E-Vision Laser 4K Series High Brightness Digital Video Projector

E-Vision Laser 4K Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 118-157A

Abot This Docment Follow the instrctions in this manal careflly to ensre safe and long-lasting se of the projector. Symbols sed in this manal Many pages in this docment have a dedicated area for notes. The information in that area is accompanied by the following symbols: WARNING: this symbol indicates that there is a danger of physical injry to yorself and/or damage to the eqipment nless the instrctions are closely followed. ELECTRICAL WARNING: this symbol indicates that there is a danger of electrical shock nless the instrctions are closely followed. LASER WARNING: this symbol indicates that there is a potential hazard of eye exposre to laser radiation nless the instrctions are closely followed. NOTE: this symbol indicates that there is some important information that yo shold read. Prodct revision Becase we at Digital Projection continally strive to improve or prodcts, we may change specifications and designs, and add new featres withot prior notice. Updates may be available online - visit the Digital Projection website for all latest docments. Legal notice Trademarks and trade names mentioned in this docment remain the property of their respective owners. Digital Projection disclaims any proprietary interest in trademarks and trade names other than its own. Copyright 2017 Digital Projection Ltd. All rights reserved. page i

Introdction Congratlations on yor prchase of this Digital Projection prodct. Yor projector has the following key featres: Spport for Frame Seqential and Dal Pipe 3D formats. HDBaseT for transmission of ncompressed High Definition Video p to 100 m from the sorce. 3G-SDI with loop-throgh. Edge Blend. Blanking control for cstom inpt window sizing. Cornerstone, Vertical & Horizontal Keystone, Pincshion & Barrel, and Image Rotation. Separate control of screen and sorce aspect ratio. Control via LAN and RS232. Motorised lens mont. A serial nmber is located on the side of the projector. Record it here: page iii

CONTENTS INSTALLATION AND QUICK-START GUIDE...1 WHAT S IN THE BOX?... 3 CONNECTING THE POWER SUPPLY... 4 Voltage selection... 4 PROJECTOR OVERVIEW... 5 Front and rear views... 5 Control panel... 6 Projector indicators... 7 REMOTE CONTROL... 8 Infrared reception... 11 POSITIONING THE SCREEN AND PROJECTOR... 12 Roll and pitch... 13 CHANGING THE LENS... 14 Inserting a new lens... 14 Removing the lens... 14 CONNECTION GUIDE...19 SIGNAL INPUTS... 21 Digital inpts and otpts... 21 EDID on the DisplayPort, HDMI and HDBaseT inpts... 22 Using DisplayPort/HDMI/HDBaseT switchers with the projector... 22 3D connections... 23 Frame seqential 1080p and WUXGA 3D sorces at 100 and 120 Hz... 23 Dal Pipe 1080p, WUXGA and WQXGA 3D sorces at 100 and 120 Hz... 23 3D Sync... 24 3D Sync In... 24 3D Sync Ot... 24 3D Sync IR... 24 CONTROL CONNECTIONS... 25 LAN connection examples... 26 RS232 connection example... 27 OPERATING THE PROJECTOR... 15 Switching the projector on... 15 Switching the projector off... 15 Selecting an inpt signal... 16 Selecting a test pattern... 16 Adjsting the lens... 17 Adjsting the image... 17 page iv

CONTENTS (contined) OPERATING GUIDE...29 USING THE MENUS... 31 Opening the OSD... 31 Opening a men... 31 Exiting mens and closing the OSD... 31 Inside a men... 32 Accessing sb-mens... 32 Execting commands... 32 Editing projector settings... 33 Using a slider to set a vale... 33 Editing nmeric vales... 33 USING THE PROJECTOR... 34 Main men... 34 Lens men... 35 Lens Control... 35 Lens Memory... 36 Image men... 37 Color men... 38 Color Space... 38 Color Mode... 39 Geometry men... 44 Aspect Ratio... 44 Digital Zoom... 46 Overscan... 47 Blanking... 48 Keystone... 49 4 Corners... 51 Rotation... 52 Pincshion / Barrel... 53 Arc... 54 Edge Blend men... 55 Blend Width... 56 Black Level Uplift... 57 3D men... 58 3D types... 59 Some 3D settings explained... 60 Laser men... 61 Setp men... 62 ColorMax Setting... 64 Power On/Off... 65 Clock Adjst... 66 OSD Settings... 67 Memory... 67 Network men... 68 PIP men... 69 Information men... 70 Signal Format... 70 System Stats... 71 Thermal Stats... 71 Factory Reset... 72 SERVED WEB PAGES... 73 page v

CONTENTS (contined) REFERENCE GUIDE...81 THE DMD... 83 CHOOSING A LENS... 85 Basic calclation... 86 Basic calclation example... 87 Fll lens calclation... 88 Introdcing TRC... 88 Calclating TRC... 89 Calclating the throw ratio with TRC... 90 Fll lens calclation example... 91 APPENDIX C: WIRING DETAILS... 104 RS232... 104 Trigger 1 & Trigger 2... 105 Wired remote control... 105 Sync IN, Sync OUT and 3D Sync IR... 105 APPENDIX D: GLOSSARY OF TERMS... 106 POSITIONING THE SCREEN AND PROJECTOR... 92 POSITIONING THE IMAGE... 93 FRAME RATES AND PULLDOWNS EXPLAINED... 95 Interlaced and progressive scan... 95 Frame rates of image sorces... 95 Plldowns - conversion into destination formats... 96 2:3 (normal) plldown... 96 2:3:3:2 (advanced) plldown... 97 APPENDIX A: LENS PART NUMBERS... 98 APPENDIX B: SUPPORTED SIGNAL INPUT MODES... 99 2D formats... 99 SDI formats... 102 3D formats... 103 page vi

E-Vision Laser 4K Series High Brightness Digital Video Projector 4 INSTALLATION AND QUICK-START GUIDE

IN THIS GUIDE IN THIS GUIDE What s In The Box?... 3 Connecting The Power Spply... 4 Voltage selection...4 Projector Overview... 5 Front and rear views...5 Control panel...6 Projector indicators...7 Remote Control... 8 Infrared reception...11 Positioning The Screen And Projector... 12 Roll and pitch...13 Changing The Lens... 14 Inserting a new lens...14 Removing the lens...14 Operating The Projector... 15 Switching the projector on...15 Switching the projector off...15 Selecting an inpt signal...16 Selecting a test pattern...16 Adjsting the lens...17 Adjsting the image...17 Installation and Qick-Start Gide

WHAT S IN THE BOX? What s In The Box? MENU Pic Mte OPEN CLOSE OSD OFF ON OFF ON Make sre yor box contains everything listed. If any pieces are missing, contact yor dealer. OUT IN EXIT INFO FREEZE RE-SYNC FOCUS ZOOM SHIFT LENS OK DEFAULT Yo shold save the original box and packing materials, in case yo ever need to ship yor projector. HDMI1 HDMI3 IN USER PRESET HDMI2 DVI OUT 1 2 3 DisplayPort1 HD-T 3GSDI 4 5 6 R G B ALL VGA COMP1 COMP2 TEST 7 8 9 0 3D EYE PIP SWAP HDMI4 DisplayPort2 A B C D ADDR ALT ALT The projector is shipped withot a lens. Remote control 2x AAA batteries Secrity screw Projector Only one power cable - dependent on the destination territory - will be spplied with the projector. User Manal on disc Important Information HDMI cable Power cable, United Kingdom Power cable, Erope Power cable, North America Power cable, China Installation and Qick-Start Gide page 3

CONNECTING THE POWER SUPPLY Connecting The Power Spply Adjst the VOLTAGE SELECT switch 1 to the reqired voltage, then firmly psh the mains connector into the socket 2. Use only the power cable provided. Ensre that the power otlet incldes a grond connection as this eqipment MUST be earthed. 1 2 Handle the power cable careflly and avoid sharp bends. Do not se a damaged power cable. Voltage selection The VOLTAGE SELECT switch mst be set to match the power spply yo are sing: Voltage of power spply sed AC100-130V otlet Position of VOLTAGE SELECT switch AC200-240V (single phase) otlet Installation and Qick-Start Gide page 4

PROJECTOR OVERVIEW Projector Overview 1 2 3 Front and rear views 1 Air inlet 2 Front infrared window and indicators 3 Air inlet 4 Lens mont 5 Rear infrared window 4 Front view 5 6 7 8 6 Air otlet 7 Connections panel 8 Control panel 9 Adjstable feet 10 Voltage selector 11 Mains socket and switch 9 Rear view 10 11 12 Air inlets 12 Bottom view Installation and Qick-Start Gide page 5

Control panel 1 POWER Switches the projector on and off (STANDBY). 2 INPUT Switches to the next inpt sorce. 3 AUTO SYNC Re-synchronises with the crrent inpt signal. 4 ASPECT Changes the aspect ratio. 5 CENTER LENS Centers the lens. 6 PIC MUTE Shows and hides the projected image. When OFF, the light sorce is completely switched off and the screen is black. 7 MENU Displays and exits the OSD. 8 Arrow bttons & ENTER Navigation bttons sed to highlight men entries in the OSD. Press ENTER to open or execte the highlighted men entry. 9 EXIT Exits the crrent OSD page and enters the level above. 10 LENS SHIFT arrow bttons Each of these bttons moves the lens in the specified direction. 11 FOCUS pls and mins bttons Used to move the focs in and ot. 12 ZOOM pls and mins bttons Used to zoom in and ot. PROJECTOR OVERVIEW 1 2 3 4 5 6 POWER INPUT AUTO SYNC ASPECT CENTER LENS PIC MUTE 7 8 9 10 11 12 AUTO SYNC and ASPECT do not work when the projector ses HDMI 3 or 4. Installation and Qick-Start Gide page 6

PROJECTOR OVERVIEW Projector indicators TEMP. Off = no problem Flashing red = temperatre error LIGHT Off = light is switched off Flashing green = light is preparing to switch on Flashing red (cycles of six flashes) = light modle failre On, red = light modle has reached end of life On, green = light is switched on STATUS Off = no problem Flashing red (continosly) = cover error Flashing red (cycles of for flashes) = fan error On, red = system error TEMP. LIGHT STATUS POWER POWER Off = the projector is switched off Flashing green = the projector is warming p Flashing amber = the projector is cooling down On, red = STANDBY mode On, green = the projector is switched on Installation and Qick-Start Gide page 7

REMOTE CONTROL Remote Control 1 Power ON / OFF Trns power on and off. 2 Pic Mte OPEN / CLOSE Shows and hides the projected image. When OFF, the light sorce is completely switched off and the screen is black. 2 OSD ON / OFF Enable and disable screen timeot messages and control whether to show the OSD dring projection. 4 MENU Access the OSD. If the OSD is open, press this btton to go back to the previos men. 1 2 3 4 5 OFF MENU OPEN OFF Pic Mte OSD OK ON CLOSE ON DEFAULT 8 FREEZE and RE-SYNC are not available when the projector ses inpt HDMI 3 or 4. 3D is only available on the HDMI 3 and 4 inpts. This projector does not se the following options on the remote: DVI, VGA, COMP 1 and COMP 2. 5 Navigation (arrows and OK) Navigate throgh the mens with the arrows, confirm yor choice with OK. In lens adjstment modes, the arrows are sed to move, zoom or focs the lens. See 11 below. In lens adjstment modes, or when the OSD is not showing, the OK btton switches between modes: Shift Adjstment and Zoom / Focs Adjstment. 6 7 EXIT FREEZE INFO RE-SYNC 9 10 6 EXIT Go p one level in the OSD. When the top level is reached, press to close the OSD. 7 FREEZE Freeze the crrent frame. 8 DEFAULT When editing a parameter, press this btton to restore the defalt vale. 9 INFO Access information abot the projector. 10 RE-SYNC Re-synchronise with the crrent inpt signal. FOCUS IN OUT HDMI1 HDMI2 LENS SHIFT USER PRESET DVI 1 2 3 ZOOM IN OUT A B C D ALT HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI ADDR 4 5 6 ALT R G B ALL VGA COMP1 COMP2 TEST 7 8 9 0 3D EYE PIP SWAP contines on next page... Remote control Installation and Qick-Start Gide page 8

