EPSON PowerLite 50c/70c Multimedia Projector. User s Guide

Transcription

1 EPSON PowerLite 50c/70c Multimedia Projector User s Guide

2 Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel. WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation. Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp. Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this EPSON product. EPSON is not responsible for any use of this information as applied to other products. Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with SEIKO EPSON CORPORATION s operating and maintenance instructions. SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products by SEIKO EPSON CORPORATION. EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite and Presenters Club are registered trademarks; EPSON Store and SizeWise are trademarks; and EPSON PrivateLine and Extra Care are service marks of Epson America, Inc. General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks. CPD Copyright 2001 by Epson America, Inc. 01/01 ii

3 Contents Welcome Using Your Documentation Reading This Manual Online Getting More Information Registration and Warranty Setting Up the Projector 2Using the Projector Unpacking the Projector Additional Components Optional Accessories Positioning the Projector Choosing Your Connections Connecting to a Computer Connecting to a PC Laptop Connecting to a PC Desktop Computer Connecting to a PowerBook Connecting to a Macintosh Desktop Computer Connecting to Video Sources Connecting the RCA A/V Video Cable Connecting an S-Video Cable Connecting a Component Video Cable Connecting to External Speakers or a PA System Turning On Your Equipment What To Do If You See a Blank Screen Adjusting Your Image Focusing Your Image Adjusting the Image Size Adjusting the Image Height Adjusting the Image Shape Adjusting the Image Quality Contents iii

4 Using the Remote Control Installing the Remote Control Batteries Operating the Projector with the Remote Control Using the Remote Control as a Wireless Mouse Controlling Audio and Video Switching Between Picture Sources Freezing the Picture Turning Off the Picture and Sound Adjusting Sound Volume Highlighting Your Presentation Using the Cursor/Stamp Arrow Drawing a Horizontal Bar Shutting Down the Projector Fine-Tuning the Projector 4Maintaining and Transporting the Projector 5Solving Problems Using the Menus Changing Menu Settings Adjusting the Image Adjusting the Sound Customizing the Highlighting Tools Customizing Projector Features Viewing Projector Information Restoring the Default Settings Cleaning the Lens Cleaning the Projector Case Cleaning the Air Intake Vent Replacing the Lamp Transporting the Projector Using the On-Screen Help Checking the Projector s Lights Image or Sound Problems Problems with the Remote Control Where To Get Help iv Contents

5 6Technical Specifications General Projection Lamp Remote Control Mouse Compatibility Dimensions Electrical Environmental Safety Computer Connector Pin Assignments Compatible Video Formats Notices Important Safety Instructions Remote Control Information Declaration of Conformity FCC Compliance Statement Index Contents v

6 WWelcome Your EPSON PowerLite 50c or PowerLite 70c is a small, lightweight, affordable projector offering powerful 3-LCD performance and easy-to-use controls. Your projector weighs less than 7 pounds and displays full-color images at a resolution of up to pixels (EPSON PowerLite 50c) or pixels (EPSON PowerLite 70c). Producing up to 700 ANSI lumens (EPSON PowerLite 70c) or 1000 ANSI lumens (EPSON PowerLite 50c), your projector creates bright images that can be easily seen in rooms light enough to take notes. You can connect it simultaneously to two image sources: a computer and a video device, such as a VCR, DVD player, laser disc player, camcorder, or digital camera. You can also connect audio for each image source. You can operate your projector through a hand-held remote control, with buttons for zooming in on your image, adjusting volume, and accessing all the projector s features. You can also use the remote control as a wireless mouse, and run your presentation as you move around the room. EPSON s SizeWise technology supports a range of computer outputs, for a full-size image from just about any notebook PC or PowerBook. If you use a VCR or other video source, the projector automatically senses the video format, so you can use it with confidence no matter where in the world you travel. The EPSON PrivateLine SM Technical Support program will get you help when you need it. A special 800 number and your own PIN will connect you with a projector support specialist fast. Welcome 1

