Avy P460 Modulr Multilyer Switch Quick Strt Guide Importnt Informtion Unpck the Chssis Position the Chssis 1 2 3 Note: Refer to Importnt Informtion before strting the instlltion Instll the Supervisor Module nd PSU Configure the Switch Run the Embedded Web (optionl) 4 5 6 IP Telephony Contct Centers Unified Communictions Services
Importnt Informtion 1 Before instlling or removing ny components of device, or crrying out ny mintennce work, you must red the sfety informtion provided. Notes, Cutions nd Wrnings Text with the symbol contins helpful informtion or hints or reference to mteril in other documenttion. Cution: Tke cre. You could do something tht my dmge equipment or result in loss of dt. Wrning: This mens dnger. Filure to follow the instructions or wrnings might result in bodily injury. Ensure tht you re qulified for this tsk nd hve red nd understood ll the instructions Sfety Informtion Dnger: To void injury, Avy recommends tht two people lift or move the switch. A fully loded P460 switch weighs t lest 100 lbs (45 kg). Cution: The Avy P460 switch nd modules contin components sensitive to electrosttic dischrge. Do not touch the circuit bords unless instructed to do so. Do not leve ny slots open. Use the blnking pltes supplied to cover empty slots. Do not insert ny objects into the P460 chssis other thn specificlly designed Avy products. Wrning: The fns re on whenever the power is on in the chssis, whether supervisor modules re instlled or not. Keep your fingers nd other objects cler of the fns when removing the Fn module. The fns continue to turn briefly fter you hve removed the module.
Power Supplies CAUTION: Risk of electric shock. Disconnection of one power supply cord disconnects one power supply module only. To isolte unit completely from the mins disconnect ll power supply cords. 1 ACHTUNG: Gfhr des elektrischen Schocks. Entfernen des Netzsteckers eines Netzteils legt nur dieses Netzteil spnnungsfrei. Um lle Einheiten spnnungsfrei zu mchen. Sind die Netzstecker ller Netxteile zu entfernen ATTENTION: Risque d'électrocution. Le débrnchement d'un câble d'limenttion ne déconnecte qu'un seul module d'limenttion. Pour isoler complètement l'unité du secteur, débrnchez tous les câbles d'limenttion. FCC Notice This equipment hs been tested nd found to comply with the limits for Clss A digitl device, pursunt to prt 15 of the FCC Rules. These limits re designed to provide resonble protection ginst hrmful interference when the equipment is operted in commercil environment. This equipment genertes, uses, nd cn rdite rdio frequency energy nd, if not instlled nd used in ccordnce with the instruction mnul, my cuse hrmful interference to rdio communictions. Opertion of this equipment in residentil re is likely to cuse hrmful interference in which cse the user will be required to correct the interference t his own expense. Chnges or modifictions to this equipment not expressly pproved by Avy Inc. could void the user s uthority to operte the equipment. Wrrnty: Avy Inc. provides limited wrrnty on this product. Refer to your sles greement or other pplicble documenttion to estblish the terms of the limited wrrnty. In ddition, Avy s stndrd wrrnty lnguge s well s informtion regrding support for this product, while under wrrnty, is vilble through the following website: www.support.vy.com. Every effort ws mde to ensure tht the informtion in this document ws complete nd ccurte t the time of printing. However, informtion is subject to chnge.
2 Unpck the Switch Check the pckge contents for the following: Equipment One P460 chssis with fn module. If you purchsed n Avy P460ML-CFG (Mteril code 700255003, PEC Code 4548-009), then one Supervisor Module, PSU nd the Fn Module re lredy instlled. Ethernet connection cbles re not supplied. Documenttion Avy P460 Quick Strt Guide (this document). Avy P460 Relese Notes. Avy P460 Documenttion nd Utilities CD. Avy Wrrnty nd License Agreement. CD Contents User s Guides Avy P460 Instlltion nd Mintennce Guide Avy P460 Configurtion Guide Avy P460 Reference Guide Avy MSNM P460 Mnger User s Guide Auxiliry Files for the use with the Device Mnger Jv plug-in Help files Adobe Acrobt Reder This ppliction llows you to view nd print the User s Guides on this CD If ny items re missing or dmged, contct your supplier.
