VIRTUAL INTERACTIVE BOARD SYSTEM VGB-1000R/ MS-VGB1K. Instruction manual

Transcription

1 VIRTUAL INTERACTIVE BOARD SYSTEM VGB-1000R/ MS-VGB1K Instruction manual

2 Table of Contents FCC COMPLIANCE STATEMENT... 4 WARNINGS AND PRECAUTIONS... 4 WARRANTY... 5 STANDARD WARRANTY... 5 THREE YEAR WARRANTY... 5 DISPOSAL INTRODUCTION SYSTEM DIAGRAM MAT-5 PLASTIC MAT QUICK CALIBRATION GUIDE MS-VGB1K MOBILE VGB REAR PANEL RP-77 Rear Panel PD-2A Power Center FRONT PANEL DVK-300HD HD/SD Chromakey NVS-25 H.264 Network Video Streaming Server AD-100M Audio Delay Box HDR-70 HD/SD Digital Video Recorder DIMENSIONS FS-210 FOOT SWITCH CONNECTORS IEPEN INTERACTIVE ELECTRONIC PEN LBK-1 LOOK BACK KIT FEATURES TALLY LED AND INPUT PHONE JACK PARTS LIST AND LOOK BACK KIT EXPLODED VIEW LBK-1 LOOK BACK KIT EXPLODED VIEW LBK1-1-1 Main Support Exploded View LBK Monitor and LCD Display Mount LBK Glass Frame Module and Hood Support Wire LBK1-2 Exploded View of Main Support, Glass Frame, LCD Display and Tripod LBK1-3 Look Back Kit Assembly DIMENSIONS SPECIFICATIONS QUICK SETUP DVK-300HD HD/SD CHROMAKEY ALPHA MATTE PREVIEW OUTPUT NVS-25 VIDEO STREAMING SERVER AUDIO SETTING SPECIFICATIONS SERVICE AND SUPPORT

3 Disclaimer of Product & Services The information offered in this instruction manual is intended as a guide only. At all times, Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. Datavideo Technologies always recommend that you double check the information in this document for accuracy before making any purchase decision or using the product. Datavideo Technologies is not responsible for any omissions or errors, or for any subsequent loss or damage caused by using the information contained within this manual. Further advice on the content of this manual or on the product can be obtained by contacting your local Datavideo Office or dealer. 3

4 FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit should not be placed in a built-in installation unless proper ventilation is provided. 7. This product should only be operated from the type of power source indicated on the marking label of the AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. 8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed. 9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension cord rating. 10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed 15 amperes. 11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill liquid of any kind onto or into this unit. 12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself. Opening or removing covers that are marked Do Not Remove may expose you to dangerous voltage points or other risks, and will void your warranty. Refer all service issues to qualified service personnel. 13. Unplug this product from the wall outlet and refer to qualified service personnel under the following conditions: a. When the power cord is damaged or frayed; b. When liquid has spilled into the unit; c. When the product has been exposed to rain or water; d. When the product does not operate normally under normal operating conditions. Adjust only those controls that are covered by the operating instructions in this manual; improper adjustment of other controls may result in damage to the unit and may often require extensive work by a qualified technician to restore the unit to normal operation; 4

5 e. When the product has been dropped or the cabinet has been damaged; f. When the product exhibits a distinct change in performance, indicating a need for service. Warranty Standard Warranty Datavideo equipment are guaranteed against any manufacturing defects for one year from the date of purchase. The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. The product warranty period begins on the purchase date. If the purchase date is unknown, the product warranty period begins on the thirtieth day after shipment from a Datavideo office. All non-datavideo manufactured products (product without Datavideo logo) have only one year warranty from the date of purchase. Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered under warranty. Viruses and malware infections on the computer systems are not covered under warranty. Any errors that are caused by unauthorized third-party software installations, which are not required by our computer systems, are not covered under warranty. All mail or transportation costs including insurance are at the expense of the owner. All other claims of any nature are not covered. All accessories including headphones, cables, and batteries are not covered under warranty. Warranty only valid in the country or region of purchase. Your statutory rights are not affected. Three Year Warranty All Datavideo products purchased after July 1st, 2017 are qualified for a free two years extension to the standard warranty, providing the product is registered with Datavideo within 30 days of purchase. Certain parts with limited lifetime expectancy such as LCD panels, DVD drives, Hard Drive, Solid State Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe Card are covered for 1 year. The three-year warranty must be registered on Datavideo's official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase. 5

