ADVISORY PANEL WITH AREA SELECTION SWITCHING AND CONNECTION MODULE

Transcription

1 PZ-000 DVISORY PNEL WITH RE SELECTI SWITCHING ND CNECTI MODULE DESCRIPTI PZ-000 DESK The PZ-000 digital desk can provide ads per selective areas and general announcements. It works in conjunction with the module. It can handle from to 0 selectors areas with a maximum of 00 zones. It is also possible to use up to PZ-000 desks in the same system. The different elements are interconnected via a FTP bus cable, providing a flexible, reliable and easy to use. General characteristics: -Digital display. -Zone selection buttons. -Management selectors PZ-000 modules. -Easy itegration with the GD- digital player/recorder. -LED driver status. -Notice carillon. -Microphone volume and chime adjustment. -uxiliary input signal. -uxiliary output signal. -Maximum distance from panel to switch: 000 m. -Power supply Vdc. DESCRIPTI PGING SELECTOR WZ-000 MUSIC /CLL LL ZE POWER MIC MIC MIC PGING ZES 0 0 zones switching module with music and advertisements selection. It can function independently, or bus, operated by the desk PZ-000. It allows the areas of music and announcements selection. It integrates mixer with microphone inputs, line and chime notice. The system allows a maximum of 0 modules (up to a maximum of 00 zones). y two power amplifiers, can stream music and announcements selective. General characteristics: -Maximum distance to desk center: 000 m -Memory selection of areas of non volatile music. -Maximum power-line speaker: 00 W. -Status indication by LED drivers zones of two colors: green for music, red for ads. -Oscillator with two microphone inputs dynamic unbalanced -Two-line inputs direct to mixer UNI DESRROLLOS ELECTRICOS UDE reserves the right to modify the technical characteristics of its products without previous notice PULIC Systems arcelona Madrid vda. RCEL, 00 - SNT JON DESPÍ RCEL - ESPÑ Tel: + Fax: + ude@udeaudio.com C/ LUIS I,, ª planta 0 - MDRID ESPÑ Tel: + 0 Fax: + 0 centro@udeaudio.com Rev. 0.0

2 PZ-000 / NNOUNCEMENTS WITH SELECTI RES PZ-000 DESK FRT CTROLS LED utton SELECTED RE LED button GENERL NOTICE CTIVTI LED button 0 ZES CTIVTI CH CH CH CH CH CH CH CH CH 0 LED button CRILL CTIVTI LED button TLK - Microphone / MIC / TEN ZES LL ZES SWITCHES STEERING. Connector XLR - Micro desk lphanumeric display indicator selected RER CNECTIS Power switch / VDC power input terminals DC V IN MIC VDC power input connector US communication port uxiliary output signal uxiliary input signal Microphone volume Chime volume Model: Output: Microphone input (not balanced): Line input (not balanced): andwidth MICRO: andwidth : Crosstalk input MICRO: Croostalk input : Power source: Consumption: Dimensions: Weight: SPECIFICTIS PZ-000 Unbalanced. 0 mv./ mv./ 0K. from 00 Hz. to Khz. from 0 Hz. to Khz. 0 d. 0 d. Power supplied 0VC / VDC. 0 W. xx0 mm., Kgs. Rev. 0.0