REMOTE CONTROL EXIT FREEZE INFO RE-SYNC 11 LENS adjstment FOCUS IN / OUT: adjst focs. SHIFT: press and hold this btton, then se the Navigation arrow bttons to move the lens. ZOOM IN / OUT: adjst zoom. 12 USER PRESET A, B, C, D Load ser presets. 13 ALT 11 FOCUS IN LENS SHIFT ZOOM IN 3D is only available on the HDMI 3 and 4 inpts. This projector does not se the following options on the remote: DVI, VGA, COMP 1 and COMP 2. Press and hold this btton to access alternative fnctions for all bttons with a green label. OUT OUT 14 DVI / DisplayPort2 / nmeric inpt 3 There is no DVI inpt on this projector. Use with ALT to select the DisplayPort 2 inpt. 12 USER PRESET A B C D 15 HDMI 2 / HDMI 4 / nmeric inpt 2 Select the HDMI 1 inpt. Use with ALT to select the HDMI 4 inpt. 16 HDMI 1 / HDMI 3 / nmeric inpt 1 Select the HDMI 1 inpt. Use with ALT to select the HDMI 3 inpt. 17 TEST / SWAP / nmeric inpt 0 Show a test pattern. Press again to show the next test pattern:...off, White, Black, Red, Green, Ble, CheckerBoard, CrossHatch, V Brst, H Brst, ColorBar... When PIP mode is on, se this btton with ALT to swap the main and sb images. HDMI1 HDMI2 DVI 1 2 3 HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI 4 5 6 ALT ALT ADDR R G B ALL VGA COMP1 COMP2 TEST 7 8 9 0 3D EYE PIP SWAP 13 14 15 16 17 contines on next page... Remote control Installation and Qick-Start Gide page 9

REMOTE CONTROL 17 DISPLAYPORT 1 / R / nmeric inpt 4 Select DisplayPort 1 inpt. 18 HD-T / G / nmeric inpt 5 Select the HDBaseT inpt. OFF ON PIP is not available when the projector ses inpt HDMI 3 or 4. 19 3GSDI / B / nmeric inpt 6 Select the 3G-SDI inpt. 20 VGA / 3D / nmeric inpt 7 There is no VGA inpt on this projector. Use with ALT to toggle the 3D Format setting between Off and Ato. 21 COMP1 / EYE / nmeric inpt 8 There is no Component 1 inpt on this projector. Use with ALT to switch between left and right eye 3D dominance. 22 COMP2 / PIP / nmeric inpt 9 There is no Component 2 inpt on this projector. Use with ALT to switch on Pictre In Pictre (PIP) mode. FOCUS IN OUT Pic Mte OPEN CLOSE OSD Remote control top OFF LENS SHIFT ON ZOOM IN OUT 3D is only available on the HDMI 3 and 4 inpts. This projector does not se the following options on the remote: DVI, VGA, COMP 1 and COMP 2. 23 ADDR / ALL (with red indicator at the top) Assign and nassign an IR remote address. To assign an address: 1. Press and hold this btton ntil the indicator starts flashing. 2. Release this btton and while the indicator is still flashing, enter a two-digit address sing the nmeric inpt bttons. The indicator will flash three times qickly to confirm the change. To nassign an address and retrn to the defalt address 00, Press and hold ALT and this btton simltaneosly ntil the indicator flashes to confirm the change. 17 18 19 20 A B C D HDMI1 USER PRESET HDMI2 DVI 1 2 3 4 5 6 ALT ALT HDMI3 HDMI4 DisplayPort2 DisplayPort1 HD-T 3GSDI ADDR R G B ALL VGA COMP1 COMP2 TEST 7 8 9 0 3D EYE PIP SWAP 23 21 22 Remote control bottom Installation and Qick-Start Gide page 10

REMOTE CONTROL Infrared reception The projector has infrared sensors at the front and back. The angle of acceptance is 40. Make sre that the remote control is within the angle of acceptance when trying to control the projector. 40 40 Infrared reception Installation and Qick-Start Gide page 11

POSITIONING THE SCREEN AND PROJECTOR Positioning The Screen And Projector 1. Install the screen, ensring that it is in the best position for viewing by yor adience. 2. Mont the projector, ensring that it is at a sitable distance from the screen for the image to fill the screen. Set the adjstable feet so that the projector is level, and perpendiclar to the screen. The drawing below shows the positions of the feet for table monting, and the fixing holes for ceiling monting. 1 For adjstable feet Always allow the projector to cool for 5 mintes before disconnecting the power or moving the projector. 2 Six M4 holes for ceiling mont The screws shold not penetrate more than 15 mm into the body of the projector. 1 1 Ensre that there is at least 50 cm (19.7 in) of space between the ventilation otlets and any wall, and 30 cm (11.8 in) on all other sides. 2 2 2 2 2 2 1 1 Installation and Qick-Start Gide page 12

POSITIONING THE SCREEN AND PROJECTOR Roll and pitch The projector can be operated in nmeros positions. In portrait mode, it is recommended to position the projector with inpts facing pward, as shown in the diagram. 30 1 360 2 330 2 Roll Pitch 1 Recommended positions: inpts side p 2 Also possible Installation and Qick-Start Gide page 13

CHANGING THE LENS Changing The Lens Inserting a new lens 1. Remove the front and rear lens caps. Before changing the lens, always make sre the projector is switched off and flly disconnected from its power spply. When changing the lens, avoid sing excessive force as this may damage the eqipment. 2. Position the lens so that the labels are at the top, and gently insert it all the way into the lens mont. 3. Psh the lens in firmly and trn it clockwise ntil it clicks into place. The lens is shipped separately. Take care to preserve the original lens packaging and protective caps for ftre se. Removing the lens The projector will not power on withot the lens fitted. 1. Psh in the lens release lever, and trn the lens anti-clockwise. 2. Remove the lens. Installation and Qick-Start Gide page 14

OPERATING THE PROJECTOR Operating The Projector Switching the projector on 1. Ensre a lens is fitted. Connect the power cable between the mains spply and the projector. (See Connecting the power spply above.) Switch on at the switch next to the power connector. 2. The POWER indicator lights red to signal that the projector is in STANDBY mode. Press one of the following bttons: On the remote control, the ON btton On the projector control panel, the POWER btton. The fans begin working, then the POWER indicator begins flashing green. When the flashing stops, the POWER and LIGHT indicators both light steady green. The projector is switched on. See also Connecting The Power Spply earlier in this gide. The self-test is rnning when all the LEDs on the control panel are lit. Use only the power cable provided. Switching the projector off 1. Press OFF on the remote control or POWER on the control panel, then press again to confirm yor choice. The POWER indicator on the control panel will start flashing amber, the system will go ot and the cooling fans will rn for a short time ntil the POWER indicator goes steady red to indicate that the projector has entered STANDBY mode. 2. If yo need to switch the projector off completely, switch off at the mains power switch next to the power connector and then disconnect the power cable from the projector. Ensre that the power otlet incldes a grond connection as this eqipment MUST be earthed. Handle the power cable careflly and avoid sharp bends. Do not se a damaged power cable. Installation and Qick-Start Gide page 15

OPERATING THE PROJECTOR Selecting an inpt signal 1. Connect one or more image sorces to the projector. 2. Select the inpt yo want to display: Press one of the inpt bttons on the remote control. Alternatively, open the On-screen display (OSD) by pressing MENU. Highlight Inpt from the main men, press ENTER/OK and then select an inpt signal sing the UP and DOWN arrow bttons. Press ENTER/OK to confirm yor choice. For fll details of how to se the controls and the men system, see the Operating Gide. Selecting a test pattern To display a test pattern: Press TEST on the remote control. Change the test pattern sing the LEFT and RIGHT arrow bttons. Test patterns are displayed in the following order: White, Black, Red, Green, Ble, Cyan, Yellow, Magenta, Off Alternatively, open the OSD by pressing MENU. Highlight Test Patterns from the main men, then select a test pattern sing the LEFT and RIGHT arrow bttons. After the final test pattern, the projector exits test pattern mode and retrns to the main image. To view test patterns again, yo need to press TEST again. If yo wish to exit the test patterns before yo reach the final one, press TEST or EXIT at any time. Installation and Qick-Start Gide page 16

OPERATING THE PROJECTOR Adjsting the lens The lens can be adjsted sing the Lens men, or sing the lens bttons on the remote control. Lens men The Lens men provides access to the Lens Control setting and the Lens Center command. Lens Control allows Zoom, Focs and Shift adjstment sing the arrow bttons. The setting operates in Zoom/Focs Adjstment and Shift Adjstment mode. Press ENTER/SELECT to switch between the two modes. Remote control Use the remote control to adjst zoom, focs and shift directly, withot opening a men: OK enters lens control, then switches between Zoom/Focs Adjstment and Shift Adjstment. EXIT exits lens control and opens the Lens men. MENU exits lens control and retrns to the main image. The arrow bttons adjst zoom, focs and shift as indicated on the screen. For fll details of how to adjst the lens sing the remote control, see Remote Control earlier in this gide. Adjsting the image Orientation This can be set from the Setp men. Setp men Highlight Orientation and choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Ato-front. Geometry Settings sch as Keystone, Rotation, Pincshion / Barrel and Arc can be set from the Geometry men. Pictre Settings sch as Gamma, Brightness, Contrast, Satration, He and Sharpness can be set from the Image men. Geometry men Image men Neither of the settings nder Pictre are available with the HDMI 3 and 4 inpts. Installation and Qick-Start Gide page 17

E-Vision Laser 4K Series High Brightness Digital Video Projector 4 CONNECTION GUIDE

IN THIS GUIDE IN THIS GUIDE Signal Inpts... 21 Digital inpts and otpts...21 EDID on the DisplayPort, HDMI and HDBaseT inpts...22 Using DisplayPort/HDMI/HDBaseT switchers with the projector...22 3D connections...23 Frame seqential 1080p and WUXGA 3D sorces at 100 and 120 Hz...23 Dal Pipe 1080p, WUXGA and WQXGA 3D sorces at 100 and 120 Hz...23 3D Sync...24 3D Sync In...24 3D Sync Ot...24 3D Sync IR...24 Control Connections... 25 LAN connection examples...26 RS232 connection example...27 Connection Gide

SIGNAL INPUTS Signal Inpts Digital inpts and otpts 1 HDBaseT Receives digital signal from HDBaseT-compliant devices. 2 3G-SDI in 3 3G-SDI ot Connect a 3G-SDI cable to distribte the 3G-SDI signal to another projector. For simltaneos HDBaseT and LAN connectivity, a third-party distribtion prodct can be tilised to combine HDBaseT video stream with LAN connection for delivery to the projector. 4 HDMI 1 / HDMI 2 / HDMI 3 / HDMI 4 HDMI 1 and 2 are HDMI 2.0 inpts spporting HDCP 2.2. HDMI 3 and 4 are HDMI 1.4b inpts spporting Frame Seqential and Dal Pipe 3D with HDCP 1.4. Connect an HDMI cable to the connector. 5 DisplayPort DisplayPort 1.2 inpt. Connect a DisplayPort cable to the connector. Spports sorces p to 1920x1200 resoltion, 24-120 Hz. Spports HDCP 2.2. (1) (2) RS232 TRIGGER WIRED REMOTE HDBaseT/LAN Ethernet HDMI 1 HDMI 2 DisplayPort 3D SYNC IR SDI IN SDI OUT HDMI 3 HDMI 4 SYNC IN SYNC OUT 1 2 3 4 5 Connection Gide page 21