6 Disposal For EU Customers only - WEEE Marking This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. CE Marking is the symbol as shown on the left of this page. The letters "CE" are the abbreviation of French phrase "Conformité Européene" which literally means "European Conformity". The term initially used was "EC Mark" and it was officially replaced by "CE Marking" in the Directive 93/68/EEC in "CE Marking" is now used in all EU official documents. 6

7 1. Introduction VGB-1000R Virtual Interactive Board System is designed specifically for Massive Open Online Course, news report at TV station and stock analysis. The system is an integration of features for video shooting, display of external PowerPoint slides, chroma keying and recording. With the VGB-1000R, you no longer need a team to do video recording, the VGB- 1000R allows you to achieve premium quality video recording by one man without the need for a big studio space. VGB-1000R Virtual Interactive Board System is innovated by Datavideo. The system is designed using the rear projection technique and projects PowerPoint slides or video onto a special green backdrop via a short throw projector. The screen can be as large as 120 inches. The interactive electronic pen (IEPEN) can be wirelessly linked to the system, thus allowing the speaker to make remarks on the screen while explaining the lecture content to students. In addition, the VGB-1000R Virtual Interactive Board System is easy to use and its Look Back Design allows you to easily view the recording. Streaming and recording can be done at the same time. Furthermore, you can turn any place into a professional studio room with the assembled RPK-1 Rear Projection Kit, so that you can create professional programs anytime anywhere. Note: External peripheral devices such as Look Back Kit, Projector, Green Screen, HDMI/SDI monior, Microphones, PC/Laptop, Camera, Tripod, and Cables are not included in the VGB-1000R package. 7

8 1.1 System Diagram Virtual Interactive Board System (VGB-1000R) - Rear Projection 8

9 2. MAT-5 Plastic MAT The MAT-Series plastic clothes for chroma keying are coated with water and stain repellents. Its non-reflective coating provides premium chroma key quality. Model Name MAT-5 Product Name Green Color Plastic MAT (1.8M x 54M) for wall use Color Green Size W (m) x L (m): 1.8 x 54 Thickness 0.35 mm 3. Quick Calibration Guide Before start using the VGB-1000R system, the MS-VGB1K must be calibrated using the following steps. 1. Locate AC inlet at the back of MS-VGB1K and connect it to the wall socket using a power cord. 2. Press the power button on the left of the AC inlet to turn on MS-VGB1K. 3. Plug the FS-210 footswitch into the GPI port on the RP-77 rear panel. 4. Turn on the notebook computer and connect the projector to the computer: For notebook equipped with HDMI port only, use an HDMI splitter to connect the notebook to the BACKGROUND HDMI IN port located on the rear panel of the MS- VGB1K and the projector. For notebook equipped with an HDMI port and a VGA port, connect the HDMI port to the BACKGROUND HDMI IN port located on the rear panel of the MS-VGB1K and the VGA port to the projector. 5. Open the calibration graph below on the notebook and switch to full screen mode. 6. Project the calibration graph onto the green board and then adjust the height of the camera installed on the LBK-1 Look Back Kit such that the camera lens is exactly at the same height as the center circle of the calibration graph. 9

10 7. Connect an SDI monitor to the PGM_REC_SDI OUT port. 8. Turn on the monitor until you see the calibration graph, which is the same graph that is projected onto the green board. 9. Next, on the green board, locate the four edge center points indicated by the four arrows as shown below and make sure they lie on the corresponding edges of the green board. 10. Use the camera (LBK-1) zoom function to make sure the four corners of the monitor correspond to the four corners of the green board. 10

11 11. Attach the ebeam receiver to the left of the board as shown in the diagram below and connect the receiver to the notebook by a USB cable. 12. Install the ebeam software on the notebook computer. 13. To calibrate the system, launch the ebeam software and press the circular button located at the center of the receiver once. 11

12 14. Once the calibration chart shown below appears on the green board, use the Interactive Electronic Pen to lightly touch the nine calibration marks one by one starting from the one located at the top left hand corner of the chart and then move down the column in a zig-zag fashion. 15. After the ninth calibration mark is touched, the calibration chart will disappear and return to the projected computer screen. 16. On the green board, locate the tools palette as shown below. 17. The user is allowed to turn on and off the tools palette by pressing the yellow circular button on the Interactive Electronic Pen. 12