Position the Switch Environmentl Prerequisites Dnger: To void injury, Avy recommends tht two people lift or move the switch. A fully loded P460 switch weighs t lest 100 lbs (45 kg). You cn position the Avy P460 in free-stnding mode on suitble shelf or tble, or mount it in stndrd 19-inch equipment rck in wiring closet or equipment room. When deciding where to position the chssis, ensure tht: It is ccessible nd cbles cn be connected esily nd ccording to the configurtion rule. Cbles re wy from sources of electricl noise such s: rdio trnsmitters brodcst mplifiers power lines fluorescent lighting fixtures. Wter or moisture cnnot enter the cse of the chssis. There is free flow of ir round ll sides the chssis. The vents on the sides of the cse re not blocked. The tble or shelf cn hold the weight of the chssis with the PSUs nd modules. The environmentl conditions mtch the requirements listed in Tble 1. Refer to the Avy P460 Instlltion nd Mintennce Guide for dditionl informtion. 3 Tble 1 Environmentl Requirements Ambient temperture 23 o to 122 o F (-5 o to 50 o C) Reltive humidity Minimum clernce for ventiltion Weight support 5% to 95%, non condensing 2" (5 cm) on ech side 50 lb. (23 kg) to 100 lbs (45 kg) The power source mtches the specifictions shown in Tble 2. Tble 2 Voltge AC Power Requirements 100 to 240 VAC, 50/60 Hz Current for one Avy MPS4603-AC 300 W PSU 3.9 A@100 VAC 1.5 A@200VAC
Tble 3 Height Width Depth Dimensions 10U (17.5", 444.5 mm) 17.4" (442 mm) 15" (375 mm) Instlling the P460 on Tble Top Plce the system on surfce tht supports t lest 100 lbs (45 kg). 1 Instll the supplied rubber feet to the bottom of the switch, plcing the feet in the squre recesses provided. See Figure 4. Clen the surfce of ny oils or residue before pplying the feet. Figure 4 Tble-Top Instlltion 3 Rubber feet 2 Ensure tht ll the preinstlled components re firmly instlled in the chssis. These include: Supervisor modules Power supply Fn module Cution: Do not plce other equipment on top of the P460.
Rck Mounting (optionl) Dnger: To void injury, Avy recommends tht two people lift or move the switch. A fully loded P460 switch weighs t lest 100 lbs (45 kg). You cn mount the Avy P460 in stndrd 19" rck either in front-mount or mid-mount positions with the brckets supplied with the chssis. The brckets re symmetric: you cn fix either brcket one either side. Figure 5 shows the two mounting positions: Figure 5 P460 Front-Mount nd Mid-Mount Positions (side view) Front-Mount 5.5 (140 mm) Mid-Mount 3 b b Front Front Key Rck b P460 switch The chssis height is 10U.
P460 Rck mounting procedure: 1 Position the brckets s shown in Figure 6 Figure 6 Positioning the rck-mounting brckets b P460 3 3 3 b Key b Front-mount position Mid-mount position 2 Firmly fix the brckets to the chssis with the screws provided. Use five screws for ech brcket. 3 Position the switch in the rck. 4 Fsten the switch in the rck with the screws provided. The screw size is 8-32x¼ Cution: Do not plce other equipment on top of the P460
Cble Guide Instlltion You cn use the cble guide to tidy cbles from the Supervisor nd I/O modules. The cble guide is symmetric: you cn instll the brcket on either side of the switch. Avy recommends tht you instll the cble guide on the left side of the switch to llow esier ccess to the fn module. You need to instll the rck mounting brckets before you cn instll the cble guides. Instll the switch in the rck before instlling the cble guide. Secure the cble guide to the rck mounting brcket using the cptive screws on the cble holder. See Figure 7. Figure 7 Instlling the Cble Guide Left side of chssis Right side of chssis 3 b b Key Cble Guide b Rck-mounting brcket
Instll the Supervisor Module nd PSU Instll the Supervisor Module If you purchsed n Avy P460ML-CFG (Mteril code 700255003, PEC Code 4548-009), then one Supervisor Module, PSU nd the Fn Module re lredy instlled. Figure 8 shows the positions of the SPV Supervisor instlled in the P460 chssis. Figure 8 Loction of the Avy P460 Supervisor Modules 4 You cn instll Supervisor modules in the top two slots 1 nd 2 only. Cution: Do not leve ny slots open. Use the blnking pltes supplied to cover empty slots. Cution: The Supervisor modules contin components tht re sensitive to sttic dischrge. Hndle the module by the edges only. Use pproprite nti-sttic equipment when hndling the modules.
