WM-3004HD. Instruction Manual. ASTRODESIGN, Inc. HD LCD Waveform Monitor. August 25, Ver.1.00

Transcription

1 WM-3004HD HD LCD Waveform Monitor Instruction Manual August 5, 003 Ver..00 ASTRODESIGN, Inc.

2 CTENTS INTRODUCTI 3 SAFETY PRECAUTIS 4 CHAPTER CHAPTER CHAPTER 3 CHAPTER 4 CHAPTER 5 CCERNING THE WM PARTS AND THEIR FUNCTIS 8. WM-3004 front panel view and parts 8. WM-3004 rear panel view and parts 0 OPERATI 3. Connections 3. Usage 3.3 Operation and how to use the switches PICTURE mode PICTURE3 mode WAVEFORM mode VECTOR mode STATUS mode AUDIO mode MENU mode HELP mode Installing and securing the monitor 50 MAIN SPECIFICATIS 5 4. Input formats 5 4. Input signal systems Display system Headphones output Concerning the adjustment values Settings at initialization Common setting items Setting items by channel General specifications Outline drawings 57 STANDARD AND OPTIAL ACCESSORIES Standard accessories Optional accessories 58 NOTICE 59

3 INTRODUCTI Thank you very much for purchasing this model WM-3004 HD LCD waveform monitor. This manual contains details on the operation procedures to be followed when the WM-3004 is used, the checkpoints and precautions to be observed, and so on. Improper handling may result in malfunctioning. Before using the WM-3004, please read through these instructions to ensure that you will operate the monitor correctly. After reading through the manual, keep it in a safe place for future reference. 3

4 Concerning the monitor SAFETY PRECAUTIS WARNING Do not subject the monitor to strong shocks or throw it around. Doing so may cause the liquid crystal to leak and/or the monitor to malfunction, rupture, generate heat and cause a fire. Do not use the monitor wherever there is a risk of ignition or explosions. Do not place the monitor inside a microwave oven or other heating or cooking appliance or pressure vessel. Doing so may cause heat or smoke to be generated in the monitor, combustion and/or damage to the circuit components. Inside the monitor are some high-voltage parts: since exposure to these parts may result in electric shocks or burns, refrain from disassembling, repairing or remodeling the monitor. If a thunderstorm should occur while the monitor is being used outdoors, immediately turn off its power, disconnect the power cable and battery from the main unit, and move the monitor to a safe place. Concerning the power cord Always take hold of the molded part of the plug when disconnecting the power cord. Do not apply force to bend the power cord or bunch it up for use. This may cause a fire. Do not place heavy objects on top of the power cord. This may damage the cord, causing a fire or electrical shock. Concerning foreign matter Do not spill liquids inside the monitor or drop inflammable objects or metal parts into it. Operating the monitor under these conditions may cause a fire, electric shocks and/or malfunctioning. 4

5 CAUTI Concerning the power supply Use a supply voltage within the range of 0V-8V DC for the monitor. Do not turn the power back on immediately after having turned it off. malfunctioning. Doing so can cause Concerning the liquid crystal Due to the nature of liquid crystal, some picture elements may be missing (bright spots, dark spots, etc.) at times. Do not touch any liquid crystal which has leaked from the liquid crystal panel. If the liquid crystal panel has been damaged by mistake and the liquid (liquid crystal) inside has leaked out, keep the liquid away from your mouth and skin and do not inhale its odors. In the event that liquid crystal has made contact with your eyes or mouth, use water to rinse it off immediately. If it has come into contact with your skin or clothing, wipe it off immediately with alcohol, and then rinse it off with soap. Leaving it in place may damage your skin or clothing. Exercise care with the glass of a broken liquid crystal panel. If the panel has broken, be careful not to cut your hands on the glass shards. If you should touch an area where the glass has broken off, you may injure yourself. The LCD panel is a high-precision component and, as such, the following care must be taken in its handling. ) Wiping the panel's surface with benzine, paint thinners, etc. will cause a deterioration in its quality. ) If water (salty water) is left on the display surface, discoloration and staining will result. 3) Exposing the panel directly to ultraviolet rays for an extended period causes the deflection panel to turn brown, in turn causing the contrast to drop and other forms of deterioration to develop in the display quality. 4) Moisture inside the monitor due to condensation, etc. may cause unevenness in the colors. 5) Directly tapping the surface or bumping it into objects may crack the panel, etc. 6) Do not attempt to disassemble the panel since leaking liquid crystal may make contact with your skin, which is hazardous. Handle the liquid crystal protective panel carefully. Gently wipe off any fingerprints or dirt on the liquid crystal protective panel with a cleaning agent used to clean office automation equipment. Rubbing the panel with too much force may mark or damage the panel. Concerning impact This is a precision instrument and, as such, subjecting it to impact may cause malfunctioning. Take special care when moving the monitor. Do not drop the monitor. 5

