VM617 AND VM619 FLAT PANEL LCD MONITORS

XX171-00-00 VM617 AND VM619 FLAT PANEL LCD MONITORS Copyright 2005 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788 TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: +44 (0) 1489-566300 WEB: www.vicon-cctv.com Vicon part number 8009-8171-00-00 Section 6 Rev 1105

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: CAUTION Explanation of Graphical Symbols The lightning symbol in the triangle tells you that the voltage inside this product may be strong enough to cause an electric shock. DO NOT TRY TO SERVICE THIS PRODUCT YOURSELF. The exclamation point in the triangle tells you that important operating and maintenance instructions follow this symbol. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE PRONGS CAN BE FULLY INSERTED INTO THE OUTLET TO PREVENT ANY EXPOSURE OF THE PRONGS ON THE POLARIZED PLUG. XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors Explanation of Graphical Symbols 1

Important Information IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated. 2. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. 3. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to. 4. FOLLOW INSTRUCTIONS All operating and usage instructions should be followed. 5. CLEANING Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean only with a dry cloth. 6. ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards. 7. WATER AND MOISTURE Do not use this unit near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 8. ACCESSORIES Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9. VENTILATION Slots and openings at the rear cabinet and bottom are provided for ventilation. These are to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to. 10. POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. 11. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 12. LIGHTNING To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. 13. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 14. OVERLOADING Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock. 15. OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit. 16. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 17. CONNECTING When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections. 18. LCD Do not press on or jolt the LCD panel. Doing so may cause the LCD panel glass to break and injury may occur. Should the LCD panel be broken and liquid leaks out, do not inhale or swallow it. Doing so may cause poisoning. If you have got it into your mouth, wash it out and consult your doctor. If your hands or clothes have touched it, wipe them with alcohol and a cleaning cloth and then wash them well. 2 Explanation of Graphical Symbols XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Features 17 / 19 TFT LCD Screen Supports up to SXGA Resolution RGB In (15-Pin D-Sub) 2 Video In/Out (BNC) 2 Stereo Audio In/Out S-Video In VESA Standard Wall and Arm Mountable Built-In Stereo Speaker Components LCD Color Monitor 1 Accessories Power Cord 1 User Manual 1 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 3

Front Panel Description The monitor is operated by using the buttons on the front panel. The side panels provide the inputs to connect other equipment to the monitor. Front Panel AUTO: AUTO MENU DOWN UP SOURC E POWER Auto-optimize displaying picture under PC mode. MENU: ADJUST: SOURCE: POWER: OSD menu ON/OFF control. Increase or decrease the value on OSD menu. Up: Increase value or turn ON/OFF function. Down: Decrease value or turn ON/OFF function Select input signal from AV1, AV2, S-Video or VGA (PC). Monitor power ON/OFF. At OFF mode, monitor is at standby status. Green Light: ON Mode Orange Light: Standby Mode (AV1, AV2, S-Video) Red Light: OFF Mode 4 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Back and Side Description Back Side 1 2 5 6 9 3 4 7 8 10 11 12 13 14 15 16 1, 2 AUDIO 2 IN (L, R) Stereo Audio Signal Input for AV2 or PC 3, 4 AUDIO 2 OUT (L, R) Audio looping outputs for AUDIO 2 5, 6 AUDIO 1 IN (L, R) Stereo Audio Signal Input for AV1 or Y/C 7, 8 AUDIO 1 OUT (L, R) Audio looping outputs for AUDIO 1 9 S-Video IN Y/C separated signal input 10 VIDEO 2 OUT Video looping output for VIDEO 2 11 VIDEO 2 IN Composite signal Input for VIDEO 2 12 VIDEO 1 OUT Video looping output for VIDEO 1 13 VIDEO 1 IN Composite signal Input for VIDEO 1 14 PC AUDIO IN 15 Signal VGA IN 16. 100 VAC ~240 VAC Input XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 5

