Draco Converter. Media / DVI Converter. User Manual. 238 Series. Edition:

Transcription

1 Draco Converter 238 Series Media / DVI Converter User Manual Edition: IHSE GmbH Maybachstraße Oberteuringen Germany info@ihse.com phone: fax:

2 Media / DVI Converter Copyright All rights reserved. This information may not be reproduced in any manner without the prior written consent of the manufacturer. Information in this document is subject to change without notice. Trademarks All trademark and trade names mentioned in this document are acknowledged to be the property of their respective owners. Disclaimer While every precaution has been taken during preparation of this manual, the manufacturer assumes no liability for errors or omissions. The manufacturer assumes no liability for damages resulting from the use of the information contained herein. The manufacturer reserves the right to change specifications, functions, or circuitry of the product without notice. The manufacturer cannot accept liability for damage due to misuse of the product or due to any other circumstances outside the manufacturer s control (whether environmental or installation related). The manufacturer shall not be liable for any loss, damage, or injury arising directly, indirectly, incidentally, or consequently from the use of this product

3 Contents Contents 1 About This Manual Scope Validity Cautions and Notes Safety Instructions Description Application System Overview Product Range Upgrade Kits Accessories Device Views Model K238-5V Model K238-5VE Model K238-5VS Model K238-5FBNC Status LEDs Installation Package Contents System Setup Example Applications Configuration Infrared Remote Control Control via Keyboard On Screen Display (OSD) Main Menu Item 'Color Settings' Main Menu Item 'Picture Settings' Main Menu Item 'Input Settings' Main Menu Item 'Output Settings' Main Menu Item 'General Settings'

4 Media / DVI Converter 6 Operation Optimization of Picture Settings Optimization of Output Settings Optimization of Input Settings Optimization of Picture Settings Download of DDC Information Download of DDC by Infrared Remote Control Download of DDC via OSD Further DDC settings Serial Interface Specifications Interfaces DVI-D Single Link DVI-I Single Link S-Video (Y/C) SDI Video EGA (D-Sub 9) Composite Video (VBS / CVBS) Component Video (YPbPr) RGB Video Supported Video Modes Serial Control Telegram Structure Examples Connector Pinouts Power Supply Environmental Conditions Size Shipping Weight Troubleshooting Blank Screen Picture

5 Pos: 1 /806-IHSE/Zu diesem Handbuch/ATB_Zu diesem 1 Contents 8.3 General Technical Support Support Checklist Shipping Checklist Certificates CE Declaration Of Conformity North American Regulatory Compliance WEEE RoHS/RoHS Glossary

6 Pos: Media / DVI Converter 1 About This Manual 1.1 Scope This manual describes how to install your Media / DVI Converter, how to operate it and how to perform trouble shooting. 1.2 Validity This manual is valid for all devices listed on the front page. The product code is printed on the base of the devices. 1.3 Cautions and Notes The following symbols are used in this manual: This symbol indicates an important operating instruction that should be followed to avoid any potential damage to hardware or property, loss of data, or personal injury. This symbol indicates important information to help you make the best use of this product. This symbol indicates best practice information to show recommended and optimal ways to use this product in an efficient way

7 Pos: Safety Instructions 2 Safety Instructions To ensure reliable and safe long-term operation of your Media / DVI Converter please note the following guidelines: Installation Only use in dry, indoor environments. Only use the device according to this User Manual. Failure to follow these procedures could result in damage to the equipment or injury to the user or installer. The Media / DVI Converter and the power supply units can get warm. Do not install components in an enclosed space without any airflow. Do not place the power supply directly on top of the device. Do not obscure ventilation holes. Only use power supplies originally supplied with the product or manufacturer-approved replacements. Do not use a power supply if it appears to be defective or has a damaged chassis. Connect all power supplies to grounded outlets. In each case, ensure that the ground connection is maintained from the outlet socket through to the power supply's AC power input. Do not connect the link interface to any other equipment, particularly network or telecommunications equipment. Take any required ESD precautions. In order to disconnect the device completely from the electric circuit, all power cables have to be removed. Repair Do not attempt to open or repair a power supply unit. Do not attempt to open or repair the Media / DVI Converter. There are no user serviceable parts inside. Please contact your dealer or manufacturer if there is a fault

8 Pos: 5 /806-IHSE/Beschreibung/System-Übersicht 1 Media / DVI Converter 3 Description Pos: Application The Media / DVI Converter is used to convert and output video signals of one or more video sources (computer, CPU, camera, DVD player) in DVI- D format. The Media / DVI Converter can be used as a switch between multiple input signals. The Media / DVI Converter can be used to scale video signals to a specific output format

9 Pos: System Overview Description The input ports of the Media / DVI Converter are connected to the video source(s) (e.g. computer, CPU, camera, DVD player, SPS control), using the cables supplied or other suitable video cables. The DVI-D monitor is connected to the output. System Overview 1 Sources (DVD player, computer, camera, SPS control) 2 Media / DVI Converter 3 Monitor See Chapter 4.3, Page 18 for installation examples

10 Pos: Media / DVI Converter 3.3 Product Range Model K238-5V K238-5V-S K238-5VE K238-5VE-S K238-5VS K238-5VS-S K238-5FBNC Description Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) and serial option Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) and Video (Y/C) / Component (YPbPr) / CVBS and CGA / EGA / MDA Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) and Video (Y/C) / Component (YPbPr) / CVBS and CGA / EGA / MDA and serial option Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) and Video (Y/C) / Component (YPbPr) / CVBS and (HD-)SDI Media / DVI Converter for VGA- / DVI-Input (up to 1920x1200) and Video (Y/C) / Component (YPbPr) / CVBS and (HD-)SDI and serial option Media / DVI Converter for RGB- / VGA- / DVI-Input (up to 1920x1200) with a separate 5x BNC RGB-Input The input side of the following KVM extenders corresponds to the Media / DVI Converter K238-5V: K477-xxxxV, L474-xxxxV. Pos: Upgrade Kits Model Description 455-4G 19"/1U rack mount kit to mount up to 4 devices of type K238-5V 474-VRMK 19"/1U rack mount kit to mount up to 3 devices of type K238-5VE, -5VS or -5FBNC 455-1K Mounting plate to mount by screws (type K238-5V) 455-2K Mounting plate to mount by snap on (type K238-5V) 474-VPLATE Mounting plate to mount by snap on or screws (type K238-5VE, -5VS or -5FBNC) The Media / DVI Converters and power supply units become warm and must not be installed in closed rooms with no air circulation. For rackmount installations, at least 0.5U (height unit) is required above the extenders for ventilation

