R&S DDF200M Digital Direction Finder Specifications Data Sheet Version 02.00
CONTENTS Definitions... 3 Specifications... 4 Frequency... 4 Direction finding... 4 Linearity... 4 Interference rejection... 5 Sensitivity... 5 A/D converter resolution... 5 Antenna inputs... 5 Inputs/outputs... 5 Data rate via LAN... 6 DF antennas... 6 R&S ADD090 VHF DF antenna... 6 R&S GX090 antenna network... 6 Interference canceller module (ICM)... 6 R&S GX090C combiner network... 6 General data... 7 R&S DDF200M and R&S GX090C combiner network... 7 R&S ADD090 DF antenna and R&S GX090 antenna network... 7 2 Rohde & Schwarz R&S DDF200M Digital Direction Finder
Definitions General Product data applies under the following conditions: Three hours storage at ambient temperature followed by 30 minutes warm-up operation Specified environmental conditions met Recommended calibration interval adhered to All internal automatic adjustments performed, if applicable Specifications with limits Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked with limiting symbols such as <,, >,, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is derived from the design. Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if applicable. Specifications without limits Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent values with no or negligible deviations from the given value (e.g. dimensions or resolution of a setting parameter). Compliance is ensured by design. Typical data (typ.) Characterizes product performance by means of representative information for the given parameter. When marked with <, > or as a range, it represents the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents the mean value. Nominal values (nom.) Characterize product performance by means of a representative value for the given parameter (e.g. nominal impedance). In contrast to typical data, a statistical evaluation does not take place and the parameter is not tested during production. Measured values (meas.) Characterize expected product performance by means of measurement results gained from individual samples. Uncertainties Represent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has been calculated in line with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into account environmental conditions, aging, wear and tear. Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz. Rohde & Schwarz R&S DDF200M Digital Direction Finder 3
Specifications Frequency Frequency range, DF mode base unit, depending on DF antenna 118 MHz to 450 MHz Frequency range, receive mode base unit 118 MHz to 450 MHz Frequency resolution 1 Hz BFO 0 Hz to ±8 khz Frequency accuracy 1 10 6 Input for external reference 10 MHz Synthesizer setting time 1 ms, 900 µs (typ.) Oscillator phase noise 118 MHz to 450 MHz 120 dbc (1 Hz) at 10 khz offset Direction finding DF method correlative interferometer Instrument DF accuracy across entire frequency range 0.5 RMS System DF accuracy with R&S ADD090, in reflection-free 1 RMS, 0.5 RMS (typ.) environment, including lightning protection, DF error correction not required DF sensitivity with R&S ADD090, field strength 5 µv/m required for 2 RMS, 15 khz DF bandwidth, 1 s integration time Polarization vertical Minimum signal duration without ICM 1 DF1 mode: 100 ms with ICM DF3 mode: 600 ms Response time from start of emission to output of the 200 ms DF result at the R&S DDF200M interface Bearing resolution 0.1 Operating modes DF1: DF on single frequency channel with fast measurement speed (without ICM) DF2: quasi-simultaneous DF up to 4 frequency channels DF3: DF on single frequency channel with higher sensitivity DF4: quasi-simultaneous DF on up to 32 frequency channels in maritime VHF range (156 MHz to 162 MHz), plus up to 4 additional frequencies outside this range Channel spacing for wideband direction finding DF4 mode only (10 MHz realtime bandwidth) 1 MHz, 500/200/100/50/25/20/12.5/10/8.33/ 6.25/5/3.125 khz DF bandwidths defined by channel spacing 600/300/120/60/30/15/12/7.5/6/5/ 3.75/3/1.875 khz Modulation modes capable of direction finding all Linearity Second-order intercept point (SOI) 118 MHz to 450 MHz low distortion mode 50 dbm (typ.) normal mode 40 dbm (typ.) Third-order intercept point (TOI) 118 MHz to 450 MHz low distortion mode (2 MHz spacing at 20 dbm) 118 MHz f 450 MHz 15 dbm, 19 dbm (typ.) normal mode (2 MHz spacing at 30 dbm) 118 MHz f 450 MHz 7 dbm, 10 dbm (typ.) 1 Interference canceller module. 4 Rohde & Schwarz R&S DDF200M Digital Direction Finder