3 PZ-000 / FRT CTROLS SWITCHING ND CNECTI MODULE MUSIC / CLL LL ZE POWER MIC MIC MIC PGING ZES 0 Power On. Volume Micro Mic input (Jack) Power light. Selectors with LED SELECTED RES Volume Micro selector Selectors with LED MUSIC / NNOUNCEMENTS Selectors with LED SELECTI GENERL RES RER CNECTIS a a a CH CH CH CH CH CH CH CH CH 0 LRM OUT SS TRELE MIC IN CH CH CH CH CH CH CH CH CH 0 UDIO OUT IN IN 0 b b b Mic input (Jack). Chime volume. Input and Warning signs UDIO output selector DIRECTI a b a b US communication port Input (-) music ZE Input (+) music ZE Input (-) ads ZE Input (+) ads ZE a b 0 Outputs (-) speaker line ZE (*) Outputs (-) signal ZE (*) Output (+) speaker line ZE (*) Output (+) signal ZE (*) 0 VC power input SIGNL input NNOUNCEMENTS Output NNOUNCEMENTS REPORTS (*) Connection mode: output line 00V (*) Connection mode: output signal 0 d SPECIFICTIS Model: WZ-000 Output: Unbalanced. microphone inputs (not balanced):, mv./ 00. line inputs (not balanced): 00 mv./ 0K. andwidth MICRO: from 00 Hz. to Khz. andwidth : from 0 Hz. to Khz. Crosstalk input MICRO: 0 d. Crosstalk input : 0 d. Power source: 0 VC. Consumption: 0 W. Dimensions: x0x mm. Weight:,0 Kgs. Properties (work by modulating Vox): The microphone input has priority over a microphone, line and remote PZ-000 desk. The input Line has priority over a microphone, microphone, line and remote PZ-000 desk. Rev. 0.0

4 PZ-000 / CNECTIS PZ-000 / Figura VDC VDC () () Zones: to 0 Zones: to 0 PZ-000 () PZ-000 () Number ZES a0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 0 a 00 MICROSWITCH POSITI ROWN ROWN-WHITE LUE LUE-WHITE Figure LUE LUE-WHITE ROWN ROWN-WHITE ORNGE ORNGE-WHITE GREEN GREEN-WHITE shield shield ORNGE ORNGE-WHITE GREEN GREEN-WHITE CNECTOR FTP RJ The metallic shield must be connected. CNECTOR FTP RJ STRUCTURE OF TECHNICL PZ-000 / Connect the PZ-000 desks modules and bus cable FTP. ttention to the connection of RJ connectors (see Figure ). Connect Vdc power supply included with each desk. switches march. Microphone volume and chime halfway. Connect the modules with wholes corresponding elements (see TYPICL CNECTI). Configuration module, assigning the identification number of buses by the microswitches on the rear panel, as Figure (address code setting). number : zones to 0 number : zones to 0 number : zones to 0... Rev. 0.0

5 PZ-000 / CFIGURE THE IDENTIFIERS OF ECH PZ-000 DESK Configure the identifiers of each PZ-000 desk (from to ). Each PZ-000 must have a different identifier on the bus. Process: Power switch in Hold the selector NOTICE GENERL (LL RES) is activated during the switch to start position. The display shows " d". Release the button GENERL NOTICE. Operate SWITCHES STEERING (up / down) until the display shows the required ID number (example ). Validate the identifier by pressing GENERL NOTICE. Turn the switch off, and seconds later, put another time in. Whenever you set up the desk, the display shows quickly the identification number (in this case 0.) and then putting the last address previously selected. nd configure each console system with its corresponding identifier.. USE PZ-000 DESK TO GIVE NOTICE Example : We want to give a notice to number.. y SWITCHES STEERING select the number ( no. module) which belong to zone.. y the ZE SELECT button activate the zone. The corresponding LED driver is activated fixed. In zone the music is off (if it was enabled). In all other areas not selected, the music continues. OF NOTICE: Press the corresponding button ( ). The associated LED lights the chime sounds in the selected area.. NOTICE: y the button (MIC / ), turn on the microphone. The pilot lights. Give the notice. t the end, turn off the microphone by pressing button (MIC / ). Defuse the ZE SELECTOR number. The pilot zone LED turns off. Example : Notice to zones to 0 Proceed as in the previous section, but by selecting the 0 CTIVTI RES (TEN RES). The 0 areas are activated simultaneously. Example : Notice to zones, and 0:. y SWITCHES STEERING select the number ( no. module) which belong to zone.. ctivate by the ZE SELECT button the zone. The corresponding LED driver is activated fixed.. y SWITCHES STEERING select the number ( no. module) that belong to areas and 0.. y the ZE SELECT button activate areas and 0. The corresponding LED drivers are activated fixed. In areas, and 0 the music is off (if it was enabled). In all other areas not selected, the music continues. OF NOTICE: Press the corresponding button ( ). The associated LED lights while the chime sounds in the selected area.. NOTICE: y the button (MIC / ), turn the microphone. The pilot lights. Give the notice. t the end, turn the microphone back on el pressing button (MIC / ). Defuse the SELECTOR RE Number, and 0 and in reverse order of selection. GENERL NOTICE: y selecting the GENERL NOTICE (LL RES) all areas of the system are activated at a time. t the end of the notice, deselect the GENERL NOTICE. Note: Selecting and Deselecting NOTICE, erase all current selections possible. Rev. 0.0