SIGNAL INPUTS EDID on the DisplayPort, HDMI and HDBaseT inpts If yo are sing a compter graphics card or another sorce that obeys the EDID protocol, the sorce will atomatically configre itself to sit the projector. Otherwise refer to the docmentation spplied with the sorce to manally set the resoltion to the DMD resoltion of the projector or the nearest sitable setting. Switch off the sorce, connect to the projector, then switch the sorce back on again. Using DisplayPort/HDMI/HDBaseT switchers with the projector When sing a DisplayPort/HDMI/HDBaseT sorce switcher with the projector, it is important to set the switcher so that it passes the projector EDID throgh to the sorce devices. If this is not done, the projector may not be able to lock to the sorce or display the sorce correctly as its video otpt timings may not be compatible with those of the projector. Sometimes this is called transparent, pass-throgh or clone mode. See yor switcher s manal for information on how to set this mode. 1 Sorces 1 2 3 2 Switcher 3 Projector EDID EDID EDID EDID The EDIDs in the switcher shold be the same as the one in the projector. Connection Gide page 22

SIGNAL INPUTS 3D connections Frame seqential 1080p and WUXGA 3D sorces at 100 and 120 Hz 1. Connect to HDMI 3 or 4. 2. Set 3D Format in the 3D men to Frame Seqential. Dal Pipe 1080p, WUXGA and WQXGA 3D sorces at 100 and 120 Hz 1. Connect the left eye otpt to the HDMI 3 socket and the right eye otpt to the HDMI 4 socket. 2. Set 3D Format in the 3D men to Dal-Pipe. See 3D formats in the Reference Gide for a complete list of spported formats and frame rates. While the projector can receive 100/120Hz and display 3D at 100/120Hz, video processing is limited to 60Hz. This also applies to Dal Pipe 3D at 60 Hz per inpt. (1) (2) RS232 TRIGGER WIRED REMOTE HDBaseT/LAN Ethernet HDMI 1 HDMI 2 DisplayPort 3D SYNC IR SDI IN SDI OUT HDMI 3 HDMI 4 SYNC IN SYNC OUT 1 2 3 4 1 HDBaseT 2 HDMI 1 / Dal Pipe Left 3 DVI 4 HDMI 2 / Dal Pipe RIGHT Connection Gide page 23

SIGNAL INPUTS 3D Sync 3D Sync In Sync inpt signal. Connect the 3D sync from yor graphics card or server. 3D Sync Ot Sync otpt signal. Enables 3D from mltiple projectors. 3D Sync IR Sync otpt signal. This may be affected by the 3D Sync Offset setting in the 3D men. Connect this to yor IR emitter or ZScreen. (1) (2) RS232 TRIGGER WIRED REMOTE HDBaseT/LAN Ethernet HDMI 1 HDMI 2 DisplayPort 3D SYNC IR SDI IN SDI OUT HDMI 3 HDMI 4 1 3D Sync IR SYNC IN SYNC OUT 2 Sync In 1 2 3 3 Sync Ot 4 5 6 4 3D inpt 5 3D Sync In 6 3D Sync IR 7 7 IR emitter or ZScreen Connection Gide page 24

CONTROL CONNECTIONS Control Connections 1 HDBaseT/LAN The projector s featres can be controlled via a LAN connection, sing Digital Projection s Projector Controller application or a terminal-emlation program. 2 Ethernet This dedicated LAN connection can be sed if HDBaseT/LAN is already being sed for HDBaseT signal inpt. 3 Trigger 1 & Trigger 2 The Trigger otpts are activated by one of the three following conditions, as set in the Setp men: Screen trigger: can be connected to an electrically operated screen, atomatically deploying the screen when the projector starts p, and retracting the screen when the projector shts down. Aspect ratio trigger: can be sed to control screen shttering for different aspect ratios. RS232 trigger: can be sed to control the screen or screen shttering on receipt of an RS232 command 4 RS232 All of the projector s featres can be controlled via a serial connection, sing commands described in the Protocol Gide. Use a straight-throgh cable to connect directly to a compter. 5 Wired Remote The remote control can be connected sing a standard 3.5 mm mini jack cable (tip-ring-sleeve, or TRS). 1 2 3 4 5 For a list of all commands sed to control the projector via LAN, see the Protocol Gide. Only one remote connection (RS232 or LAN) shold be sed at any one time. With a LAN connection the projector can serve a web page offering basic projector controls. Trigger 1 and Trigger 2 are not available with HDMI 3 and 4 inpts. Projector Controller is available for download, free of charge, from the Digital Projection website. (1) (2) RS232 TRIGGER WIRED REMOTE HDBaseT/LAN Ethernet HDMI 1 HDMI 2 DisplayPort 3D SYNC IR SDI IN SDI OUT HDMI 3 HDMI 4 SYNC IN SYNC OUT Connection Gide page 25

CONTROL CONNECTIONS LAN connection examples The projector s featres can be controlled via a LAN connection, sing Digital Projection s Projector Controller application or a terminalemlation program With a LAN connection the projector can serve a web page offering basic projector controls. Compter Un-crossed LAN cable Projector Projector Controller is available for download, free of charge, from the Digital Projection website. For simltaneos HDBaseT and LAN connectivity, a third-party distribtion prodct can be tilised to combine HDBaseT video stream with LAN connection for delivery to the projector. Un-crossed LAN cables Compter Hb or LAN HDBaseT/LAN Ethernet Projector SDI IN SDI Projector 1 1 LAN Connection Gide page 26

CONTROL CONNECTIONS RS232 connection example All of the projector s featres can be controlled via a serial connection, sing commands described in the Protocol Gide. The Protocol Gide is available separately. Straightthrogh cable Compter Projector 1 (1) (2) RS232 TRIGGER WIRED REMOTE HDBaseT/LAN Ethernet HDMI 1 HDMI 2 DisplayPort 3D SYNC IR SDI IN SDI OUT HDMI 3 HDMI 4 SYNC IN SYNC OUT 1 RS232 Connection Gide page 27

E-Vision Laser 4K Series High Brightness Digital Video Projector 4 OPERATING GUIDE

IN THIS GUIDE IN THIS GUIDE Using The Mens... 31 Opening the OSD...31 Opening a men...31 Exiting mens and closing the OSD...31 Inside a men...32 Accessing sb-mens...32 Execting commands...32 Editing projector settings...33 Using a slider to set a vale...33 Editing nmeric vales...33 Using The Projector... 34 Main men...34 Lens men...35 Lens Control...35 Lens Memory...36 Image men...37 Color men...38 Color Space...38 Color Mode...39 Geometry men...44 Aspect Ratio...44 Digital Zoom...46 Overscan...47 Blanking...48 Keystone...49 4 Corners...51 Rotation...52 Pincshion / Barrel...53 Arc...54 Edge Blend men...55 Blend Width...56 Black Level Uplift...57 3D men...58 3D types...59 Some 3D settings explained...60 Laser men...61 Setp men...62 ColorMax Setting...64 Power On/Off...65 Clock Adjst...66 OSD Settings...67 Memory...67 Network men...68 PIP men...69 Information men...70 Signal Format...70 System Stats...71 Thermal Stats...71 Factory Reset...72 Served Web Pages... 73 Operating Gide

USING THE MENUS Using The Mens Opening the OSD OFF ON Access the varios mens sing either the projector control panel or the remote control. On either device, press the MENU btton. OFF Pic Mte OSD ON The on-screen display (OSD) opens showing the list of available mens. POWER INPUT AUTO SYNC ASPECT CENTER LENS PIC MUTE OFF MENU ON DEFAULT Opening a men Move p and down the list sing the UP and DOWN arrow bttons. To open a men, press ENTER on the control panel or OK on the remote control. This gide refers to the above two bttons as ENTER/OK. Projector control panel Main Men OK EXIT INFO FREEZE RE-SYNC Remote control Main Men Inpt HDMI 1 p Exiting mens and closing the OSD Test Pattern Lens PIP Information To go back to the previos page, press EXIT. Image Color When yo reach the top level, pressing EXIT will close the OSD. Geometry Edge Blend To close the OSD from any page, press MENU. 3D Laser Setp Network q On-screen display (OSD): top level mens Operating Gide page 31

Inside a men When yo open a men, the page consists of the following elements: Title bar at the top Shows which men yo have accessed. Highlighted item Available and navailable items Unavailable items appear a pale gray color. Whether an item is available may depend on other settings. The text or symbol to the right of an item shows whether the item: has a vale that can be changed (the crrent vale is shown) opens a sb-men (an arrow btton is displayed) exectes a command (the space to the right of the item is blank). USING THE MENUS Highlighted Item Men Item Unavailable Item Slider Sb-men Command Men Name Vale Vale Vale Vale The highlighted item has green backgrond. Accessing sb-mens Use the UP and DOWN arrow bttons to highlight the sb-men, then press ENTER/OK. Execting commands If the item contains a command, highlighting it reveals an OK btton. Press ENTER/OK to execte the highlighted command. Inside a men Men Name Men Item Vale Highlighted Command Highlighted command OK Yo may be asked for confirmation. Use the ENTER/OK to confirm, or EXIT to cancel. Command Name WARNING All [Men] vales will be lost. Press OK to confirm Press Exit to cancel Confirmation dialog Operating Gide page 32

Editing projector settings If the highlighted men item contains a list of vales to choose from, yo can change the vale by doing the following: 1. Highlight the men item and press ENTER/OK. 2. In the list of vales that opens, se the UP and DOWN arrow bttons to highlight a vale, then press ENTER/OK again to select the highlighted vale. USING THE MENUS Highlighted Item Men Item Men Item Men Name Crrent Vale Highlighted Vale Vale Vale Vale Some men items may be navailable de to settings in other mens. Unavailable men items appear gray. Using a slider to set a vale Some parameters open a slider. To set sch a parameter: 1. Press the LEFT or RIGHT arrow btton, or ENTER/OK. The arrow bttons will open the slider and adjst the vale at the same time. ENTER/OK will open the slider withot altering the initial vale. 2. Use the LEFT and RIGHT arrow bttons to move the slider. 3. When ready, press EXIT to exit the slider and retrn to the men, or press MENU to exit the slider withot showing the men again. Parameter List of vales Vale Slider Editing nmeric vales Some parameters take nmeric vales withot sing sliders - for example, color matching vales or IP addresses. 1. Use the UP and DOWN arrow bttons to highlight the row containing the nmeric field yo wish to edit. 2. Press ENTER/OK to enter edit mode. A nmeric field in edit mode is white text on ble backgrond. 3. In edit mode: Use the UP arrow btton to increase the nmeric vale. Use the DOWN arrow btton to decrease the nmeric vale. 4. Use the LEFT and RIGHT arrow bttons to edit the next or previos nmeric fields within the same row. 5. Once ready, press ENTER/OK to exit edit mode. Data Row x: 0.658 y: 0.339 Highlighted Row x: 0.315 y: 0.662 Row x: 0.146 y: 0.043 Row x: 0.276 y: 0.283 Nmeric vales Operating Gide page 33