7 warning caution note Using Your Documentation To connect the projector to your laptop and get your presentation running fast, see the Quick Setup sheet that came in your Owner s Kit. This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: Warnings must be followed carefully to avoid bodily injury. Cautions must be observed to avoid damage to your equipment. Notes contain important information about your projector. Reading This Manual Online Your EPSON PowerLite CD-ROM includes an electronic copy of this manual. You may find it convenient to copy it onto your laptop s hard drive so it s always with you for example, when taking your presentation on the road. note If you do not have Acrobat Reader, you can install it from the CD-ROM. To view your electronic manual, you need to use Adobe Acrobat Reader. Just insert the CD-ROM in your drive, select the Install/View User s Guide button and click Install User s Guide or View User s Guide. When you open the manual, you see this toolbar: show navigation pane first page previous page last page next page You have several ways to navigate through the manual: Click in the table of contents on the left side of the screen to move quickly to the topic of your choice. Use the arrow buttons in the toolbar or on the vertical scroll bar on the right side of the screen to move through the manual. 2 Welcome

8 If you hold your mouse pointer over text and the hand changes to an index finger, you can click to jump to a related topic. For more information, see your Acrobat Reader online guide. Getting More Information Need more tips on giving presentations? How about quick steps for setting up your projector? Here s where you can look for help: Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the Presenters Club and it s free. Quick Setup sheet Gives you all the instructions you need to get your projector set up and connected to a laptop or PowerBook computer. Owner s Kit Includes your Quick Setup sheet, warranty brochures, CD-ROMs, and EPSON PrivateLine Support card. Store this User s Guide in the folder and keep the folder with your projector at all times. Built-in help system Provides assistance for common problems. Available from the Help button on the projector or the remote control. See page 51 for details. support.epson.com Download FAQs and your questions to EPSON support. CD-ROMs Your Owner s Kit includes the EPSON PowerLite CD-ROM that lets you register electronically, and includes the electronic copy of this book as well as a link to Presenters Online. note You don t need to install any software to use your projector. Welcome 3

9 If you still need help after checking this User s Guide and the sources listed above, you can use the EPSON PrivateLine Support service to get help fast. Call (800) and enter the PIN on the card in your Owner s Kit. Or take advantage of EPSON s automated support services 24 hours a day. See page 58 for more information. Registration and Warranty Your projector comes with a basic carry-in warranty as well as an international warranty that let you project with confidence anywhere in the world. For details, see the warranty brochures included in your Owner s Kit. In addition, for customers who register their projector, EPSON offers free Extra Care SM Road Service. In the unlikely event of an equipment failure, you won t have to wait for your unit to be repaired. Instead, EPSON will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See the brochure in your Owner s Kit for details. To register, simply insert the EPSON PowerLite CD-ROM that came with your projector and select Register Online. Registering also lets you receive special updates on new accessories, products, and services. You can register through the Internet, by or 800-number modem connection, or by printing out the form to fax or mail. 4 Welcome

10 1Setting Up the Projector This chapter tells you how to unpack your projector and set it up for a presentation. The projector must be connected to a computer or a video source such as a DVD player, VCR, camcorder, digital camera, or other video device before it can project images. To set up the projector, you need to: Unpack and position the projector Connect the projector to one or more input sources Unpacking the Projector Make sure you have all the parts shown: remote control batteries power cord computer cable A/V cable projector with lens cover PS/2 mouse cable USB mouse cable CD-ROM (not needed to use the projector) Soft carrying case note You won t need all these components; your configuration will determine which ones you need. Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use a carrying case (either an EPSON case or something similar, such as a laptop case). See page 50 for transportation instructions. Setting Up the Projector 5

11 Additional Components Depending on how you use the projector, you may need these additional components: To receive an S-Video signal, you need an S-Video cable (usually provided with your video device). Older imac systems may need a special adapter to provide a VGA output port; see your computer dealer. To project HDTV images, you ll need an HDTV cable, available from most electronics dealers. To receive an audio signal, you ll need a stereo mini-jack cable, available from most electronics dealers. Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Customized carrying cases: ATA molded hard shell carrying case ATA shipping case Samsonite wheeled soft case Notebook/Projector soft shoulder bag Replacement lamp Ceiling mount Projection screens: 50-inch portable screen 60-inch Insta Theatre screen 80-inch Insta Theatre screen Component video cable Macintosh adapter set Kensington security lock Presentation audio system Wireless microphone system Product number ELPKS36 ELPKS37 ELPKS35 ELPKS13 ELPLP13 ELPMB35 ELPSC06 ELPSC07 ELPSC08 ELPKC19 ELPAP01 ELPSL01 ELPPAS1 ELPCVS1 6 Setting Up the Projector