Selecting a Location for the Monitor Place the monitor on the floor or on a sturdy platform in a location where light does not directly hit the screen. Place the monitor far enough from the walls to allow proper ventilation. Inadequate ventilation may cause overheating, which may damage the monitor. Caution: Be careful when using the back stand; in some angles, the monitor may fall over to the front. When using the back stand, be careful not to catch your fingers between the folding stand. It may cause you unnecessary injury. Connecting the Monitor If you don t have previous experience with electronic equipment connection, read this section completely before continuing with the installation. Note: Cables are not supplied; they are mentioned just for reference. Audio cables are usually color coded according to use: red and white for audio. The red audio cable is for the stereo right channel and the white audio cable is for the stereo left (or mono) channel. The terminals on the rear panel of the monitor are color coded in the same manner as the cables. S-video cables provide better picture performance than standard video cables. S-video cables can only be used with S-video compatible components. BNC cables provide better connection and picture performance. Audio Cable S-Video BNC Connector NOTE: To prevent equipment damage, do not plug in any power cords until you have finished connecting all equipment. 6 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Monitor Setup AUTO MENU DOWN UP SOURC E POWER 1. Turning the monitor on/off: Press POWER: The power indicator lamp (green) will light and the image will be displayed. Press POWER again: The power indicator lamp (red) will light and the power will be turned off. 2. Switching the source: Press SOURCE. Each press will switch the source in order. 3. Press MENU to enter to OSD setup. 4. Use ADJUST to select the OSD mode or to change the adjust value. 5. Press AUTO for auto optimize displaying picture under PC mode. GENERAL SETUP VIDEO SETUP VGA SETUP EXIT General Setup: Video Setup: VGA Setup: EXIT: Configure General Signal Power Latching, Power Auto On, Key Lock, Language, Back Light, Display, Video Loss Setup, V-Loss Sleep Time, Volume and Exit. Configure Video Signal Brightness, Contrast, Color, Tint, Sharpness, Video System, Scan Mode, Color Temperature, Default and Exit. Configure VGA Signal Auto, Brightness, Contrast, Color Temperature, White Balance, H-Position, V-Position, Clock, Phase, Default and Exit. Exit the on-screen menu. XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 7

General Setup POWER LATCHING: POWER AUTO ON: KEY LOCK: LANGUAGE: BACKLIGHT: DISPLAY: VIDEO LOSS SETUP: V-LOSS SLEEP TIME: VOLUME: EXIT: This OSD feature allows the system to memorize the power status before powering off. ON: Enable the function. OFF: Disable the function. Setting the video input priority whenever power is turned ON. AV1: Set channel to AV1 when power is turned ON. AV2: Set channel to AV2 when power is turned ON. S-Video: Set channel to S-Video when power is turned ON. VGA: Set channel to VGA when power is turned ON. None: No changing. This function provides protection when an unauthorized person tries to access the OSD settings. ON: Key-lock function enabled. OFF: Key-lock function disabled. Key-lock release: To release key-lock function, press Up and Down for more than 5 sec. Allows user to select the language, English, Spanish or French. Allows user to adjust the panel s backlight luminance. When pressing the Up/Down button, the number displayed will not be in serial order. Show/Hide channel title ON: Show channel title OFF: Hide channel title after approx. 5 sec. Controls monitor luminance when video is not detected. Controls video loss count down timer. To adjust the built-in speakers output volume Exit the on-screen menu. 8 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Video Setup BRIGHTNESS 68 CONTRAST 23 COLOR 22 TINT 50 SHARPNESS 80 VIDEO SYSTEM NTSC SCAN MODE LARGE COLOR TEMP 6500 DEFAULT BRIGHTNESS: Adjusts the overall picture shade and brightness. CONTRAST: Provides adjustment for contrast between light and dark areas of the picture. When pressing the Up/Down button, the number displayed will not be in serial order. COLOR: Adjusts the color gain on the screen. Please note that the color will not be black-and-white when turning the number down to 0. TINT: Adjusts overall colors onscreen. (NTSC only) When pressing the Up/Down button, the number displayed will not be in serial order. SHARPNESS: Sets the desired sharpening enhancement to the picture. When pressing the Up/Down button, the number displayed will not be in serial order. VIDEO SYSTEM: Displays video system types in NTSC or PAL (display only). SCAN MODE: Selects monitor display format. Select LARGE to permit the picture to be larger than the actual display area. Select SMALL to constrain the picture to the size of the display. LARGE: Permits the displaying picture to be larger than actual displaying area. SMALL: Permits the displaying picture to approximately match the actual size of displaying area. COLOR TEMP: Selects color temperature of either 6500 K or 9300 K. DEFAULT: Sets the monitor to the original factory setting. Original factory setting (General Setup, Video Setup). EXIT: Exits the on-screen menu. XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 9

VGA Setup AUTO BRIGHTNESS 50 CONTRAST 100 COLOR TEMP 9300 WHITE BALANCE H POSITION 54 V POSITION 50 CLOCK 50 PHASE 64 DEFAULT EXIT AUTO: BRIGHTNESS: CONTRAST: COLOR TEMP: WHITE BALANCE: H-POSITION: V-POSITION: CLOCK: PHASE: DEFAULT: EXIT: Auto-optimizes displaying picture under PC mode. Adjusts the overall picture shade and brightness. Adjusts the contrast between light or dark areas of the picture Selects color temperature to either 6500 k or 9300 K. Allows the overall picture performance in gray-scale optimization. Adjusts the horizontal position. Adjusts the vertical position. Use to adjust best picture quality. It adjusts the numbers of the pixel clock across one line at a time. Therefore, it can affect the picture position and size. Use to adjust best picture quality. It adjusts the sampling phase across one pixel at a time. When the phase is not adjusted properly, the picture will be unclear. Therefore this value should be carefully adjusted. Sets the monitor to the original factory setting. Original factory setting (VGA Setup). Exits the on-screen menu. 10 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