11 Pos: 11 /806-IHSE/Beschreibung/Geräteansichten/238-5v-xx/Typ 1 Neuedings kommt Windows-Installer Description 3.5 Accessories Model 238-BCA 238-BNC 238-EGA 238-IR 238-RCA 238-SDI 238-SV Description Video adapter (BNC connector to Cinch connector) RGB cable (2.0 m, 5x BNC connector) EGA cable (1.8 m, D-Sub 9 connector) Infrared remote control Component video cable (1.5 m, 3x RCA connector) SDI cable (1.8 m, BNC connector) S-Video cable (3.0 m, Mini-DIN connector, 4 pole) 260-5U International power supply unit VAC / 5VDC / 4 A 436-AA 436-DB1 436-ID VGA cable (1.8 m, VGA connector to DVI-I connector) RGB / DVI cable (0.2 m, 5x BNC connector to DVI-D connector) DVI-D cable (1.8 m, DVI-D connector) Pos: Device Views Pos: 10 /806-IHSE/Beschreibung/Geräteansichten/238-5v-xx/Typ Model K238-5V Rear View 1 Connect to 5VDC power supply 2 Input: DVI-I (VGA) 3 Service port 4 IR receiver for remote control 5 Output: DVI-D Front View 1 IR receiver for remote control

12 Pos: 12 /806-IHSE/Beschreibung/Geräteansichten/238-5v-xx/Typ 1 Media / DVI Converter Model K238-5VE Rear View 1 Connect to 5VDC power supply 2 Input: DVI-I (VGA) 3 Service port 4 IR receiver for remote control 5 Output: DVI-D 6 Input: S-Video (Y/C) 7 Input: CVBS 1 or YPbPr (Pr) 8 Input: CVBS 2 or YPbPr (Y) 9 Input: CVBS 3 or YPbPr (Pb) 10 Input: EGA Front View 1 IR receiver for remote control

13 Pos: 13 /806-IHSE/Beschreibung/Geräteansichten/238-5v-xx/Typ 1 Description Model K238-5VS Rear View 1 Connect to 5VDC power supply 2 Input: DVI-I (VGA) 3 Service port 4 IR receiver for remote control 5 Output: DVI-D 6 Input: S-Video (Y/C) 7 Input: CVBS 1 or YPbPr (Pr) 8 Input: CVBS 2 or YPbPr (Y) 9 Input: CVBS 3 or YPbPr (Pb) 10 Input: CVBS 4 11 Input: (HD-)SDI Front View 1 IR receiver for remote control

14 Pos: 14 /806-IHSE/Beschreibung/Diagnose 1 Media / DVI Converter Model K238-5FBNC Rear View 1 Connect to 5VDC power supply 2 Input: DVI-I (VGA) 3 Service port 4 IR receiver for remote control 5 Output: DVI-D 6 Input: RGB (red) 7 Input: RGB (green) 8 Input: RGB (blue) 9 Input: RGB (H-/Compos. Sync, RGBs) 10 Input: RGB (V-Sync) Front View 1 IR receiver for remote control

15 Pos: Status LEDs Description The Media / DVI Converter is fitted with a multi-color LED to indicate connection status: K238-5V K238-5VE / -VS / -FBNC Front View Front View LED 1: Connection and Video Status LED color Description for the input Description for the output Red No input signal Monitor detected Dark Red Resolution not supported Monitor not detected Green Active video signal Monitor not detected Blue No input signal Monitor detected Violet Resolution not supported Monitor detected Light blue Active video signal Monitor detected

16 Media / DVI Converter 4 Installation Pos: 16 /806-IHSE/Installation/Lieferumfang Package Contents Your Media / DVI Converter package contains the following items: Media / DVI Converter device 5VDC international power supply unit Country-specific power cord Quick Setup VGA cable (1.8 m, VGA connector to DVI-I connector) Infrared remote control Additional content for K238-5VE: EGA cable (1.8 m, D-Sub 9 connector) Component video cable (1.5 m, 3x RCA connector) S-Video (3.0 m, Mini-DIN connector, 4 pole) Additional content for K238-5VS: SDI cable (2.0 m, BNC connector) Component video cable (1.5 m, 3x RCA connector) S-Video (3.0 m, Mini-DIN connector, 4 pole)

17 Pos: Installation Additional content for K238-5FBNC: RGB cable (2.0 m, 5x BNC connector). If anything is missing, contact your dealer. Pos: 17 /806-IHSE/Installation/System System Setup First time users are recommended to setup the system with the CPU Unit and the CON Unit in the same room as a test setup. This will allow you to identify and solve any cabling problems, and experiment with your system more conveniently. Please verify that interconnect cables, interfaces and handling of the devices comply with device specifications (see Chapter 7, Page 42). 1. Switch off all devices. 2. Connect the monitor to the Media / DVI Converter. 3. Connect the source (e.g. computer, video camera or control unit) to the Media / DVI Converter with the cables supplied. Please ensure the cables are not strained. 4. Connect the supplied 5VDC power supply to the Media / DVI Converter. 5. Power up the system. To power up the system, the following sequence is recommended: Monitor Media / DVI Converter source. Always remove the power supply first, before you connect the Media / DVI Converter to a computer for updating purposes