USING THE PROJECTOR Using The Projector Main Men Main men Inpt Press ENTER/OK to open the list of available inpts. Use the UP and DOWN arrow bttons to select an inpt from the list, then press ENTER/OK to confirm yor choice. Inpt Test Pattern Lens Image Color HDMI 1 See Signal Inpts in the Connection Gide for frther information abot the available inpts and connections. Press EXIT to retrn to the main men. Test Pattern Choose from:...off, White, Black, Red, Green, Ble, Cyan, Yellow, Magenta... Use the LEFT and RIGHT arrow bttons to switch between vales. Lens, Image, Color, Geometry, Edge Blend, 3D, Laser, Setp and Network Press ENTER/OK to open these mens and access varios settings. Geometry Edge Blend 3D Laser Setp Network q Selecting a test pattern hides the OSD. Press EXIT to hide the test pattern, and then press MENU to show the OSD. Press the DOWN arrow at the bottom of the page to access additional mens: Main Men PIP and Information Press ENTER/OK to open these mens and access varios settings. PIP p Press the UP arrow to retrn to the previos page. Information Main men, page 1 and 2 Operating Gide page 34

USING THE PROJECTOR Lens men Lens Lock When this featre is On, all other Lens men items are disabled. Lens Control Opens a sb-men, see below. Center Lens Centers the lens. Lens Type Lens Lock Lens Control Center Lens Lens Type Lens Memory Lens Off non-ust Lens Choose a UST or a non-ust lens. Lens Memory Opens a sb-men, see next page. Lens Control Lens Control settings operate in Zoom/Focs Adjstment and Shift Adjstment mode. Press ENTER/OK to switch between modes. When in Zoom/Focs Adjstment mode: Use the UP and DOWN arrow bttons to adjst Zoom. Use the LEFT and RIGHT arrow bttons to adjst Focs. When in Shift Adjstment mode, se the arrow bttons to adjst Shift. Zoom Focs Lens Control p t [Enter] Shift Adjstment Lens Control p t Shift q [Enter] Zoom / Focs Adjstment q Operating Gide page 35

USING THE PROJECTOR Lens men contined from previos page Lens Memory This men allows yo to load, save and delete p to ten lens presets, containing position, zoom, focs and shift adjstment information. For example, if sing different screen sizes and aspect ratios, yo can save zoom, focs and positioning for each screen size and aspect ratio in a dedicated preset. Use Clear Memory to delete a memory preset if yo need to save a new combination of lens settings in its place. Overwriting a saved memory preset is not possible. Load Memory Save Memory Clear Memory Lens Memory Lens Load Memory Lens Save Memory Lens Clear Memory Memory 1 OK Memory 1 OK Memory 1 OK Memory 2 Memory 2 Memory 2 Memory 3 Memory 3 Memory 3 Memory 4 Memory 4 Memory 4 Memory 5 Memory 5 Memory 5 Memory 6 Memory 6 Memory 6 Memory 7 Memory 7 Memory 7 Memory 8 Memory 8 Memory 8 Memory 9 Memory 9 Memory 9 Memory 10 Memory 10 Memory 10 Operating Gide page 36

Image men Pictre Mode Choose from High Bright, Presentation and Video. Use a different setting depending the type of inpt sorce. Press ENTER/SELECT to open the list. Use the UP and DOWN arrow bttons to select a pictre mode from the list, then press ENTER/OK to confirm yor choice. Press EXIT to retrn to the main men. Dynamic Black Set to On to allow for increased contrast in darker scenes by modlating the light sorce. Smooth Pictre When this featre is On, the projector is able to display lower resoltion sorces in 4K UHD resoltion. Sorces will be displayed within WQXGA+ if Smooth Pictre is Off. Ato will allow the projector to decide based pon the bandwidth of incoming sorces. Gamma Choose a de-gamma crve from 1.0, 1.8, 2.0, 2.2, 2.35, 2.5, S-Crve and DICOM. Used correctly, the Gamma setting can improve contrast while maintaining good details for blacks and whites. If excess ambient light washes ot the image and it is difficlt to see details in dark areas, lower the Gamma setting to compensate. This improves contrast while maintaining good details for blacks. Conversely, if the image is washed ot and nnatral, with excessive detail in black areas, increase the setting. S-Crve is an enhanced mid-tone gamma. DICOM is a simlated DICOM display, which can be sed for training applications. Brightness, Contrast, Satration, He, Sharpness Highlight the setting yo wish to edit, and then press ENTER/OK, or the LEFT or RIGHT Operating Gide arrow btton to open the slider. Use the LEFT and RIGHT arrow bttons to adjst the slider. Press EXIT to close the slider and retrn to the men, or MENU to close the slider and retrn to the projected image. Noise Redction Choose a level of noise redction from Off, Low, Middle and High. Freeze Freezes the crrent frame. Resync Press ENTER/OK to force the projector to resynchronise with the crrent inpt. USING THE PROJECTOR Pictre Mode Dynamic Black Smooth Pictre Gamma Brightness Contrast Satration He Sharpness Noise Redction Freeze Resync Image 100 100 100 100 10 Brightness 100 High Bright Off Ato 2.2 Off The following settings are not available with inpt HDMI 3 or HDMI 4: Smooth Pictre Brightness, Contrast, Satration, He, Sharpness Noise Redction The Freeze and Resync fnctions will also be navailable. page 37

USING THE PROJECTOR Color men Color Color Space In most cases, the Ato setting determines the correct colorspace to se. If it does not, yo can choose a specific colorspace: Choose from Ato, YPbPr, YCbCr, RGB PC and RGB Video. Color Space Color Mode ColorMax Manal Color Matching Color Temperatre Ato ColorMax Peak Native Color Space is not available with HDMI 3 or HDMI 4. Gains and Lifts Color Color Space Ato Color Mode ColorMax Manal Color Matching Color Temperatre Gains and Lifts Ato ColorMax Native YPbPr Peak Ato 100 YCbCr 100 RGB Native PC 100 RGB Video Operating Gide page 38

USING THE PROJECTOR Color Mode The projector can work in the following color modes: ColorMax, Manal Color Matching, Color Temperatre and Gains and Lifts. Color Color Space Ato Color Mode ColorMax ColorMax ColorMax Manal Color Matching Manal Color Matching Color Temperatre Color Temperatre Gains and Lifts Gains and Lifts Only one color mode can be selected at a time. Settings sed by the other color modes are disabled. ColorMax 1. Set Color Mode to ColorMax. 2. Navigate to the ColorMax setting. Choose from HDTV, Peak, User 1 and User 2. User 1 and User 2 are ser-defined color gamts set via the Setp > ColorMax men. See Setp men for frther information abot setting p the User 1 and User 2 color gamts. Operating Gide page 39

USING THE PROJECTOR Color men contined from previos page Manal Color Matching 1. Set Color Mode to Manal Color Matching. Manal Color Matching Ato Test Pattern Off 2. Open the Manal Color Matching sbmen. Red Green Here yo can do the following: Switch Ato Test Pattern On and Off. Adjst He, Satration and Gain settings for each individal color to improve the color balance of the projected image. Adjst white balance RGB vales. Reset all vales. Ble Yellow Cyan Magenta White Balance Reset Color For more details abot the He, Satration and Gain settings, see Color matching parameters explained frther in this gide. Manal Color Matching Red He 100 Satration 100 Gain 100 Color Space Manal Color Matching White Color Mode Red ColorMax Green Manal Color Matching Ble Color Temperatre Gains and Lifts Ato ColorMax 100 Peak 100 HDTV 100 Peak User 1 User 2 Operating Gide page 40

USING THE PROJECTOR Color men contined from previos page Color matching parameters explained The levels of he, satration and gain in the Manal Color Matching men change the color vales in the following ways: 1 2 3 1 He Specifies the position of each color (red, yellow, green, cyan, ble and magenta) relative to its neighboring colors. MAGENTA RED YELLOW RED 2 Satration Specifies the level of white in each color (i.e. how pale each color is). 3 Gain Controls the amont of light that goes into each color, i.e. the lowest gain wold prodce black. WHITE BLUE GREEN BLACK CYAN Operating Gide page 41

USING THE PROJECTOR Color men contined from previos page Color Temperatre 1. Set Color Mode to Color Temperatre. 2. Navigate to the Color Temperatre setting. Choose a vale from 3200K (warmer) to 9300K (cooler) or Native (no correction). Color Color Space Color Mode ColorMax Manal Color Matching Color Temperatre Gains and Lifts Ato Color Temperatre Peak Native 3200K 5400K 6500K 7500K 9300K Native Operating Gide page 42

USING THE PROJECTOR Color men contined from previos page Gains and Lifts Lifts allow yo to adjst black levels of individal colors, while gains adjst the bright part of the scale. Set the sliders as reqired. Red Lift Green Lift Ble Lift Red Gain Green Gain Ble Gain Reset Gains and Lifts 100 100 100 100 100 100 Operating Gide page 43

USING THE PROJECTOR Geometry men Geometry This men allows yo to compensate for image distortions cased by an nsal projection angle or irreglar screen srface. Aspect Ratio Digital Zoom Overscan Blanking Sorce Off Aspect Ratio, Digital Zoom and Overscan are not available with inpt HDMI 3 or HDMI 4. Keystone 4 Corners Rotation Pincshion / Barrel Arc Aspect Ratio This featre defines the aspect ratio of the sorce. Use the Setp > Screen Setting to define the screen aspect ratio. If yo choose a preset aspect ratio from here, it will give yo the best fit for yor selection. Choose from: 5:4 4:3 16:10 16:9 1.88 2.35 TheaterScope Sorce Unscaled Image scaling and aspect ratio are also inflenced by Setp > Screen Setting. See next page for frther information abot the TheaterScope aspect ratio. Operating Gide page 44

USING THE PROJECTOR Theaterscope setting The TheaterScope setting is sed in combination with an anamorphic lens to restore 2.35:1 images packed into a 16:9 frame. Sch images are projected with black lines at the top and bottom of the 16:9 screen to make p for the difference in aspect ratios. Withot an anamorphic lens and withot the TheaterScope setting applied, a 16:9 sorce containing a 2.35:1 image looks like this: Black margin part of the sorce TheaterScope is sed with an anamorphic lens. If yo se TheaterScope, set yor screen aspect ratio to 16:9. Black margin part of the sorce If we change the setting to TheaterScope, the black lines will disappear bt the image will stretch vertically to reach the top and bottom of the DMD : An anamorphic lens will stretch the image horizontally, restoring the original 2.35 ratio: Operating Gide page 45

USING THE PROJECTOR.Geometry men contined from previos page Digital Zoom Digital zooming enlarges a section of the image, while the area otside the enlarged section is cropped ot to preserve the overall image size. Digital Zoom defines the level of zoom that needs to be applied. If Digital Zoom is set to 0, then the other settings in the men will be disabled. Digital Pan and Digital Scan specify the area that is being enlarged: Digital Pan adjsts the horizontal coordinates. Digital Scan adjsts the vertical coordinates. The Reset command restores the defalt Digital Zoom, Digital Pan and Digital Scan vales. Digital Zoom Digital Pan Digital Scan Reset Digital Zoom 0 0 0 Operating Gide page 46

USING THE PROJECTOR Geometry men contined from previos page Overscan Use this setting to compensate for noisy or badly defined image edges. Crop removes nwanted artifacts from the edges of yor image by cropping the edges. Zoom increases the size of the image to force the edges off-screen. Geometry Aspect Ratio Sorce Digital Zoom Overscan Off Blanking Off Keystone Crop 4 Corners Zoom Rotation Pincshion / Barrel Arc Image with noisy edges Overscanned image Operating Gide page 47