13 18. After the system is successfully calibrated, insert the hard disk into the HDR-70 High Definition SD Digital Video Recorder and then turn the latch left to lock the inserted hard disk. 19. Step on the footswitch once to enter the HDR-70 Recorder into the Standby mode, 20. Step on the footswitch again to start recording. 21. After recording is complete, step on the footswitch once to return to the standby mode. 22. Finally, remove the hard disk for post-editing. 4. MS-VGB1K Mobile VGB The MS-VGB1K Mobile VGB is a main Audio and Video processing unit for Virtual Interactive Board System (VGB-1000R). It is an integrated system of HD/SD Chromakeyer, HD/SD Digital Video Recorder, Audio Delay Box, H.264 Network Video Streaming Server, Power Center, and Foot Switch, which are all housed in a 4U Rack Mount Kit. An I/O Panel is provided on the back of the unit. On the MS-VGB1K Mobile VGB System, the Chromakeyer combines foreground and background videos with the audio signals, which are captured by the microphone and sent from the RCA LINE-IN located on the back of the Audio Delay Box (AD-100M). The HD/SD Digital Video Recorder then embeds the audio into the recorded video and the Network Video Streaming Server provides live streaming of the final program. On the I/O Panel, there are different input and output interfaces available for connections to external devices such as LBK-1 look Back Kit, Video Splitter, HDMI/SDI monitor, FS-210 Foot Swtich, Micropphone, and PC/Laptop. The handles installed on two sides of the Rack Mount Kit provide easy system mobility. 4.1 Rear Panel 13

14 RP-77 Rear Panel Foreground SDI/HDMI IN Connect one of SDI IN or HDMI IN to the camera shooting foreground talent. Background HDMI IN Connect this port to an output port of a 2~4 port HDMI Splitter. Connect another HDMI output of the HDMI splitter to the Projector. The input port of the HDMI splitter is connected to the HDMI port of the user s NB/PC, which is the source of PPT files. Note: The status of this port is indicated by the DVI LED located on the front panel of the DVK-300HD HD/SD Chromakeyer. AUDIO IN (R)/(L) Connect the RCA AUDIO IN either to a PC (PPT Audio) or to a player as background sound. 14

15 MIC IN Connect this port to an external microphone. Note: At the back panel of AD-100M as shown in the diagram below, select the correct 48V Phantom power for Condenser Microphone or 48V off for Dynamic Microphone before use. Please avoid switching the mode to MIC OFF as it cuts off the MIC connection. In addition, the available MIC GAIN Levels are 60, 40 and 20 db. Please refer to AD-100M instruction manual for details. Figure 1: AD-100M Rear Panel GPI Connect this port to FS-210 foot switch which sends tally light signal to the LBK-1 and toggles record/pause on the HDR-70. Note: Before use, the HDD has to be inserted into the HDR-70 and the record mode button on the HDR-70 must be ON. Please refer to HDR-70 instruction manual for in-depth operation instructions. CHROMA Control LAN Connect this port to a PC/NB with the DVK- 300HD software installed to apply the Chroma key effect to the foreground camera video. Please refer to DVK-300HD instruction manual for in-depth operation instructions. 15

16 PGM _REC_SDI OUT Connect this port to an SDI monitor, which displays the recorded video/audio on the HDR-70 during playback. Note: Please make sure the Record Mode button is enabled when this port is used. DVK-300HD HDMI OUT Connect this port to the monitor on the LBK-1 Look Back Kit and this connection allows the talent to view his/her image by looking into the LBK-1 mirror, which is basically the reflected screen image of the monitor connected to this port. PGM_REC HDMI OUT Connect this port to an HDMI monitor, which displays the recorded video/audio on the HDR-70 during playback. Note: Please make sure the Record Mode button is enabled when this port is used. STREAMING LAN OUT Connect this port to a Router/Switch to stream Video and Audio from the NVS-25. Please refer to NVS-25 instruction manual for in-depth operation instructions. PD-2A Power Center On / Off Switch Turns the PD-2A On / Off when using AC Power. Note: No function when DC Power is used. 16