18 Pos: 19 @ 1 Pos: Media / DVI Converter 4.3 Example Applications This section illustrates typical installations of Media / DVI Converters: Media / DVI Converter (Video Input: Composite) 1 Source (observation camera) 2 Media / DVI Converter 3 Monitor Media / DVI Converter (Video Input: S-Video) 1 Source (DVD player) 2 Media / DVI Converter 3 Monitor

19 Configuration 5 Configuration Pos: Infrared Remote Control The Media / DVI Converter can be configured by means of an on-screen display (OSD) in conjunction with infrared remote control to select and configure menu items on the OSD. In the OSD, only the navigation keys of the infrared remote control are functional (red function key, < >, <EXIT>, <ESC> and cursor keys < >, < >, < >, < >). Button Description Open OSD or select menu. Open OSD or select menu

20 Media / DVI Converter Button Description Leave OSD. Leave current menu and open upper menu level. Navigate inside the OSD. Select parameters with cursor keys < > and < >. Read and use DDC from the connected monitor. Execute Auto Configuration (VGA / RGB / EGA input only) Adjust picture contrast / brightness. Reset the Media / DVI Converter to factory default. Reset picture contrast / brightness to factory default

21 Pos: 22 /806-IHSE/Konfiguration/Ansteuerung Tastatur/238_Ansteuerung über 1 Configuration Button Description If more than one converter is used: Select a single device for OSD access. If more than one converter is used: Select all devices for OSD access. Select input signal: VGA, DVI or SDI. Select input signal: Y/C (S-Video) YPbPr (Component Video) RGB EGA Select input signal CVBS 1 3 RCA, (Cinch) or CVBS 4 (BNC)

22 Media / DVI Converter 5.2 Control via Keyboard The Media / DVI Converter can be used in combination with a KVM extender (either standalone or as an onboard version) and can be controlled using a keyboard. The Media / DVI Converter includes a keyboard-controlled Command Mode that can be used to directly activate various functions and to navigate through the On-screen Display (OSD). The Command Mode is entered by a keyboard sequence ('Hot Key') and can be closed using the key <Esc>. Shift and Scroll LEDs on the keyboard will flash when Command Mode is activated. Direct Control The following table contains the keyboard commands for opening and closing Command Mode and for direct control of various converter functions. Function Enter Command Mode (default) Exit Command Mode Configure video settings automatically (only with VGA / RGB / EGA input) Reset the device back to factory settings Direct selection input VGA Direct selection input DVI Direct selection input SDI (module dependent) Direct selection input Y/C (S- Video, module dependent) Direct selection input YPbPr (Component Video, module dependent) Direct selection input RGB (module dependent) Direct selection input EGA (module dependent) Keyboard Command 2x <Left Shift> (or 'Hot Key'), <v> <Left Shift> + <Esc> 2x <Left Shift>, <v>, <a> 2x <Left Shift>, <v>, <r> 2x <Left Shift>, <v>, <F1>, <Enter> 2x <Left Shift>, <v>, <F2>, <Enter> 2x <Left Shift>, <v>, <F3>, <Enter> 2x <Left Shift>, <v>, <F4>, <Enter> 2x <Left Shift>, <v>, <F5>, <Enter> 2x <Left Shift>, <v>, <F6>, <Enter> 2x <Left Shift>, <v>, <F7>, <Enter>

23 Pos: 23 /806-IHSE/Konfiguration/238_On-Screen-Display 1 Configuration Function Direct selection input FBAS 1 (module dependent) Direct selection input FBAS 2 (module dependent) Direct selection input FBAS 3 (module dependent) Direct selection input FBAS 4 (module dependent) Keyboard Command 2x <Left Shift>, <v>, <F8>, <Enter> 2x <Left Shift>, <v>, <F9>, <Enter> 2x <Left Shift>, <v>, <F10>, <Enter> 2x <Left Shift>, <v>, <F11>, <Enter> OSD Control The following table contains the keyboard commands for entering and exiting the OSD and for navigation and configuration. Function Open OSD window Close OSD window Navigation down in the menu Navigation up in the menu Menu selection Leave sub menu Change of settings in sub menus or selection of parameter values Keyboard Command 2x <Left Shift>, <v>, <o> <Esc> <Cursor down> <Cursor up> <Enter> <Backspace> <Cursor right> or <Cursor left>

24 Media / DVI Converter 5.3 On Screen Display (OSD) All settings of the Media / DVI Converter can be adjusted via the on screen display (OSD). General Structure of the OSD: The left column shows the range of the main menu, the right column shows the current submenus with the respective configuration options. The various configuration and setting options of the Media / DVI Converter are described below:

25 5.3.1 Main Menu Item 'Color Settings' Configuration This menu offers color specific settings and configurations for the Media / DVI Converter. Menu View 'Color Settings' Menu Item Brightness Contrast Hue Saturation Sharpness Description Adjust brightness of the picture Adjust contrast of the picture Change and adjust hue of the picture (only selectable for video input signals). Adjust saturation of the picture (only selectable for video input signals). Adjust sharpness of the picture Color Open submenu 'Color' (see Chapter , Page 26)

26 Media / DVI Converter Submenu 'Color' This submenu offers advanced color settings for the picture (VGA / RGB / EGA input only). Menu View 'Color' Menu Item Auto Color Color Temperature srgb Red Green Blue Description Adjust color values automatically Adjust color temperature of the picture Activate the use of the standard RGB color range (Color optimization for tube monitors). Adjust red color range Adjust green color range Adjust blue color range

27 5.3.2 Main Menu Item 'Picture Settings' Configuration This menu offers specific picture settings at the Media / DVI Converter. Menu View 'Picture Settings' Menu Item Auto Configuration Phase Description Configure picture settings automatically (VGA / RGB / EGA input only). Adjust pixel phase i.e. the best position for the analog / digital conversion within one pixel (VGA / RGB / EGA input only). Example for incorrect pixel phase

28 Media / DVI Converter Menu Item Clock Description Adjust pixel clock. The pixel clock shows the maximum number of the pixels that are horizontally displayable. Non-visible and inactive pixels are counted in (VGA / RGB / EGA input only). Example for a wrong pixel clock. Width Height Display Control Adjust width of the picture with the number of pixels. Adjust height of the picture with the number of pixels. Open submenu 'Display Control' (see Chapter , Page 29)