6 Concerning installation and operation locations Installing the monitor in the following kinds of locations may cause malfunctioning and/or accidents. ) Locations with an ambient temperature outside the range of 0-40 degrees Celsius (see Note ) ) Locations with an ambient humidity outside the range of 30-80% RH 3) Locations in the vicinity of an air conditioner or subject to rapid temperature changes or the formation of condensation 4) Locations exposed to direct sunlight (see Note ) 5) Locations exposed to corrosive gases or high concentrations of dust 6) Locations where strong magnetic fields are generated 7) Locations where the monitor may be splashed with water, oil, chemicals, etc. 8) Locations to which vibrations are transmitted from the floor 9) Unstable locations Take good care to meet the following conditions in order to ensure that the monitor will be used properly. ) Do not place heavy objects such as another monitor directly on top of the monitor. ) Avoid placing any objects around the monitor. Note : When the surface temperature of the LCD panel exceeds 60 degrees Celsius, the panel's backlight and other parts may be damaged. Note : Exposing the panel directly to ultraviolet rays for an extended period causes the deflection panel to turn brown, in turn causing the contrast to drop and other forms of deterioration to develop in the display quality. When the monitor fails to operate properly When the image is not displayed properly, check the format settings. If NoSignal appears on the screen even though input signals have been supplied, check the input settings and the format settings. If the front panel switches should fail to operate, check whether the LOCK switch is at the position. When trouble or malfunctioning occurs In the unlikely event that trouble or malfunctioning should occur, contact your dealer or an Astrodesign sales representative. If trouble should occur in the LCD panel, the user will be charged for repairs and parts replacement even within the warranty period. Concerning this manual It is strictly forbidden to copy this manual either in part or in its entirety without permission from Astrodesign. ) The contents and specifications of this manual are subject to change without notice for the purposes of improving quality. ) Although this manual has been prepared with painstaking care, the user is asked to contact Astrodesign if any ambiguities, mistakes, omissions or other shortcomings are noticed. 6

7 CHAPTER CCERNING THE WM-3004 The WM-3004 is a compact, lightweight and portable LCD waveform monitor which comes in handy for monitoring the pictures being shot during live broadcasts, on location or in studios, etc. The camera battery is supported as the power supply so that pictures, waveforms and sound can be checked even in locations where difficulties have been encountered in the past in carrying in equipment. A full range of functions is provided including functions for adjusting the brightness, contrast and chroma levels as well as functions for displaying markers. Input signals in a total of 3 HDTV video formats are supported.. Outline of WM inch a-si TFT LCD panel featured HD-SDI or YPbPr HD analog input signals (Y-on-sync) supported 3 different video formats supported Standards supporting HD-SDI: SMPTE 9M, BTA-S004B standards complied with (.485 Gbps SDI input) Standards for analog input and supported formats: SMPTE 74M, SMPTE 96M, BTA-S00B standards complied with SDI IN ( ), SDI MITOR OUT, HD analog input (ANALOG Y, ANALOG Pb, ANALOG Pr) and REF IN connectors provided Brightness, contrast, chroma, filter, monochrome, Y gamma adjustment functions Marker display functions (frame, center, 4:3, 3:9, 4:9,.35:,.85:,.66:) Single-action operation of input channels, partial display/non-display of information, picture overlay and freeze/update selection using the switches on the front panel Lighting of red, green LEDs at top of screen by external contact supply-type tally inputs Automatic scanning of input signals possible Automatic /.000 and /.00 frame rate scanning and input signal detection functions CRC error detection function (during HD-SDI input) for input channels Functions for locking the panel switches and storing the setting values Light weight and compact size DC supply power input (0-8V) Camera battery supported 7

8 CHAPTER PARTS AND THEIR FUNCTIS. WM-3004 front panel view and parts WM-3004 front panel view <7> <8> <9> <0 ) <> <6> <> <7> ) <3> <8> <4> <9> <5> <0> F F F3 F4 F5 INPUT DISPLAY OVERLAY FREEZE FUNC PICTURE 3 MENU STATUS AUDIO VECTOR WAVE LOCK <3> <4> <5> <> WM-3004 HD LCD WAVEFORM MITOR POWER <> <6> <0> 8

9 Front panel parts and their functions Number Part Description of function <> Power switch/led <> LOCK switch/led <3> Mode switch This switch is used to turn the power and. (Its LED lights up green while the power is supplied.) This switch is used to lock the panel switches and save the setting values simultaneously. Wait appears at the bottom right of the screen while the settings are being saved, and upon completion of the saving process, PANEL LOCK appears. Do not turn off the power while the setting saving process is in progress. The saved settings are loaded when the power is turned on. (The LED of this switch lights up yellow while the panel switches are locked.) This switch is used to select the monitor's mode. The mode is selected in the following sequence: PICTURE PICTURE PICTURE3 WAVEFORM MENU AUDIO STATUS VECTOR <4> Adjustment dial This dial is used to adjust and select the settings. <5> Setting switch This switch is used to adjust and select the settings. <6> Headphone jack The sound is output from this jack (diameter: 35 mm). <7> Liquid crystal display The images appear on this display. <8> TALLY Tally lamp (red): this is controlled by the rear panel tally connector (contact supply type). <9> TALLY Tally lamp (green): this is controlled by the rear panel tally <0> /4-0UNC threaded hole <> INPUT switch <> DISPLAY switch <3> OVERLAY switch <4> FREEZE switch <5> FUNC switch <6> F switch <7> F switch <8> F3 switch <9> F4 switch <0> F5 switch connector (contact supply type). Threaded hole for a screw to anchor the monitor (used to anchor the monitor to a tripod, arm, etc.). This switch is used to select SDI A or SDI B for the input signals. When it is held down (for more than one second), analog signals are input. This switch is used to set whether the information is to be partially displayed on the screen or not displayed at all. When it is held down (for more than one second), the top and bottom of the screen are inverted. This switch is used to change the picture overlay settings. When it is held down (for more than one second), the color setting screen appears. (The color setting items differ according to the mode selected.) This switch is used to select freeze or update. Freeze is released by switching the input signals or format. Bear in mind that if the input signals are cut off or their format has been changed in the freeze status, the correct data will not be output. This switch is used to select the function switches (switches F to F5). The function of this switch is different depending on each menu which is selected. The function of this switch is different depending on each menu which is selected. The function of this switch is different depending on each menu which is selected. The function of this switch is different depending on each menu which is selected. The function of this switch is different depending on each menu which is selected. 9

