TITLE : HT190E Product Specification Rev. B

Transcription

1 PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF OE TFTLCD SU AND SHALL NOT E REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF OE TFT LCD SU AND MUST E RETURNED TO OE HYDIS UPON ITS REQUEST TITLE : HT9E Product Specification Rev. OE TFTLCD SU EIJING OE OPTOELECTRONICS TECHNOLOGY OE HYDIS TECHNOLOGY SPEC. NUMER. S86422 TFTLCD OF 29 25CO(/3) A4(2 X 297)

2 TFT LCD PRODUCT ISION HISTORY. ECN No. DESCRIPTION OF CHANGES DATE PREPARED Initial Release W.K. Chang A E56F Weight : 25 g max. 25 g max W.K.Chang E58F9.Add View Angle Spec at CR> W.K.Chang : 8/8/8/8 Typ. 7/7/7/7 Min. 2.Divide Response Time Spec from Total into Rising and Falling Rising : 2 ms Typ. 4 ms Max. Falling : 6 ms Typ. 8 ms Max. SPEC. NUMER S86422 SPEC. TITLE HT9E Product Specification 2 OF 29 25CO(2/3) A4(2 X 297)

3 TFT LCD PRODUCT Contents No Item General Description Absolute Maximum Ratings Electrical specifications Optical specifications Interface Connection Signal Timing Specifications Signal Timing waveforms of Interface Signal Input Signals, Display Colors & Gray Scale of Colors Power Sequence Mechanical Characteristics Reliability Test Handling & Cautions Product Serial Number Packing Appendix Page SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 3 OF 29 25CO(3/3) A4(2 X 297)

4 . GENERAL DESCRIPTION. Introduction TFT LCD PRODUCT HT9E is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 9. inch diagonally measured active area with SXGA resolutions (28 horizontal by 24 vertical pixel array). Each pixel is divided into RED, GREEN, LUE dots which are arranged in vertical stripe and this module can display 6,94,227 colors. The TFTLCD panel used for this module is adapted for a low reflection and higher color type. CN2 CN22 Connector (CN ) LVDS Input Signal VDD LVDS Rx + T/CON + minilvds Tx DC/DC Gamma Vcom Gate Driver Source Driver TFT LCD Panel CN23 CN24.2 Features LVDS Interface with 2 pixel / clock Highspeed response Low power consumption 6bit (FRC) color depth, display 6,94,227 colors Incorporated edge type backlight (Four lamps) High luminance and contrast ratio, low reflection and wide viewing angle DE (Data Enable) & HSync & VSync mode RoHS Compliant SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 4 OF 29 25CO(3/3) A4(2 X 297)

5 TFT LCD PRODUCT Application Desktop Type of PC & Workstation Use SlimSize Display for Standalone Monitor Display Terminals for Control System Monitors for Process Controller.4 General Specification The followings are general specifications at the model HT9E. <Table. General Specifications> Parameter Specification Unit Remarks Active area (H) * 3.6(V) mm Number of pixels 28(H) 24(V) pixels Pixel pitch.294(h).294(v) mm Pixel arrangement RG Vertical stripe Display colors 6,94,227 colors Display mode Normally White Dimensional outline 396.(H) 324.(V) 6.5(D) typ. mm Weight 25 (max.) g Surface Treatment Haze 25%, 3H acklight Top/ottom edge side, 4CCFL type SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 5 OF 29 25CO(3/3) A4(2 X 297)

6 TFT LCD PRODUCT ASOLUTE MAXIMUM RATINGS The followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and nonoperational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS=GND=V] Parameter Symbol Min. Max. Unit Remarks Power Supply Voltage Logic Supply Voltage V DD V IN VSS.5 VSS V DD +.3 V V Ta = 25 acklight Lamp Current I L 3 8 ma acklight Lamp frequency F L 3 8 khz Operating Temperature T OP +5 ) Storage Temperature T ST 2 +6 ) Note : ) Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 O C max. and no condensation of water. 9 Relative Humidity (%RH) O perating Range Storage Range Tem perature ( C) SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 6 OF 29 25CO(3/3) A4(2 X 297)