USING THE PROJECTOR Geometry men contined from previos page Blanking Use this featre to: fit an odd-sized screen; ct off timecode dots in the top line of a pictre; ct off sbtitles, etc. Select the edge yo wish to blank and se the LEFT and RIGHT arrow bttons to determine the amont of correction. Use the Reset command to restore blanked edges. Top Bottom Left Right Reset Blanking 0 0 0 0 Operating Gide page 48

USING THE PROJECTOR Geometry men contined from previos page Keystone Use this setting to compensate for any distortion cased by the projector being in a different horizontal or vertical plane to the screen. H Keystone V Keystone Rotation Reset Keystone 0 0 0 Keystone example 1 The projector is positioned at an angle 2 The reslting image is distorted 3 The image is corrected when Keystone is applied 1 2 3 Operating Gide page 49

USING THE PROJECTOR Geometry men contined from previos page Keystone settings 1 Projector to the left The projector is positioned to the left of the screen. To correct, apply a positive Horizontal Keystone vale sing the RIGHT arrow btton. 2 Projector to the right The projector is positioned to the right of the screen. To correct, apply a negative Horizontal Keystone vale sing the LEFT arrow btton. 3 Projector high The projector is positioned above the screen at a downward angle. To correct, apply a negative Vertical Keystone vale sing the DOWN arrow btton. 4 Projector low The projector is positioned below the screen at an pward angle. To correct, apply a positive Vertical Keystone vale sing the UP arrow btton. 1 2 5 Projector straight The projector is directly opposite the screen at a right angle both horizontally and vertically. No correction is needed. 3 4 5 Horizontal and vertical keystone corrections Operating Gide page 50

USING THE PROJECTOR Geometry men contined from previos page 4 Corners For each corner, apply horizontal and / or vertical correction as necessary to restore the rectanglar shape of the image. Top Left Corner Top Right Corner Bottom Left Corner Bottom Right Corner Reset 4 Corners Corner corrections provide a simple setp for awkward installations and irreglar shaped screens that may distort the image. To apply a similar (bt less flexible) correction, while preserving the original aspect ratio of the image, se the Keystone men. Top Right Corner example In this illstration, the top right corner reqires both horizontal and vertical correction. Top Right Corner Adjstment Top Right Corner x t 0 Top Right Corner y p 0 q Top Right Corner correction Operating Gide page 51

USING THE PROJECTOR Geometry men contined from previos page Rotation Use this featre for example to correct a monting error casing the image not to be level with the screen. Rotation example 1 DMD area The DMD is not rotated. It still covers the area that wold be occpied by the image withot correction. 2 Rotated image The image is smaller than the srronding DMD area. It is scaled in order to remain within the DMD area. 3 Angle of rotation The angle eqals a qarter of the Rotation setting. In this example the angle is 5, therefore Rotation = 20. Rotation Reset Rotation 0 1 3 2 Operating Gide page 52

USING THE PROJECTOR Geometry men contined from previos page Pincshion / Barrel Pincshion or barrel distortions are the reslt of poor or incorrect tensioning of the screen or sing a srface that is not flat. Use the Pincshion / Barrel control to compensate electronically for sch distortions. Yo can also se this men to make simple panoramic screen corrections withot sing external processors. Pincshion / Barrel H Pin/Barrel 0 V Pin/Barrel 0 Keystone Reset Pincshion / Barrel example The illstration shows pincshion and barrel correction applied both horizontally and vertically, in eqal measres. Pincshion Barrel Operating Gide page 53

USING THE PROJECTOR Geometry men contined from previos page Arc This featre is similar to Pincshion / Barrel bt allows yo to apply crvatre to each edge of the image independently so yo can have any combination of corrections. Arc Top 0 Bottom 0 Left 0 Right 0 Reset Please note that a positive Arc vale on any edge will redce the image size as the projector needs to maintain the aspect ratio. A negative Arc vale will not affect the overall image size. Operating Gide page 54

USING THE PROJECTOR Edge Blend men Use this men to blend together images from an array of two or more projectors. The featre feathers the light otpt of the projector within the edges that overlap with other projectors in the array: as a reslt, the overlapping edges are evenly lit and easily blend in with the rest of the image. Edge Blend Edge Blend On Align Pattern Off Blend Width Black Level Uplift When Edge Blend is set to Off, all other edge blend settings are disabled. Edge Blend Enable and disable Edge Blend Align Pattern Add markers to the image showing the edges of the blend area and making the overlaps more visible to help adjst the physical position of the projectors in the array. Blend Width Determine the width of the blended regions. Black Level Uplift Adjst black levels to compensate if the blended regions appear brighter than the rest of the image. Reset Reset all Edge Blend settings to their factory defalt vales. Reset The pictre in the blend region needs to be delivered to all overlapping projectors, which may reqire a special setp of the sorce. Operating Gide page 55

USING THE PROJECTOR Edge Blend men contined from previos page Blend Width Use the LEFT and RIGHT arrow bttons to set the width of the blended regions: Top Bottom Left Right Blend Width 0 0 0 0 1 Top 1 2 2 Bottom 3 Left 4 Right 3 4 Operating Gide page 56

USING THE PROJECTOR Edge Blend men contined from previos page Black Level Uplift Black in the blended regions appears less dark than in the rest of the image. To compensate for this, se this men to raise the black levels of the rest of the image: Set All to the reqired amont of black level correction. This will apply eqal correction to the black levels of all colors. If necessary, se the individal color sliders (Red, Green and Ble) for fine adjstment. Yo may experience artifacts at the edges where the blended region of one projector overlaps the pond of mirrors of its neighbor. In the example below, the blended image comes from two projectors, 1 and 2. Both images have black level plift applied; as a reslt, artifacts 3 and 4 have emerged at the edges where the black level plift region of one projector overlaps the pond of mirrors of the other. Top Bottom Left Right All Red Green Ble Black Level Uplift 0 0 0 0 0 0 0 0 Enable Align Pattern from the Edge Blend men to see the black level plift area. To remove the artifacts, yo need to slightly redce the size of the black level plift region of each projector so it does not overlap the pond of mirrors of the other projector. Depending on yor array, se Top, Bottom, Left and/or Right to redce the black level plift size. In the example below, se the Right slider of the projector on the left 1 to remove the artifact on the right 4, and the Left slider of the projector on the right 2 to remove the artifact on the left 3. 1 2 3 4 Operating Gide page 57

USING THE PROJECTOR 3D men Use this men to enable, disable and set p 3D inpt, as follows: 3D Format Off, Ato, Dal Pipe and Frame Seqential. Frame Seqential is displayed at the incoming rate whereas Dal Pipe interleaves the inpt to display p to 120 Hz. DLP Link Off / On. DLP Link On emits a sync plse for the 3D glasses via the projected image. DLP Link Off will send the sync plse to the sync ot connector to se with an external third party emitter. Eye Swap Normal and Reverse (set to Reverse if the left- and right-eye images are displayed in the wrong order) Dark Time 0.65 ms, 1.3 ms and 1.95 ms. Set to redce the effect of images overlapping while the glasses are switching. 3D Sync Offset se the LEFT and RIGHT arrow bttons to compensate for signal processing delays in the projector. Reference External and Internal. 3D Format DLP Link Eye Swap Dark Time 3D Sync Offset Reference 3D 100 Ato Off Normal 1.95 ms Internal 3D video is only possible on the HDMI 3 and HDMI 4 inpts. While the projector is in 3D mode, the OSD is navailable. Settings can be accessed via web pages served from the projector. For more information, see Served Web Pages. If 3D Format is set to Off, all other 3D settings will be navailable. For frther information abot spported 3D formats, see 3D connections in the Connection Gide. When 3D is on, the following settings become navailable: Image > Smooth Pictre, Brightness, Contrast, Satration, He, Sharpness, Noise Redction, Freeze, Resync. Color > Color Space. Geometry > Aspect Ratio, Digital Zoom, Overscan. Setp > Screen Setting, Ato Sorce, Trigger-1, Trigger-2. PIP > all settings. See also 3D types and Some 3D settings explained frther in this gide. See Appendix B: Spported Signal Inpt Modes > 3D formats in the Reference Gide for 3D resoltions and frame rates. Operating Gide page 58

USING THE PROJECTOR 3D men contined from previos page 3D types In most sitations yo can se the Ato setting to have the projector atomatically detect the format. Otherwise, consider the notes below to help yo set p the 3D inpt manally. The following 3D formats are spported: Dal Pipe (LEFT and RIGHT) The left and right eye images are delivered on two separate HDMI links, which the projector will interleave for 3D display. HDMI 1 L HDMI 2 R Dal Pipe Seqential Main will accept frame rates p to 160Hz. Lower frame rates can be mltiplied for display. An example wold be 60Hz (30 frames per eye in Left-Right seqence (L1, R1, L2, R2 ) with Frame Rate Mltiplier set to 2x, reslting in a displayed seqence at 120Hz (L1, R1, L1, R1, L2, R2, L2, R2 ). Sb can accept frame rates p to 60Hz and frame-mltiply in a similar manner. Frame Rate Mltiplier shold never be set to reslt in a displayed frame rate above 160Hz - doing so will reslt in an image error. For seqential 3D, an external sync is reqired to identify left and right frames. If no sync is available from the seqential sorce, the projector will generate an otpt sync, bt it may then be necessary to manally reset the dominance each time the player is started. L R L R Seqential Dark Time and Sync Delay need to be set only once, to optimize the image for the glasses in se. Operating Gide page 59

USING THE PROJECTOR 3D men contined from previos page Some 3D settings explained Dark Time Ghosting can be cased by the left and right images overlapping dring the time that the ZScreen or 3D glasses are switching. Dark Time allows yo to minimize this effect. Flly on Flly off Dark time Left Dark time Right Dark time In order to achieve maximm light otpt and a smooth grayscale, whilst eliminating ghosting, the following procedre is recommended: 1. Set Dark Time to a vale appropriate to the glasses or ZScreen, say 1.3 ms or 1.95 ms. Eye Swap The otgoing 3D frames are in pairs - the dominant frame being presented first. Yo can determine which frame shold be the dominant one. Dominance Left LEFT 1 RIGHT 1 LEFT 2 RIGHT 2 LEFT 3 RIGHT 3 2. Adjst Sync Offset time to eliminate ghosting and achieve a smooth grayscale. 3. Repeat steps 1 and 2 ntil the best reslt is obtained. By convention the defalt setting is Left. Dominance Right RIGHT 1 LEFT 1 RIGHT 2 LEFT 2 RIGHT 3 LEFT 3 Sync Delay The sync signal from the 3D server will be in phase with the frames generated by its graphics card. However, to compensate for processing delays in the projector, Sync Delay introdces a delay to the sync otpt signal sent to the ZScreen or 3D glasses. Incoming video Incoming sync signal Video signal with processing delays (and dark time adjstment) Sync otpt signal after delay adjstment Operating Gide page 60

Laser men USING THE PROJECTOR Laser Power Mode Eco will atomatically set the laser power to 80%. Normal will set the power to 100%. Set to Cstom if yo wish to adjst the power manally. Power Mode Power Level Normal Power Level This setting is only available if Power Mode is set to Cstom. Choose a vale between 20 and 100, ranging from 20% to 100% laser power. Operating Gide page 61