10 . WM-3004 rear panel view and parts WM-3004 rear panel view <> <4> <5> <6> <3> <7> <9> <> <0> <8> Names of rear panel parts Number Part Description of function <> Power socket (*) Cannon connector, DC power input socket (GND: pin ; DC IN: pin 4). <> SDI IN Ach HD-SDI signal input connector. <3> SDI IN Bch HD-SDI signal input connector. <4> Y IN HD analog Y signal input connector; synchronization is provided by the Y signal in the case of analog inputs. <5> Pb IN HD analog Pb (Cb) signal input connector. <6> Pr IN HD analog Pr (Cr) signal input connector. <7> MITOR OUT Output connector for simplified monitoring of SDI input signals.sdi A SDI A images are output when the SDI A input is selected. SDI B images are output when the SDI B input is selected. SDI A images are output when the analog input is selected. <8> REF IN Reference input signal connector (HD tri-level sync only). <9> TALLY connector (*) D-sub 9-pin (female) <0> Termination selector switch (*3) This is used to enable or disable the 75Ω termination for the analog signals. 0

11 *: Power socket (no. <>) 4 Pin No. Function GND NC 3 NC 4 DC IN (0-8V) 3 *: TALLY connector (no. <9>) Pin No. Function GND TALLY (green) 3 NC (reserved) (Note) 4 NC (reserved) (Note) 5 NC (reserved) (Note) 6 GND 7 TALLY (red) 8 NC (reserved) (Note) 9 GND When GND and pin are shorted, the green tally lamp lights; when GND and pin 7 are shorted, the red tally lamp lights. (Note) Do not connect anything to the pins marked NC (reserved). Doing so may cause malfunctioning. *3: Termination selector switch (no. <0>) Switch Setting PB Left Right Y Y 75Ω termination No Y termination 75Ω PR HIGH PB PB 75Ω termination No PB termination PR PR 75Ω termination No PR termination As shown in the figure above, the initial setting positions starting with the top one first are left (Y 75Ω termination), left (Pb 75Ω termination) and left (Pr 75Ω termination).

12 3. Connections CHAPTER 3 OPERATI This section describes how to connect the WM () Connecting the power supply Connect the Cannon connector of the AC/DC adapter to the WM-3004's power socket. Check the shape of the connector and socket before use. () Connecting the input signals When SDI signals are to be input: When SDI signals are to be input, use BNC coaxial cables to make the connections to the SDI IN connectors. The SDI IN connectors are where the SDI signals are input; MITOR OUT is an output connector which is used for the simplified monitoring of the SDI input signals. Supply serial input signals complying with the BTA S-004B standard as the HD-SDI input signals. Use a coaxial cable (5C-FB or its equivalent) which can handle the.5 GHz band. When analog signals are to be input: When HD analog signals are to be input, input the YPbPr signals to the respective analog connectors. Input YPbPr signals complying with the BTA S-00B standard as the HD analog input signals. Synchronization is obtained from the Y signal. 3. Usage Precaution to be observed in the WAVEFORM or VECTOR mode: When the waveforms or vectors of analog signals are to be displayed, noise with a maximum level of ±30mV may occur inside the WM Therefore, do not use the monitor for measurements requiring a higher precision. Precaution to be observed in the STATUS mode: Since the WM-3004 employs an 8-bit A/D converter, 00 is always output for the lower bits of the 0 bits displayed in the STATUS mode. A protective film is attached to the surface of the LCD panel. Peel it off before using the WM After checking the connections, turn on the power of the WM-3004 using the POWER switch on the front panel. The POWER LED lights, and images are displayed. If the POWER LED fails to light, check the connections again. To conduct the simplified monitoring of the SDI input signals, use the MITOR OUT connector. The analog input signals will not appear on the monitor if no sync signals are contained in the Y signal. Check the ARIB BTA S-00 and other standards for the levels, etc. If no input signals are supplied, the image area appears all black, and NoSignal is displayed on the screen.

13 3.3 Operation and how to use the switches This section describes the displays which appear on the WM-3004 screen and the setting methods involved. <<Screen displays>> Input SDI A Format AUTO (080i 60.00) Int INPUT 960 F DISPLAY F OVERLAY PICTURE MENU F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC VITC:--:--:--:-- NoSignal YCRCE: PCRCE: (LAST:00:00:00 TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER Note: The area enclosed by the dotted lines in the figure is the image area. Normally, its size is pixels. [Description of modes] The modes are described in the sections listed below. PICTURE mode (refer to section 3.3.) PICTURE mode (refer to section 3.3.) PICTURE3 mode (refer to section 3.3.3) WAVEFORM mode (refer to section 3.3.4) VECTOR mode (refer to section 3.3.5) STATUS mode (refer to section 3.3.6) AUDIO mode (refer to section 3.3.7) mode (refer to section 3.3.3) HELP mode (refer to section 3.3.9) MENU mode (refer to section 3.3.8) This mode is indicated as "" in terms of the position set by the mode switch on the main unit. 3