12 You can purchase these accessories from your dealer, or by calling EPSON at (800) , or by visiting the EPSON Store at (U.S. sales only). In Canada, please call (800) for dealer referral. Positioning the Projector The location in which you choose to set up your projector depends on the size of the room and your presentation style. Place the projector on a sturdy, level surface, within this distance from the screen: 3.3 to 36 feet in Wide mode 3.9 to 43.2 feet in Tele mode (see page 28 for more information on these modes) Make sure there is plenty of space for ventilation around and under the projector. Make sure the projector is within 6 feet of a grounded electrical outlet or extension cord, and within 5 feet of your computer and/or video source. Place the projector directly in front of the center of the screen, facing it toward the screen squarely. Otherwise, your image will not be square. Most presenters find it convenient to place the screen in the front of the room with the projector back near the front of the audience, leaving ample room between the screen and projector to get a good-sized image. Then the presenter can stand in front of the room, facing the audience and control the equipment from there. note It s best to position the screen directly in front of the room. If it s placed diagonally in a corner, it s much more difficult to aim the projector at the screen correctly and get a square image. Setting Up the Projector 7

13 Use the figure below as a guideline to help you determine how far from the screen to place the projector. Your image size may not exactly match these sizes; its actual size depends on whether you have adjusted the image size setting (using keystone correction or the Wide/Tele button). 40 ft. 8 ft. 4 ft. distance from the screen When projecting from a table, the ideal arrangement is to set the projector flat on its surface with the base of the lens at about the level of the bottom of the screen. This delivers the best-looking picture. If you have to raise the projector by adjusting its feet (described on page 29), you ll need to square-up the sides of image by pressing the Keystone button (see page 30). If you ll be projecting from overhead, you ll get the best-looking picture by mounting the projector upside-down, parallel to the ceiling, with the bottom of the lens level with the top of the screen. (You ll also need to select ceiling projection mode in the projector s Advanced menu; see page 42.) 8 Setting Up the Projector

14 Choosing Your Connections The connections you ll need to make depend on the equipment you re using, whether your presentation includes sound, and whether you plan to use the remote to run your presentation. Connecting to a computer or laptop For many presentations, the only connection you ll need is between your computer and the projector; see page 10. Connecting to video sources You can connect the projector to a DVD player, VCR, camcorder, laser disc player, digital camera, or another type of video source. You can even connect a video source and computer at the same time and switch between the two; see page 18. Using the remote control You can use the remote control to switch between input sources, zoom into your image, and control other projector features. To use the remote control as a wireless mouse, you ll need to connect one of the projector mouse cables. Then you can click through your presentation from up to 32 feet away. See page 31 for instructions on using the remote control. Including sound in your presentation If your presentation includes sound, you can connect an audio cable to use the projector s built-in speaker. See the instructions for your input source in Connecting to a Computer on page 10 and/or Connecting to Video Sources on page 18. If you need more volume, you can also connect the projector to external speakers or a public address system; see page 21. Setting Up the Projector 9

15 Connecting to a Computer Follow the instructions in these sections for the type of computer you need to connect: Connecting to a PC Laptop below Connecting to a PC Desktop Computer on page 12 Connecting to a PowerBook on page 14 Connecting to a Macintosh Desktop Computer on page 16 Connecting to a PC Laptop To connect the projector to your laptop, notebook computer, or hand-held device, you need to use the computer cable. If you ll be using the remote control as a wireless mouse, you need to connect a mouse cable. If you ll be using audio through the projector s speakers, you need to connect an audio cable (not included with the projector). Connecting the Computer Cable Before you start, turn off your laptop and the projector. 1. Connect one end of the computer cable to the projector s Computer port. note Laptop configurations vary. See your manual if you re not familiar with the ports on your laptop. 2. Connect the other end of the cable to your laptop s video-out or monitor port. 3. Tighten the screws on the connectors. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. 10 Setting Up the Projector

16 Connecting the Mouse Cable To use the remote control as a wireless mouse, you need to connect a mouse cable: either the round PS/2 or the flat USB mouse cable. 1. Connect one end of the appropriate mouse cable to the PS/2 Mouse/Com port or the USB Mouse port on the projector. note See page 32 for instructions on using the remote control as a wireless mouse. You can use the USB port for a mouse only on systems configured originally with Windows 98 or If you upgraded your system from Windows 3.1 or 95, the USB port may not work as a mouse port. 2. Connect the other end to your laptop s external mouse or USB port. 3. If necessary, configure your laptop to work with an external mouse. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Connecting the Audio Cable If you ll be using audio through your projector s speakers, you need to connect a stereo, mini-jack audio cable (not included). 1. Connect one end of the audio cable to the Audio In port on the projector. note If you need additional volume (in a large auditorium, for example), you can also connect external speakers or a public address system to the projector. See page 21 for instructions. 2. Connect the other end to the laptop s headphone or audio out jack. Setting Up the Projector 11