Interference rejection Image rejection 118 MHz f 450 MHz 80 db, 90 db (typ.) IF rejection 118 MHz f 450 MHz 80 db Sensitivity Sensitivity (demodulation) 118 MHz to 450 MHz normal mode AM: bandwidth = 6 khz, SINAD = 12 db, f mod = 1 khz, m = 0.5 FM: bandwidth = 15 khz, SINAD = 20 db, f mod = 1 khz, deviation = 5 khz SSB: bandwidth = 2.4 khz, SINAD = 12 db, f = 1 khz CW: bandwidth = 600 Hz, SINAD = 12 db A/D converter resolution Resolution measurement using telephone filter in line with ITU-T 107 dbm ( 1 µv) 107 dbm ( 1 µv) 113 dbm ( 0.5 µv) 119 dbm ( 0.25 µv) 16 bit Antenna inputs DF antenna inputs base unit 1 input Monitoring antenna inputs VHF/UHF 1 input, N female, 50 Ω VSWR 2 Input level 137 dbm to +10 dbm Max. input level (nondestructive) +15 dbm Oscillator reradiation at antenna input 90 dbm, 100 dbm (typ.) Inputs/outputs Inputs External reference 10 MHz input level: 0 dbm to 10 dbm Control signals GPS/compass, trigger, blank Outputs Internal reference 10 MHz output level: 3 dbm to 7 dbm Video A, video B analog video, AM (A) and FM (B), DC to ½ IF bandwidth or analog IF, controlled, 2 channels, adjustable center frequency: 0 Hz to 70 MHz, bandwidth equal to IF filter bandwidth, level 11 dbm Digital video LAN, bandwidth 5 MHz Digital I/Q LAN, bandwidth 5 MHz Analog audio headphone connector 0 V to 2 V, R i = 100 Ω, f min = 10 Hz to 300 Hz, f max = 12.5 khz (depends on IF filter and demodulation) AF line 0.5 V ± 0.2 V (m = 0.5), R i = 100 Ω, f min = 10 Hz to 300 Hz, f max = 12.5 khz (depends on IF filter and demodulation) AF balance 0.4 V ± 0.2 V (m = 0.5), R i = 600 Ω, f min = 100 Hz, f max = 12.5 khz Control signals signal > squelch threshold, COR, antenna control LAN for data transfer and remote control 1 Gbit Ethernet interface Serial interface control via SCPI RS-232 backward compatible with R&S DDF100M RS-232 (with R&S DDF200M-SE option) Rohde & Schwarz R&S DDF200M Digital Direction Finder 5
Data rate via LAN DF2 mode 4 frequency channels in maritime VHF range (156 MHz to 162 MHz) DF4 mode 32 frequency channels in maritime VHF range (156 MHz to 162 MHz) plus 4 channels out of this range DF antennas with ICM (R&S GX090C) without ICM (R&S GX090 mod.12, measurement time 330 ms) with ICM (R&S GX090C) without ICM (R&S GX090 mod.12, measurement time 100 ms) without ICM (R&S GX090 mod.12, measurement time 1 s) 5.5 kbit/s 7 kbit/s 18 kbit/s 2, 7.7 kbit/s (typ.) 42 kbit/s 2, 20 kbit/s (typ.) 4.2 kbit/s 2, 2 kbit/s (typ.) R&S ADD090 VHF DF antenna Frequency range 118 MHz to 250 MHz Antenna type 9 passive antenna elements DF method correlative interferometer Polarization vertical DF accuracy with installed lightning protection 1 RMS, 0.5 RMS (typ.) (lightning rod or R&S ADD-LP) Reflection immunity DF error with 50 % reflections in field 1.7 RMS strength DF sensitivity 5 µv/m (typ.) Power supply from DF equipment Dimensions Ø H, without lightning rod approx. 2.07 m 0.8 m (6.79 ft 2.62 ft) Ø H, with lightning rod approx. 2.07 m 2 m (6.79 ft 6.56 ft) Weight approx. 40 kg (88.18 lb) Permissible wind speed without ice deposit 275 km/h with 30 mm radial ice deposit 210 km/h R&S GX090 antenna network Frequency range 118 MHz to 250 MHz Dimensions W H D approx. 0.49 m 0.21 m 0.35 m (1.61 ft 0.69 ft 1.15 ft) Weight approx. 10 kg (22.05 lb) Interference canceller module (ICM) R&S GX090C combiner network Frequency range desired signals 118 MHz to 250 MHz interfering signals 150 MHz to 174 MHz Number of RF paths 2 Maximum number of interfering signals 6 Insertion loss of each RF path max. 3 db, < 2.5 db (typ.) Maximum input power desired signals plus interfering signals 0 dbm Characteristic impedance 50 Ω Interference suppression interference signal level: 5 dbm 40 db (typ.) interference sensor power from 0.75 W to 1.5 W max. interference level at the output: 40 dbm (typ.) Operating modes operation, bypass, freeze, test Power supply 10 V to 18 V DC, max. 2 A at 12 V Dimensions W H D approx. 0.47 m 0.18 m 0.4 m (1.54 ft 0.59 ft 1.31 ft) Weight approx. 10 kg (22.05 lb) 2 Maximum data rate occurs during DF output for maritime VHF range (wideband DF of 32 channels). 6 Rohde & Schwarz R&S DDF200M Digital Direction Finder