14 [Description of screen displays] VITC Input Item Description Display modes Format (Reference) NoSignal YCRCE PCRCE Displayed here is the input channel (SDI A, SDI B or Analog) which has been selected by the INPUT switch. The selected format is displayed here. Indicated within the parentheses on the line below are the input signal format and field (or frame) frequency. When analog input has been selected even if 035 input signals are supplied, these signals will be identified as 080 signals. If no signals are input (when NoSignal appears on the screen), "*" appears. (For details on the formats, refer to Chapter 4.) If the format which has been set and the format of the actual input signals differ, Format appears in red. The input reference signal is displayed here. Int denotes an internal sync signal; Ref denotes an external sync signal. If the signal which has been set and the actual input signals differ, NoSignal appears in red. The time code (VITC) is displayed here. This is where the Y signal is checked for CRC errors and the number of errors is displayed. The CRC errors are counted even in the freeze status. When an error is found, YCRCE appears in red for one second. Note: The CRC errors are not counted when analog signals are input. Neither are they counted for one second after the input signals have been changed by the INPUT switch. This is where the Pb and Pr signals are checked for CRC errors and the number of errors is displayed. The CRC errors are counted even in the freeze status. When an error is found, PCRCE appears in red for one second. Note: The CRC errors are not counted when analog signals are input. Neither are they counted for one second after the input signals have been changed by the INPUT switch. The time elapsed since the last error was found is displayed here. P P W V S A M P P W V S A M P P W V S A M P P P3 W V S A M P P P3 W V S A M P P W V S A M P P W V S A M LAST P P W V S A M TIME The time elapsing after the WM-3004 was started or P P W V S error count was reset is displayed here. A M Freeze This indicates the freeze status. When the freeze P P P3 W V status is established, Freeze appears in blue. S A M Filter This indicates whether the video filter is or. P P Mono This indicates whether monochrome is or. P P FRC This indicates whether the 8-bit processing using the P P frame rate control is or. Abbreviations used in display mode column: P PICTURE, P PICTURE, P3 PICTURE3, W WAVEFORM, V VECTOR, S STATUS, A AUDIO, M MENU 4

15 Item Description Display modes G This indicates whether the input video green (G) signal P P is to be displayed. B This indicates whether the input video blue (B) signal is P P to be displayed. R This indicates whether the input video red (R) signal is P P to be displayed. (Marker) This indicates a list of the usable markers. The P P currently selected marker is highlighted. Y-Gamma This indicates the Y gamma setting. P P Bright This indicates the brightness setting. P P Contrast This indicates the contrast setting. P P Pb(Cb) This indicates the Pb (Cb) setting. P P Pr(Cr) This indicates the Pr (Cr) setting. P P YPbPr / GBR This indicates the waveform display method. W Parade / Overlay This indicates the parade display or overlay display for W the waveforms. H / H / F / F This indicates the sweep H/H/F/F switching. W M x / x / x4 This indicates the MAG magnification rate. W G x*.** This indicates the GAIN magnification rate. W dt This indicates the H cursor difference. It does not W appear unless the H cursor is displayed. d% / dv This indicates the V cursor difference. It does not W appear unless the V cursor is displayed. Field / Field This indicates the currently displayed field. It does not W V S appear unless LineSelect is set to. This indicates the line number in the currently displayed W V S Line (Field) field. It does not appear unless LineSelect is set to. Line (Frame) This indicates the line number. It does not appear W V S unless LineSelect is set to. Sample This indicates the sample number. S x.00 This indicates the GAIN magnification rate. V This indicates the position of the displayed waveform. W Volume This indicates the volume level. A L:xCH R:xCH This indicates the embedded audio channels through A which the sound is output. Information This indicates the color of the characters. P P P3 W V S A M Marker This indicates the color of the markers. P P P3 Scale This indicates the color of the scale. W V S A Waveform This indicates the color and brightness of the W waveforms. Cursor This indicates the color of the cursors. W V S Vector This indicates the color and brightness of the vectors. V Status This indicates the color of the status. S A Abbreviations used in display mode column: P PICTURE, P PICTURE, P3 PICTURE3, W WAVEFORM, V VECTOR, S STATUS, A AUDIO, M MENU 5

16 [Description of operations] Switch INPUT switch DISPLAY switch OVERLAY switch FREEZE switch FUNC switch LOCK switch Description of function This switch is used to select the SDI A or SDI B input signals. When it is held down (for more than one second), analog signals are input. If the freeze status is established at this time, it is released. This switch is used to set whether the information is to be partially displayed on the screen or not displayed at all. When it is held down (for more than one second), the top and bottom of the screen are inverted. This switch is used to perform the picture overlay settings. In the PICTURE, PICTURE or PICTURE3 mode, it has no effect since a picture is always displayed. When it is held down (for more than second), the color setting screen appears. (The color setting items differ according to the mode selected.) This switch is used to select freeze or update. Freeze is released by switching the input signals or format. Bear in mind that if the input signals are cut off or their format has been changed in the freeze status, the correct data will not be output. CRC errors are counted even while the freeze status is established. This switch is used to select the function switches (switches F to F5). All key operations are canceled, and the values for the setting items in section 4.6 are saved. Wait appears at the bottom right of the screen while the settings are being saved, and upon completion of the saving process, PANEL LOCK appears. Do not turn off the power while the setting saving process is in progress. The saved settings are loaded and established when the power is turned on. 6

17 3.3. PICTURE mode Picture adjustments screen <<Functions>> The input images can be displayed, and the following video adjustments can be undertaken. Brightness Contrast Chroma Pb (Cb) Pr (Cr) <<Screen>> 7