LCD Monitor Mounting Guide Desktop Adjust the viewing angle of LCD monitor to fit most comfortable monitoring status. Arm Mount (VESA Standard) When adjusting the VESA Standard Arms to the back side of the LCD monitor, use the 4x8 (mm) screw. For further information, refer to the Arm Manual. 45 15 15 Mounting the monitor on the rack Rack Mount Note: When adjusting to a rack, an optional rack mount is needed for the back side of the LCD monitor. Optional rack mounts sold separately. XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 11

Connecting Device Audio 2 IN Audio 2 OUT Loop out to another video device DVD or other video source Camera or other video source Camera or other video source Audio 1 IN Audio source Audio 1 OUT S-Video IN Video 2 OUT Video 2 IN Video 1 OUT Video 1 IN PC Audio IN PC VGA AC IN 1. Connect PC to Monitor through VGA connector as shown on the above picture. 2. Connect external device, such as DVD or Game Player, to Monitor as shown on the above picture. 3. Connect CCD Camera 1 and 2 to Monitor through Video Input 1 and 2 (BNC connector) as shown on the above picture. 4. Support resolution. 17 Monitor Display Modes Mode Resolution Refresh Rate VGA 640x480 up to 75Hz SVGA 800x600 up to 75Hz XGA 1024x768 up to 75Hz SXGA 1280x1024 up to 75Hz 19 Monitor Display Modes Mode Resolution Refresh Rate VGA 640x480 up to 75Hz SVGA 800x600 up to 75Hz XGA 1024x768 up to 75Hz SXGA 1280x1024 up to 75Hz Although this monitor supports above RGB signals, any resolutions not matched by this monitor (SXGA) will be expanded or shrunk, which will affect image quality. To view high-quality images, it is recommended that the PC's resolution should be set to SXGA (1280x1024) resolution. 12 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Troubleshooting Before calling a service technician, please check the following table for a possible cause of the problem and a solution. Symptom Monitor will not turn on No picture, no sound No sound, picture OK Poor color, sound OK Poor color or no color Solution Make sure the power cord is plugged in, then press POWER button. Check cable connections. There is no sound in Video Loss. Check audio cable connections. Try pressing Volume Up button in the Menu. Check cable connections. Adjust Video set up menu. Adjust Color and/or Tint (NTSC only). XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 13

LCD Color Monitor Specification Model Number VM617 VM619 Panel Size 17.0 19.0 Aspect Ratio 4:3 4:3 640 x 480 @ 60/72/75 640 x 480 @ 60/72/75 800 x 600 800 x 600 Resolution/Scan @ 56/60/72/75 @ 56/60/72/75 1024 x 768 1024 x 768 @ 60/70/75 @ 60/70/75 1280 x 1024 @ 60/75 1280 x 1024 @ 60/75 Brightness 250cd/m 2 (*1) 250cd/m 2 ( 1) Viewing Angle(H/V) 160 /160 160 /160 Response Time 12ms (Typ) 12ms (Typ) Sync. Format NTSC/PAL Frequency (Horizontal) PC: 31.5K - 80KHz, Video 15750 / 15625Hz (NTSC / PAL) ( 2) Frequency (Vertical) PC: 56Hz -75Hz, Video: 50 / 60Hz ( 2) Video Interface D-SUB 15IN x 1, Video In x 2 (BNC), Video Out x 2 (BNC), S-Video In x 1 Input Audio Interfaces Interface Audio In x 2, Audio Out x 2, PC-Audio In x 1 Input Power AC In x 1 Termination 75ohm (Auto Termination) Built-in Speakers Yes (2 pcs) Front Panel Button Power, Source, Up/Down, Menu, Auto OSD Language English, French, Spanish VESA Mounting VESA 100 Weight 12.3 lb (5.6 kg) 14.3 lb (6.5 kg) External Dimensions (WxHxD) 15.4x13.9x2.9 in. (390x354.5x74.2 mm) 16.7x15.6x3.0 in. (425x396x75.6 mm) Safety & EMI UL, CUL, FCC/B, CE Power 100-240 VAC 50/60Hz ( 3) Power Consumption (max) 40 W 40 W Temp (Oper.) 14 F ~122 F (-10 C to 50 C) Humidity 20% ~ 80% Accessories Power Cord, User Manual ( 1) The brightness spec. 250cd/m 2 is from panel spec. ( 2) It is not guaranteed for all the specified range. ( 3) Use the supplied power supply cord at 120 VAC or less. Design and Specifications are subject to change without notice. 14 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

