PT-AE4000 S P E C F I L E. Full High-Definition Home Cinema Projector

Transcription

1 Product Number : Product Name : PT-E4000 s of September ppearance and specifications are subject to change without notice. < >

2 PT-E4000 Specifications Main Unit Power supply Power consumption LCD* 2 panel Panel size Display method Drive method Pixels Lamp* Lens Screen size Throw distance Colors Brightness* 4 Center-to-corner uniformity ratio* Contrast* 4 Resolution Scanning frequency RGB YPBPR (YCBCR) S-Video/Video Optical axis shift* Keystone correction range Installation OSD languages Terminals HDMI IN COMPUTER (RGB) IN RGB signal YPBPR signal V C, 50/0 Hz 240 W (0.08 W* in standby mode with fan stopped) 0.74 diagonal (:9 aspect ratio) Transparent LCD panel (x, R/G/B) ctive matrix 2,07,00 (,920 x,080) x, total of,220,800 pixels 70 W UHM lamp Powered zoom/focus lens (::2), F.9.2, f mm inches.28.0 m ( 9 59 ) (:9 aspect ratio) Full colour (,07,74,824 colors),00 lumens* 5 85 % 00,000:* 5 (full on/full off),920 x,080 pixels fh 070 khz, fv Hz, Dot clock: Less than 50 MHz 480i (525i): fh 5.75 khz; fv 0 Hz, 57i (25i): fh 5. khz; fv 50 Hz, 480p (525p): fh.5 khz; fv 0 Hz, 57p (25p): fh.25 khz; fv 50 Hz, 720/50p (750/50p): fh 7.5 khz; fv 50 Hz, 720/0p (750/0p): fh 45 khz; fv 0 Hz, 080/50i (25/50i): fh khz; fv 50 Hz, 080/0i (25/0i): fh.75 khz; fv 0 Hz, 080/24p (25/24p): fh 27 khz; fv 24 Hz, 080/50p (25/50p): fh 5. khz; fv 50 Hz, 080/0p (25/0p): fh 7.5 khz; fv 0 Hz fh 5.75 khz fv 0 Hz (NTSC, NTSC4.4, PL-M, PL0) fh 5. khz fv 50 Hz (PL, PL-N, SECM) Horizontal: ±40%, vertical: ±00% Vertical: approx. ±0 Ceiling/floor, front/rear (menu selection) English, French, German, Spanish, Italian, Chinese, Korean, Russian, Swedish, Danish, Norwegian, Polish, Czech, Hungarian, Portuguese, Thai, Japanese HDMI connector x, HDMI (Deep Color, x.v.color * 7, CEC* 8 ), HDCP compliant, supports HDVI Control Version 4 D-sub HD 5-pin (female) x R, G, B: 0.7 V [p-p] (.0 Vp-p for Sync on G), 75 ohms HD/SY, VD: TTL (positive/negative polarity compatible) Y:.0 V [p-p] (including sync signal), 75 ohms, PB, PR: 0.7 V [p-p], 75 ohms s of September 2009 < 2 >