17 If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Connecting to a PC Desktop Computer To connect the projector to your PC desktop computer, you need to use the computer cable. If you ll be using the remote control as a wireless mouse, you need to connect a mouse cable. If you ll be using audio through the projector s speakers, you need to connect an audio cable (not included with the projector). Connecting the Computer Cables Before you start, turn off your projector and computer. 1. Disconnect the monitor cable from the monitor port on the back of your computer. 2. Connect one end of the computer cable to the projector s Computer port. 3. Connect the other end of the computer cable to your computer s video (monitor) port. 4. Tighten the screws on the connectors. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. 12 Setting Up the Projector

18 Connecting the Mouse Cable To use the remote control as a wireless mouse, you need to connect a mouse cable: either the round PS/2 or the flat USB mouse cable. 1. Connect one end of the appropriate mouse cable to the PS/2 Mouse/Com port or the USB Mouse port on the projector. note See page 32 for instructions on using the remote control as a wireless mouse. You can use the USB port for a mouse only on systems configured originally with Windows 98 or If you upgraded your system from Windows 3.1 or 95, the USB port may not work as a mouse port. 2. Connect the other end to the mouse port on your computer. 3. Tighten the screws on the connectors. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Connecting the Audio Cable If you ll be using audio through your projector s speakers, you need to connect a stereo, mini-jack audio cable (not included). 1. Connect one end of the audio cable to the Audio In port on the projector. note If you need additional volume (in a large auditorium, for example), you can also connect external speakers or a public address system; see page 21 for instructions. 2. Connect the other end of the audio cable to the speaker or audio out port on the computer s sound card. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Setting Up the Projector 13

19 Connecting to a PowerBook You can connect your projector to most PowerBooks that support an external monitor. To connect the projector to your PowerBook, you need to use the computer cable. If you ll be using the remote control as a wireless mouse, you need to connect a mouse cable. If you ll be using audio through the projector s speakers, you need to connect an audio cable (not included with the projector). Connecting the Computer Cable Before you start, turn off your PowerBook and the projector. 1. Connect one end of the computer cable to the projector s Computer port. 2. Connect the other end to your PowerBook s monitor port. 3. Tighten the screws on the connectors. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. 14 Setting Up the Projector

20 Connecting the Mouse Cable To use the remote control as a wireless mouse, you need to connect the USB mouse cable. 1. Connect one end of the USB mouse cable to the USB Mouse port on the projector. note Your Macintosh must be using Macintosh OS 8.51 or later for USB support. See page 32 for instructions on using the remote control as a wireless mouse. 2. Connect the other end to the USB port on your PowerBook. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Connecting the Audio Cable If you ll be using audio through your projector s speakers, you ll need to connect a stereo, mini-jack audio cable (not included). 1. Connect one end of the audio cable to the Audio In port on the projector. note If you need additional volume (in a large auditorium, for example), you can also connect external speakers or a public address system; see page 21 for instructions. 2. Connect the other end to the audio out port on your PowerBook. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Setting Up the Projector 15

21 Connecting to a Macintosh Desktop Computer To connect the projector to your desktop Macintosh, you need to use the computer cable. If you ll be using the remote control as a wireless mouse, you need to connect a mouse cable. If you ll be using audio through the projector s speakers, you need to connect an audio cable. Connecting the Computer Cable Before you start, turn off the projector and computer. 1. Disconnect the monitor cable from the video (monitor) port on the back of the Macintosh. 2. Connect one end of the computer cable to the projector s Computer port. 3. Connect the other end of the computer cable the video (monitor) port on the Macintosh. 4. Tighten the screws on the connectors. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. 16 Setting Up the Projector

