COMMUNICTIONS MODULES & SUBSYSTEMS RoHS-Compliant Small Form Factor 1x Press-Fit SFP Cage with Enhanced-Design Light Pipes PL-KP-1-000-8L Key Features Compatible with all MS-compliant SFP transceivers Staggered pins allow for PCB layouts in single and doublesided applications Enhanced EMI performance at datarates above 4Gbps RoHS-compliant and lead-free pplications Switch and hub devices Mass storage systems interconnect Host adapter cards Enterprise switch interconnects The unique lead-free and RoHS-Compliant, 1x pluggable press-fit cage with enhanced-design light pipes represents one of JDSU s complementary products to the Small Form Factor Pluggable (SFP) transceivers. Its patented design enables enhanced EMI performance using improved shielding between the cage and bezel. Optimized for use with all transceiver products complying with the SFP multisource agreement (MS), the cage design allows for low-cost implementation using standard manufacturing processes. Its hardened spring-tempered material, plus excellent material memory characteristics, provides for consistent transceiver mate/de-mate performance and enables port flexibility over the life of the system. The light pipes have been designed and improved so that their diameter will fit within host faceplate countersink features. The light pipes are more flexible and can more easily fit within openings on the faceplate. The back latch of the light pipe is designed for increased retention strength. Highlights Industry s most robust and sturdy cage design optimized for all SFP applications, including Fibre Channel, Gigabit Ethernet, and SONET Enhanced EMI performance for 4G applications due to improved mechanical shielding Supports all industry SFP transceivers, allows for board layouts and hole sizes for single and double sided applications Extensive compatibility testing with industry-wide MS-based modules for interoperability in multiple vendor implementations Backward compatible design offers superior mechanical stability, simplifying implementation to customer PCBs Tested for common applications and standard industry processes to allow seamless integration into manufacturing without additional equipment or requirements Excellent material memory characteristics provide for high cage retention to PCB, reducing field failures due to cage pull up NORTH MERIC: 800 498-JDSU (5378) WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com
ROHS-COMPLINT SMLL FORM FCTOR 1X PRESS-FIT Features RoHS-compliant and lead-free Superior EMI performance at 4Gbps Press-fit attachment 1x design enables high density applications Proven SFP transceiver cage Supports multiple system configurations Belly-to-belly or dual sided boards Robust manufacturing process Sturdy construction Hardened spring tempered alloy Simple assembly Utilizes common manufacturing equipment and processes 360 degree EMI contact fingers Low emission design FCC Class B compliant The PL-KP-1-000-8L 1x press-fit cage accommodates all MS-compliant SFP transceivers, and is ideally suited for application on printed circuit board (PCB) with a minimum thickness of.6mm (0.089 inches) for belly-to-belly applications. The excellent material memory characteristics provide high cage retention to the PCB, resulting in fewer field failures. Section 1 Functional Description The press-fit cage is designed based on the Small Form Factor Pluggable (SFP) Transceiver Multisource greement (MS).The PL-KP-1-000-8L may be used with the single-sided PCB layout, the double-sided PCB layout (called belly-tobelly), and the double-sided offset PCB layout. ll press-fit pins should be connected to chassis ground. double-sided PCB layout allows for one cage on the topside of the card and one on the bottom side that is directly under the topside cage (called belly-to-belly). The pins are staggered to avoid interference upon installation. The PCB must be a minimum of.6mm (0.089 inches) thick for Belly-to-Belly pplications. double-sided offset PCB layout allows for cages on both sides of the PCB, but staggered to allow more room for finger access between the units (offset belly-to-belly). The pins are staggered to avoid intereference upon installation. The PCB must be a minimum of.6mm (0.089 inches) thick for Offset Belly to Belly applications.
ROHS-COMPLINT SMLL FORM FCTOR 1X PRESS-FIT 3 Figure 1 1x press-fit cage mechanical drawing (PL-KP-1-000-8L) Section Installation Guide For best installation, a JDSU 66003473 press-fit tool should be used to install the cage. Care should be taken not to twist or tilt the cage during the installation process. Excessive force will result in damage to the unit. press machine similar to the MEP-6T/1T manufactured by utomated Services Group, West Palm Beach, FL is recommended for cage installation. Cage removal is very easy. Simply insert a flat metal bar or similar object into the cage assembly and lift it up off the PCB. ctual insertion and removal force may vary depending on plating material and finished hole size. Cages should not be reinstalled once they are removed from a board.