18 Input SDI A Format AUTO (080i 60.00) Int Filter Mono FRC G B R FRAME CENTER 4:3 3:9 4:9.35:.85:.66: Y-Gamma.000 Bright 0.00% Contrast 00.0% Pb(Cb) 00.0% Pr(Cr) 00.0% INPUT F Bright DISPLAY Contrast F OVERLA Y PICTURE MENU 3 Chroma F3 FREEZE STATUS AUDIO VECTOR WAVE Pb(Cb) Pr(Cr) VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 F4 FUNC WM-3004 HD LCD WAVEFORM MITOR LOCK POWER 8

19 [Description of operations] FUNC switch F switch Bright F switch Contrast F3 switch Chroma F4 switch Pb(Cb) F5 switch Pr(Cr) Switch Description of function This switches the display to the picture adjustment screen. (Refer to section 3.3..) Press this to adjust the brightness using the adjustment dial. Refer to section 4.5. (Variable range: % to %) Press this to adjust the contrast using the adjustment dial. (Variable range: 0.0%-00.0%) When the setting switch is pressed, the contrast is restored to the initial value. Press this to adjust the chroma value using the adjustment dial. (Variable range: 0.0%-00.0%) When the setting switch is pressed, the chroma is restored to the initial value. Press this to adjust the Pb (Cb) value using the adjustment dial. (Variable range: 0.0%-00.0%) When the setting switch is pressed, Pb (Cb) is restored to the initial value. Press this to adjust the Pr (Cr) value using the adjustment dial. (Variable range: 0.0%-00.0%) When the setting switch is pressed, Pr (Cr) is restored to the initial value. 9

20 3.3.. Picture adjustments screen <<Functions>> The input images can be displayed, and the following video adjustment can be undertaken. Y gamma <<Screen>> Input SDI A Format AUTO (080i 60.00) Int Filter Mono FRC G B R FRAME CENTER 4:3 3:9 4:9.35:.85:.66: Y-Gamma.000 Bright 0.00% Contrast 00.0% Pb(Cb) 00.0% Pr(Cr) 00.0% Gamma/Effect F F F3 INPUT DISPLAY OVERLAY PICTURE MENU 3 STATUS AUDIO VECTOR FREEZE WAVE F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] FUNC switch Switch F switch Gamma/Effect F switch F3 switch F4 switch F5 switch Description of function This switches the display to the picture adjustment screen. (Refer to section 3.3..) Press this to adjust the Y gamma value using the adjustment dial. Refer to section 4.5. (Variable range: ; when.000 is exceeded, "Effect" is set.) When the setting switch is pressed, the Y gamma is restored to the initial value. 0

21 Color setting screen <<Functions>> When the OVERLAY switch is held down in the PICTURE mode, the input images can be displayed, and the following settings can be performed. Character color Marker color << screen>> Input SDI A Format AUTO (080i 60.00) Int Information White3 Marker White3 INPUT F Information DISPLAY Marker F OVERLAY PICTURE MENU 3 F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 Exit F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Information F switch Marker F3 switch F4 switch F5 switch Exit OVERLAY switch Description of function Press this to return the display to the previous screen. Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the markers using the adjustment dial. When the setting switch is pressed, the marker color is restored to the initial value. Press this to return the display to the previous screen. When this is held down, the display is returned to the previous screen.

22

23 3.3. PICTURE mode Picture settings screen <<Functions>> The input images can be displayed, and the following settings can be performed. Filter Monochrome FRC Markers <<Screen>> Input SDI A Format AUTO (080i 60.00) Int Filter Mono FRC G B R FRAME CENTER 4:3 3:9 4:9.35:.85:.66: Y-Gamma.000 Bright 0.00% Contrast 00.0% Pb(Cb) 00.0% Pr(Cr) 00.0% INPUT Filter F DISPLAY Mono F OVERLAY PICTURE MENU 3 FRC F3 STATUS AUDIO VECTOR FREEZE WAVE F4 FUNC Marker VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] FUNC switch F switch Filter F switch Mono F3 switch FRC F4 switch F5 switch Marker Switch Description of function This switches the display to the picture settings screen. (Refer to section 3.3..) Press this to set the filter to or. Press this to set monochrome to or. Press this to set the 8-bit processing using frame rate control to or. Press this to set the markers to or. At the marker setting, select the markers using the adjustment dial and enter the selection using the setting switch 3

24 3.3.. Picture settings screen <<Functions>> The input images can be displayed, and the following settings can be performed. Selection of display or non-display for green, blue and red signals of the displayed pictures. (This affects only the picture display.) <<Screen>> Input SDI A Format AUTO (080i 60.00) Int Filter Mono FRC G B R FRAME CENTER 4:3 3:9 4:9.35:.85:.66: Y-Gamma.000 Bright 0.00% Contrast 00.0% Pb(Cb) 00.0% Pr(Cr) 00.0% INPUT Green F DISPLAY Blue F OVERLAY PICTURE MENU 3 Red F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Green F switch Blue F3 switch Red F4 switch F5 switch Description of function This switches the display to the picture settings screen. (Refer to section 3.3..) Press this to select whether to display the green signals of the input pictures. Press this to select whether to display the blue signals of the input pictures. Press this to select whether to display the red signals of the input pictures. 4