22 Connecting the Mouse Cable To use the remote control as a wireless mouse, you need to connect the USB mouse cable. 1. Connect one end of the USB mouse cable to the USB Mouse port on the projector. note Your Macintosh must be using Macintosh OS 8.51 or later for USB support. See page 32 for instructions on using the remote control as a wireless mouse. 2. Connect the other end to the USB port on your Macintosh. If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. Connecting the Audio Cable If you ll be using audio through your projector s speakers, you ll need to connect a stereo, mini-jack audio cable (not included). 1. Connect one end of the audio cable to the Audio In port on the projector. note If you need additional volume (in a large auditorium, for example), you can also connect external speakers or a public address system; see page 21 for instructions. 2. Connect the other end of the audio cable to the audio-out port on your Macintosh. Setting Up the Projector 17

23 If you don t need to make any other connections, you can plug in and turn on your equipment; see page 21 for instructions. note You can t use the projector with a cable TV-style F connector. Connecting to Video Sources You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, or any other compatible video source to your projector. You can connect one video source and a computer at the same time, and easily switch between them. The projector supports HDTV, NTSC, PAL, and SECAM formats, and automatically detects the one you re using. Connecting the RCA A/V Video Cable Before you start, make sure the projector and your VCR or other video source are turned off. 1. Connect the yellow plug on one end of the A/V cable to the projector s yellow Video jack. 2. Connect the other yellow plug to the video-out jack on your video source. 3. Connect the red and white plugs on the A/V cable to the projector s Audio L (white) and R (red) jacks. RCA audio/video cable 4. Connect the red and white plugs at the other end of the cable to the corresponding audio output jacks on your video source. 18 Setting Up the Projector

24 Connecting an S-Video Cable If your video source has an S-Video jack (as shown with an S-Video plug to the right), you can use it to project a higher quality video image. However, you ll need an S-Video cable, which may be included with your video source or may be purchased from an electronics or video store. Before you start, make sure the projector and your VCR or other video source are turned off. 1. Insert one end of the S-Video cable into the projector s S-Video connector RCA audio/video cable S-Video cable (not included) 2. Insert the other end into the S-Video output port of your video source. 3. Connect the red and white plugs on the A/V cable to the projector s Audio L (white) and R (red) jacks. 4. Connect the red and white plugs at the other end of the cable to the corresponding audio output jacks on your video source. Connecting a Component Video Cable You can connect a component video cable to project images from a DVD player or HDTV video source. You ll need the RCA A/V cable (included with your projector) and a component video cable (optional; available from EPSON as described on page 6). Setting Up the Projector 19

25 Before you start, make sure the projector and your component video source are turned off. 1. Connect the red and white plugs on the A/V cable to the projector s Audio L (white) and R (red) jacks. component video cable (not included) RCA audio/video cable 20 Setting Up the Projector 2. Connect the red and white plugs at the other end of the A/V cable to the corresponding audio output jacks on your video source. 3. Connect the 15-pin connector on the component video cable to the projector s computer port. 4. Connect the green, blue, and red jacks on the other end of the cable to these ports on your component video source: Y (green) Pb or Cb (blue) Pr or Cr (red) port. 5. Select the correct settings for your component video source by selecting the following in the projector s Video menu (as described on page 38): If you connected the projector to a DVD player, select YCbCr as the Input Signal setting. If you connected an HDTV source or if your DVD player supports YPbPr, select YPbPr as the Input Signal setting and 16:9 as the Aspect Ratio setting.

26 Connecting to External Speakers or a PA System The projector s speaker is loud enough for most small- or medium-size rooms. For large rooms or maximum volume, you can connect the projector to external speakers or a public address (PA) system. You ll need an RCA-to-3.5mm stereo audio cable, which may be included with your sound system or may be purchased from an electronics store. Before you start, make sure the projector and speakers or PA system are turned off. 1. Connect the cable s 3.5 mm stereo miniplug to the projector s Audio Out jack. note The projector s internal speaker is disabled when you use an external audio system. 2. Connect the RCA plugs to the speaker or PA system. Insert the cable s red plug into the Audio R jack and the white plug into the Audio L jack. Setting Up the Projector 21

27 22 Setting Up the Projector

28 2Using the Projector Once you ve connected the projector to your computer or other equipment (as described in Chapter 1), you re ready to turn on the projector, adjust the image, and give your presentation. This chapter covers the following: Turning on the projector and other equipment Adjusting your image Using the remote control Controlling audio and video Highlighting your presentation Shutting down the projector and other equipment note If you have more than one source connected, you may have to switch to the one you want to use, as described on page 25. Turning On Your Equipment Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1. Then plug in and turn on your equipment, as described below. Follow these steps to plug in and turn on your equipment: 1. If you re projecting video, first plug in and turn on your VCR, DVD player, or other video source. (If you re projecting from a computer, go to step 2.) 2. To turn on the projector, first connect one end of the power cord to the projector s power inlet on its left side. Using the Projector 23

