx- [YYYYMMDD] -incr.tgz.enc Upgrade should be applied on 7.81 to 7.83 Upgrade estimated total time 15 to 20 mins 7.1 Note on the sha256 Certificate After upgrading SX-2001/SA-2100(A/T) to SX-2000(A/T)R for HFR IMB, the server sha256 certificate will be updated so new KDMs must be issued with the updated sha256 certificate. Previous KDMs (before upgrade) issued for this server may not be seen for ingest on Content Manager. 8. UPGRADE PROCEDURE 8.1 Run the ServerID Upgrade ServerID upgrade prepares your server for the DCI software upgrade and MUST run before running the main upgrade. The following upgrade package must run based on your serial number: A00000 A00999 A01000 A01999 A20000 A20999 upgrade-serverid_a00xxx tgz.enc upgrade-serverid_a01xxx tgz.enc upgrade-serverid_a20xxx tgz.enc 21
8.2 Apply Upgrade Package 1 1 Figure 23 Upgrading from an USB disk. 1 Install from SMS->Configuration->Assistance->USB Disk 2 Figure 24 Select upgrade package. 2 Enter password and select the correct upgrade package. 22
3 Figure 25 Upgrade completed. 3 The upgrade will take under one minute, then a window Upgrade completed. Click OK to reboot will pop up. User should unplug the USB drive and click OK to reboot the system. 23
8.3 Apply Upgrade Package 2 Case 1: If the system (server/imb/projector) is already a SX-2000(A/T)R system, please ensure the system (server/imb/projector) is able to playback a DCP from the server right before applying the incremental upgrade to a newer build version. This is to guarantee the IMB will be able to access server storage (no matter through server eth1 or server eth2) successfully for some of the upgrade files. Server eth2 is available when the additional gigabit network card is installed in the server (section 4). If the IMB is not able to access the server storage during the incremental upgrade, i.e. without checking that the system is able to playback a DCP from the server, the upgrade may fail and the IMB LED displays RED color after reboot. When this happens, only a GDC authorized personnel can recover the system. Case 2: When converting the SX-2001/SA-2100(A/T) server to work with HFR IMB, please ensure the incremental upgrade package version is the same as the IMB build version. e.g. if the IMB build version is build55 and the incremental upgrade package version is given as build56, please request build55 upgrade package when converting a SX-2001/SA-2100(A/T) server to work with the IMB of version build55. After successfully converting the server and IMB, then follow case 1 to update to a newer build 56. 2 Figure 26 Apply package 2. 1 After reboot, go to SMS->Configuration->Assistance->USB Disk again. 2 Apply package 2 as indicated in Figure 25. 3 Same as Section 8.2, reboot the server after the upgrade. 24
4 Figure 27 Press password to log in SMS. 4 The above screen will show up after rebooting, and requires entering the password to enter SMS interface. 25
9. SERIES 2 PROJECTOR SETUP To work with the GDC IMB, the projector must be set up according to the requirements of the projector manufacturer. 9.1 Barco Series 2 Projector No system configuration is required for Barco Series 2 projector to work with the GDC IMB. The Service Door/Marriage Tamper on the server must be cleared before the IMB can be used for playback. In order to use the IMB for content playback, the INPUT source of the projector macros must be set to IMB (See Figure 28). Figure 28 INPUT source settings on Barco Series 2 projector. 9.2 NEC Series 2 Projector In order to configure an NEC Series 2 projector to work with IMB, the following steps must be taken: 1. Switch on the projector so that it is in STANDBY mode. 2. Use the Digital Cinema Communicator for S2 Windows software provided by NEC to connect to the projector. 3. Select [Start] [Mode] [Service] and enter the Service password to activate service mode operation. (See Figure 29) 26
Figure 29 Service mode on NEC Digital Cinema Communicator 4. Select [Setup] [Option Slot] on the Digital Cinema Communicator and select IMB for Slot A in Option Slot Setting. (See Figure 30) 4 Figure 30 Option slot settings on NEC Digital Cinema Communicator 5. Select [Start] [Power] [On] to power on the projector. 27