17 AC IN with built-in fuse AC Inlet for connecting to suitable mains power outlet ( VAC). The socket contains a fuse holder fitted with a 6.3A fuse. Cooling Fan The PD-2A has three built-in cooling fans, which must not be blocked so as to allow sufficient airflow. Note: The two leftmost fans will start to operate when the ambient temperature reaches approximately 50 C.The rightmost fan will start to operate when the ambient temperature reaches approximately 70 C. DC OUTPUT LED No. 1~7 XLR DC Output LED indicators Indicator is ON during normal operation and OFF in the event of overload or fault. 4.2 Front Panel DVK-300HD HD/SD Chromakey 17

18 Power Switch Switches DVK-300HD On/Off Input Source Indicators CAMERA IN Camera Source Input Indicators (SDI / HDMI) BACKGROUND IN Background Input Indicators (SDI / DVI) Note: The DVI LED indicator corresponds to the status of the BACKGROUND HDMI IN port and will be turned ON upon connection. NVS-25 H.264 Network Video Streaming Server Power On/Off Switch Switches the power On / Off USB USB 2.0 interface for connecting external storage Mode Select Mode Button - Select Input source between CVBS / SDI / HDMI. REC LED indicates the recording status STM LED indicates the stream server status PWR LED indicates the power status 18

19 RECORD Turns ON/OFF the recording feature STM Turns ON/OFF the network streaming feature Note: Before using this button, the user should first make sure the network and stream settings are properly configured. Restore factory defaults from the front panel. From power off, press and hold the STM button and turn on the NVS-25 power; keep holding the STM button for 40 seconds. When released, the NVS-25 will take a further 30 seconds to finish the boot-up process. AD-100M Audio Delay Box Power ON/OFF Switch Switches the power ON/OFF Menu This switch allows access to the 9 mode system settings. Mode Select LEVEL or TIME information on LCD Display. LEVEL displays the audio output level in dbu. TIME displays the AUDIO DELAY & ATTENUATION settings. 19

20 Adjust The ADJUST knob is for mode select and value adjustment. It can be rotated to navigate through menu options or parameter values and then pressed in to select or confirm a chosen value. HDR-70 HD/SD Digital Video Recorder Power On / Off Button This is a soft power on / off button which powers the unit on from standby; the main power on / off switch is on the rear. Display Panel Shows bin number, time code, audio meters or the Menu Display. Menu Button This brings up the menu display which is navigated using the Previous / Next Buttons. Note1: In play state, press MENU button, the display panel will show the information of the playing file. Note2: In record state, press MENU button, display panel will show the information of recording file. Fwd / Rew Buttons In playback state, these buttons will operate as Fast Forward and Rewind Buttons. While the unit is playing, press Fwd or Rew button and then press Previous / Next Buttons which if pressed multiple times, HDR-70 will fast play forward or rewind in x1, x3, x6, x9, and x12. 20

21 Record Mode Button When you want to record press the Record Mode button first. This button must also be enabled if PGM_REC_SDI OUT and PGM_REC HDMI OUT ports are used. In Record Mode (Record Mode button LED on), press play button, and the HDR- 70 must perform file conversion internally first before entering the PLAY state so please wait for 3 to 5 seconds. In Play Mode (Record Mode button LED off), press play button, and the HDR-70 will enter the PLAY state, so that the HDR-70 can play the file immediately. Note: When playing file in Record Mode, if the SDI source signal is lost, the video and audio of the file being played will not be synchronized, thus please play file in the Play Mode. Previous / Next Buttons Navigate up and down the recorded bins and menu options. Record Button To start recording, press the Record Button and Play Button simultaneously. Note1: Unit will not record if no video signal is present. Note2: In PLAY state, press Record button, the display panel will show CH1-4 audio meters; press Record button again, the panel will show CH5-8 audio meters. 21

22 Play / Pause Button Starts playback of a bin, or pauses playback of a bin status will be displayed on the Display Panel. Note1: In PLAY state, press and hold PLAY button and then press Fwd or Rew button to skip 8 seconds of the clip. Note2: In PAUSE state, press and hold PAUSE button and then press Fwd or Rew button to skip to the next or previous clip. Stop Button In stop state, press and hold PLAY button for 4 seconds and then release PLAY button, HDR-70 will play the last 15 seconds of a bin. Audio Input Level LEDs The Audio Input Level LEDs show the audio input levels of the incoming source. Audio IN and Volume Control Stereo mini jack for stereo headphone plug. Audio Volume Adjustment knob allows you to adjust the headphone volume. GEN-LOCK LED LED will be ON when signal is GEN- LOCKed. 2.5 Removable HDD Rack 2.5" Removable HDD Rack, and SATA & USB interface can be connected to PC for file transfer. 22