7 TFT LCD PRODUCT 3. ELECTRICAL SPECIFICATIONS 3.Electrical Specifications < Table 3. Electrical specifications > [Ta =25±2 ] Parameter Min. Typ. Max. Unit Remarks Power Supply Voltage Power Supply Current V DD I DD V ma Note Permissible Input Ripple Voltage V RF mv V DD = 5.V High Level Differential Input Threshold Voltage Low Level Differential Input Threshold Voltage V IH V IL + mv mv Vcm =.2V typ. acklight Lamp Voltage V L V rms acklight Lamp Current I L ma rms acklight Lamp operating Frequency F L 3 7 KHz Note 2 Lamp Start Voltage 4 7 V rms V rms 25, Note 3, Note 3 Lamp Life 5 Hrs I L = 8.mA Power Consumption P D W P L 8.6 W I L =7.5mA, Note 4 P total W Notes :. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.V, Frame rate=75hz and Clock frequency = 67.5MHz. Test Pattern of power supply current a) Typ : Color ar pattern b) Max : Dot pattern 2. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 3. The voltage above this value should be applied to the lamps for more than second to startup. Otherwise the lamps may not be turned on. 4. Calculated value for reference (V L I L ) 4 excluding inverter loss. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 7 OF 29 25CO(3/3) A4(2 X 297)

8 TFT LCD PRODUCT OPTICAL SPECIFICATION 4. Overview The test of Optical specifications shall be measured in a dark room (ambient luminance lux and temperature = 25±2 ) with the equipment of Luminance meter system (Goniometer system and TOPCONE M5) and test unit shall be located at an approximate distance 5cm from the LCD surface at a viewing angle of θ and Φ equal to. We refer to θ Ø= (=θ 3 ) as the 3 o clock direction (the right ), θ Ø=9 (= θ 2 ) as the 2 o clock direction ( upward ), θ Ø=8 (= θ 9 ) as the 9 o clock direction ( left ) and θ Ø=27 (= θ 6 ) as the 6 o clock direction ( bottom ). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 3 minutes warmup period. VDD shall be 5.V +/% at 25 C. Optimum viewing angle direction is 6 clock. 4.2 Optical Specifications Parameter Viewing Angle range Viewing Angle range Luminance Contrast ratio Luminance of White Horizontal Vertical Horizontal Vertical Symbol Θ 3 Θ 9 Θ 2 Θ 6 Θ 3 Θ 9 Θ 2 Θ 6 CR Y w [VDD = 5.V, Frame rate = 6Hz, Clock = 54MHz, I L = 7.5mA, Ta =25±2 ] Condition CR > CR > 5 White luminance uniformity ΔY 75 8 % Note 4 W x White W y Θ = (Center) R x Normal Red R y Viewing Reproduction Angle Note 5 of color G x Green G y Min Typ Max. Unit Deg. Deg. Deg. Deg. Deg. Deg. Deg. Deg. cd/m 2 Remark Note Note 2 Note 3 lue x..4.7 y Response Time Rising Falling T r T f ms ms Note 6 Cross Talk CT 2. % Note 7 SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 8 OF 29 25CO(3/3) A4(2 X 297)

9 TFT LCD PRODUCT Note :. Viewing angle is the angle at which the contrast ratio is greater than. The viewing are determined for the horizontal or 3, 9 o clock direction and the vertical or 6, 2 o clock direction with respect to the optical axis which is normal to the LCD surface. 2. Contrast measurements shall be made at viewing angle of θ= and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. CR = Luminance when displaying a white raster Luminance when displaying a black raster 3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 9points / Maximum Luminance of 9points ) * (See FIGURE 2 shown in Appendix). 5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electrooptical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the data input signal ON and OFF. The times needed for the luminance to change from % to 9% is Td, and 9% to % is Tr. 7. CrossTalk of one area of the LCD surface by another shall be measured by comparing the luminance (Y A ) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (Y ) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix). SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 9 OF 29 25CO(3/3) A4(2 X 297)