25 <<screen>> Color setting screen <<Functions>> When the OVERLAY switch is held down in the PICTURE mode, the input pictures can be displayed, and the following settings can be performed. Character color Marker color Input SDI A Format AUTO (080i 60.00) Int Information White3 Marker White3 INPUT F Information DISPLAY F Marker OVERLAY PICTURE MENU 3 F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/IME:00:00:00 Exit F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Information F switch Marker F3 switch F4 switch F5 switch Exit OVERLAY switch Description of function Press this to return the display to the previous screen. Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the markers using the adjustment dial. When the setting switch is pressed, the marker color is restored to the initial value. Press this to return the display to the previous screen. When this is held down, the display is returned to the previous screen. 5

26 3.3.3 PICTURE3 mode Regular screen <<Functions>> The input pictures are displayed, and all displays with the exception of NoSignal, the time code (VITC), Freeze and the markers are cleared. Apart from displaying the time code (VITC), the functions in the PICTURE3 mode are identical to the PICTURE mode functions. <<Screen>> INPUT F DISPLAY F PICTURE MENU 3 OVERLAY F3 STATUS AUDIO VECTOR WAVE FREEZE F4 F5 FUNC LOCK VITC:--:--:--:-- NoSignal Freeze WM-3004 HD LCD WAVEFORM MITOR POWER [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch F switch F3 switch F4 switch F5 switch Description of function 6

27 <<screen>> Color setting screen <<Functions>> When the OVERLAY switch is held down in the PICTURE3 mode, the input pictures can be displayed, and the following settings can be performed. Character color Marker color Information White3 Marker White3 INPUT Information F DISPLAY Marker F OVERLAY PICTURE MENU 3 F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 Exit F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] FUNC switch Switch F switch Information F switch Marker F3 switch F4 switch F5 switch Exit OVERLAY switch Description of function Press this to return the display to the normal screen. (Refer to section ) Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the markers using the adjustment dial. When the setting switch is pressed, the marker color is restored to the initial value. Press this to return the display to the normal screen. (Refer to section ) When this is held down, the display is returned to the normal screen. (Refer to section ) 7

28 3.3.4 WAVEFORM mode <<Screen>> Function screen <<Functions>> The waveforms are displayed on this screen. Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 INPUT DISPLAY F DISPLAY SWEEP F OVERLAY PICTURE MENU 3 GAIN/MAG F3 FREEZE STATUS AUDIO VECTOR WAVE F4 CURSOR FUNC SETTING VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch DISPLAY F switch SWEEP F3 switch GAIN/MAG F4 switch CURSOR F5 switch SETTING Description of function Press this to return the display to the previous screen. Press this to set the display to the DISPLAY setting screen. (Refer to section ) Press this to set the display to the SWEEP setting screen. (Refer to section ) Press this to set the display to the GAIN/MA setting screen. (Refer to section ) Press this to set the display to the CURSOR setting screen. (Refer to section ) Press this to set the display to the WAVEFORM mode setting screen. (Refer to section ) 8

29 <<Screen>> DISPLAY setting screen <<Functions>> The waveforms can be displayed, and the following settings can be performed. Switching between parade display (side-by-side display) and overlay display (superimposed display) for the waveforms Line select function (with H, H) Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 INPUT Parade Overlay F DISPLAY F Y OVERLAY PICTURE MENU 3 Pb(Cb) F3 FREEZE STATUS AUDIO VECTOR WAVE F4 Pr(Cr) FUNC LineSelect VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] FUNC switch Switch F switch Parade/Overlay F switch Y F3 switch Pb(Cb) F4 switch Pr(Cr) F5 switch LineSelect Description of function Press this to return the display to the function screen. (Refer to section ) Press this to switch between parade display (side-by-side display) and overlay display (superimposed display) for the waveforms. Press this to set Y/G to or. Press this to set Pb/B to or. Press this to set Pr/R to or. Press this to set line select to or. When line select is, the lines are incremented or decremented using the adjustment dial, and the field is switched using the setting switch. (This applies with H or H only; field switching applies only with interlacing or segmented frame format.) 9

30 <<Screen>> SWEEP setting screen <<Functions>> The waveforms can be displayed, and the following settings can be performed. H, H, F or F display switching Line select function (with H or H) Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 H F INPUT H DISPLAY F PICTURE F F3 OVERLAY MENU 3 STATUS AUDIO VECTOR F F4 FREEZE WAVE LineSelect F5 FUNC LOCK VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00 TIME:00:00:00 WM-3004 HD LCD WAVEFORM MITOR POWER 30

31 [Description of operations] FUNC switch F switch H F switch H F3 switch F F4 switch F F5 switch LineSelect Switch Description of function Press this to return the display to the function screen. (Refer to section ) H H (with interlacing or segmented frame format) In the line select status, the odd-numbered fields are displayed on the left side, and the even-numbered fields are displayed on the right side. In the line select status, the selected line is displayed on the left side, and the next line in the selected field is displayed on the right side. F The horizontal blanking data is not displayed. F (with interlacing or segmented frame format) The odd-numbered fields are displayed on the left side, and the even-numbered fields are displayed on the right side. The horizontal blanking data is not displayed. Press this to set line selection to or. In the line select status, the lines are incremented or decremented using the adjustment dial, and the field is switched using the setting switch. (This applies with H or H only; field switching applies only with interlacing or segmented frame format.) 3

32 GAIN/MAG setting screen <<Functions>> The waveforms can be displayed, and the following settings can be performed. Gain (0.03X to 7.97X), MAG (X, X or 4X) setting Scroll functions <<Screen>> Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 INPUT GAIN.00 F DISPLAY MAG 4 Adj.Dial Gain Val Scroll F F3 F4 OVERLAY FREEZE PICTURE MENU 3 STATUS AUDIO VECTOR WAVE SCROLL Up Down Left Right F5 FUNC LOCK VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 WM-3004 HD LCD WAVEFORM MITOR POWER 3