6 PZ-000 / USE PZ-000 DESK PRIORITIES: Manual selection in the module areas has priority on the desks PZ-000. When there is more of one desk in the PZ-000 system, must consider the following: PZ-000 consoles have the same priority among themselves. The first that select a zone takes control of the system until is deselected. If a desk PZ-000 tries to select a certain area, while another is a function, the LEDs light up quickly and deactivate. If a desk PZ-000 seeking access to nonexistent package, the LEDs flash slowly and deactivate. USE MODULE. SELECTI OF MUSIC ZES: y the selector MUSIC / EVENTS (MUSIC / CLL) with the corresponding driver in green, select the buttons SELECTORS ZE (ZE PGING), or areas you want the music. Green pilot light: area with music. Green pilot disabled: an area without music. The selector GENERL RES (LL RES) can also select / deselect all areas of music at once.. NNOUNCEMENTS Y THE ENCTMENT OF THE DESK: SELECTING DVERTISEMENTS: Operate the selector MUSIC / NNOUNCEMENTS; the red driver. Or select the areas you want to enact the announcement by the ZE SELECTORS, or with the GENERL selector. The selected areas turn red (If there's selected music in the area, in orange). t the end of the notice, deselect areas review and carry out the inverse of the selection. The promulgation of the GENERL notice in the module affects only the 0 areas of this module. In addition the selection in local mode is possible to control the PZ-000 desk. The selections and actions in the desk take precedence over affected from the desk PZ NNOUNCEMENTS Y THE ENCTMENT OF THE PZ-000 DESK: See use PZ-000 desk.. SPECIL LRM FETURES: The DIP switch number must be in position in order to enable the special alarm features. When the or input is triggered, with a close contact, all the zones would be connected to the alarm amplifier. In the front panel will flash on in red or orange. t the same time alarm OUT / of all connected on the system will close free voltage contact. n instant reset could be done, pushing the all zone button, realizing all zones system (in case more than one is installed). Rev. 0.0

7 PZ-000 / TYPICL CNECTI (L00V Output) 0 VC. 00V SPEKERS ZE CH CH CH L00V INPUT MPLIFIER MUSIC MPLIFIER MUSIC SPEKERS ZE 0 L00V INPUT MPLIFIER NNOUNCEMENTS UX OUT MUSIC SOURCE MPLIFIER NNOUNCEMENTS 0 VC. 0 VC. CH CH CH CH CH CH CH CH CH 0 DC V IN MIC PZ-000 VDC SS TRELE LRM OUT CH CH CH CH CH CH 0 UDIO OUT IN IN 00V UX MIC IN 0 VC. Rev. 0.0

8 PZ-000 / - Modification to operate with 0 d audio signals REMOVE COVER ND CUT THE RESISTNCE S IF SHOWN, CUT THE RESISTNCE R R R R R R R R R R R0 IMPORTNT: used with L00V should not be reused with 0 d signal Rev. 0.0

9 PZ-000 / TYPICL CNECTI (0 d output signal) 0 VC. SPEKERS ZE SPEKERS ZE 0 L00V L00V MPLIFIER POWER ZE SIGNL INPUT MPLIFIER POWER ZE 0 SIGNL INPUT 0 VC. 0 VC. PZ-000 VDC DC V IN MIC CH CH CH CH CH CH CH CH CH 0 SS TRELE LRM OUT MIC IN CH CH CH CH CH CH CH CH CH 0 UDIO OUT IN IN SIGNL PREMPLIFIER MUSIC UX OUT MUSIC SIGNL SOURCE PREMPLIFIER NNOUNCEMENTS UX 0 VC. 0 VC. 0 VC. Option: The preamplifiers can be replaced by a Preamplifier PX- Rev. 0.0