29 3. Connect the other end to a grounded electrical outlet. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children. note Windows only: If you see a New Hardware Found message saying that Windows has found a plug-and-play monitor, click Cancel. The Power light on the projector turns orange, indicating that the projector is receiving power and is in sleep mode, but is not yet turned on. 4. Remove the lens cap. 5. Press the red Power button on top of the projector. (You can also turn on the projector using the remote control, but you must turn on the remote control first; see page 31.) The Power light flashes green and then stays on. You see a blue screen with the message No Signal displayed. 6. If you re projecting images from a computer, turn on your computer. In a few moments, you should see your computer display projected. (If a projected image fails to appear, see the next section for help.) 7. If you re projecting video, press the Play button. (If a projected image fails to appear, see the next section for help.) Once you see your image, turn to page 27 for instructions on focusing and making other image adjustments. When you re done with your presentation, shut down the projector as described on page 36. Shutting down the projector correctly prevents premature lamp failure and possible damage to the projector from overheating. 24 Using the Projector

30 What To Do If You See a Blank Screen If you see a blank screen or a blue screen with the message No Signal after turning on your computer or video source, do one of the following: Make sure the cables are connected correctly, as described in Chapter 1. Make sure the Power light is green and not flashing and the lens cap is off. If you ve connected more than one input source, you may need to press the Source button on top of the projector or the Computer, Video, or S-Video button on the remote control to select the source you want to use. (Allow a few seconds for the projector to sync up after pressing the button.) Source button Computer, Video, and S-Video buttons Try restarting your computer. If you still don t see an image and you re using a PowerBook, see page 26 for additional steps. If you re using a PC laptop, see page 27. Using the Projector 25

31 If You re Using a PowerBook... You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Control Panels, then click Monitors and Sound. 2. Click the Arrange icon. Click here Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other. If this option isn t available, you may need to select one of the Simulscan resolution settings. Click the Monitor icon, then select a Simulscan resolution as shown. (Allow a few seconds for the projector to sync up after making the selection.) Click here Select a Simulscan resolution 26 Using the Projector

32 If You re Using a PC Laptop... Press the function key that lets you display on an external monitor. It s often labelled with an icon such as but it may be labelled CRT/LCD. You may have to hold down the Fn key while pressing it. Check your laptop s manual or online help for details. On most systems, the or CRT/LCD key lets you toggle between the LCD screen and the projector, or display on both at the same time. Allow a few seconds for the projector to sync up after pressing it. Depending on your computer s video card, you might need to use the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer s documentation or online help for details. Check your computer s video resolution and scan frequency to see if they are supported, as listed on page 62. You may need to adjust your computer s resolution and scan frequency to match one of the modes listed. Adjusting Your Image Once you see your image, you ll need to make certain adjustments: To focus your image, see below. To resize or zoom into your image, see page 28. To raise or lower the image, see page 29. If the image isn t square, see page 30. If the projected image is flickering or noisy, see page 30. Focusing Your Image Rotate the focus ring to sharpen the image. focus ring note If the image from your computer is still out of focus, you can increase the clarity by pressing the Auto button on the remote control. This optimizes the projector s tracking, sync, and position settings. (You can also adjust these settings using the projector menus; see Chapter 3.) Using the Projector 27

33 Adjusting the Image Size You can adjust your image size using the Wide/Tele button on the projector or zoom into a portion of the image using the E-Zoom button on the remote control. Using the Wide/Tele Button To enlarge or reduce your image size in small increments, use the Wide/Tele button on the projector. Press the T side of the button to reduce the image size, or the W side of the Wide/Tele button to enlarge the image to full size. note You can always move the projector closer to or farther from the screen to adjust the image size. Wide/Tele button Enlarge W T Reduce W T Zoom in or out Adjust position of zoomed portion Using the E-Zoom Button If you want to zoom in on a portion of the image, use the E-Zoom and Enter buttons on the remote control. Press the + side of the E-Zoom button to zoom into your image in small increments. Press the side to zoom out. To position the zoomed image on the screen, press the top, bottom, left, or right side of the Enter button on the remote control. (Press Esc to return your image to its original size and turn off E-Zoom.) E-Zoom button Enter button top + Zoom in left right Zoom out bottom 28 Using the Projector