23 4.3 Dimensions MS-VGB1K All measurements in millimeter (mm) 23

24 5. FS-210 Foot Switch The FS-210 is a Foot Switch designed specifically for use with the MS-VGB1K. The purpose is to allow the user to toggle between Record and Record Pause modes on the HDR-70 HD/SD Digital Video Recorder by simply stepping on the pedal. The mode that the recorder is currently in is indicated by the Tally Light on the LBK-1 Look Back Kit. In the Record Mode, the tally light displays red color; on the contrary, if the recorder is in the record pause mode, the tally light will be OFF. There are two connectors on the FS-210 cable end. The Mini-XLR is connected to the GPI port on the HDR-70 HD/SD Digital Video Recorder and the 3.5mm ear phone connector is plugged into the LBK-1 Tally Light IN. Note: The LBK-1 Look Back Kit is not included in the VGB-1000R product package. 5.1 Connectors Mini XLR Connect to GPI port (HDR-70 HD/SD Digital Video Recorder) 3.5mm Phone Connector Connect to Tally Input (LBK-1 Look Back Kit) 24

25 6. IEPEN Interactive Electronic Pen In order to allow the speaker to make remarks on the screen while explaining the lecture content to students, the interactive electronic pen (IEPEN) must be connected wirelessly to the receiver that can magnetically be attached to the whiteboard. The interactive electronic pen and the receiver are shown in the diagram below. Weight Dimensions Battery Type Battery Life 0.8 oz (23 g) not including weight of battery 5.55 x 0.75 x 0.6 inches (143 x 20 x 15 mm) AAA alkaline 50 hours 25

26 7. LBK-1 Look Back Kit The LBK-1 Look Back Kit can be used in any Camera Setup. The kit contains a look back mirror, which allows the user or talent to view his/her mirrored image reflected off from a 22 monitor connected to the Virtual Interactive Board System (MS-VGB1K). Therefore, the LBK-1 can be used as a part of total VGB-1000R solution by mounting it to the tripod mount quick release system. 7.1 Features Allows mounting of a 22 monitor with 16:9 aspect ratio and four 100x100mm VESA mount holes (MIS-D/100/C), for example ACER KA220HQ. Large sized mirror installed with a green sticker facing outward. Large hood to cover 2 sides of the mirror. Red Tally Light Adjustable camera mount dock 7.2 Tally LED and Input Phone Jack 26

27 7.3 Parts List and Look Back Kit Exploded View Label Name Parts List Quantity A Main Support Rail 1 B Spacer Block 2 C Screw (Wing Nut 1/4 20UNC 12.5mm Nickel Plated) 4 D Screw (Pan-Head 1/4" 20UNC 12mm Nickel Plated) 2 E Riser Block 1 F Screw (1/4" 20UNC Hex Head 31mm) 4 G Camera Dock Module 1 H 1/4 20UNC Screw 1 I Anti-Collision Rubber Strip 2 J Glass Sheet 1 K Glass Frame Module 1 L Hood Support Wire 1 M LCD Mounting Bracket 1 N Nyloc Screw (ISO Counter Sunk M4*8m/m Black (RoHS)) 4 O Cloth Snood/Hood 1 P Hex Tool 4mm 1 Q Hex Tool 3mm 1 27

28 Look Back Kit Kit Exploded View View Enlargement Ratio 2:1 Enlargement Ratio 2:1 Enlargement Ratio 2:1 Look Back Kit Exploded VIew

29 LBK1-1-1 Main Support Exploded View

30 LBK Monitor and LCD Display Mount

31 LBK Glass Frame Module and Hood Support Wire

32 LBK1-2 Exploded view of Main Support, Glass Frame, LCD Display and Tripod

33 LBK1-3 Look Back Kit Assembly First remove the two screws located at the two ends of the glass frame module (Location B). 2. Insert the glass into the glass frame module above the tripod. 3. Secure the glass with the screws of step Remove the loop strip of the Velcro adhered to the Cloth Hood (Location A1). 5. Adhere the loop strip to the glass frame module (Location A2). 6. Mount the camera to the camera dock module. 7. Finally, attach the hook strip of the cloth hood to the loop strip of the glass frame to complete the assembly.