29 Submenu 'Display Control' Configuration This submenu offers control options for the display of the picture. Menu View 'Display Control' Menu Item Display Image Aspect Ratio Zoom Description Select display option: 'Auto': Scale picture automatically to the maximum value 'Aspect': Adjust aspect ratio manually '1:1': Show picture in original size with a black border 'Panoramic': Scale picture to a non-linear value (only if there is video input) Select aspect ratio: 'Auto', '4:3', '14:9', '16:9' or '>16:9' (only if 'Display Image' is set to 'Aspect Ratio'). Zoom picture and determine position of enlargement (not available in combination with onboard DVI-I extenders)

30 Media / DVI Converter Main Menu Item 'Input Settings' This menu offers specific settings for Media / DVI Converter inputs. Menu View 'Input Settings' Menu Item Input Select Description Select input signal Channel For CVBS input signal: Select Composite channel. For EGA input: Select EGA, CGA or MDA input signal. Select Resolution Sync Options Video Input Select video mode compatible to input signal (see Chapter 7.2, Page 44 for supported video modes). Save settings by leaving the menu (monitor goes blank for a short time). Select type of synchronization of the RBG signal. The type depends from the incoming RGB signal. 'Auto': Automatic adjustment 'Composite (CS)' or 'Sync On Green (SOG)': Manual adjustment in case of picture failures (VGA / RGB input only) Display of selected video mode

31 5.3.4 Main Menu Item 'Output Settings' Configuration This menu offers specific settings for the output of the Media / DVI Converter. Menu View 'Output Settings' Menu Item Output Resolution Display Position Video Output Description Select output resolution: 'DDC': Use preferred resolution of the monitor's DDC at the output 'Select': Select from predefined output resolutions in the menu item 'Resolution' '1:1': Use input resolution as output resolution Note: The option "DDC" is not available in onboard DVI-I extenders. If 'Output' is set to 'Select': Select from predefined output resolutions. A higher resolution can be selected at any time. If you select a lower resolution, the number of output pixels needs to comply with the following rule: Horizontally: At least 50% Vertically: At least 33% (Not available with onboard DVI-I extenders.) Adjust position of picture manually Display of the selected output resolution

32 Media / DVI Converter Graphic contents with up to 2 mega pixels are scalable (1920x1080). For the scaling of the 1920x1200 resolution, restrictions apply and the video will be transmitted 1:1, if applicable. If you scale resolutions of 1280x1024 or higher, there will be a reduction of color depth to 16 bit YCbCr

33 5.3.5 Main Menu Item 'General Settings' This menu offers general settings for the Media / DVI Converter. Configuration Menu View 'General Settings' Menu Item Description DDC Open submenu 'DDC' (see Chapter , Page 34). Miscellaneous Device Address Manage Settings T-Adjust Open submenu 'Miscellaneous' (see Chapter , Page 35). Assign device ID. The device ID clearly identifies the device for the infrared remote control so that settings can be made for a specific device only. Write the existing device settings on the internal memory of the Media / DVI Converter ('Save'). These settings can be loaded again if required ('Load'), e.g. after a firmware update. Compensate picture failures due to device temperature Save device settings if you have made extensive settings or if you want to perform a firmware update

34 Media / DVI Converter Submenu 'DDC' This submenu offers DDC specific settings. DDC information is relevant to output settings for computer or CPU connection. Menu View 'DDC' Menu Item Read DDC Change DDC Factory DDC MON: DEV: Description Use the monitor DDC as the device DDC and save it as DVI or VGA DDC. Save the device DDC as DVI or VGA DDC Use default DDC 'VGA2DVI' as device DDC Display of name and type of monitor DDC Display of name and type of the device's DDC that is provided at the DVI-I input by the Media / DVI Converter. When saving the DDC as DVI or VGA DDC, the selected type of DDC must match the video signal of the source (VGA or DVI) (see Chapter 5.3.3, Page 30: Menu item 'Input Select')

35 Configuration Submenu 'Miscellaneous' This submenu offers various device specific settings. Menu View 'Miscellaneous' Menu Item Auto Adjust Refresh Rate Video Processing VBI Processing Description Activate or deactivate the automatic configuration of picture settings after changing the video mode. Change refresh rate if output is set to 'DDC'. Not used Not used OSD Configuration Configure OSD display on screen. Factory Reset Reset device to factory default (confirmation dialog)

36 Pos: Pos: Media / DVI Converter Submenu 'OSD Configuration' This submenu offers various settings for the OSD display. Menu View 'OSD Configuration' Menu Item OSD Timer OSD Position Description Activate and select time of inactivity after which OSD is closed automatically. Adjust vertical and horizontal OSD position on screen. OSD Transparency Adjust OSD transparency OSD Zoom Activate scaling of OSD display

37 Operation 6 Operation Pos: 25 /806-IHSE/Betrieb/Optimierung der Optimization of Picture Settings All common video modes are pre-installed in an internal table of the Media / DVI Converter. If the input signal corresponds to one of these video modes, the signal will be automatically detected and the picture will be displayed. If picture quality is not an optimal or no picture is displayed, proceed as follows: 1. Optimize the output settings (see Chapter 6.1.1, Page 37). Thus, the picture display will be adapted to the properties of the monitor. 2. Optimize the input settings (see Chapter 6.1.2, Page 38). Check if the automatically detected video mode corresponds to your input signal. Alternatively, you can manually select the most suitable video mode, even if you have an unknown input signal. 3. Optimize the picture settings for your input signal (see Chapter 6.1.3, Page 39). In the unlikely event that the picture cannot be optimized using the controls provided, please fill in and return the video mode questionnaire (Download) so that a customer specific video mode can be created Optimization of Output Settings 1. For an analog input signal, display a picture with as much detail as possible on your graphic source, e.g. a text with black letters on a white ground (or vice versa). 2. Open the OSD with the infrared remote control. 3. Select 'Output Settings' in the main menu (see Chapter 5.3.4, Page 31). 4. Select the output resolution in the menu item 'Output': Select 'DDC' to use the preferred resolution of the monitor DDC. If the preferred resolution of the device DDC does not result in an optimal picture, select 'Factory' and from the menu item 'Resolution' the most suitable resolution for the monitor. 5. Exit the OSD. A window appears to save settings. This may take a few seconds. 6. Save the settings