6. After the projector has powered on successfully, the following steps must be taken at the projector front panel: a. Press and hold the Menu button until the front panel LCD prompts for a password b. Enter the Service user password using the channel buttons. c. Select [Menu] [Configuration] [Installation] [NewRouterSetup] and select [Execute]. 7. Clear the Service Door/Marriage Tamper on the server. In order to use the IMB for content playback, the INPUT source of the projector macros must be set to IMB. 9.3 Christie Series 2 Projector When the IMB is installed into a Christie Series 2 projector, the following steps must be taken in order for GDC server to playback with the Christie Series 2 projector: Note: Ensure the projector is powered ON before proceeding. 1. Clear the projector s marriage tamper: a. Log in to the "Marriage" account on the projector TPC. Select Menu Service Setup Marriage to start the Marriage wizard (see Figure 31). Click the [Next] button to proceed to the Marriage Checklist window. Figure 31 Projector marriage wizard on Christie projector TPC 28
b. Read and perform the actions listed in the Marriage Checklist. In the Marriage Checklist window (see Figure 32), the system checks that all tamper switches are secure and lists items that you must check to ensure the projector is secure before proceeding. Click the [Next] button to proceed to the Arming window. Figure 32 Marriage checklist c. Arm the marriage. In the Arming window, click the Arm Marriage button (refer to Figure 33). A 30 second count-down timer begins. The LED in the Marriage button on the PI Board will flash green during this count-down. You MUST press the Marriage button on the PI Board within this 30 second window in order for the marriage to take effect. When the Marriage button is pressed, the LED button will change to a solid green to indicate a successful marriage. 29
Figure 33 Arm Marriage and Marriage countdown d. The Finish window states the success of the marriage. Click the Finish button to return to the Main panel. 2. Clear the Service Door/Marriage Tamper on the server. All 3D IMB channels on the Christie Series 2 projector should use the IMB input and 4:4:4 (RGB) input data format (see Figure 34). 30
Figure 34 Projector input settings for Christie projectors 9.3.1 Christie Series 2 Projector 3D Settings The 3D macros for Christie Series 2 projectors should be configured with the following settings for 3D Input Control (see Figure 35): 3D Sync Input Mode: Use Line Interleave (first line=left, second line=right) L/R Display Reference: Not Used Frame Rate: 6:2 L/R Display Sequence: Left (L1R1 L2R2) Figure 35 3D macro settings for Christie projectors 31
The settings for 3D output control ( 3D Sync Polarity, Dark Time, Output Delay and Phase Delay ) should be customized according to the type of 3D system used (RealD, XpanD or Dolby3D). 10. IMB 3D MACRO SETTINGS CHANGES Server software version 9.0 makes changes to the IMB 3D output format. The following projector macro changes are required to support these changes. Note: These are required changes on the projector. IMB 3D output will not function properly unless these changes are made. Software version 9.0 enables IMB 3D output in 4:4:4 format. This can be enabled on the SMS configuration page, by selecting SMS Configuration CineCanvas IMB 3D 4:4:4 (see Figure 36). Figure 36 IMB 3D 4:4:4 configuration on SX-2000(A/T)R server 10.1 Barco Series 2 Projector The IMB 3D macros on existing Barco S2 projectors are configured to use the GDC_IMB_422.input file. If the IMB 3D 4:4:4 option is checked in SMS configuration, all IMB 3D macros should use the input file named Mediablock.input. 10.2 NEC Series 2 Projector The IMB 3D macros on existing NEC Series 2 projectors are configured for 4:2:2 input. If the IMB 3D 4:4:4 option is checked in SMS configuration, all IMB 3D macros should be changed to use 4:4:4 input. 32
10.3 Christie Series 2 Projector The IMB 3D 4:4:4 option in SMS configuration must be checked. No additional configuration is required for the projector. 11. AFTER THE UPGRADE 2 Figure 37 Server eth1. 1 After the upgrade is completed, powercycle both the server and projector with IMB. 2 IMB marriage and service door clearance are recommended to be done on the server SMS->Configuration->Maintenance Access- >General->IMB (For IMB marriage, please refer to the SX- 2000(A/T)R Installation Manual as process will depend on projector manufacturer and software version.) 33