3 3 Figure 9 Instlling the P460 Supervisor Module P460 b Key b Open locking hndle Closed locking hndle To instll Supervisor module: 1 Remove the blnking plte. 2 Open the locking hndles t the edge of the front pnel. 3 Position the module in the slot. See Figure 9. 4 Gently slide the module in. 5 Close the locking hndles. 6 Gently tighten the screws. For informtion on configuring redundnt supervisor modules, refer to M460ML-SPV Supervisor Module Redundncy on pge 35 of the Avy P460 Instlltion nd Mintennce Guide. 4
Instlling PSU Cution: Do not leve ny PSU slots open. Use the blnking pltes supplied to cover empty slots. 4 Use the hndle on the front pnel of the PSU to lift it. You cn instll the PSU in ny of the three slots. 1 Remove the blnking plte by unscrewing the four retining screws nd gently tugging the plte towrds you. 2 Position the PSU with the lbel fcing up nd to the right. 3 Gently slide the PSU bck until the socket on the bck of the PSU engges in the plug on the chssis. Ensure the guiding pins on the front pnel of the PSU lign with the holes on the front pnel of the P460 chssis. 4 Gently tighten the screws on the PSU. Turn on the Switch Once you hve instlled the supervisor module nd PSU, you cn turn on the switch: 1 Connect the PSU to the electricity supply. 2 Set the rocker switch on the front pnel of the PSU to I to turn the switch on. The LED on the front pnel of the PSU is lit green. The fns strt The boot process strts: Stge PWR LED OPR LED ACT LED 1 ON Flshes for bout 50 seconds OFF 2 ON ON fter bout 30 seconds 3 ON ON If you hve instlled two supervisor modules, the boot process is s follows: Acttive supevisor module Second supervisor module Stge PWR LED OPR LED ACT LED PWR LED OPR LED ACT LED 1 ON Flshes for OFF ON Flshes for OFF 2 3 ON ON bout 50 seconds ON ON fter bout 30 seconds ON ON bout 50 seconds ON ON fter bout 30 seconds Flshes* *Supervisor in hlted mode Refer to the Avy P460 Instlltion nd Mintennce Guide for further informtion. The P460 is now redy for opertion with its defult settings (see Tble 12, Defult System Prmeters ). If you wish to configure the switch, see Configure the Switch.