38 Media / DVI Converter Optimization of Input Settings For certain analog input signals (VGA / RGB / EGA), if picture quality is not optimal or no picture is displayed, proceed as follows: 1. Open the OSD with the infrared remote control. 2. Select 'Input Settings' in the main menu (see Chapter 5.3.3, Page 30). 3. Test the recommended resolutions that are listed in the menu item 'Select Resolution'. The menu item is inactive, if there is only one recommended resolution. 4. Run the automatic picture adjustment: Select 'Picture Settings' in the main menu (see Chapter 5.3.2, Page 27). Select the menu item 'Auto Configuration'. Thereby picture size might change. 5. Check the test picture: If the vertical lines are displayed clearly, without smear or tremble, the setting has been successful. 6. Exit the OSD. A window appears to save settings. This can take a few seconds. 7. Save the settings

39 6.1.3 Optimization of Picture Settings Operation Should Auto Configuration fail to provide the optimal picture, it can be adjusted manually by following this procedure: 1. Select 'Picture Settings' in the main menu. 2. Modify the values in the menu items 'Clock' and 'Phase' until all picture corruption has disappeared. 3. If the picture is displaced: Select the menu item 'Display position' in the main menu item 'Output Settings' and position the picture in the upper left corner of the monitor. Select the menu items 'Width' and 'Height' in the main menu item 'Picture Settings' and modify the values for width and height of the picture until the monitor is completely filled by the picture. 4. Exit the OSD. A window appears to save settings. This can take a few seconds. 5. Save the settings. Pos: 26 /806-IHSE/Betrieb/Laden von Download of DDC Information Loading of DDC information is only relevant if you want to connect a DVI or VGA source. By default, the factory DDC information is reported to the source (computer, CPU). If these settings do not lead to an optimal picture, the DDC information of the connected monitor can be downloaded and stored internally. There are two options to load the DDC information of the connected monitor: By means of the infrared remote control (see Chapter 6.2.1, Page 40). By means of the 'Read DDC' command in the OSD (see Chapter 6.2.2, Page 40)

40 Media / DVI Converter Download of DDC by Infrared Remote Control 1. Press the <DDC> button on your infrared remote control. 2. Save the DDC as DVI or VGA DDC matching the input video signal. The DDC information of the connected monitor is saved in the Media / DVI Converter in the selected format. The source (computer, CPU) can read the DDC information of the monitor and display the available video resolutions Download of DDC via OSD 1. Open the OSD with the infrared remote control. 2. Select 'General Settings' in the main menu (see Chapter 5.3.5, Page 33). 3. Select the menu item 'Read DDC' in the submenu 'DDC'. Select 'DDC' in the menu item 'Factory DDC' to receive the default DDC information. 4. Save the DDC as DVI or VGA DDC matching the input video signal. The DDC information of the connected monitor is saved in the Media / DVI Converter in the selected format and is displayed at the bottom of the OSD menu under 'DEV:'. The source (computer, CPU) can read the DDC information of the monitor and display the available video resolutions Further DDC settings If there are special requirements, DDC information can be imported from or exported to the device. Therefor, please connect the device to a computer via mini USB cable. 1. Remove 5VDC power supply from the Media / DVI Converter. 2. Connect Media / DVI Converter via mini USB cable to a computer. 3. Connect the 5VDC power supply back to the device. The Media / DVI Converter is now available as a flash drive at the computer

41 Pos: 27 /806-IHSE/Betrieb/Serielle 1 Pos: 28 /806-IHSE/Technische Daten/UEB_Technische 1 Export of DDC Information Operation 4. Now you can use the DDC files "DDC-MON.BIN" of the monitor and "DDC-DEV.BIN" of the Media / DVI Converter by copying them to a local data storage device. To open the binary file, you have to install a suitable software, e.g. WinDDC Writer (Download), on your computer. Import of DDC Information 5. Copy special DDC information as a binary file to the flash drive of the Media / DVI Converter. The existing DDC information in the file "DDC-DEV.BIN" will be overwritten. 6.3 Serial Interface (Not available in combination with onboard DVI-I extenders.) The Media / DVI Converter can be controlled over a serial interface (RS232). The serial control requires an RS232 adapter. For the control of the Media / DVI Converter via serial interface, certain parameters are used. Set up the following format of the serial data transfer for the communication: KBaud, 8, 1, NO (115.2 KBaud, 8 Data bit, 1 Stop bit, no parity)

42 Pos: 35 /806-IHSE/Technische Daten/Schnittstellen/EGA (D-Sub 1 Media / DVI Converter 7 Specifications Pos: 29 /806-IHSE/Technische Interfaces Pos: 30 /806-IHSE/Technische DVI-D Single Link The video interface supports the DVI-D protocol. All signals that comply with DVI-D Single Link norm can be transmitted. This includes monitor resolutions such as 1920x1200@60Hz, Full HD (1080p) or 2K HD (up to 2048x1152). Data rate is limited to 165 MPixel/s. Pos: 31 /806-IHSE/Technische DVI-I Single Link The video interface supports the DVI-I protocol. All analog (VGA) or digital (DVI) signals that comply to DVI-I Single Link norm can be transmitted. This includes e.g. monitor resolutions such as 1920x1200@60Hz, Full HD (1080p) or 2K HD (up to 2048x1152). Data rate is limited to 165 MPixel/s. Pos: 32 /806-IHSE/Technische @ 1 Transmission of interlaced video signals, such as 1920x1080i, cannot be guaranteed. Pos: 33 /806-IHSE/Technische Daten/Schnittstellen/S-Video S-Video (Y/C) The transmission of the video signal consists of a separate transmission of brightness and color information by two isolated signal and ground wire pairs. The plug connection consists of a 4-pole Mini-DIN connector with an input impedance of 75 Ω. Pos: 34 /806-IHSE/Technische SDI Video The (HD-)SDI video signal is transmitted by a serial digital interface. Transmission is carried out uncoded and uncompressed via a coaxial cable. The voltage level of video signal is 0.8 Vpp

