/16. Lionel Double Signal Bridge Owner s Manual

Transcription

1 /16 Lionel Double Signal Bridge Owner s Manual

2 Congratulations! Congratulations on your purchase of the Plug-Expand-Play Double Track Signal Bridge! This accessory will provide years of reliable operation. This accessory is now equipped with low voltage LED s and designed to draw as little power as possible. This accessory is also compatible with both AC and DC power! Also included is the Lionel Plug-Expand-Play system, so installation has never been easier! Table of contents Installing the Double Track Signal Bridge 3 Connecting the Signal Bridge to FasTrack 3-4 Connecting the Signal Bridge to Tubular Track 5 Connecting the Signal Bridge to 153IR Controllers 6 Lamp Replacement 7 Limited Warranty/Lionel Service 8 Plug-Expand-Play This revolutionary accessory system simplifies the setup and operation of your favorite accessories. Plug-Expand-Play accessories easily connect to your layout for power using a standardized 3-pin cable that connects directly to a Plug- Expand-Play Lock-on track section. There are separate-sale cables that allow you to expand your system to meet your needs. The following Lionel marks are used throughout this Owner s Manual and are protected under law. All rights reserved. Lionel, LionChief, LionChief Plus,TMCC, LEGACY, FasTrack, TrainMaster, Odyssey, RailSounds, CrewTalk, TowerCom, DynaChuff, StationSounds, Pullmor, ElectroCoupler, Magne-Traction, CAB-1 Remote Controller, American Flyer, Lionel ZW, ZW, MagniVision, TMCC, Lionelville, Wireless Tether, Powerhouse, LionMaster, Conventional Classics, Postwar Celebration Series, TruRail, PH-1 Powerhouse, Powermaster, Powerstation-Powerhouse, Accessory Motor Controller, AMC, Accessory Switch Controller, ASC, Action Recorder Controller, ARC, Track Power Controller 300, TPC 300, Track Power Controller 400, TPC 400, Block Power Controller, BPC, Operating Track Controller, OTC, FatBoy, Lionel Lines, Joshua Lionel Cowen Series, Lockon, TrainSounds, MultiHorn, MultiWhistle, Choo-Choo, SensorTrack, Plug-Expand-Play, Imagineering, SensorCar, LionScale 2

3 Installing the Double Track Signal Bridge The Double Track Signal Bridge is designed to stand up on its own without any mounting hardware. There is, however, a mounting hole provided in both bases of the signal should you decide to permanently mount it to your layout. Connecting the Signal Bridge to FasTrack Using Plug-Expand-Play For simple operation with the Plug-Expand-Play system you will need two pieces of the Plug Expand Play FasTrack Accessory Activator Track Pack (sold separately). The instructions below illustrate how to connect the Signal Bridge to this special section of track. Simply repeat these steps to connect the signal to two independent insulated sections. Once you have oriented the two 5 insulated tracks properly simply insert the Plug- Expand-Play cable into the lock on track. When power is applied the green LED on the signal bridge will illuminate. When the train enters the insulated block section the green LED will turn off and the red LED will illuminate. The red LED will stay illuminated until the last car in the train leaves the insulated block. At which time the red LED will turn off and the green LED will turn on. Note If you wish to extend the length of your insulated detection block you can additional 10 sections of Accessory Activator Extender sections (sold separately). Place these sections in between the two 5 insulated straight sections. Signal Bridge 3-pin male connector 5" track with break Lock-on FasTrack Break 10" track 5" track with break Break FasTrack Figure 1. Connecting the signal bridge to Plug-Expand-Play Activator Track Packs 3

4 Connecting the Signal Bridge to FasTrack continued Using Standard FasTrack Wiring You can clip off the Plug-Expand-Play connector on the end of the cable OR purchase two Plug-Expand-Play 8" Female cables (sold separately). The is also available through Lionel Customer Service under part number You will also need two of the FasTrack Accessory Activation Packs ( , sold separately). The red wire connects to either the center rail of the track OR the A terminal on an accessory transformer (the accessory transformer must be in phase with the track power supply). If you use a DC power supply the red wire MUST connect to the positive DC rail or terminal (most commonly the center rail). The black wire connects to the grounded outside rail of the track OR the U terminal on an accessory transformer (the accessory transformer must be in phase with the track power supply). If you use a DC power supply the black wire MUST connect to the negative DC rail or terminal (most commonly the outside rail). The white wire connects to the insulated outside rail of the track. When a train is present on the insulated track the LED s will change from an illuminated green LED to an illuminated red LED. Once the train leaves the insulated block the red LED will turn off and the green LED will illuminate again. 3-pin male connector 3-pin female connnector Signal Bridge 8" 3-pin female pigtail ( ) 5" track with break 10" track FasTrack Break 5" track with break Break FasTrack Figure 2. Connecting the signal bridge to FasTrack 4 Note Connections are made underneath the 10" section of track.