Configure the Switch Before you cn set up the P460 you must instll t lest one supervisor module nd PSU nd then turn on the switch. You cn configure the switch vi sidebnd, inbnd or outbnd interfces. Connecting the Seril Console Port Ech Avy P460 supervisor module hs one seril port on the front pnel for connecting terminl, terminl emultor, or modem. The seril port on the front pnel is lbeled RS-232 nd hs n RJ-45 socket. 1 Insert the RJ-45 plug on the console cble into the Console port of the supervisor module. 2 Insert the other end into the RJ-45 socket in the supplied DB-9 dpter. 3 Insert the DB-9 plug into the seril (COM) port on the PC or terminl. To connect modem, use the cble nd n RJ-45 to DB-25 dpter. The cble nd two dpters re in the Avy P460 ccessory set supplied with the switch. Avy CLI Hints nd Tips CLI Commnd Conventions CLI commnds for you to enter re in the computer bold font. Informtion displyed on screen s well s prmeters of commnd re displyed in computer font. Prmeters tht you enter re in pointed brckets <>. Alternte but mndtory keywords re grouped in brces {} nd seprted by br. Optionl keywords re in squre brckets [ ] nd options re seprted by br. If you enter n lphnumeric string of two words or more, enclose the string in quotes. The Avy CLI hs severl fetures which improve ese of use: To disply ll commnds vilble in context type question mrk. To disply ll commnds strting with certin string, type the first few letters followed by question mrk. To get help contining ll commnds prmeters with their legl vlues s well s its syntx nd n exmple, type question mrk t the end of commnd or t the stge where it is unique. Use the Tb key to complete n unmbiguous commnd. 5
Estblishing Console Connection with the P460 Figure 10 M460ML-SPV Supervisor Module Seril Console Port 5 Perform the following steps to connect terminl to the P460 Seril Console port for configurtion of switch prmeters: 1 Use the seril cble supplied to ttch the RJ-45 RS-232 console connector to the Console port of the ctive M460ML-SPV module. Connect the DB-9 connector to the seril (COM) port on your PC/terminl. The ctive Supervisor module is indicted by the ACT nd OPR LEDs being lit. 2 Ensure tht the seril port settings on the terminl re: 9600 bud 8 bits 1 stop bit no prity. If you reset or powered up the switch fter connecting nd configuring the terminl, Welcome to P460 ppers followed by the Login Nme prompt. If the login prompt does not pper, press key on the terminl. 3 Enter the defult login: root. The Pssword prompt ppers 4 Enter the user level pssword: root. If you connect your terminl to the Stndby SPV (OPR nd PWR LEDs re on, ACT LED is off), you cn get ccess to ll the CLI commnds by opening Session to the Active SPV. Estblishing Telnet Connection (Outbnd) Figure 11 M460ML-SPV Supervisor Module Fst Ethernet Console Port Perform the following steps to estblish Telnet connection to the P460 for configurtion: You need to ssign n outbnd interfce IP ddress using direct connection to the console seril port before you cn estblish the Telnet session. 1 Connect terminl to the RS-232 console port. 2 When you re prompted for Login Nme, enter the defult nme root. 3 When you re prompted for pssword, enter the pssword root. You re now in redwrite level.
4 At the prompt, type: set interfce outbnd <ip_ddr><net-msk> with n IP ddress nd netmsk to be used by the Avy P460 Supervisor module to connect vi its PPP interfce. The outbnd interfce should be on different subnet from the inbnd interfce. 5 Connect your sttion to the Fst Ethernet console port (directly or vi the network). Use UTP Ctegory 5 cble with n RJ45 connector. The mximum UTP cble length connected to the 10/100 Mbps port operting s 10/100BASE-T is 100 m (328 ft.). You cn obtin pproprite cbles from your locl supplier. 6 Verify tht you cn communicte with the P460 using ping to the outbnd interfce IP of the P460. If there is no response using the Ping commnd, check the IP ddress nd defult gtewy of both the P460 nd the sttion. 7 Strt Telnet session: From the Microsoft Windows tskbr of your PC click Strt nd then Run or ccess the commnd prompt Strt the Telnet session by typing: telnet <P460_IP_ddress> For exmple: telnet 149.49.35.214 The Login Nme prompt is displyed 8 Enter the defult nme root The pssword prompt is displyed 9 Enter the pssword root in lower cse letters. You cn now configure the P460. You cn connect the outbnd interfce to either of the supervisor module Fst Ethernet ports. Estblishing Telnet Connection with the Switch (Inbnd) Perform the following steps to estblish Telnet connection to the P460 for configurtion: You need to ssign n inbnd interfce IP ddress using direct connection to the console seril port before you cn estblish the Telnet session. 