3 PT-E4000 Power cord length Cabinet material Dimensions (W x H x D) Weight* 0 Operating temperature Operating humidity COMPONENT IN Y PB/CB, PR/CR TRIGGER IN/OUT VIDEO IN S-VIDEO IN SERIL IN RC pin (Y, PB/CB, PR/CR) x.0 [p-p], 75 ohms 0.7 V [p-p], 75 ohms M x 2, 2 V, max. 00 m (input/output selectable using on-screen menu) RC pin x,.0 V [p-p], 75 ohms Mini DIN 4-pin x, Y:.0 Vp-p, C: 0.28 V [p-p], 75 ohms D-sub 9-pin (RS-22C) x, for external control m (9 0 ) Molded (+BS) 40 x 0 x 00 mm (8-/2 x 5-/2 x -25/2 )* 9 pprox. 7. kg (.09 lbs.) 0 40 C (2 04 F) 20%80% (no condensation) Remote Control Unit Power supply Operation range* Dimensions (W x H x D) Weight V DC (R/LR/ type battery x 2) pprox. 7 m when operated from directly in front of the signal receptor 48 x 8 x 28.5 mm (-7/8 x 5-7/ x -/8 ) 25 g (4.4 oz.) Supplied ccessories Power cord Wireless remote control unit Batteries for remote control (R/LR/ type x 2) Optional ccessories Replacement lamp: ET-LE4000 Ceiling mount bracket for high ceilings: ET-PKE2000 Ceiling mount bracket for low ceilings: ET-PKE000S Cable cover: ET-E2000 *: Up to 220 V. *2: The projector uses a type of liquid crystal panel that typically consists of millions of pixels. This panel is built with very high-precision technology to provide the finest possible image. Occasionally, a few pixels may remain turned on (bright) or turned off (dark). Please note that this is an intrinsic characteristic of the manufacturing technology that affects all products using LCD technology. *: The projector uses a high-voltage mercury lamp that contains high internal pressure. This lamp may break, emitting a large sound, or fail to illuminate, due to impact or extended use. The length of time that it takes for the lamp to break or fail to illuminate varies greatly depending on individual lamp characteristics and usage conditions. *4: Measurement, measuring conditions, and method of notation all comply with ISO 28 international standards. *5: In dynamic mode, with dynamic iris on. *: Shift range is limited during simultaneous horizontal and vertical shifting. *7: Effective in Color image mode. *8: CEC is an abbreviation for Consumer Electronics Control. Operation may not be possible with some connected equipment or settings. *9: Lens and legs not included. *0: verage value. May differ depending on models. *: Operation range differs depending on environments. Weights and dimensions shown are approximate. Specifications are subject to change without notice. This product may be subject to export control regulations. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. x.v.color is a trademark of Sony Corporation. ll other trademarks are the property of their respective trademark owners. s of September 2009 < >

4 PT-E4000 Dimensions 00 (-2/2) unit : mm (inch) NOTE: This illustration is not drawn to scale. 5 (9/) 0 (2-5/) 47 (5-25/2) (4-9/) 0 (5-/8) 20 (9-/2) 7 (2/2) 40 (8-/2) Terminals HDMI input 2 HDMI 2 input HDMI input 4 Computer input 5 Component (YPBPR/YCBCR) input S-Video input 7 Video input 8 Trigger input/output 9 Trigger 2 input/output 0 Serial input COMPUTER IN connector pin assignment 5 no. signal no. signal no. signal R, PR/CR 2 G, Y 7 2 B, PR/CR 8 HD/SY 5 0 D-sub HD 5-pin, female VD s of September 2009 < 4 >

5 Full High Definition Home Cinema Projector PT-E4000 Standard setting-up positions Upper edge of projected image unit : mm (inch) H L 50 (5-29/2 ) Projected image 8 (7-/8 ) NOTE: H L * Illustrations show the projector installed using optional ceiling bracket ET-PKE000S. Lower edge of projected image This illustration is not drawn to scale. Values shown are approximate. W 70 (2-/4 ) 5 (2-9/ ) L Projected image Projection distance for screen aspect ratio of :9 Projection size (:9) Diagonal length Projection distance (L) Min (Wide) Max (Telephoto) Height from the edge of screen to center of lens (H) Width from the right edge of screen to center of lens (W).02 m / m / m / 0.78 m / m / m / m / m / 20.8 m / m / m / m / 00.2 m /.5 m / m / m / m / m / m / 9 0. m / m / m / m / m / m / m / m / 8 4. m / m / m / m / m / m / m / m / m / m 0.75 m / m 0.9 m / m.2 m / m. m / m.49 m / m.8 m / m.87 m / m 2.24 m / m 2.80 m / m.74 m / m 4.7 m / m 5.0 m / m 0.80 m / 0. m 0.99 m / m.20 m / 0.5 m.9 m / 0.8 m.59 m / m.79 m / m.99 m / m 2.9 m / m 2.99 m / 0.44 m.98 m / m 4.98 m / m 5.98 m / Projection distance for screen aspect ratio of 2.5: (When projecting both 2.5: and :9 images onto a 2.5: screen using the Lens Memory function.) Projection size (2.5:) Diagonal length.02 m / m / m / 0.78 m / m / m / m / m / 20.8 m / m / m / m / 00 Projection distance (L) Min (Wide). m / 4. m / m / m / 7 2. m / m / m / m / m / m / m / 2 9. m / 4 Max (Telephoto) / 2. m / m / 9. m / m / m / m / m / m / m / m / m / 47 Height from the edge of screen to center of lens (H) 0.00 m 0.40 m / m 0.49 m / m 0.0 m / m 0.9 m / m 0.80 m / m 0.90 m / m 0.99 m / m.9 m / m.49 m / m.99 m / m 2.49 m / m 2.98 m / Width from the right edge of screen to center of lens (W) 0.07 m 0.4 m / m 0.80 m / m 0.9 m / m. m / m.27 m / m.4 m / m.59 m / m.9 m / m 2.9 m / m.8 m / m.98 m / 0.5 m 4.77 m / NOTE: The values of L shown above vary due to characteristics of the zoom lens. Images may slightly distort due to characteristics of the zoom lens when the zoom lens is set to the minimum throw distance. Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. :9 minimum L (m) = (diagonal screen size in inches) x maximum L (m) = (diagonal screen size in inches) x : (When projecting both 2.5: and :9 images onto a 2.5: screen using the Lens Memory function.) minimum L (m) = (diagonal screen size in inches) x maximum L (m) = (diagonal screen size in inches) x NOTE: The accuracy of calculated value by the formula shown above is ±5%. s of September 2009 < 5 >