10 TFT LCD PRODUCT INTERFACE CONNECTION. 5. Electrical Interface Connection CN Module Side Connector : JAE FIX3SSRLHF6 or Equivalent User Side Connector : JAE FIX3H or Equivalent Pin No Symbol RXO RXO+ RXO RXO+ RXO2 RXO2+ GND RXOCLK RXOCLK+ RXO3 RXO3+ RXE RXE+ GND RXE RXE+ GND RXE2 RXE2+ RXECLK RXECLK+ RXE3 RXE3+ GND NC NC NC VDD VDD VDD Function LVDS ODD SIGNAL LVDS ODD + SIGNAL LVDS ODD SIGNAL LVDS ODD + SIGNAL LVDS ODD 2 SIGNAL LVDS ODD 2+ SIGNAL GROUND LVDS ODD CLOCK SIGNAL LVDS ODD CLOCK+ SIGNAL LVDS ODD 3 SIGNAL LVDS ODD 3+ SIGNAL LVDS EVEN SIGNAL LVDS EVEN + SIGNAL GROUND LVDS EVEN SIGNAL LVDS EVEN + SIGNAL GROUND LVDS EVEN 2 SIGNAL LVDS EVEN 2+ SIGNAL LVDS EVEN CLOCK SIGNAL LVDS EVEN CLOCK+ SIGNAL LVDS EVEN 3 SIGNAL LVDS EVEN 3+ SIGNAL GROUND NO CONNECTION NO CONNECTION NO CONNECTION POWER SUPPLY ( +5. V ) Remark Note Internal Use Internal Use Internal Use Note : This pin should be connected with GND. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification OF 29 25CO(3/3) A4(2 X 297)

11 TFT LCD PRODUCT LVDS Interface (Tx; THC63LVDF83A or Equivalent) 5.2. ODD LVDS Interface O D D L V D S Input Signal OR OR OR2 OR3 OR4 OR5 OG OG OG2 OG3 OG4 OG5 O O O2 O3 O4 O5 Hsync Vsync DE MCLK OR6 OR7 OG6 OG7 O6 O7 RSVD Pin No Transmitter Pin No System (Tx) OUT OUT+ OUT OUT+ CLK OUT CLK OUT+ OUT2 OUT2+ OUT3 OUT3+ Interface TFTLCD (Rx) RXO RXO+ RXO RXO+ RXO CLK RXO CLK+ RXO2 RXO2+ RXO3 RXO3+ FIX3SSRL HF6 Pin No Remark SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification OF 29 25CO(3/3) A4(2 X 297)

12 TFT LCD PRODUCT EVEN LVDS Interface E V E N L V D S Input Signal ER ER ER2 ER3 ER4 ER5 EG EG EG2 EG3 EG4 EG5 E E E2 E3 E4 E5 Hsync Vsync DE MCLK ER6 ER7 EG6 EG7 E6 E7 RSVD Pin No Transmitter Pin No System (Tx) OUT OUT+ OUT OUT+ CLK OUT CLK OUT+ OUT2 OUT2+ OUT3 OUT3+ Interface TFTLCD (Rx) RXE RXE+ RXE RXE+ RXE CLK RXE CLK+ RXE2 RXE2+ RXE3 RXE3+ FIX3SSRL HF6 Pin No Remark SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 2 OF 29 25CO(3/3) A4(2 X 297)

13 TFT LCD PRODUCT Data Input Format ODD (,) EVEN (2,) (279,) (28,) R G R G R G R G Pixel = 3 Dots R G R G R G R G R G (,24) (2,24) Display Position of Input Data (VH) (279,24) (28, 24) 5.4 acklight Interface Connection CN 2,22,23,24 PIN NO. 2 Module Side Connector User Side Connector INPUT HOT COLD :35HS2L(YeonHo) or Equivalent :35HS2L(YeonHo) or Equivalent COLOR FUNCTION Pink & lue High Voltage lack & White Ground SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 3 OF 29 25CO(3/3) A4(2 X 297)

14 TFT LCD PRODUCT SIGNAL TIMING SPECIFICATION 6. The HT9E is operated by the DE & HSync & VSync mode ( LVDS Transmitter Input ) Item Symbols Min Typ Max Unit Frequency /Tc MHz Clock High Time T6 5 ns Low Time T7 5 ns Data Setup time Hold time T8 T9 4 4 ns ns Data Enable Setup Time Tes 4 ns Frame Period Ty lines ms Vertical Display Period Tyd 24 lines One line Scanning Period T clocks Horizontal Display Period T clocks SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 4 OF 29 25CO(3/3) A4(2 X 297)