34 Adjusting the Image Height If your image is too low, you can raise it by extending the projector s feet. 1. Stand behind the projector. Pull up the blue foot release levers and lift the front of the projector. This unlocks the feet. caution To avoid damaging the lens, do not lift the projector by the lens. 2. Raise or lower the front of the projector as necessary. 3. Once the image is positioned where you want it, release the levers to lock the feet into position. 4. To fine-tune the height, rotate the feet clockwise to raise the projector and counterclockwise to lower it. note If the image shape is not square after adjusting its position, see the next section for a solution. counterclockwise to lower it clockwise to raise it Using the Projector 29

35 Adjusting the Image Shape If the projected image isn t square or has a keystone shape, do one or more of the following: If your image looks like or, you ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely. If your image looks like or, press the + or side of the Keystone button to correct the shape of the image. The Keystone button corrects up to a 15 tilt. After correction, your image will be slightly smaller. Keystone button note If the image is noticeably uneven after keystone correction, reduce the Sharpness setting using the Video menu; see page 39 for instructions. You can also perform electronic keystone correction using the projector s Setting menu. See page 42 for instructions. note You can also increase computer image clarity by pressing the Auto button on the remote control to optimize the tracking, sync, and position settings. Turn off E-Zoom and A/VMute before using the Auto button; see page 28 and page 34. Adjusting the Image Quality You may need to adjust the projector s Tracking and Sync settings if your computer image has any of these quality problems: Flashing or blurry image Vertical or horizontal stripes Only a portion of the image is displayed See Chapter 3 for instructions on adjusting these settings in the projector s Video menu. 30 Using the Projector

36 Using the Remote Control The remote control lets you access projector features from anywhere in the room up to 32 feet away. You must also be within a 30 horizontal and a 15 vertical angle of the infrared receiver on the front of the projector. You can use the remote control to turn the projector on and off, zoom the image, display the projector menus, and other uses.if you connected a mouse cable to the projector, you can also use the remote control as a wireless mouse to run your presentation. See page 32 for instructions. Installing the Remote Control Batteries The remote control operates the projector and lets you access its setup menus. You can also use it as a wireless mouse. Follow these steps to install the batteries: 1. Press the tab to release the battery cover and lift it up to remove it. 2. Insert the two AA batteries included with the projector as shown. infrared receiver for remote control note You can aim the remote control at your projection screen and reflect the signal back into the sensor on the front of the projector, but this shortens the operating distance of the remote control. caution When replacing batteries, take the following precautions: Replace batteries as soon as they run out. Do not mix old and new batteries. 3. Replace the battery cover. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. Remove batteries if you will not be using the remote for a long period of time. Using the Projector 31

37 power indicator light R/C switch note When you connect the mouse cable, your computer mouse is disabled and you can t use another external mouse with your desktop. However, you may still be able to use the built-in mouse pointer on your laptop. Operating the Projector with the Remote Control 1. Push up the R/C switch on the side of the remote control to turn it on. 2. Point the remote at the front of the projector or at the screen. 3. Press the button for the function you want to use. The light next to the Power button on the remote control flashes briefly. (If it doesn t flash, you may have inserted the batteries incorrectly or need to change the batteries; see page 31 for instructions.) The projector may not respond to remote control commands in these conditions: You are too far away or not within a 30 horizontal or 15 vertical angle of the projector s sensor The R/C switch on the right side of the remote control is in the OFF position (the remote control is turned off) Batteries are weak Bright ambient light, fluorescent light, or direct sunlight is shining into the remote control sensor Equipment emitting infrared energy (such as a radiant room heater) is nearby and interfering with the sensor Using the Remote Control as a Wireless Mouse Using the remote control as a wireless mouse gives you more flexibility; you don t need to stay near your computer or the projector to run your presentation. To use the remote control as a mouse, you must first connect a mouse cable between your computer and the projector. See Chapter 1 for instructions. 32 Using the Projector