6 PT-E4000 Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image) 0.4H 0.4H V (Height of projected image).0v.0v Standard position of projected image Installable angle Install the projector at an angle within the range shown below. Vertical direction The projector may be installed at a vertical angle of ± Horizontal direction The projector may be installed at a vertical angle of ± s of September 2009 < >

7 PT-E4000 Computer data compatibility This projector accepts up to 70 khz horizontal scanning frequency and 50 MHz dot clock. NOTE: The display resolution of this projector is 920 x 080 pixels. If the display resolution indicated in the above data does not match this resolution, the input signal will be converted to 920 x 080 pixels. List of Compatible Signals Display mode Display resolution (dots) Scanning frequency Dot clock H (khz) V (khz) frequency (MHz) Picture 2 quality Format NTSC/NTSC4.4/PL-M/PL0 720 x 480i PL/PL-N/SECM 720 x 57i 480i (525i) 720 x 480i 57i (25i) 720 x 57i 480p (525p) 720 x 48 57p (25p) 720 x (750)/0p,280 x (750)/50p,280 x (25)/0i,920 x,080i 080 (25)/50i,920 x,080i 080 (25)/24p,920 x, (25)/0p,920 x, (25)/50p,920 x,080 VG x x x x 480 WIDE x 480 SVG 800 x x x x x 00 WIDE00,072 x 00 WIDE720,280 x 720 XG,024 x 78,024 x 78,024 x 78,024 x 78,024 x 78 WIDE78,280 x 78 MXG,52 x 84,52 x 84 SXG,280 x,024 WIDE78-2,0 x 78 SXG0+,400 x,050 WIDE800,280 x 800 WIDE900,440 x 900 WIDE 080/0,920 x,080 WIDE 080/50,920 x, The i appearing after the resolution indicates an interlaced signal. 2. The following symbols are used to indicate picture quality. Maximum picture quality can be obtained. Signals are converted by the image processing circuit before picture is projected. VIDEO/S-VIDEO VIDEO/S-VIDEO COMPONENT COMPONENT COMPONENT/HDMI COMPONENT/HDMI COMPONENT/HDMI COMPONENT/HDMI COMPONENT//HDMI COMPONENT//HDMI COMPONENT/HDMI COMPONENT//HDMI COMPONENT//HDMI /HDMI s of September 2009 < 7 >

8 PT-E4000 Serial connector The serial connector complies with RS-22C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. Signal name Description No. Signal name Description 2 TXD Send data 7 RTS Connected internally RXD Receive data 8 CTS Connected internally 4 9 D-sub 9-pin 5 Ground Communication conditions (factory setting) Signal level Synchronization method Baud rate Parity Character length Stop bit X parameter S parameter RS-22C-compliant Start-stop synchronization 9,00 bps None 8 bits bit None None Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. dd parameters according to the details of control. STX C C2 C : P P2 P P4 ETX Start ( byte) Colon ( byte) Parameter (-4 bytes) Command ( bytes) (Control and/or query commands) End ( byte) CUTIION When sending multiple commands, be sure to send the next command after receiving a response from the projector. Cable specifications Projector (DTE) DSR s of September 2009 < 8 >