USING THE PROJECTOR Setp men Setp Orientation Choose from Front Tabletop, Front Ceiling, Rear Tabletop, Rear Ceiling and Ato-front. Cooling Condition Choose from Table, Ceiling, Freetilt and Ato. High Altitde Choose from On, Ato and Qiet. Standby Power Choose from SAVE, ECO and Normal. Screen Setting Choose from 16:10, 16:9 and 4:3. ColorMax Set p ser-defined color gamt vales. Power On/Off Management Access the sbmen to set p atomatic projector power on and power off. Clock Adjst Access the sbmen to set crrent date and local time. Startp Logo Set this to On if yo want the DP logo to show when the projector is first switched on. Blank Screen Choose from Logo, Black, Ble and White. Ato Sorce If this setting is On, the projector will atomatically search for an active inpt sorce. Orientation Cooling Condition High Altitde Standby Power Screen Setting ColorMax Power On/Off Management Clock Adjst Startp Logo Blank Screen Ato Sorce q Ato-front Ato Ato SAVE 16:9 On Logo Off Ato-front atomatically detects the projector s position and sets the orientation accordingly. Screen Setting and Ato Sorce are not available with inpt HDMI 3 or HDMI 4. Highlight the DOWN arrow at the bottom of the page and press ENTER/OK to navigate to the second Setp men page. Operating Gide page 62

USING THE PROJECTOR Setp men contined from previos page Trigger1 and Trigger 2 Choose from Screen, 5:4, 4:3, 16:10, 16:9, 1.88, 2.35, TheaterScope, Sorce, Unscaled or RS232 to determine what will case each trigger otpt to activate. Infrared Remote Set to Off if yo wish to disable the remote control. IR Code The projector and the remote control need a matching IR code: a two-digit nmber between 00 and 99. The defalt IR code is 00. This is also a master code, which, if assigned to a remote, will work regardless of the vale assigned to the projector. To assign an IR code for the projector: 1. Select IR Code. 2. Use the UP and DOWN arrow bttons to change the vales. To assign an IR code for the remote: 1. Press and hold the ADDR btton on the remote ntil the indicator starts flashing. 2. Release the ADDR btton and while the indicator is still flashing, enter a twodigit address sing the nmeric inpt bttons. The indicator will flash three times qickly to confirm the change. IR Code Reset Use this command to nassign an IR code from the projector. This will revert the IR Code vale to 00. Trigger-1 Trigger-2 Infrared Remote IR Code IR Code Reset OSD Settings Memory Setp p Off Off On 0 Trigger-1 and Trigger-2 are not available with inpt HDMI 3 or HDMI 4. If yo trn the remote control off, yo can only trn it back on again from the control panel or via the Projector Controller application. The Projector Controller software is available for download from the Digital Projection website, free of charge. A wired remote control will also be disabled if Infrared Remote is set to Off. To nassign an IR code from the remote control, Press and hold ALT and ADDR simltaneosly ntil the indicator flashes to confirm the change. OSD Settings Access this sbmen to adjst the appearance and position of the on-screen display. Memory Access this sbmen to save p to for presets containing cstom combinations of image settings, or to recall a saved preset. Highlight the UP arrow at the top of the page and press ENTER/OK to go back to the first Setp men page. Operating Gide page 63

USING THE PROJECTOR Setp men contined from previos page ColorMax Setting ColorMax Setting permits seven point color matching of red, green, ble, yellow, cyan, magenta and white. Yo can enter yor own gamt vales here, or edit vales yo have imported sing the Projector Controller software. Measred Data Target Data User 1 Target Data User 2 ColorMax Setting The Projector Controller software is available for download from the Digital Projection website, free of charge. Defining yor own colorspace with individal x and y coordinates for each color enables yo to match not only the whites bt each individal color as well. Highlight the sbmen yo wish to open and press ENTER/OK to confirm yor choice. This tool is best sed in conjnction with a specialized light meter (a photo spectrometer) to measre color parameters within a particlar installation. However, the preloaded generic factory defalt data set is designed to give more than satisfactory reslts. Measred Data / Target Data 1. Use the UP and DOWN arrow bttons to highlight a color, then se the LEFT and RIGHT arrow bttons to navigate to the x or y coordinate. 2. Use the UP and DOWN arrow bttons to increase and decrease the vale, respectively. 3. Exit edit mode: press ENTER/OK, if yo want to save the edited vales. press EXIT, if yo do not wish to save the edited vales Measred Data Red x: 0.658 y: 0.339 Green x: 0.315 y: 0.662 Ble x: 0.146 y: 0.043 White x: 0.276 y: 0.283 Reset Target Data User 1 Red x: 0.640 y: 0.390 Green x: 0.300 y: 0.600 Ble x: 0.150 y: 0.060 Yellow x: 0.419 y: 0.505 Cyan x: 0.225 y: 0.329 Magenta x: 0.321 y: 0.154 White x: 0.285 y: 0.302 Reset 4. If necessary, highlight another color and repeat the procedre. Operating Gide page 64

USING THE PROJECTOR Setp men contined from previos page Power On/Off Ato Power Off Set this to On if yo want the projector to go into STANDBY mode when no inpt sorce is detected for 20 mintes. Ato Power On Set this to On if yo want the projector to start p immediately when the mains is connected. Set this to Off if yo want the projector to go into STANDBY mode when the mains is connected. In this case, the projector will not start p ntil the POWER btton is pressed on the control panel or the ON btton is pressed on the remote control. Power On/Off Ato Power Off Off Ato Power On Off Schedled on/off Schedled on/off Access this sbmen to create a weekly schedle for atomatic on and off times: 1. Set a schedle: Use the UP and DOWN arrow bttons to highlight a row, then press ENTER/OK to enable edit mode. Within a row, navigate with the LEFT and RIGHT arrow bttons. Set vales with the UP and DOWN arrow bttons. To exit edit mode, press ENTER/OK. Alternatively, press EXIT if yo don t want the changes to take effect. Move to another row sing the UP and DOWN arrow bttons. 2. To enable the schedle, set Schedle to On. Schedled on/off Schedle Off S M T W T F S Time On T 12: 34 Off T 12: 34 On T 12: 34 Off T 12: 34 Operating Gide page 65

USING THE PROJECTOR Setp men contined from previos page Clock Adjst Use this men to set date (in dd:mm:yyyy format), time (in HH:mm format) and time zone. The date and time set here will affect any schedle created within the Power On/Off men. Clock Adjst Date (dd:mm:yyyy) 20:11:2015 Time (HH:mm) 14:00 Time Zone UTC 0 Operating Gide page 66

USING THE PROJECTOR Setp men contined from previos page OSD Settings Langage sets the OSD langage. Men Position determines where the OSD shold appear on the screen when activated. Men Transparency sets OSD transparency between 0% (no transparency), 25%, 50% and 75%. Time Ot determines how long the OSD shold remain on screen if no bttons are pressed. Choose Always On to disable this featre. Message Box determines whether projector stats messages shold appear on the screen. OSD Settings Langage English Men Position Center Men Transparency 0 Time Ot 30 Seconds Message Box On Memory The crrent image settings can be saved as a preset, which yo can recall later. The defalt settings can be recalled at any time as well. Up to for cstom presets can be stored for each inpt. The following settings are saved in a preset: From the Image men Dynamic Black, Smooth Pictre, Gamma, Brightness, Contrast, Satration, He, Sharpness and Noise Redction From the Color men Color Space, Color Mode, ColorMax, Color Temperatre, Dynamic Black, RGB Lift and RGB Gain From the Geometry men Aspect Ratio and Overscan Recall Memory Save Settings Memory Defalt Preset A Presets from one inpt cannot be applied to another inpt. Presets for inpts HDMI 3 and 4 do not contain all the settings normally stored for other inpts. To recall a saved preset: Select Recall Memory and press ENTER/OK, then select a preset from Preset A to Preset D. Select Defalt to load factory defalt vales. To save a preset: Select Save Settings and press ENTER/OK, then choose from Preset A, Preset B, Preset C and Preset D. Operating Gide page 67

USING THE PROJECTOR Network men DHCP, IP, Sbnet Mask, Gateway, DNS Set DHCP to On if the IP address is to be assigned by a DHCP server, or Off if it is to be set here. DHCP IP Network Off 192. 168. 000. 100 If DHCP is On, it will not be possible to edit IP Address, Sbnet Mask, Gateway or DNS. Sbnet Mask Gateway 255. 255. 255. 000 000. 000. 000. 000 If DHCP is set to Off, edit IP Address, Sbnet Mask, Gateway and DNS as reqired. DNS MAC 000. 000. 000. 000 00: 18: 27: 2d: f2: 06 MAC AMX Off This field is read-only. AMX Switch on or off. Operating Gide page 68

USING THE PROJECTOR PIP men PIP Trn PIP on and off. Sorce PIP Sorce Position PIP Off HDMI1 Top-Left PIP fnctionality is not available with inpts HDMI 3 and HDMI 4. Select an inpt sorce for the PIP image. Any combinations are possible between main and PIP inpt sorce, as long as one of the inpts is either DisplayPort or 3G-SDI. Position Set the location of the PIP image on the screen. Choose from Top-Left, Top-Right, Bottom-Left, Bottom-Right and PBP. Operating Gide page 69

USING THE PROJECTOR Information men This men gives information abot software and hardware configration, inpt sorce and laser operating times It also allows yo to restore the factory defalt settings. Information Model Name E-Vision Laser 4K Serial Nmber X000XXXXX0000 Software Version 1 MD03-SE10-FE09 Software Version 2 STEP-D14-RE04-3092 Software Version 3 1.10.2.7-P496 Active / PIP Sorce HDMI 1 Signal Format Laser Hors 41 System Stats Thermal Stats Factory Reset Signal Format Active Sorce Signal Format Timing H Refresh V Refresh Pixel Clock 1080p/60Hz 67.500 KHz 60.00 Hz 148.500 MHz PIP Sorce Timing H Refresh V Refresh Pixel Clock 576p/50Hz 31.250 KHz 50.00 Hz 27.0 MHz PIP Sorce items are not available with inpt HDMI 3 or HDMI 4. Operating Gide page 70

USING THE PROJECTOR Information men contined from previos page System Stats System Stats Atmospheric Pressre AC Voltage Ceiling Mode Tilt Angle Portrait Angle Altitde Mode Laser Power 98988 Pa (116 m) 160V 264V 0 4 deg 0 deg Low 100% Thermal Stats Thermal Stats Inlet 1/2 Temp. DMD Temp. Laser 1/2 Temp. Otside Temp. Fan 1-3 Speed Fan 4-6 Speed Fan 7-9 Speed Fan 10-12 Speed Fan 13-15 Speed Fan 16 Speed Water Pmp Speed 24 / 34 (C) 38 (C) 49 / 42 (C) 32 (C) 1399 / 1402 / 1391 1410 / 1200 / 1205 1211 / 1407 / 1410 0 / 3005 / 3007 2986 / 2984 / 2984 3020 / NA / NA 3506 Operating Gide page 71

USING THE PROJECTOR Information men contined from previos page Factory Reset To restore the factory defalt settings: 1. Navigate to Factory Reset and press ENTER/OK. 2. When prompted, press ENTER/OK to confirm yor choice, or press EXIT to cancel. Software Version 2 Factory Reset LE07-14-RE04-3092 WARNING Active Sorce HDMI All Signal ser Format settings will be lost! Laser Hors Press OK to confirm 00041 HRS System Stats Press Exit to cancel Thermal Stats Operating Gide page 72

SERVED WEB PAGES Served Web Pages The served web pages allow yo to control the projector remotely via LAN. The defalt IP address is 192.168.0.100. Projector Stats Projector Control Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Projector Information Model E-Vision Laser 4K Serial Nmber W714ZETCY0003 Software Version 1 MD03-VD03-FE12-0.0.356 Software Version 2 STEP_D08-24-16-3120 Software Version 3 1.10.5.0-P503 Power Stats - Inpt - Laser Stats Power : - Rntime : - H Projection Mode - High Altitde - Inlet Temperatre - C DMD Temperatre - C LD Temperatre - C Diagnostic Stats - LAN Information MAC address 00:18:23:50:92:DA Operating Gide page 73