43 Pos: 39 /806-IHSE/Technische Daten/Unterstützte EGA (D-Sub 9) The voltage level is a 5V TTL level. Specifications Transmission of the video signal is carried out via a 9-pole D-Sub connector. Pos: 36 /806-IHSE/Technische Daten/Schnittstellen/Composite Video Composite Video (VBS / CVBS) The (C)VBS signal is transmitted in an unmodulated form and consists of a brightness and synchronization signal, in case of CVBS also of an extra color signal. Transmission of the analog video signal is carried out via a RCA (Cinch) or BNC (bayonet) plug connection. Pos: 37 /806-IHSE/Technische Daten/Schnittstellen/Component Video Component Video (YPbPr) The transmission of the analog video signals is carried out via three RCA connectors, whereby the first connector (Pr) transmits the color spectrum of the red and turquoise color range. The second connector (Y) transmits brightness and synchronization and the third connector (Pb) transmits the yellow and blue color range. Pos: 38 /806-IHSE/Technische RGB Video The video signal consists of R (red), G (green) and B (blue) signals. The voltage level of the video signal is 0.7 Vpp. The green signal can additionally contain the (Composite) synchronization signal. The interface is able to support RGBs and RGBHV video signals. Communication of the video interface is carried out via a coaxial plug connection with a 5x bayonet lock (BNC)

44 Media / DVI Converter 7.2 Supported Video Modes The following table lists the video modes that are recognized by the Media / DVI Converter (see Chapter 5.3.3, Page 30). Video modes in italics will be recognized but may be displayed incorrectly. Video modes for DVI, VGA, EGA and RGB Index Description Hres Vres V-Freq H-Freq Dot Clk 17 CGA(TTL) ,9 15,7 7,2 10 PAL ,0 15,6 8,0 36 MONA S ,4 24,3 14,0 4 AS 230 / 235 / OS ,0 15,6 10,0 5 GBE x ,0 15,6 10,0 18 DCC 555a ,2 15,7 10,0 15 WF ,1 15,6 12,0 6 WF ,0 15,6 12,0 7 WF470 / AS ,0 15,6 12,0 60 WF470 / AS ,1 31,3 24,0 12 GEM 80 graph i ,0 15,6 11,7 24 GEM 80 graph i ,1 15,8 11,9 28 GEM 80 graph i ,5 18,2 12, b ,6 26,0 20,0 8 GBE x ,0 15,6 13,0 9 DISET - 80x ,0 15,6 12,2 19 DCS ,0 15,7 11,4 44 MONA -C ,2 25,8 20,0 61 GEM 80 graph progr ,1 31,3 23,5 64 GEM 80 graph progr ,0 31,5 23,7 79 GEM 80 graph progr ,1 36,4 24,

45 Specifications Index Description Hres Vres V-Freq H-Freq Dot Clk 53 WF ,9 30,6 25,0 22 CGA(TTL) ,9 15,7 14,3 3 CP526/ ,0 15,4 13,1 16 GEM 80 text ,8 15,6 13,0 47 Prokon ,0 27,4 23,0 34 EGA (TTL) ,8 21,9 16,3 162 VGA ,2 31,5 25,2 166 VGA ,9 37,8 31,4 33 IVE ,1 21,8 17,4 30 IVE ,0 20,0 16,1 32 Custom ,9 20,6 16,5 39 ABB MOD ,0 24,8 19,8 35 IVE ,0 21,9 17,8 52 NEC 3D PGC ,6 30,3 25,0 70 XGA ,4 39,3 32,4 37 VGA ,9 24,6 20,9 49 OP 398 K ,0 27,5 22,2 164 VGA ,2 31,5 25,2 168 VGA ,9 37,8 31,4 38 COROS LS-C ,1 25,4 21,7 40 COROS LS-C ,1 25,4 21,7 42 Prokon ,8 25,5 23,1 48 Prokon ,9 27,4 23,0 56 CP526 highres ,0 30,9 26,2 57 CP528 highres ,0 30,9 28,3 59 CP526 highres ,0 31,2 26,

46 Media / DVI Converter Index Description Hres Vres V-Freq H-Freq Dot Clk 54 WF480 / Gracis ,9 30,6 27,6 55 DAMATIC ,2 30,8 25,9 63 VESA Standard ,0 31,5 25,2 74 MAC Mode ,7 35,0 31,4 75 MAC Mode ,9 35,1 30,3 81 VESA Standard ,0 37,5 31,5 83 VESA Standard ,7 37,8 31,4 85 VESA Standard ,9 37,9 31,5 87 VESA Standard ,9 43,2 35,9 1 NEC 15kHz ,0 15,0 13,5 2 NEC 15kHz i ,0 15,0 13,5 65 Std.-VGA ,0 31,5 25,2 86 NEC 42.5kHz ,0 42,5 37,4 20 NTSC (halfline) ,9 15,7 12,9 23 NTSC ,9 15,7 12,9 25 NTSC Interlaced ,1 15,8 13,6 11 PAL Interlaced ,0 15,6 13,5 27 ABB DSAV ,1 17,9 15,6 29 Hercules Monochrom ,7 18,4 16,2 72 XGA ,8 39,4 35,5 163 VGA ,2 31,5 28,4 167 VGA ,9 37,8 35,4 31 Custom ,9 20,6 18,5 46 NEC 27kHz ,0 27,0 24,3 73 XGA ,8 39,4 35,5 165 VGA ,2 31,5 28,