ROHS-COMPLINT SMLL FORM FCTOR 1X PRESS-FIT 4 Section 3 Recommended OEM PCB Layouts NOTES: 1 3 4 DTUM B TO BE ESTBLISHED BY CUSTOMER NOTED PDS ND VIS RE PLTED ND TIED TO CHSSIS GROUND. DIMENSIONS PPLY FTER PLTING. NOTED THRU HOLES RE UNPLTED. ELECTRICL PD LYOUT PER SFP MS. 4X 1.50 MX LED HEIGHTS 9X 0.95±0.05.33 X 7.13 X 11.93 4X 16.5 X 18.58 3.38 X 8.18 4X 1.55±0.05 3 X 0.85±0.05 6X 37.10 0.95 4X 30.90 X 30.00 7.50 3.50 MX X 0.00 0.95 37.80 MIN 35.00 3.50 0.95 5.00.80 15.00 X 10.00 5.00 0 4.50±0.10 1 B 1.00 MIN 0 10X 1.05±0.05 31.50 MIN COMPONENT ND TRCE KEEPOUT RE. LL EXPOSED METL SHOULD BE TIED TO CHSSIS GROUND. DIMENSIONS IN MILLIMETERS Figure Single sided board layout
ROHS-COMPLINT SMLL FORM FCTOR 1X PRESS-FIT 5 4X 3.50 SQ MX 0.50 M B 0 4.3 10.03 10.53 0.48 6.8 6.78 LED LOCTIONS, 4X 1.40 MIN TYP BCK PDS.00 MIN TYP 9.60 PLTED CHSSIS GROUND PDS ND VIS, TYP 4.10 TYP 4.10 TYP 1.00 MIN TYP COMPONENT KEEPOUT RE, TRCES OK 0.80 TYP 10.93 DETIL SCLE 6 : 1 4.00 MIN.00 SQ MIN TYP 7.18.00±0.05 TYP 0.10 L 4 0.50±0.05 TYP 0.06 B B DIMENSIONS IN MILLIMETERS Figure 3 Single sided detail layout 30.50 - - 3.65±0.10 0.0 16.5 4X.30±0.10 0.0 M 1.70±0.90 X 5.79 4X R1.00 MX 4X 0.50 X 45 4X 1.78 11.00 4X 1.78 0.40±0.10 11.00±0.10 3.50±0.10 SECTION - DIMENSIONS IN MILLIMETERS Figure 4 Front panel opening
ROHS-COMPLINT SMLL FORM FCTOR 1X PRESS-FIT Section 4 Package and Handling Instructions The PL-KP-1-000-8L is packaged in card board boxes. Each layer consists of 5 cages in plastic trays. There are 14 layers of trays for a total of 350 cages per box. Flammability The PL-KP-1-000-8L press-fit cage is made from lloy C77000 nickel-silver sheet metal with a nickel-plated BeCu EMI collar welded on. The polycarbonate light pipes are UL 94 V- rated. RoHS Compliance Compliant per the Directive 00/95/EC of the European Parliament and of the Council of 7 January 003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Ordering Information For more information on this or other products and their availability, please contact your local JDSU account manager or JDSU directly at 1-800-498-JDSU (5378) in North merica and +800-5378-JDSU worldwide or via e-mail at customer.service@jdsu.com. Sample: PL-KP-1-000-8L Part Number PL-KP-1-000-8L Description 1x (1 row x wide) EMI-Enhanced Press-Fit SFP Cage with Enhanced-Design Light Pipes NORTH MERIC: 800 498-JDSU (5378) WORLDWIDE: +800 5378-JDSU WEBSITE: www.jdsu.com Product specifications and descriptions in this document subject to change without notice. 010 JDS Uniphase Corporation 30168150 000 0610 PL-KP-1-000-8L.DS.CMS.E June 010