38 Follow these instructions to use your remote control as a wireless mouse: Aim the remote at the screen or at the receiver on the front of the projector. To move the mouse pointer on the screen, press the edges of the Enter button with your thumb, as you would to move a trackball. To click, press down on the center of the Enter button. To double-click, press down twice on the Enter button. To click and drag, press down on the Enter button and then tilt it in the direction you want to drag. To right-click, press the Esc button. To change slides in a PowerPoint presentation (in Slide Show mode), press down on the Enter button. Controlling Audio and Video While giving your presentation, you may want to switch between picture sources, temporarily turn off or freeze the picture, or adjust the volume. Make sure you ve first set up your projector and connected your audio or video source as described in Chapter 1. Switching Between Picture Sources You can connect the projector simultaneously to one computer source and one video source. Then you can use the buttons on the projector or remote control to switch between them. Press the Source button on the projector to switch between computer, S-video, and composite video sources. Press the Computer, Video, or S-Video button on the remote control to select the source you want to use. After you select a source, the screen goes dark for a moment before the image appears. Press edges to move the pointer Press center to left-click Press here to right-click note If you swapped the mouse button functions on your computer mouse, the Enter and Esc buttons on the remote control also swap functions. Select Computer, Video, or S-Video Using the Projector 33

39 Freezing the Picture You can use the remote control to freeze the current picture on the screen. Press the Freeze button to freeze the current image on the screen. The sound will continue. Press the Freeze button again to re-start it. Freeze picture Turn off picture and sound Adjust volume Turning Off the Picture and Sound You can use the A/VMute button on the remote control to turn off the image and sound. This is lets you temporarily re-direct your audience s attention without the distraction of a bright screen. To turn off the picture, press the A/VMute button. The screen goes dark. To turn the image back on, press the A/VMute button again. You can change the color of the blank screen displayed while A/VMute is on using the Setting menu; see page 38 for instructions. Adjusting Sound Volume Using the remote control, you can adjust the volume of your video or computer sounds. To increase the volume, press on the right (+) side of the Volume button. To decrease the volume, press on the left ( ) side of the Volume button. 34 Using the Projector

40 Highlighting Your Presentation The projector s highlighting tools let you emphasize areas on the screen using the numbered buttons on the remote control. This is useful for annotating your presentation slides or calling attention to their most important points. These tools are available: Arrow or cursor stamp (button 1) Horizontal bar (button 2) You can use the Effect menu to customize the highlighting tools. See page 41 for instructions. Using the Cursor/Stamp Arrow You can use the cursor stamp tool as a pointer and place cursor stamps anywhere on your screen. 1. To activate the cursor stamp, press the 1 button on the remote control. A icon appears on the screen. 2. Press the side of the Enter button to move the pointer wherever you want it. 3. To paste the pointer on the screen, press down in the center of the Enter button. You can then continue to move another pointer around the screen and paste it wherever you want. 4. To erase the pointers pasted on the screen, press the 3 button. 5. To cancel the cursor stamp feature, press the Esc button. Drawing a Horizontal Bar You can place a horizontal bar on the screen and move it up or down to highlight your presentation points. 1. To activate the bar tool, press the 2 button on the remote control. A magenta horizontal bar appears in the middle of the screen. 2. Press the top or bottom of the Enter button to move the bar up or down the screen. 3. To erase the bar from the screen, press the Esc button. Horz. bar Cursor stamp Move bar or cursor note You can use the projector s Effect menu to select a different cursor stamp shape and size. See page 41 for instructions. note You can change the width and color of the bar using the projector s Effect menu. See page 41 for instructions. Using the Projector 35

41 note If sleep mode is enabled and the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters sleep mode. This conserves electricity, cools the projector, and extends the life of the lamp. In sleep mode, the Power light is orange. If you are done using the projector, unplug the power cord. If you want to start projecting again, press the Power button on the projector or the remote control. Shutting Down the Projector When you ve finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating. 1. If you ve connected a computer or laptop and it s displaying only through the projector, shut down the computer first; otherwise you won t be able to see your computer s display if you try turning it off after the projector. 2. Press the red Power button on top of the projector or on the remote control. You see a confirmation message. (If you don t want to turn it off, press any other button.) Power button power off confirmation message caution To avoid damaging the projector or lamp, never unplug the power cord when the Power light is green or flashing orange. 3. Press the Power button again. The Power light flashes orange for a couple of minutes as the projector cools down. When the projector has cooled, the orange Power light stays on and the fan shuts off. If you want to turn the projector on again, wait until the orange Power light stops flashing. Then press the Power button. 4. Replace the lens cap, retract the projector feet, and unplug the power cord. Also turn off the remote control, if you were using it. 5. If you re using a VCR or other video source, turn it off after you turn off the projector. 6. Disconnect all equipment, and store the projector in a protective case. 36 Using the Projector