33 [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch GAIN x*.** F switch MAG x/x/x4 F3 switch RENC GainVal/Scroll F4 switch UP DOWN/LEFT RIGHT F5 switch Description of function Press this to return the display to the function screen. (Refer to section ) When setting the gain Use the dial to set the magnification GainVal rate of the gain. (Variable range: 0.03 to 7.97) When scrolling Scroll Use the dial to scroll vertically or When setting the gain GainVal horizontally. The gain is an integral value after the decimal places have been rounded down (with a figure or 4 or below) or rounded up (with a figure of 5 or above). (All values below.00 are set to.00; similarly, all values above 7.00 are set to 7.00.) If the gain magnification rate is an integer, it is increased in.00 increments, and when 7.00 is reached, it is returned to.00.) When scrolling Scroll Use the switch to reset the scrolling. Press this to switch the adjustment dial and setting switch functions to gain. Press this to select the MAG magnification rate (X, X or 4X). Press this to switch the adjustment dial function between the gain setting and scrolling. Press this to select vertical (up/down) or horizontal (left/right) scrolling. 33

34 CURSOR setting screen <<Functions>> The waveforms can be displayed, and the following setting can be performed. H and V cursor display and difference display (mv, µs) <<Screen>> Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 INPUT H F DISPLAY V F OVERLAY PICTURE MENU 3 MOVE BASE SET TRACK F3 FREEZE STATUS AUDIO VECTOR WAVE H/V H V F4 F5 FUNC LOCK VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 WM-3004 HD LCD WAVEFORM MITOR POWER [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch H F switch V F3 switch MOVE BASE/SET/TRACK F4 switch H/V F5 switch Description of function Press this to return the display to the function screen. (Refer to section ) Use this to move the cursor horizontally or vertically. Press this to set the H cursor to or. Press this to set the V cursor to or. Press this to select the cursor (BASE, SET or TRACK) to be moved. Press this to select the cursor (H or V) to be moved. 34

35 WAVEFORM setting screen <<Functions>> The waveforms can be displayed, and the following settings can be performed. Waveform display YPbPr/GBR switching V ancillary (Wave), H blanking switching Scale switching LPF (Wave) switching <<Screen>> Input SDI A Format AUTO (080i 60.00) Int YPbPr Parade H Mx G x.00 dt 8.00µs d% 0.00% Field Line(Field) 000 Line(Frame) 000 Waveform YPbPr GBR F INPUT DISPLAY V anc(wave) F OVERLAY PICTURE MENU 3 H Blank F3 FREEZE STATUS AUDIO VECTOR WAVE Scale % V LPF(Wave) VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 F4 FUNC WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch Waveform YPbPr/GBR F switch V anc / F3 switch H Blank / F4 switch Scale %/V F5 switch LPF(Wave) / Description of function Press this to return the display to the function screen. (Refer to section ) Press this to switch between YPbPr and GBR for the waveform display. Press this to set V ancillary to or. This takes effect only when the WAVEFORM mode is established. Press this to set H blanking to or. Press this to switch the scale units between % and V. Press this to set the low-pass filter (Wave) to or. This takes effect only when the WAVEFORM mode is established. 35

36 Color setting screen <<Functions>> When the OVERLAY switch is held down in the WAVEFORM mode, the following settings can be performed. Character color Scale color Waveform color and brightness Cursor color <<Screen>> Input SDI A Format AUTO (080i 60.00) Int Information White3 Scale White Waveform Color5 Cursor Yellow INPUT F Information DISPLAY F Scale Exit Waveform F3 OVERLAY FREEZE PICTURE MENU 3 STATUS AUDIO VECTOR WAVE Cursor F4 FUNC VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Information F switch Scale F3 switch Waveform F4 switch Cursor F5 switch Exit OVERLAY switch Description of function Press this to return the display to the previous screen. Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the scale using the adjustment dial. When the setting switch is pressed, the scale color is restored to the initial value. Press this to select the color (any of 6 colors) and brightness of the waveforms using the adjustment dial.when the setting switch is pressed, the waveform color is restored to the initial value. Press this to select the color (any of 64 colors) of the cursor using the adjustment dial. When the setting switch is pressed, the cursor color is restored to the initial value. Press this to return the display to the previous screen. When this is held down, the display is returned to the previous screen. 36

37 3.3.5 VECTOR mode <<Screen>> Normal screen <<Functions>> The signals on the vectorscope can be displayed, and the following settings can be performed. Increase of black, white levels Line selection function Input SDI A Format AUTO (080i 60.00) Int.00 Field Line(Field) 000 Line(Frame) 000 INPUT GAIN Fix x Val x.00 F F DISPLAY PICTURE OVERLAY MENU 3 F3 FREEZE STATUS AUDIO VECTOR WAVE F4 FUNC LneSelect VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER 37