47 Specifications Index Description Hres Vres V-Freq H-Freq Dot Clk 169 VGA ,0 37,9 35,5 41 VDU 2000 Coros ,1 25,4 24,5 43 Teleperm / DS ,0 25,7 23,1 66 NTSC Progressive ,0 31,5 27,0 71 XGA ,9 39,3 35,4 62 PC -Textmode ,2 31,5 28,4 21 MTBI ,9 15,7 14,1 68 GTF ,0 35,8 34,9 88 GTF ,9 43,2 42,9 91 GTF ,9 45,1 45,5 104 GTF ,0 51,4 51,8 89 NEC 44kHz ,2 44,0 44,0 58 CP 527/ ,0 30,9 32,8 76 VG ,2 35,1 35,9 84 VG ,2 37,8 39,9 92 VESA ,9 46,8 49,4 96 VS ,1 48,0 49,9 106 VESA Standard ,9 53,6 56,2 100 MAC Mode ,0 49,5 55,4 101 MAC Mode ,5 49,7 57,3 80 VESA Standard ,1 37,4 46, i ,0 35,5 44, p ,8 35,5 44,9 98 VG ,9 48,3 64,9 99 MAC Mode ,9 48,7 63,9 112 VS ,0 56,4 74,

48 Media / DVI Converter Index Description Hres Vres V-Freq H-Freq Dot Clk 113 IBM ,1 57,5 75,0 114 SUN Mode ,0 58,0 75,2 116 VESA Standard ,0 60,0 78,7 117 VESA Standard ,9 60,2 79,9 133 VESA Standard ,9 68,6 94,4 108 Custom Corus Group ,0 54,3 73,0 69 VESA Standard ,3 38,2 53,2 13 DISET oversample ,0 15,6 24,5 107 VESA Standard ,0 53,7 81,6 121 DMT ,0 63,5 100,1 122 VESA Standard ,0 63,8 94,4 130 VESA Standard ,0 67,5 108,0 146 GTF ,1 77,1 119,7 134 Apple Mac II ,1 68,7 100,0 118 SUN Mode ,0 61,8 94,4 119 SUN Mode ,7 62,5 95,5 137 NOKIA 447X ,0 71,7 105,5 14 GBE3977 Oversample ,0 15,6 26, i ,0 28,0 44,6 82 VESA CVT 16: ,0 37,5 74,3 90 VESA CVT 16: ,9 44,8 74,5 94 TV Mode ,0 47,7 80,1 97 TV Mode ,0 48,1 81,2 102 Beamer 16: ,8 49,7 83,5 115 VESA Standard ,0 60,0 108,0 139 GTF ,0 72,1 124,

49 Specifications Index Description Hres Vres V-Freq H-Freq Dot Clk 143 DMT 127A ,0 75,0 126,0 148 GTF ,3 77,5 133,9 156 VESA Standard ,0 85,9 148,4 105 TV Mode ,1 53,4 90,1 120 SONY GDM2036s ,9 63,3 108,1 124 VESA Standard ,9 63,9 107,9 125 Siemens SMI ,0 64,0 112,6 135 VESA Standard ,0 70,7 119,9 138 SUN Mode ,7 71,7 117,0 147 SXGA Unix ,0 77,2 130,9 149 HP Workstation B123L ,0 78,1 135,0 151 VESA Standard ,0 79,9 134,9 158 VESA Standard ,0 91,1 157,4 93 TV Mode 16: ,1 47,6 84,5 95 Plasma TV 16: ,0 47,7 85,5 127 NVIDIA 4: ,7 65,0 121,2 150 GTF ,0 78,8 149,4 153 GTF ,0 82,2 155,9 26 NTSC ,0 15,8 27,1 109 TV Mode 16: ,0 55,6 89, i ,0 50,0 108,0 110 TV Mode 16: ,9 55,8 118,7 123 VESA Standard ,2 63,8 136,8 142 VESA Standard ,0 75,0 162,0 144 UXGA ,1 75,0 138,0 145 UXGA rb ,3 75,4 140,

50 Media / DVI Converter Index Description Hres Vres V-Freq H-Freq Dot Clk 152 VESA Standard ,0 81,3 175,6 157 VESA Standard ,0 87,5 189,0 159 VESA Standard ,0 93,2 164,0 160 VESA Standard ,0 93,8 202,6 126 WSXGA+ 16: ,9 64,7 119,0 128 WSXGA ,1 65,4 146,5 154 WSXGA ,9 82,3 187,0 161 WSXGA ,0 93,9 214,8 155 VESA Standard ,0 83,6 204, i ,0 28,1 74, i@60Hz ,0 33,8 74, p ,7 55,9 147, p ,7 66,8 172, p ,0 67,5 148,5 140 WUXGA ,9 74,0 153,9 141 WUXGA ,6 74,2 192, *1080@60Hz ,0 67,5 148, *1152@60Hz ,9 71,0 156,

51 Pos: 38 /806-IHSE/Technische 2 Pos: 40 /806-IHSE/Technische Daten/Serielle Ausstattung/238-5v-xx_Serielle 1 Specifications Video modes for Component- / Composite-Video, S-Video and SDI Description CVBS S-Video Component (HD-)SDI 480i / 60Hz X X X X 576i / 50Hz X X X X 480p / 60Hz X 576p / 50Hz X 720p / 50Hz X X 1080p 1080i

52 Pos: 41 /806-IHSE/Technische 1 Media / DVI Converter 7.3 Serial Control Telegram Structure Command <STX>, <size>, <converter indication>, <ten s key>, <unit key>, <ETX> Response <ACK> Description Type Byte Hex-Value STX 1 0x02 Size 1 0x06 Converter indication 1 0x43 (corresponds to ASCII C ) Ten s key 1 0x30 0x33 Unit key 1 0x30 0x39 ETX 1 0x03 ACK 1 0x Examples The remote control consists of 32 keys with commands from: Key 1: <0x02>, <0x06>, <0x43>, <0x30>, <0x31>, <0x03> to Key 32: <0x02>, <0x06>, <0x43>, <0x33>, <0x32>, <0x03> Key 23 "DVI": <0x02>, <0x06>, <0x43>, <0x32>, <0x33>, <0x03>