34 7.4 Dimensions 7.5 Specifications Tally Light Color Red Number 1 Input Interface 3.5mm Phone Jack Dimensions Length mm Width 546 mm Height mm Product Weight Approximately 5 Kg Remarks Not inclusive of Monitor, Camera, Tripod and Quick Release Plate 34

35 Note A: Camera and tripod are not included. Please make sure the tripod is able to sustain 10 Kg load (camera included) or 7 Kg load (camera not included). Note B: 22 16:9 ratio PC monitor and the related cables/converters are not included. Please use a monitor with VESA mount screw holes located at four corners of a 100x100 mm rectangle on the back. The monitor should also be equipped with an HDMI input. If DVI Monitor is used, please make sure the monitor includes a DVI-D/DVI-I input, and an external HDMI to DVI-D converter/cable (Male to Male) which converts an HDMI source (MS-VGB1K) to DVI-D (18+1 pin single link or 24+1 pin dual link depending on the Monitor). Example of a 22 16:9 Monitor is Acer KA220HQ (Ref. Price: US$140). 35

36 8. Quick Setup Before start using your VGB-1000R, there are several settings that must be manually configured. This section will guide you through various specific configurations. 8.1 DVK-300HD HD/SD Chromakey Alpha Matte Preview Output Please make sure the Alpha Matte Preview Output is set to PREVIEW (PVW). 1. On the User Interface, click the Configuration button to open the Advanced config dialogue box. 2. Select the OUTPUTS CONFIGURATION by clicking the CHANGE button on the right. 36

37 3. Select PREVIEW (PVW) and then click the SAVE button to complete the configuration. 8.2 NVS-25 Video Streaming Server Audio Setting The audio source should be set to RCA. Login the NVS-25 User Interface, click Settings -> Encoder Setup. Once in the Encoder Setup page, click the Audio Source pull-down menu and select RCA. After all correct settings are selected, please remember to click the APPLY button so that the new settings will become effective. 37

38 9. Specifications Video Input Chroma Key Control DVK-300HD Foreground DVK-300HD Background DVK-300HD Control HDD Size: 1 x SDI or 1 x HDMI connector on RP-77 SDI Formats: 576i, 480i (SMPTE 259M-C) 1080i50, 1080i59.94,1080i60, 720p50,720p59.94, 720p60, 1080p25, 1080p30 (SMPTE 292M)1080p50, 1080p59.94,1080p60 (SMPTE 425M) HDMI Formats: 480i/576i/720p50/720p59.94/720p60/1080i50/1080i59. 94/1080i60/1080p25/1080p30/1080p50 / 1080p59.94/1080p60 1 x HDMI connector Formats: 480i/576i/480p/576p/720p50/720p59.94/720p60/1080i 50/1080i59.94/1080i60/1080p25/1080p30/1080p50 /1080p59.94/1080p60 LAN / RJ-45 port for PC access on RP-77 HDD: 250/320/500/750 GB SSD: 120/128/240/256/480/512 GB Recording (HDR-70) Recording Video format: CODEC HD 720P@50/59.94/ i@50/59.94/ P@23.976/24 SD 50/59.94 Hz MPEG2 Long GOP: HD 1. 10Mbps 4:2:0 1440x1080/1280x Mbps 4:2:0 1440x1080/1280x Mbps 4:2:2 1920x1080/1280x Mbps 4:2:2 1920x1080/1280x Mbps 4:2:2 1920x1080/1280x Mbps 4:2:2 1920x1080/1280x720 SD 1. 8Mbps 4:2:0 720x480/720x Mbps 4:2:2 720x480/720x Mbps 4:2:2 720x480/720x Mbps 4:2:2 720x480/720x576 38