5 Connecting the Signal Bridge to Tubular Track You can clip off the Plug-Expand-Play connector on the end of the cable OR purchase two PEP 8 Female cables (sold separately). The is also available through Lionel Customer Service under part number Regardless of the direction you take the wiring is quite simple. If you are using O gauge tubular track you will need two O Gauge Insulated Tracks (sold separately). If you are using O27 Tubular track you will need two O27 Gauge Insulated Tracks (sold separately). Follow the diagram if you choose to connect your signal to the track using CTC Lockons, otherwise continue follow the instructions below; Connect the red wire to either the center rail of the track you are connecting the signal to OR to constant voltage accessory power (hot; A, B, C or D). Connect the black wire to the non-insulated outside rail OR to constant voltage accessory power (ground; U). The white wire connects to the insulated outside rail (isolated ground). Signal Bridge (O gauge insulated track) OR (O27 gauge insulated track) CTC lock-on 10" Tubular track 10" Tubular track Insulating pin CTC lock-on Insulating pin 3-pin male connector 3-pin female connnector 8" 3-pin female pigtail ( ) Figure 3. Connecting the signal bridge to tubular track 5

6 Connecting the Signal Bridge to 153IR Controllers You can clip off the Plug-Expand-Play connector on the end of the cable OR purchase two PEP 8 Female cables (sold separately). The is also available through Lionel Customer Service under part number Regardless of the direction you take the wiring is quite simple. Signal Bridge 3-pin male connector 3-pin female connnector 8" 3-pin female pigtail ( ) ACC ACC POWER GROUND NO NC ACC ACC POWER GROUND NO NC Figure 4. Connecting the signal bridge to 153IR controllers 6

7 Lamp Replacement Your Signal Bridge is equipped with LED s which should last the life of the product. In the event you need to replace the LED on your Signal Bridge please contact Lionel Customer Service at ext 2, Monday through Friday 9am to 5pm EDT. 7

8 Lionel Limited Warranty Policy & Service his Lionel product, including all mechanical and electrical components, moving parts, motors and structural components, with the exception of LIGHT BULBS, TLED s & TRACTION TIRES are warranted to the original owner-purchaser for a period of one year from the original date of purchase against original defects in materials or workmanship when purchased through a Lionel Authorized Retailer*. This warranty does NOT cover the following: Normal wear and tear Light bulbs or LED s Defects appearing in the course of commercial use Damage resulting from abuse/misuse of the product Transfer of this product by the original owner-purchaser to another person voids this warranty in its entirety. Modification of this product in any way; visually, mechanically or electronically, voids the warranty in its entirety. Any warranted product which is defective in original materials or workmanship and is delivered by the original owner-purchaser (this warranty is nontransferrable) to Lionel LLC or any Lionel Authorized Service Station MUST be accompanied by the original receipt for purchase (or copy) from an Authorized Lionel Retailer*, will at the discretion of Lionel LLC, be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a suitable replacement is not available, Lionel will offer to replace the product with a comparable model (determined by Lionel LLC), if available. In the event a comparable model is not available the customer will be refunded the original purchase price (requires proof of purchase from the Authorized Lionel Retailer* it was originally purchased). Any products on which warranty service is sought must be sent freight or postage prepaid (Lionel will refuse any package when postage is due). Transportation and shipping charges are not covered as part of this warranty. NOTE: Products that require service that do not have a receipt from an LIONEL AUTHORIZED RETAILER* will be required to pay for all parts required to repair the product (labor will not incur a charge) providing the product is not older than 3 years from date of manufacture and is within 1 year from date of purchase. A copy of the original sales receipt is required. In no event shall Lionel LLC be held liable for incidental or consequential damages. ome states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you Sspecific legal rights and you may have other rights which vary from state to state. Instructions for Obtaining Service f service for this Lionel LLC product is required; bring the item, along with your DATED sales receipt and completed warranty information (at the bottom of this Ipage) to the nearest Lionel Authorized Service Station. Your nearest Lionel Service Station can be found by calling LIONEL or by accessing the website at If you prefer to send your Lionel product directly to Lionel, for repair you must FIRST call extension 2 or write to Lionel Customer Service, 6000 Victory Lane, Concord, NC Please have the 6-digit Lionel product number, the date of original purchase, the dealer where the item was purchased and what seems to be the problem. You will receive a return authorization (RA) number to ensure your merchandise will be properly tracked and handled upon receipt at Lionel LLC. Once you have your Return Authorization (RA) number, make sure the item is packed in its original Styrofoam inner container which is placed inside the original outer display box (this will help prevent damage during shipping and handling). This shipment MUST be prepaid and we recommend that it be insured with the carrier of your choice. Please make sure you have followed all of the above instructions carefully before returning any merchandise for service. You may choose to have your product repaired by one of Lionel LLC s Authorized Service Stations after its warranty has expired. A reasonable service fee should be expected once the product warranty has expired. Warranty Information lease complete the information below and keep it, along with your DATED ORIGINAL SALES RECEIPT. You MUST present this form AND your DATED PSALES RECEIPT when requesting warranty service. *A complete listing of Lionel Authorized retailers can be found by calling LIONEL or by visiting our website at Products that are more than 3 years old, from date of manufacture, are not applicable for warranty coverage, even if they have never been sold prior to this date. (Under no circumstance shall any components or labor be provided free of charge.) Name Address Place of Purchase Date of Purchase Product Number 2016 LIONEL L.L.C Performance Dr., CONCORD, NC UNITED STATES OF AMERICA PRINTED IN CHINA