53 Pos: 42 /806-IHSE/Technische Daten/Pinbelegungen/Buchse DVI-D @ 1 Pos: 43 /806-IHSE/Technische Daten/Pinbelegungen/Buchse DVI-I @ 1 Specifications 7.4 Connector Pinouts Connector DVI-D Single-Link Pin Signal Pin Signal Pin Signal 1 T.M.D.S data 2 9 T.M.D.S data 1 17 T.M.D.S data 0 2 T.M.D.S data T.M.D.S data T.M.D.S data T.M.D.S data 2 GND 11 T.M.D.S data 1 GND 4 n.c. 12 n.c. 20 n.c. 5 n.c. 13 n.c. 21 n.c. 6 DDC Input (SCL) 14 +5VDC high impedance 7 DDC Output (SDA) 8 Internal use 16 Hot Plug recognition 19 T.M.D.S data 0 GND 22 T.M.D.S clock GND 15 GND 23 T.M.D.S clock + 24 T.M.D.S clock C1 Internal use C3 Internal use C2 n.c. C5 GND C4 Internal use

54 Pos: 44 /806-IHSE/Technische Daten/Pinbelegungen/RCA @ 1 Pos: 45 /806-IHSE/Technische Daten/Pinbelegungen/BNC (SDI, @ 1 Media / DVI Converter Connector DVI-I Single-Link Pin Signal Pin Signal Pin Signal 1 T.M.D.S data 2 9 T.M.D.S data 1 17 T.M.D.S data 0 2 T.M.D.S data T.M.D.S data T.M.D.S data 0+ 3 T.M.D.S data 2 GND 11 T.M.D.S data 1 GND 4 n.c. 12 n.c. 20 n.c. 5 n.c. 13 n.c. 21 n.c. 6 DDC Input (SCL) 14 +5VDC high impedance 7 DDC Output (SDA) 8 V-sync 16 Hot Plug recognition 19 T.M.D.S data 0 GND 22 T.M.D.S clock GND 15 GND 23 T.M.D.S clock+ 24 T.M.D.S clock C1 Red signal C3 Blue signal C2 Green signal C5 GND C4 H-sync RCA (Cinch) Picture Pin Signal 1 GND 2 Data IN / OUT

55 Pos: 46 /806-IHSE/Technische Daten/Pinbelegungen/Mini-DIN @ 1 Pos: 47 /806-IHSE/Technische Daten/Pinbelegungen/D-Sub 9 @ 1 Pos: 48 /806-IHSE/Technische Daten/Pinbelegungen/Buchse Mini-USB Typ @ 1 Specifications BNC (SDI, RGB) Picture Pin Signal 1 Data IN 2 GND Mini-DIN (S-Video) Picture Pin Signal 1 GND (Y) 2 GND (C) 3 Luminance (Y) 4 Chrominance (C) D-Sub 9 (EGA) Picture Pin EGA CGA MDA 1 GND GND GND 2 Red (LSB) 3 Red (MSB) Red 4 Green (MSB) Green 5 Blue (MSB) Blue 6 Green (LSB) Intensity Intensity 7 Blue (LSB) Video 8 H-SYNC H-SYNC H-SYNC 9 V-SYNC V-SYNC V-SYNC

56 Pos: 49 /806-IHSE/Technische @ 1 Pos: 52 /806-IHSE/Technische 1 Media / DVI Converter Connector Mini USB Type B Picture Pin Signal Color 1 VCC (+5VDC) Red 2 Data White 3 Data + Green 4 n.c. 5 GND Black Power Supply Picture Pin Signal Inside VCC (+5VDC) Outside GND Pos: 50 /806-IHSE/Technische Power Supply Voltage 5VDC Power Requirement K238-5V: max. 900 ma K238-5VE / -5VS / -5FBNC: max. 1,100 ma Pos: 51 /806-IHSE/Technische Environmental Conditions Operating Temperature Storage Temperature Relative Humidity 41 to 113 F (5 to 45 C) 13 to 140 F ( 25 to 60 C) Max. 80% non-condensing

57 Pos: 54 /806-IHSE/Hilfe im Problemfall/UEB_Hilfe im 1 Specifications 7.7 Size K238-5V Media / DVI Converter 103 x 143 x 29 mm (4" x 5.6" x 1.1") Shipping Box 210 x 140 x 165 mm (8.3" x 5.5" x 6.5") K238-5VE / -5VS / -5FBNC Media / DVI Converter 103 x 143 x 43 mm (4" x 5.6" x 1.7") Shipping Box 460 x 250 x 120 mm (18.1" x 9.8" x 4.7") Pos: 53 /806-IHSE/Technische Daten/Transportgewicht Shipping Weight K238-5V Media / DVI Converter Shipping Box 0.3 kg (0.7 lb) 1.8 kg (4.0 lb) K238-5VE / -5VS / -5FBNC Media / DVI Converter Shipping Box 0.4 kg (0.9 lb) 2.3 kg (5.1 lb)

58 Pos: 56 /806-IHSE/Hilfe im 1 Media / DVI Converter 8 Troubleshooting Pos: 55 /806-IHSE/Hilfe im Blank Screen Diagnosis Possible Reason Measure Status LED blue Status LED green Status LED dark red Status-LED violet No video signal detected No monitor detected No monitor detected Resolution of source device not supported Resolution of source device not supported Check connections. Check input selection in the OSD (source type). Load DDC information of the connected monitor (see Chapter 6.2, Page 39). Reboot CPU if necessary. Check connection, length and quality of the DVI-D cable to monitor, tighten cable thumbscrews. Check connection, length and quality of the DVI-D cable to monitor, tighten cable thumbscrews. Fill in the video mode questionnaire (Download), so that a customer specific video mode can be made. Fill in the video mode questionnaire (Download), so that a customer specific video mode can be made