39 Audio Input (AD-100M) Streaming (NVS-25) Video Output Foot Switch Input Microphone RCA Line-IN OUTPUT Video Encode Supported Resolutions Audio Encode Network Feature DVK-300HD HDMI OUT PGM_REC_OUT 1x mini XLR on RP-77 MPEG2 i-frame Only: HD Mbps 4:2:2 1920x1080/1280x Mbps 4:2:2 1920x1080/1280x720 SD 1. 25Mbps 4:2:2 720x480/720x Mbps 4:2:2 720x480/720x576 1x XLR balanced MIC IN on RP-77 48V on/off, Mic off, Gain 20/40/60 db on AD-100M 2 channels of unbalanced RCA IN on RP-77 1x RJ-45 (10/100M Ethernet) on RP-77 1x USB 2.0 Type A for file output to USB Storage on NVS- 25 H.264 / AVC video CODEC, up to High Profile Level 4.0 Configurable Bit-rate up to 6Mbps 50P / 59.94P / 60P (50P/59.94P/60P input, 25P/30P record/output) 50i / 59.94i / 60i 50P / 59.94P / 60P 576@ 50i, 59.94i AAC-LC audio CODEC Sampling rate:48khz, 16bit Configurable Bit-rate up to 384Kbps DHCP Client Streaming feature: - HLS/RTSP/RTMP Server (One protocol at a time) - Supports up to 3 clients 1x HDMI connector on RP-77, without Audio (To Connect to LBK-1 Look Back Kit) 1x HDMI and 1x SDI on RP-77 with Audio (To connect to HDMI or SDI monitor) 1x FS-210 Foot Switch, connect to Mini XLR on RP-77 and 3.5mm Phone Jack on LBK-1 Note: Please refer to individual instruction manuals of the DVK-300HD, HDR-70, AD-100M, NVS-25, PD-2A, RMK-5 and FS-210 for in-depth operation instructions. 39

40 Service & Support It is our goal to make owning and using Datavideo products a satisfying experience. Our support staff is available to assist you to set up and operate your system. Contact your local office for specific support requests. Plus, please visit to access our FAQ section. China Shanghai Datavideo Technologies China Co 601,Building 10,No.1228, Rd.Jiangchang, Jingan District,Shanghai Tel: Fax: service@datavideo.cn Hong Kong Datavideo Hong Kong Ltd G/F.,26 Cross Lane Wanchai, Hong Kong Tel: Fax: info@datavideo.com.hk Singapore Datavideo Technologies (S) PTE Ltd No. 178 Paya Lebar Road #06-03 Singapore Tel: Fax: sales@datavideo.sg China Beijing Datavideo Technologies China Co No. 812, Building B, Wankai Center, No.316, Wan Feng Road, Fengtai District, Beijing, China Tel: Fax: service@datavideo.cn India Noida Datavideo India Noida A-132, Sec-63,Noida , India Tel: Fax: sales@datavideo.in Taiwan Datavideo Technologies Co. Ltd 10F. No. 176, Jian 1st Rd.,Chung Ho District, New Taipei City 235, Taiwan Tel: Fax: service@datavideo.com.tw China Chengdu Datavideo Technologies China Co B-823,Meinian square,no.1388, Middle of Tianfu Avenue,Gaoxin District, Chengdu,Sichuan Tel: Fax: service@datavideo.cn India Kochi Datavideo India Kochi 2nd Floor- North Wing, Govardhan Building, Opp. NCC Group Headquaters, Chittoor Road, Cochin Tel: Fax: sales@datavideo.in United States Datavideo Corporation 7048 Elmer Avenue. Whittier, CA 90602, U.S.A. Tel: Fax: sales@datavideo.com China Fuzhou Datavideo Technologies China Co A Room,No.8, Aojiang Road, Taijiang District,Fuzhou,Fujian,China Tel: , Fax: service@datavideo.cn Netherlands Datavideo Technologies Europe BV Floridadreef AM Utrecht, The Netherlands Tel: Fax: info@datavideo.nl United Kingdom Datavideo UK Limited Brookfield House, Brookfield Industrial Estate, Peakdale Road, Glossop, Derbyshire, SK13 6LQ Tel: Fax: sales@datavideo.co.uk China Jinan Datavideo Technologies China Co 902, No. 1 business building, Xiangtai Square, No. 129, Yingxiongshan Road, Shizhong District, Jinan City, Shandong Province, China Tel: service@datavideo.cn Singapore Datavideo Visual Technology(S) Pte Ltd No. 178 Paya Lebar Road #06-07 Singapore Tel: Fax: info@datavideovirtualset.com France Datavideo France s.a.r.l. Cité Descartes 1, rue Albert Einstein Champs sur Marne Marne la Vallée cedex 2 Tel: Fax: info@datavideo.fr Please visit our website for latest manual update. All the trademarks are the properties of their respective owners. Datavideo Technologies Co., Ltd. All rights reserved 2018 Jan Version : E2