1 Connect terminl to the RS-232 console port. 2 When you re prompted for Login Nme, enter the defult nme root. 3 When you re prompted for pssword, enter the pssword root. You re now in redwrite level. At the prompt, type: set interfce outbnd <ip_ddr><net-msk> with n IP ddress nd netmsk to be used by the Avy P460 Supervisor module to connect vi its PPP interfce. 4 Connect your sttion to the I/O module (directly or vi the network). 5 Verify tht you cn communicte with the P460. Use the ping commnd to the inbnd interfce IP of the P460. If there is no response using the Ping commnd, check the IP ddress nd defult gtewy of both the P460 nd the sttion. The defult subnet msk is 255.255.255.0. 5
6 Strt Telnet session: From the Microsoft Windows tskbr of your PC click Strt nd then Run or ccess the commnd prompt Strt the Telnet session by typing: telnet <P460_IP_ddress> For exmple: telnet 149.49.35.214 The Login Nme prompt is displyed 7 Enter the defult nme root The pssword prompt is displyed 8 Enter the pssword root in lower cse letters. You cn now configure the P460. 5
Avy P460 Defult Settings We recommend tht you use the CLI to chnge defult prmeters. Refer to the Avy P460 documenttion for more informtion. Tble 12 Defult System Prmeters Prmeter Defult Vlue All IP ddresses N/A (0.0.0.0) CLI timeout 15 minutes User nme root Pssword root PPP interfce Disbled Outbnd interfce Disbled Inbnd interfce Disbled Inbnd ARP Tx intervl 5 seconds Outbnd ARP Tx intervl 5 seconds VLANs 1 on ll ports Spnning Tree Enbled Bridge priority for Spnning Tree 32,768 NTP server IP ddress N/A Time zone offset 0 hours Timezone GMT Red-only SNMP community string public Red-write SNMP community string public Trp SNMP community string public Number of SNMP retries 3 SNMP timeout 2,000 Intelligent multicst Disbled Boot bnk B Brodcst storm control Disbled 5
Run the Avy MSNM P460 Mnger (optionl) PC System Requirements for Running the Avy MSNM P460 Mnger Minimum hrdwre nd Operting System requirements re: Pentium II 400 Mhz-bsed computer with 128 Mb of RAM Screen resolution of 1024 x 768 pixels Microsoft Internet Explorer 5 or higher Microsoft Windows 2000 Worksttion or Windows XP Sun Microsystems Jv plug-in (supplied on the Documenttion nd Utilities CD) Refer to the Relese Notes for the exct version of the Jv plug-in Running the Avy MSNM P460 Mnger You should ssign n inbnd or out-of-bnd interfce IP ddress to the switch before beginning this procedure. 1 Open your browser. 2 Enter the URL of the switch in the formt http://.bbb.ccc.ddd where.bbb.ccc.ddd is the inbnd or outbnd interfce IP ddress of the switch. The user nme is root The defult psswords for red-write ccess is root. The P460 Mnger psswords re the sme s those of the CLI. If you chnge the psswords of the CLI then those psswords become ctive for Web mngement s well. For further informtion on the psswords, refer to the Avy P460 Instlltion nd Mintennce Guide The welcome pge is displyed. Figure 13 The Welcome Pge 6
If you hve the Jv plug-in instlled, the P460 Mnger opens in new window. See Figure 14 Figure 14 P460 Device Mnger If you do not hve the Jv plug-in instlled, follow the instructions on the Welcome pge tht offers vriety of options to instll the plug-in. You cnnot configure Lyer 3 prmeters if you run the P460 Device Mnger over the Outbnd interfce. 6
Avy Support Avy provides telephone number for you to use to report problems or to sk questions bout your contct center. The support telephone number is 1-800-242-2121 in the United Sttes. For dditionl support telephone numbers, see the Avy Web site: http://www.vy.com Select Support, then select Escltion Lists. This Web site includes telephone numbers for escltion within the United Sttes. For escltion telephone numbers outside the United Sttes, select Globl Escltion List. 2003 Avy Inc. All rights reserved. All trdemrks identified by the or TM re registered trdemrks or trdemrks, respectively, of Avy Inc. All other trdemrks re the property of their respective owners Ctlog No DO0722 Rev. 0. Februry 2003 vy.com