15 TFT LCD PRODUCT LVDS Rx Interface Timing Parameter The specification of the LVDS Rx interface timing parameter is shown in Table 4. <Table 4. LVDS Rx Interface Timing Specification> Item Symbol Min Typ Max Unit Remark CLKIN Period trcip msec CLK Difference tcdiff trcip*(3/7) +trcip*(3/7) nsec Input Data trip nsec Input Data trip tricp/7.4 tricp/7 tricp/7+.4 nsec Input Data 2 trip6 2 tricp/7.4 2 tricp/7 2 tricp/7+.4 nsec Input Data 3 trip5 3 tricp/7.4 3 tricp/7 3 tricp/7+.4 nsec Input Data 4 trip4 4 tricp/7.4 4 tricp/7 4 tricp/7+.4 nsec Input Data 5 trip3 5 tricp/7.4 5 tricp/7 5 tricp/7+.4 nsec Input Data 6 trip2 6 tricp/7.4 6 tricp/7 6 tricp/7+.4 nsec trip3 trip4 trip5 trip6 trip trip2 RXO/Ez +/ * Z =,, 2,3 trip Rx3 Rx2 Rx Rx Rx6 Rx5 Rx4 Rx3 Rx2 Rx Rx RxOCLKIN+ Vdiff=[v] trcip Vdiff=[v] RxECLKIN+ tcdiff * Vdiff = (RXO/Ez+)(RXO/Ez),.,(RXO/ECLK+)(RXO/ECLK) SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 5 OF 29 25CO(3/3) A4(2 X 297)

16 TFT LCD PRODUCT SIGNAL TIMING WAVEFORMS OF INTERFACE SIGNAL 7. Sync Timing Waveforms VSync Over 3 Hsync HSync DE Fix HSync width Area ) Need over 3 Hsync during VSync Low 2) Fix HSync width from VSync falling edge to first rising edge 7.2 Horizontal Timing Waveforms Tv Tvd MCLK Th DE R7 ~ R G7 ~ G 7 ~ Invalid Data x, x,2 x,y x,24 Invalid Data x+, SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 6 OF 29 25CO(3/3) A4(2 X 297)

17 TFT LCD PRODUCT Horizontal Timing Waveforms Thd Th MCLK Tc DE RA7 ~RA GA7 ~GA A7 ~A D D2 Dn D638 D639 D64 Invalid Data D D2 D3 Tch Tcl MCLK.5V 2.V.8V Tds Tdh Data Valid Data 2.V.8V Tes DE 2.V SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 7 OF 29 25CO(3/3) A4(2 X 297)

18 25CO(3/3) A4(2 X 297) SPEC. NUMER S86422 SPEC. TITLE HT9E Product Specification TFT LCD PRODUCT 8 OF INPUT SIGNALS, ASIC DISPLAY COLORS & GRAY SCALE OF COLORS Green righter Darker lack Gray Scale of GREEN lue righter Darker lack Gray Scale of LUE White Yellow Magenta Red Cyan Green lue lack asic Colors Red righter Darker lack Gray Scale of RED Darker righter White G5 G4 G3 G2 G G G6 R3 R4 R5 R6 R R2 R 7 G7 R7 lack Gray Scale of WHITE LUE DATA GREEN DATA RED DATA Color & Gray Scale

19 TFT LCD PRODUCT POWER SEQUENCE To prevent a latchup or DC operation of the LCD module, the power on/off sequence shall be as shown in below Power Supply.9VDD.VDD V T T2.9VDD T5.VDD T6 Interface Signal V Valid T3 T4 ack light V T ms T2 5 ms 2ms T3 2ms T4 T5 5ms sec T6 Notes:. When the power supply VDD is V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. ack Light must be turn on after power for logic and interface signal are valid. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 9 OF 29 25CO(3/3) A4(2 X 297)

20 TFT LCD PRODUCT. MECHANICAL CHARACTERISTICS. Dimensional Requirements FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT9E. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters> Parameter Dimensional outline Weight Active area Pixel pitch Number of pixels acklight Specification (max.) (H) * 3.6(V).294(H).294(V) 28(H) 24(V) ( pixel = R + G + dots) Top / ottom edge side 4CCFL type Unit mm gram mm mm pixels.2 Mounting See FIGURE 5. (shown in Appendix).3 AntiGlare and Polarizer Hardness. The surface of the LCD has an antiglare coating to minimize reflection and a coating to reduce scratching..4 Light Leakage There shall not be visible light from the backlighting system around the edges of the screen as seen from a distance 5cm from the screen with an overhead light level of 35lux. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 2 OF 29 25CO(3/3) A4(2 X 297)