38 [Description of operations] FUNC switch Switch Adjustment dial Setting switch F switch GAIN Fix x/val x*.** F switch F3 switch F4 switch F5 switch LineSelect Description of function This switches the display to the VECTOR mode setting screen. (Refer to section ) When the gain setting is fixed Fix x When the gain setting Use the dial to set the magnification can be varied Val x*.** rate of the gain. (Variable range: 0.03 to 7.97) When line select is Use the dial to increment or decrement the lines. When the gain setting is fixed Fix x When the gain setting can be varied Val x*.** When line select is The gain is an integral value after the decimal places have been rounded down (with a figure or 4 or below) or rounded up (with a figure of 5 or above). (All values below.00 are set to.00; similarly, all values above 7.00 are set to 7.00.) If the gain magnification rate is an integer, it is increased in.00 increments, and when 7.00 is reached, it is returned to.00.) Use the switch to select the field. (This applies with H or H only; field switching applies only with interlacing or segmented frame format.) Press this switch to set line select to and switch between the fixed (Fix x) and variable (x*.**) gain setting. In the fixed (Fix x) status, the loci between the pixels are interpolated for the display; in the variable status, only the points are displayed. Press this to set line select to or. When line select is, the gain setting is fixed (Fix x). 38

39 VECTOR mode setting screen <<Functions>> The signals on the vectorscope can be displayed, and the following settings can be performed. V ancillary (Vect) switching Scale switching LPF (Vect) switching <<Screen>> Input SDI A Format AUTO (080i 60.00) Int.00 Field Line(Field) 000 Line(Frame) 000 INPUT F DISPLAY V anc(vect) F OVERLAY PICTURE MENU 3 F3 STATUS AUDIO VECTOR FREEZE WAVE Scale 00% 75% F4 FUNC LPF(Vect) VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] FUNC switch Switch Adjustment dial Setting switch F switch F switch V anc(vect) / F3 switch F4 switch Scale 00%/75% F5 switch LPF(Wave) / Description of function This switches the display to the normal screen. (Refer to section ) Press this to set V ancillary to or. This takes effect only when the VECTOR mode is established. Press this to switch the scale between 00% or 75%. Press this to set the low-pass filter (Vect) to or. This takes effect only when the VECTOR mode is established. 39

40 <<Screen>> Color setting screen <<Functions>> When the OVERLAY switch is held down in the VECTOR mode, the following settings can be performed. Character color Scale color Vector color and brightness Cursor color Input SDI A Format AUTO (080i 60.00) Int Information White3 Scale White Vector Green6 Cursor Yellow INPUT Information F DISPLAY Scale F OVERLAY PICTURE MENU 3 Vector F3 FREEZE STATUS AUDIO VECTOR WAVE Cursor F4 FUNC Exit VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00 TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Information F switch Scale F3 switch Vector F4 switch Cursor F5 switch Exit OVERLAY switch Description of function Press this to return the display to the previous screen. Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the scale using the adjustment dial. When the setting switch is pressed, the scale color is restored to the initial value. Press this to select the color (any of 64 colors) and brightness of the vectors using the adjustment dial. When the setting switch is pressed, the vector color is restored to the initial value. Press this to select the color (any of 64 colors) of the cursor using the adjustment dial. When the setting switch is pressed, the cursor color is restored to the initial value. Press this to return the display to the previous screen. When this is held down, the display is returned to the previous screen. 40

41 3.3.6 STATUS mode <<Screen>> Normal screen <<Functions>> The statuses can be displayed, and the following settings can be performed. Status (numerical value) display EAV, SAV display Input SDI A Format AUTO (080i 60.00) Int Field Line(Field) 000 Line(Frame) 000 Sample 0000 INPUT F EAV DISPLAY F SAV OVERLAY PICTURE MENU 3 Line Sample F3 FREEZE STATUS AUDIO VECTOR WAVE HEX DEC OCT BIN F5 F4 FUNC LOCK VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00/TIME:00:00:00 WM-3004 HD LCD WAVEFORM MITOR POWER [Description of operations] Switch FUNC switch Adjustment dial Setting switch F switch EAV F switch SAV F3 switch Line/Sample F4 switch HEX/DEC/OCT/BIN F5 switch Description of function Use the dial to increment or decrement the lines or samples in the status displayed. Press this to select the field (with interlacing or segmented frame format). Press this to jump to EAV. Press this to jump to SAV. Press this to select the item (Line or Sample) to be set using the adjustment dial. Press this to select HEX (hexadecimal), DEC (decimal), OCT (octal) or BIN (binary) for the cardinal numbers of the displayed data. 4

42 Color setting screen <<Functions>> When the OVERLAY switch is held down in the STATUS mode, the following settings can be performed. Character color Scale color Status color Cursor color <<Screen>> Input SDI A Format AUTO (080i 60.00) Int Information White3 Scale White Status White3 Cursor Yellow INPUT Information F DISPLAY Scale F OVERLAY PICTURE MENU 3 Status F3 FREEZE STATUS AUDIO VECTOR WAVE F4 Cursor FUNC Exit VITC:--:--:--:-- YCRCE: PCRCE: (LAST:00:00:00 TIME:00:00:00 F5 WM-3004 HD LCD WAVEFORM MITOR LOCK POWER [Description of operations] Switch FUNC switch F switch Information F switch Scale F3 switch Status F4 switch Cursor F5 switch Exit OVERLAY switch Description of function Press this to return the display to the previous screen. Press this to select the color (any of 63 colors) of the characters using the adjustment dial. When the setting switch is pressed, the character color is restored to the initial value. Press this to select the color (any of 64 colors) of the scale using the adjustment dial. When the setting switch is pressed, the scale color is restored to the initial value. Press this to select the color (any of 64 colors) of the statuses using the adjustment dial. When the setting switch is pressed, the status color is restored to the initial value. Press this to select the color (any of 64 colors) of the cursor using the adjustment dial. When the setting switch is pressed, the cursor color is restored to the initial value. Press this to return the display to the previous screen. When this is held down, the display is returned to the previous screen. 4