SERVED WEB PAGES Projector Stats Projector Control Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp State Control Power On Off Inpt Selection DisplayPort HDMI 1 HDMI 2 HDBaseT 3G-SDI HDMI 3 (3D) HDMI 4 (3D) Error Log DP OSD Fnction Lens Control Hot Key PicMte OSD Freeze Zoom In Focs In Shift Zoom OUT Focs OUT Operating Gide page 74

SERVED WEB PAGES Projector Stats Projector Control Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze NetWork DHCP: IP Address: Sbnet Mask: Gateway: DNS Server: On Off 192. 168. 0. 100 255. 255. 255. 0 192. 168. 0. 254 192. 168. 0. 1 Save Settings CAUTION: Incorrect settings may case the projector to lose network connectivity. Operating Gide page 75

SERVED WEB PAGES Projector Stats Server Setp Projector Control SMTP Server: Port: Crestron RoomView User Name: 25 Network Setp Password: Alert Mail Setp Apply Date/Time Setp Error Log Mail DP OSD Fnction Hot Key PicMte OSD E-mail Alert: From: To: Enable Disable Freeze CC: Projector Name: W714ZETCY0003 Location: Apply Test Send Test Mail Periodic Report days Times Sn Mon Te Wed Th Fri Sat 00:00 01:00 02:00 03:00 04:00 05:00 06:00 07:00 08:00 09:00 10:00 11:00 12:00 13:00 14:00 15:00 16:00 17:00 18:00 19:00 20:00 21:00 22:00 23:00 reset Save Set Operating Gide page 76

SERVED WEB PAGES Projector Stats Projector Control Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Time Zone: Time Zone: GMT(-12:00) Select Local time zone, Crrent zone is GMT +00:00 SaveTimeZone Time: Date: 2000.01.26 e.g.2000.01.01 Clock: 16:10 e.g.23:59 Crrent time is set to :- ; - SaveTime Projector Stats Projector Control Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Projector Error Log ErrLog: 3 / Crrent PowerOn times: 10 No Code PwrOn L1(Hr/Pwr/Vol) T(Ti/Tc) FANs Desc 1 0825 5 0/0/0 0/0 (NoData) ErrWheelSpinEnv 2 0825 4 0/0/0 0/0 (NoData) ErrWheelSpinEnv 3 0825 6 0/0/0 0/0 (NoData) ErrWheelSpinEnv 1 0825 5 0/0/0 0/0 (NoData) ErrWheelSpinEnv 2 0825 4 0/0/0 0/0 (NoData) ErrWheelSpinEnv 3 0825 6 0/0/0 0/0 (NoData) ErrWheelSpinEnv Page 1 Page 2 Operating Gide page 77

SERVED WEB PAGES Projector Stats Projector Control Inpt Page 1 Page 2 Page 3 Crestron RoomView Inpt HDMI2 Network Setp Alert Mail Setp Test Pattern Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Lens Exit Test Pattern Lens Lock off on CenterLens Do Lens Type non-ust Lens UST Lens LensMemory Memory 1 Save Load Clear Image PictreMode Hight Bright DynamicBlack off on Gamma 2.2 Brightness Constrast Statration He Sharpness Noise Redction Low Freeze Resync - + 100 - + 100 - + 100 - + 100 - + 10 color Operating Gide ColorSpace ColorMode Ato ColorMax page 78

SERVED WEB PAGES Projector Stats Projector Control geometry Page 1 Page 2 Page 3 Crestron RoomView Network Setp Alert Mail Setp Aspect Ratio Sorce Digital Zoom Digital Zoom Digital Pan Digital Scan - + 0% - + 0 - + 0 Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Digital Zoom Reset Overscan Off Blanking Top Bottom Left Right Blanking Reset Keystone H Keystone V Keystone Rotation - + 0 - + 0 - + 0 - + 0 - + 0 - + 0 - + 0 Keystone Reset 4 Corners Top Left Corner X Top Left Corner Y Top Right Corner X Top Right Corner Y Bottom Left Corner X Bottom Left Corner Y Bottom Right Corner X Bottom Right Corner Y - + 0 - + 0 - + 0 - + 0 - + 0 - + 0 - + 0 - + 0 4 Corners Reset Rotation - + 0 Rotation Reset Pincshion/Barrel H Pin/Barrel V Pin/Barrel Keystone H Keystone V Keystone Rotation - + 0 - + 0 - + 0 - + 0 - + 0 Pincshion/Barrel Reset Operating Gide Arc Top 0 page 79

SERVED WEB PAGES Projector Stats Projector Control setp Page 1 Page 2 Page 3 Crestron RoomView Network Setp Alert Mail Setp Date/Time Setp Error Log DP OSD Fnction Hot Key PicMte OSD Freeze Orientation Ato-front Colling Condition Ato High Altitde On Screen Setting 16:9 ColorMax Measred Data Red Green Ble White Measred Data Reset Target Data - User 1 Red Green Ble Yellow Cyan Magenta White X:0.650 Y:0.341 X:0.343 Y:0.622 X:0.141 Y:0.021 X:0.305 Y:0.343 X:0. 650 Y:0. 341 X:0. 343 Y:0. 622 X:0. 141 Y:0. 021 X:0. 411 Y:0. 557 X:0. 230 Y:0. 318 X:0. 269 Y:0. 099 X:0. 305 Y:0. 343 Target Data - User 1 Save Target Data - User 1 Reset Target Data - User 2 Red Green Ble Yellow Cyan Magenta White X:0. 650 X:0. 343 X:0. 141 X:0. 411 X:0. 230 X:0. 269 X:0. 305 Y:0. 341 Y:0. 622 Y:0. 021 Y:0. 557 Y:0. 318 Y:0. 099 Y:0. 343 Target Data - User 2 Save Target Data - User 2 Reset Operating Gide Power On/Off Ato Power Off Ato Power On Schedled on/off off off off on on on Sn Mon Te Wed Th Fri Sat Time(HH:MM) On 00:00 Off 00:00 On 00:00 Off page 80

E-Vision Laser 4K Series High Brightness Digital Video Projector 4 REFERENCE GUIDE

IN THIS GUIDE IN THIS GUIDE The DMD... 83 Choosing A Lens... 85 Basic calclation...86 Basic calclation example...87 Fll lens calclation...88 Introdcing TRC...88 Calclating TRC...89 Calclating the throw ratio with TRC...90 Fll lens calclation example...91 Positioning the screen and projector... 92 Positioning The Image... 93 Frame Rates And Plldowns Explained... 95 Interlaced and progressive scan...95 Frame rates of image sorces...95 Plldowns - conversion into destination formats...96 2:3 (normal) plldown...96 2:3:3:2 (advanced) plldown...97 Appendix A: Lens Part Nmbers... 98 Appendix B: Spported Signal Inpt Modes... 99 2D formats...99 SDI formats... 102 3D formats... 103 Appendix C: Wiring Details... 104 RS232... 104 Trigger 1 & Trigger 2... 105 Wired remote control... 105 Sync IN, Sync OUT and 3D Sync IR... 105 Appendix D: Glossary Of Terms... 106 Reference Gide

THE DMD The DMD A DMD (Digital Micromirror Device ) is a tre digital light modlator which tilises an array of p to 2.3 million moving alminim mirrors, with each one representing a pixel in the final projected image. The otermost micromirrors in the array remain inactive (pond of mirrors) and are not sed in constrcting the image. 1 Casing 2 Light shield 3 Pond of mirrors 4 Array 1 2 3 4 DMD Each mirror element is sspended over address electrodes by a torsion hinge between two posts. 1 Spport posts 1 2 Mirror element 3 Torsion hinges 4 Offset address electrode 2 3 4 Mirror element with tilt mechanism Reference Gide page 83

THE DMD Depending on the voltage polarity applied, each mirror will either tilt to the left to prodce a bright pixel or to the right for a dark pixel. When light is applied to the complete DMD, only the light redirected from a mirror tilting to the left is projected. 1 Projection lens 5 2 Incoming light from the illmination modle 3 Mirror element tilted to the right 1 2 4 Mirror element tilted to the left 5 Reflected light, left tilt 6 7 6 Light dmp 7 Reflected light, right tilt 3 4 Light flow The projector optically filters white light from the illmination modle into its constitent red, green and ble. Each color illminates a separate DMD whose modlated otpt is then recombined with the other two to form the projected fll color image. 1 Illmination modle 1 2 3 2 Optical filtering of light into red, green and ble 3 Projection lens white light RGB light 4 DMD devices 5 Fll color image displayed on screen ble light green light red light 4 5 Filtering process Reference Gide page 84

CHOOSING A LENS Choosing A Lens A nmber of lenses are available. Which lens yo choose depends on the screen size, image aspect ratio, throw distance and light otpt. The following table shows all available lenses in order of their throw ratios: Throw ratios Focs range Lens shift 0.38 : 1 fixed (UST)* 0.68 m - 2.44 m Depends on image size, see UST Lens Installation Gide (separate docment). 0.75-0.93 : 1 zoom 1.02 m - 12.7 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame 0.76 : 1 fixed* 0.81 m - 5.08 m none 1.25-1.79 : 1 zoom 1.33 m - 11.73 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame 1.72-2.27 : 1 zoom 1.83 m - 14.9 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame 2.22-3.67 : 1 zoom 2.36 m - 24.2 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame 3.58-5.38 : 1 zoom* 3.8 m - 35.35 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame 5.31-8.26 : 1 zoom* 5.59 m - 54.8 m V: 0.5 (U) 0 (D) frame H: 0.1 (L) 0.1 (R) frame Lenses marked with an asterisk (*) above are only available for High Brightness projectors. All other lenses have High Contrast conterparts. To choose a lens, calclate the throw ratio reqired. Throw distance calclations are based on the distance from the oter end of the lens, which will vary from lens to lens. The distance between the front of the projector chassis and the oter end of the lens is called lens extension. Lens extensions is measred when the lens is focsed at infinity, and flly extended. Refer to the projector CAD drawings for individal lens extension figres. The 0.38 : 1 fixed lens has no adjstable shift vale. However, the lens has an inherent offset depending on image size. See the UST docmentation pblished separately on the Digital Projection website. The 0.75-0.93 : 1 zoom lens has an additional featre permitting barrel correction for crved screens. The front ring of the lens is a manal control which provides focs crvatre adjstment to correct for the different focal distances between center and corner. Throw ratios of High Contrast lenses differ slightly from their High Brightness conterparts. For details, see Appendix A at the end of this docment. For information abot individal lens part nmbers, see Appendix A at the end of this docment. Reference Gide page 85

CHOOSING A LENS Basic calclation Identify the reqired lens by calclating the throw ratio. A throw ratio is the ratio of the throw distance to the screen width: Throw distance Throw ratio = Screen width 1. Use the formla above to obtain the reqired throw ratio. 2. Match the throw ratio with a lens from the table below: Throw ratios Focs range 0.38 : 1 fixed (UST) 0.82 m - 2.71 m 0.75-0.93 : 1 zoom 1.02 m - 12.7 m 0.76 : 1 fixed 0.81 m - 5.08 m 1 Throw distance 1.25-1.79 : 1 zoom 1.33 m - 11.73 m 1.72-2.27 : 1 zoom 1.83 m - 14.9 m 2 Screen width 2.22-3.67 : 1 zoom 2.36 m - 24.2 m 3.58-5.38 : 1 zoom 3.8 m - 35.35 m 5.31-8.26 : 1 zoom 5.59 m - 54.8 m 3. Ensre the reqired throw distance is within the range covered by the lens. 1 2 The lens table shown on this page incldes High Brightness lenses only. For a fll list, see Appendix A at the end of this docment. The basic calclation on this page does not take into consideration DMD and image size, which cold affect the throw ratio. For a more complex and realistic calclation, see Fll lens calclation in this section. When calclating the throw ratio, be sre to se identical measrement nits for both the throw distance and the screen width. For information abot individal lens part nmbers, see Appendix A at the end of this docment. Reference Gide page 86