21 . RELIALITY TEST TFT LCD PRODUCT The Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters > No Low temperature operation test Thermal shock Vibration test (nonoperating) Test Items High temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Conditions Ta = 6, 24 hrs Ta = 2, 24 hrs Ta = 5, 8%RH, 24hrs Ta = 5, 24hrs Ta =, 24hrs Ta = 2 6 (.5 hr), cycle Frequency Gravity / AMP Period ~ 3 Hz, Sweep rate 3 min.5 G ±X, ±Y, ±Z 3 min Gravity Shock test 8 Pulse width (nonoperating) 5G msec, sine wave Direction ±X, ±Y, ±Z Once for each 9 Electrostatic discharge test (nonoperating) Air : 5 pf, 33Ω, 5 KV Contact : 5 pf, 33Ω, 8 KV SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 2 OF 29 25CO(3/3) A4(2 X 297)

22 TFT LCD PRODUCT HANDLING & CAUTIONS () Cautions when taking out the module Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. As the LCD panel and back light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. Do not pull the interface connector in or out while the LCD module is operating. Put the module display side down on a flat horizontal plane. Handle connectors and cables with care. (3) Cautions for the operation When the module is operating, do not lose CLK, ENA signals. If any one of these signals is lost, the LCD panel would be damaged. Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere Dew drop atmosphere should be avoided. Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electroconductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics Do not apply fixed pattern data signal to the LCD module at product aging. Applying fixed pattern for a long time may cause image sticking. (6) Other cautions Do not disassemble and/or reassemble LCD module. Do not readjust variable resistor or switch etc. When returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 22 OF 29 25CO(3/3) A4(2 X 297)

23 TFT LCD PRODUCT PRODUCT SERIAL NUMER SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 23 OF 29 25CO(3/3) A4(2 X 297)

24 TFT LCD PRODUCT Packing 4. Packing Order Put Pad into the box. Put silica gels in the box. After sealing the box, attach Packing Label on the attach position sign area of the box. Place a cover on the top of the box. As shown in the figure, place the Modules bundled by shielding bag in the box. SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 24 OF 29 25CO(3/3) A4(2 X 297)

25 TFT LCD PRODUCT Packing Note ox Dimension : 346mm(W) 526mm(D) 448mm(H) Package Quantity in one ox : 7pcs 4.3 ox label Label Size : 8 mm (L) 56 mm (W) Contents Model : HT9E Q`ty : Module Q`ty in one box Serial No. : ox Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of Product HT9E ### Type Grade Line Year Month ITEMCODE Serial_no FG CODE SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 25 OF 29 25CO(3/3) A4(2 X 297)

26 TFT LCD PRODUCT APPENDIX Figure. Measurement Set Up (L = 5cm ) Figure 2. White Luminance and Uniformity Measurement Locations (5 points) SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 26 OF 29 25CO(3/3) A4(2 X 297)

27 TFT LCD PRODUCT Figure 3. Response Time Testing Display data White(TFT OFF) lack(tft ON) White(TFT OFF) Optical Response % 9% TR TF % % Time Figure 4. Cross Modulation Test Description VIEW AREA VIEW AREA L3 32,256 96,256 Y (2, 52) 32,768 96,768 Y A (2,52) L Y Y CrossTalk (%) = A Y A Where: Y A = Initial luminance of measured area (cd/m 2 ) Y = Subsequent luminance of measured area (cd/m 2 ) The location measured will be exactly the same in both patterns SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 27 OF 29 25CO(3/3) A4(2 X 297)

28 TFT LCD PRODUCT Figure 5. TFTLCD Module Outline Dimensions (Front view) SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 28 OF 29 25CO(3/3) A4(2 X 297)

29 TFT LCD PRODUCT Figure 6. TFTLCD Module Outline Dimensions (Rear view) SPEC. NUMER SPEC. TITLE S86422 HT9E Product Specification 29 OF 29 25CO(3/3) A4(2 X 297)