LCD Color Monitor Dimensions XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors 15

Maintenance The VN617 and VM619 monitors require no scheduled maintenance. Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. Vicon Industries Inc. 89 Arkay Drive Hauppauge, NY 11788 Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288) For service or returns from countries in Europe, contact: Vicon Industries Ltd Brunel Way Fareham, PO15 5TX United Kingdom Phone: +44 (0) 1489/566300; Fax: +44 (0) 1489/566322 2. Attach a sheet of paper to the unit with the following information: a. Name and address of the company returning the unit b. Name of the Vicon employee who issued the R.A. c. R. A. number d. Brief description of the installation e. Complete description of the problem and circumstances under which it occurs f. Unit s original date of purchase, if still under warranty 3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection. 4. Mark the R.A. number on the outside of the carton on the shipping label. 16 Maintenance XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors

Vicon Standard Equipment Warranty Vicon Industries Inc. (the Company ) warrants your equipment to be free from defects in material and workmanship under Normal Use from the date of original retail purchase for a period of three years, with the following exceptions: 1. VCRs, all models: Labor and video heads warranted for 120 days from date of original retail purchase. All other parts warranted for one year from date of original retail purchase. 2. Kollector Elite, Kollector Pro and ViconNet Systems (hardware only), all models: Hard Drives warranted for three years. All other parts warranted for 18 months. 3. AurorAcorD: Hard drives, floppy drives, CD-R/W, DVD drives and any and all archive media warranted for 18 months. All other parts warranted for three years from date of original retail purchase. 4. RAID Storage Devices and Hard Drives, all models: Warranted for one year from date of original retail purchase. 5. Video monitor CRT (cathode ray tube) and LCD monitors, all models: One year from date of original retail purchase. 6. NOVA 1500 CPU: Hard drives, floppy drives, CD-R/W drives and any and all archive media, warranted for 18 months. All other parts warranted for 3 years from date of original retail purchase. 7. Normal Use excludes prolonged use of lens and pan-and-tilt motors, gear heads, and gears due to continuous use of autopan or tour modes of operation. Such continuous operation is outside the scope of this warranty. Date of retail purchase is the date original end-user takes possession of the equipment, or, at the sole discretion of the Company, the date the equipment first becomes operational by the original end-user. The sole remedy under this Warranty is that defective equipment be repaired or (at the Company s option) replaced, at Company repair centers, provided the equipment has been authorized for return by the Company, and the return shipment is prepaid in accordance with policy. The Company will not be obligated to repair or replace equipment showing abuse or damage, or to parts which in the judgment of the Company are not defective, or any equipment which may have been tampered with, altered, misused, or been subject to unauthorized repair. Software supplied either separately or in hardware is furnished on an As Is basis. Vicon does not warrant that such software shall be error (bug) free. Software support via telephone, if provided at no cost, may be discontinued at any time without notice at Vicon s sole discretion. Vicon reserves the right to make changes to its software in any of its products at any time and without notice. This Warranty is in lieu of all other conditions and warranties express or implied as to the Goods, including any warranty of merchantability or fitness and the remedy specified in this Warranty is in lieu of all other remedies available to the Purchaser. No one is authorized to assume any liability on behalf of the Company, or impose any obligations on it in connection with the sale of any Goods, other than that which is specified above. In no event will the Company be liable for indirect, special, incidental, consequential, or other damages, whether arising from interrupted equipment operation, loss of data, replacement of equipment or software, costs or repairs undertaken by the Purchaser, or other causes. This warranty applies to all sales made by the Company or its dealers and shall be governed by the laws of New York State without regard to its conflict of laws principles. This Warranty shall be enforceable against the Company only in the courts located in the State of New York. The form of this Warranty is effective August 2, 2004. THE TERMS OF THIS WARRANTY APPLY ONLY TO SALES MADE WHILE THIS WARRANTY IS IN EFFECT. THIS WARRANTY SHALL BE OF NO EFFECT IF AT THE TIME OF SALE A DIFFERENT WARRANTY IS POSTED ON THE COMPANY S WEBSITE, WWW.VICON-CCTV.COM. IN THAT EVENT, THE TERMS OF THE POSTED WARRANTY SHALL APPLY EXCLUSIVELY. Vicon Part Number: 8006-9010-03-01 Rev 804 XX171-00-00 Rev 1105 VM617/VM619 Flat Monitors Vicon Standard Equipment Warranty 17

Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322 Brussels Office Planet II - Unit E Leuvensesteenweg 542 B-1930 Zaventem Belgium +32 (2) 712 8780 Fax: +32 (2) 712 8781 Far East Office Unit 5, 17/F, Metropole Square 8 On Yiu Street, Shatin New Territories, Hong Kong (852) 2145-7118 Fax: (852) 2145-7117 Internet Address: www.vicon-cctv.com