Basic calclation example CHOOSING A LENS 1. Calclate the throw ratio sing the formla. Yor screen is 4.5 m wide and yo wish to place the projector approximately 11 m from the screen. The throw ratio will then be 11 = 2.44 4.5 2. Match the reslt with the lens table. The lens matching a throw ratio of 2.44 is the 2.22-3.67 : 1 zoom lens. 3. Check whether the lens covers the reqired throw distance. The focs range qoted for the 2.22-3.67 : 1 zoom lens is 2.36-24.2 m. The reqired distance of 11 m is within the range. INFORMATION YOU NEED FOR THIS CALCULATION The throw ratio formla: Throw distance Throw ratio = Screen width The lens table: Throw ratios Focs range 0.38 : 1 fixed (UST) 0.82 m - 2.71 m 0.75-0.93 : 1 zoom 1.02 m - 12.7 m 0.76 : 1 fixed 0.81 m - 5.08 m 1.25-1.79 : 1 zoom 1.33 m - 11.73 m 1.72-2.27 : 1 zoom 1.83 m - 14.9 m 2.22-3.67 : 1 zoom 2.36 m - 24.2 m 3.58-5.38 : 1 zoom 3.8 m - 35.35 m 5.31-8.26 : 1 zoom 5.59 m - 54.8 m The lens table shown on this page incldes High Brightness lenses only. For a fll list, see Appendix A at the end of this docment. The basic calclation on this page does not take into consideration DMD and image size, which cold affect the throw ratio. For a more complex and realistic calclation, see Fll lens calclation in this section. For information abot individal lens part nmbers, see Appendix A at the end of this docment. Reference Gide page 87

CHOOSING A LENS Fll lens calclation Introdcing TRC The choice of lens will affect the image size and will address discrepancies between the DMD resoltion and the sorce. When an image fills the height of the DMD bt not the width, it ses less than 100% of the DMD srface. A lens chosen sing the basic formla may prodce an image that is considerably smaller than the actal screen. To compensate for loss of screen space in sch sitations, yo need to increase the throw ratio sing a Throw Ratio Correction (TRC). TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. Example Fig. 1 illstrates a 4:3 image within a WUXGA DMD. Fig. 1 When a WUXGA projector is sed for a 4:3 image, the image does not fill the width of the DMD, creating a pillarboxing effect - blank spaces to the left and right. Fig. 2 shows the same image projected on a 4:3 screen sing a standard lens (chosen with the basic calclation). The DMD accrately fills the width of the screen; however, the pillarboxing is now part of the projected image and is transferred to the screen. The DMD does not fill the height of the screen, which has cased letterboxing - frther blank spaces at the top and bottom of the screen. The image is now srronded by blank space, which can be removed if the throw ratio is increased. Fig. 2 Fig. 3 shows the image projected on the same screen with a lens chosen sing TRC. The increased throw ratio has allowed the 4:3 image to fill the 4:3 screen seamlessly. Fig. 3 Reference Gide page 88

CHOOSING A LENS Calclating TRC To calclate TRC, se the following formla: TRC = 1.6 (DMD aspect ratio) Sorce aspect ratio TRC table Alternatively, yo can save time by referencing the following table, which shows the TRC vale for some poplar image formats: TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. 2.35:1 (Scope), 1920 x 817 pixels TRC < 1, not sed 1.85:1 (Flat), 1920 x 1037 pixels TRC < 1, not sed 1.78:1 (16:9), 1920 x 1080 TRC < 1, not sed 1.66:1 (Vista), 1792 x 1080 pixels TRC < 1, not sed 1.6:1 (16:10), 1728 x 1080 pixels TRC = 1, not sed (native resoltion) 1.33:1 (4:3), 1440 x 1080 pixels TRC = 1.2 1.25:1 (5:4), 1350 x 1080 pixels TRC = 1.28 Reference Gide page 89

CHOOSING A LENS Calclating the throw ratio with TRC 1. For TRC > 1, amend the basic throw ratio formla as follows: Throw ratio = Throw distance Screen width x TRC 2. Once a throw ratio is established, identify the matching lens from the table: Throw ratios Focs range 0.38 : 1 fixed (UST) 0.82 m - 2.71 m 0.75-0.93 : 1 zoom 1.02 m - 12.7 m 0.76 : 1 fixed 0.81 m - 5.08 m 1.25-1.79 : 1 zoom 1.33 m - 11.73 m 1.72-2.27 : 1 zoom 1.83 m - 14.9 m 2.22-3.67 : 1 zoom 2.36 m - 24.2 m 3.58-5.38 : 1 zoom 3.8 m - 35.35 m 5.31-8.26 : 1 zoom 5.59 m - 54.8 m 3. Ensre the reqired throw distance is within the range of the matching lens. The lens table shown on this page incldes High Brightness lenses only. For a fll list, see Appendix A at the end of this docment. TRC can only be applied if greater than 1. If TRC is 1 or less, disregard it and calclate the throw ratio sing the basic formla. Reference Gide page 90

Fll lens calclation example Yor screen is 4.5 m wide; yo wish to place the projector approximately 11 m from the screen. The sorce is 4:3. 1. Calclate TRC as follows: TRC = 1.6 1.33 = 1.2 2. Calclate the throw ratio: 11 Throw ratio = = 2.04 4.5 x 1.2 3. Find a match in the lens table. The table shows that the matching lens is the 1.72-2.27 : 1 zoom lens. 4. Check whether the lens covers the reqired throw distance. The focs range qoted for the 1.72-2.27 : 1 zoom lens is 1.83-14.9 m. The reqired distance of 11 m is within the range. CHOOSING A LENS INFORMATION YOU NEED FOR THESE CALCULATIONS The TRC formla TRC = DMD aspect ratio Sorce aspect ratio The TRC table (to se instead of the formla) 2.35:1 (Scope) TRC not sed 1.85:1 (Flat) TRC not sed 1.78:1 (16:9) TRC not sed 1.66:1 (Vista) TRC not sed 1.6:1 (16:10) TRC not sed (native resoltion) 1.33:1 (4:3) TRC = 1.2 1.25:1 (5:4) TRC = 1.28 Throw distance The throw ratio formla Throw ratio = Screen width x TRC The lens table: Throw ratios Focs range 0.38 : 1 fixed (UST) 0.82 m - 2.71 m 0.75-0.93 : 1 zoom 1.02 m - 12.7 m 0.76 : 1 fixed 0.81 m - 5.08 m 1.25-1.79 : 1 zoom 1.33 m - 11.73 m 1.72-2.27 : 1 zoom 1.83 m - 14.9 m 2.22-3.67 : 1 zoom 2.36 m - 24.2 m 3.58-5.38 : 1 zoom 3.8 m - 35.35 m 5.31-8.26 : 1 zoom 5.59 m - 54.8 m The lens table shown on this page incldes High Brightness lenses only. For a fll list, see Appendix A at the end of this docment. Reference Gide page 91

POSITIONING THE SCREEN AND PROJECTOR Positioning the screen and projector For optimm viewing, the screen shold be a flat srface perpendiclar to the floor. The bottom of the screen shold be 1.2 m (4 feet) above the floor and the front row of the adience shold not have to look p more than 30 to see the top of the screen. The distance between the front row of the adience and the screen shold be at least twice the screen height and the distance between the back row and the screen shold be a maximm of 8 times the screen height. The screen viewing area shold be within a 60 range from the face of the screen. The projector shold be installed as close to the power otlet as possible. The power connection shold be easily accessible, so that it can be disconnected in an emergency. Ensre that there is at least 30 cm (12 in) of space between the ventilation otlets and any wall, and 10 cm (4 in) on all other sides. Do not install the projector close to anything that might be affected by its operational heat, for instance, polystyrene ceiling tiles, crtains etc. The image can be flipped for rear projection (see Setp men in the Operating Gide) and displayed withot the need for extra mirrors or eqipment. However, yo mst ensre that there is sfficient distance behind the screen for the projector to be correctly located. Rear installation is generally more complicated and advice shold be soght from yor local dealer before attempting it. Reference Gide page 92

POSITIONING THE IMAGE Positioning The Image The normal position for the projector is at the centre of the screen. However, yo can set the projector above or below the centre, or to one side, and adjst the image sing the Lens shift featre (known as rising and falling front) to maintain a geometrically correct image. Shifting the lens p (rising front) Centered lens Shifting the lens down (falling front) Reference Gide page 93

POSITIONING THE IMAGE Any single adjstment otside the ranges specified on the following page may reslt in an nacceptable level of distortion, particlarly at the corners of the image, de to the image passing throgh the periphery of the lens optics. If the lens is to be shifted in two directions combined, the maximm range withot distortion will be somewhat less, as can be seen in the illstrations below. Fll horizontal or vertical shift Combined shift is redced Reference Gide page 94

FRAME RATES AND PULLDOWNS EXPLAINED Frame Rates And Plldowns Explained Interlaced and progressive scan A progressive scan is a method of pdating the image by drawing all the lines of each frame in a seqence. In contrast, interlaced video alternately scans odd and even lines. In old analog TV interlacing was commonly sed as a way of dobling the refresh rate withot consming extra bandwidth. The following artifacts are common with interlaced video: edge tear (combing) The image lands between two fields and blrs. This is commonly observed when viewing rapid lateral movement. aliasing (stair-stepping) The textre of the image becomes poplated with nrealistic patterns. Aliasing occrs becase of differences between the original frame rate and the destination format. twitter The image shimmers, for example when showing rolling credits. This happens when the image contains thin horizontal lines that only appear in one field. Frame rates of image sorces Original analog films are made at 24 fps and the whole frame is projected at once. To eliminate flicker and create an impression of continos movement, the projector blades divide the images so that the viewer sees 48 frames per second. Interlaced video scans odd lines, then even. Two fields are blended into one image. NTSC video (60i) is 29.97 fps, or 59.94 fields per second. 24p video is progressive bt withot the benefit of projector blades dividing the images, so it looks jmpier on playback than film. 24p is the optimal format for projects that are finished on film. 30p is optimal for projects finished on video. It has fewer strobing isses than 24p in video playback. Reference Gide page 95

FRAME RATES AND PULLDOWNS EXPLAINED Plldowns - conversion into destination formats Plldowns are a method of converting a 24p sorce into a different destination format by adding extra frames to the sorce. 2:3 (normal) plldown This method is sed to convert a 24p sorce (film) into a 60i destination (NTSC video) by adding two extra fields for every for frames, effectively increasing the frame rate to 30 fps. The frame is split into fields and then two fields are repeated for every for original frames as shown in the illstration below. Original film, 24 fps Field 1 (odd) Field 2 (even) Reslting video, 30 fps Reference Gide page 96

FRAME RATES AND PULLDOWNS EXPLAINED 2:3:3:2 (advanced) plldown This method is very similar to the normal plldown. Unlike the normal plldown method, the reslting 30 fps video seqence contains only one frame containing fields from two different sorce frames. The advantage of this method is that it is easier to reverse, if necessary. Original film, 24 fps Field 1 (odd) Field 2 (even) Reslting video, 30 fps The projector will se advanced plldown on sitable video material, wherever possible. Reference Gide page 97