General data R&S DDF200M and R&S GX090C combiner network Environmental conditions Climatic conditions in line with EN 60068-2-1, EN 60068-2-2 Operating temperature range 0 C to +50 C Permissible temperature range 10 C to +55 C Storage temperature range 40 C to +70 C with AC/DC adapter 20 C to +70 C Humidity (noncondensing) max. 95 %, +25 C/+55 C Operating altitude 6000 m Environmental tests Shock in line with MIL-STD-810E, meth. 516.4, procedure I Vibration sinusoidal 5 Hz to 150 Hz, in line with EN 60068-2-6 random 10 Hz to 500 Hz, in line with EN 60068-2-64 Electromagnetic compatibility (EMC) in line with EN 55022, ETSI EN 301489-1, ETSI EN 301489-22 MTBF (IEC 1709) > 33000 h Power consumption without DF antenna 60 W (typ.) with DF antenna 96 W (typ.) Power supply AC 100 V to 240 V, 50 Hz to 60 Hz, with external AC/DC adapter DC 10 V to 32 V, 12 A to 4 A Mechanical parameters (R&S DDF200M) Dimensions W H D 213 mm 132 mm 450 mm (8.39 in 5.20 in 17.72 in), ½ 19", 3 HU Weight approx. 6.8 kg (14.99 lb) R&S ADD090 DF antenna and R&S GX090 antenna network Operating temperature range 40 C to +65 C, in line with MIL-STD-810F, meth. 501.4 and 502.4, procedure II Storage temperature range 40 C to +85 C, in line with MIL-STD-810F, meth. 501.4 and 502.4 Humidity 95 %, +25 C/+55 C, in line with EN 60068-2-30 Vibration sinusoidal 5 Hz to 55 Hz, 0.15 mm amplitude constant, 55 Hz to 150 Hz, 0.5 g const., in line with EN 60068-2-6 random 10 Hz to 300 Hz: 0.01 g 2 /Hz, 300 Hz to 500 Hz: 0.003 g 2 /Hz, in line with EN 60068-2-64 mobile application: vehicles, without lightning rod 3 Hz to 500 Hz, 0.00047/0.295/0.00082 g 2 /Hz (approx. 1.76 g RMS), adapted to MIL-STD-810E, meth. 514.4 (measured data) Shock resistance spectrum 45 Hz to 2000 Hz, max. 40 g, in line with MIL-STD-810E, meth. 516.4, procedure I, DIN IEC 60068-2-27 with limitations (sawtooth 40 g/11 ms) Class of protection IP55, in line with EN 60529 Lightning protection (against direct strikes) up to an installation height of 20 m protection class IV (Î = 100 ka, dl/dt = 100 ka/ms), in line with IEC 1024-1 Resistance to salt fog in line with MIL-STD-810F, meth. 509.4 For product brochure, see PD 3606.8837.12 and www.rohde-schwarz.com Rohde & Schwarz R&S DDF200M Digital Direction Finder 7
Service that adds value Worldwide Local and personalized Customized and flexible Uncompromising quality Long-term dependability Rohde & Schwarz The Rohde & Schwarz electronics group offers innovative solutions in the following business fields: test and measurement, broadcast and media, secure communications, cybersecurity, monitoring and network testing. Founded more than 80 years ago, the independent company which is headquartered in Munich, Germany, has an extensive sales and service network with locations in more than 70 countries. Sustainable product design Environmental compatibility and eco-footprint Energy efficiency and low emissions Longevity and optimized total cost of ownership Certified Quality Management ISO 9001 Certified Environmental Management ISO 14001 Rohde & Schwarz GmbH & Co. KG www.rohde-schwarz.com Rohde & Schwarz training www.training.rohde-schwarz.com Regional contact Europe, Africa, Middle East +49 89 4129 12345 customersupport@rohde-schwarz.com North America 1 888 TEST RSA (1 888 837 87 72) customer.support@rsa.rohde-schwarz.com Latin America +1 410 910 79 88 customersupport.la@rohde-schwarz.com Asia Pacific +65 65 13 04 88 customersupport.asia@rohde-schwarz.com China +86 800 810 82 28 +86 400 650 58 96 customersupport.china@rohde-schwarz.com R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG Trade names are trademarks of the owners PD 3606.8837.22 Version 02.00 January 2018 (fi) R&S DDF200M Digital Direction Finder Data without tolerance limits is not binding Subject to change 2014 2018 Rohde & Schwarz GmbH & Co. KG 81671 Munich, Germany 3606.8837.22 02.00 PDP 1 en 3606883722