12. SOM (Option, required for MPEG2 playback) If the SOM option is included with the IMB, please follow the steps in this section to integrate. 12.1 Preparing the SOM OS Please request from your service provider to produce the SOM OS for the IMB with the corresponding serial number. Note that the upgrade files shall be downloaded and put inside a USB stick and insert into one of the front USB port on IMB after SOM is booted up. To verify SOM boot up properly, vncviewer projectorip:43752 should see AdminPanel on SOM. Below are the steps to get SOM OS up to date: 1. Request somid package for the correct serial number on SOM. 2. Apply the somid package on SOM (not server). AdminPanel Diagnostics/Maintenance- Software Upgrade (vncviewer projectorip:43752 to see the SOM User Interface). 3. Apply the SOM software upgrade package (e.g. named as 'upgrade-som-step3-build56-20120911.tgz.enc') on SOM (not server) in the same way as Step 2. 4. SOM (not server) AdminPanel->Diagnostics/Maintenance->Software Upgrade should be used for future SOM upgrades. 12.2 How to Update the SOM OS Serial Number In the case that the SOM OS received from production does not have any serial number (SOMp2:/usr/local/dsr/serial does not exist/exists but empty) or you need to use a SOM OS for a different serial number on your IMB. Below are the notes to update the SOM OS serial number: 1. Simply use a CF card reader on a PC and create SOMp2:/usr/local/dsr/serial (without any suffix) on the CF card, the file shall contain the same serial number as IMB, e.g. A01357. 2. Put the CF card back onto the IMB and follow Section 12.1 to get the SOM OS up and running. 3. The SOMp2:/usr/local/dsr/serial file will be deleted after the SOM boots up. 4. When the SOM OS serial number is updated, please re-run the steps from section 12.1. 34
13. PREPARING FOR PLAYBACK 1 Figure 38 Turn off the server. 1 Click server SMS Shutdown Shutdown to turn off the server. After the server is turned off, the IMB/SOM on projector will be down as well, so the projector must be off. 2 Power off the projector. 3 Power on the projector. 4 Power on the server. 35
5 Figure 39 Configure Projector 1 TI IP. 5 Configure Projector 1 TI IP on server SMS Configuration Cinecanvas. 6 Figure 40 SMS Interface. 6 Once 'SM connected' shows up on the server SMS, the system is ready to playback both JPEG2000 and MPEG2 contents. 36
14. PROJECTOR SETTING FOR MPEG2 PLAYBACK ON SOM 1 1 Input format is '422 12 bit'. Figure 41 Projector setting [Input format]. 2 Figure 42 Projector setting [Active pcf Data]. 2 PCF should be 'MXFI_185' or 'MXFI_239'. 15. CAUTION Please use Server SMS Shutdown Shutdown to turn off the server and IMB. After the server and IMB are turned off, the projector may indicate communication lost to the IMB; the projector must be rebooted for next playback. 37
16. APPENDIX 16.1 IMB Audio and GPIO Port Pin Layout AES Audio GPIO Figure 43 IMB audio and GPIO port pin layout. 38
GDC Technology Offices USA (Los Angeles, CA) 1016 West Magnolia Boulevard Burbank,CA 91506, USA Tel: +1 818 972 4370/ +1 877 743 2872 (Toll Free) USA (Sterling, VA) 21155 Whitfield Place, Suite 207, Sterling, VA 20165, USA Tel: +1 877 337 0868 (Toll Free) Spain (Barcelona) Av. Diagonal, 177, 9th Floor 08018 Barcelona, Spain Tel: +34 93 238 14 10 Hong Kong Unit 1-7, 20th Floor, Kodak House II, 39 Healthy Street East, North Point, Hong Kong Tel: +852 2523 6851 Japan (Tokyo) 7F Nishino Kinryo Bldg, 4-9-4, Hatchobori, Chuo-ku, Tokyo 104-0032, Japan Tel: +81 3 3523 2650 Singapore 10 Ubi Crescent, Ubi Tech Park, Lobby B, #06-25, Singapore 408564 Tel: +65 6222 1082 China (Shenzhen) 5th Floor GDC Building, No.9 Hi-tech Middle 3 Road, Science & Technology Park, Nanshan District, Shenzhen, P.R. China 518057 Tel: +86 755 8608 6000 China (Beijing) Rm. 609-618, Office Building, 20# Xinde Street, Xicheng District, Beijing, P.R. China 100088 Tel: +86 10 6205 7040 Email: info@gdc-tech.com Website: www.gdc-tech.com ISO 9001 QMS Cert. No. CN09/32221 GDC manufacturing facility is ISO 9001: 2008 certified. Copyright 2012 GDC Technology Limited. All rights reserved. All trademarks listed in this manual are properties of their respective owners. Specifications are subject to change without notice due to ongoing product development and improvement. UM-0150-1212-V1E