9 PT-E4000 Control commands Command PON POF IIS OMN OEN OBK OCU OCD OCL OCR OLE OST OFZ FC OSH 2 OVM OWM VS VPM OOT OMM DP DCM OVL OSM Function Power on (standby mode on) Power off (standby mode off) Input signal selection Menu Enter Return Cursor up Cursor down Cursor left Cursor right The same function as LENS button Default Freeze The same function as FUTION button Blank on/off Picture mode switch Waveform monitor activate/off spect switch Picture mode Off timer The same function as MEMORY LOD button The same function as PICTURE DJUSTMENT button Color management menu The same function as VIER Link button The same function as SUB MENU button Parameter CP, SVD, VID, HD, HD2, HD, RG 0, 0,, 2,, 4, 5,, 7, 8 NOR, DYN, CL, CL2, CN, CN2, CN 0,, 2,, 4, 5,, 7 Option Menu Command VXX Lens memory Gamma output level (Y) Gamma output level (R) Gamma output level (G) Gamma output level (B) Gamma input level Trigger output Trigger 2 output LMLI0= LMLI0= GOS0=00000 GOS0= GOS=00000 GOS= GOS2=00000 GOS2= GOS=00000 GOS= GIS0=0000 GOS0=0900 TROI0= TROI0=+0000 TROI= TROI=+0000 PON is the only command that is effective in standby mode; all other commands are invalid. The PON command is not accepted during lamp on control. fter the lamp has been turned off and while the cooling fan is still operating, lamp on control will not be activated for about 85 seconds in order to protect the lamp. 2 Do not send OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. Control command parameters Command Size (Byte) Parameter IIS OFZ OWM VPM OOT QVX:LMLI0 GOS0 GOS GOS2 GOS GIS0 TROI0 TROI 5 CP = component, SVD = S-video, VID = video, HD = HDMI, HD2 = HDMI2, HD = HDMI, RG = computer 0 = off, = on 0 = off, = full scan (Y), 2 = full scan (R), = full scan (G), 4 = full scan (B), 5 = single line (Y), = single line (R), 7 = single line (G), 8 = single line (B) NOR = normal, DYN = dynamic, CL = color, CL2 = color 2, CN = cinema, CN2 = cinema 2, CN = cinema 4 = 50 min, 5 = 80 min, = 20 min, 7 = 240 min LMLI0= = lens memory, LMLI0= = lens memory 2, LMLI0= = lens memory, LMLI0= = lens memory 4, LMLI0= = lens memory 5, LMLI0= = lens memory GOS0=pp2dd2dd4 pp2 = point number: 0 09, dd2dd4 = output: GOS=pp2dd2dd4 pp2 = point number: 0 09, dd2dd4 = output: GOS2=pp2dd2dd4 pp2 = point number: 0 09, dd2dd4 = output: GOS=pp2dd2dd4 pp2 = point number: 0 09, dd2dd4 = output: GIS0=pp2dd2d pp2 = point number: 0 09, dd2d = output: TROI0= = low, TROI0= = high TROI= = low, TROI= = high s of September 2009 < 9 >

10 PT-E4000 Status asking commands Command QPW QIN QPM QSH QFZ QOT QWM Description Standby power status Input signal status Picture mode status Blank function status Freeze function status Off timer status Waveform monitor statusutton Parameter 000 = off, 00 = on CP = component, SVD = S-video, VID = video, HD = HDMI, HD2 = HDMI2, HD = HDMI, RG = computer NOR = normal, DYN = dynamic, CL = color, CL2 = color 2, CN = cinema, CN2 = cinema 2, CN = cinema 0 = off, = on 0 = off, = on 0 = off, = 0 min, 2 = 90 min, = 20 min, 4 = 50 min, 5 = 80 min, = 20 min, 7 = 240 min 0 = off, = full scan (Y), 2 = full scan (R), = full scan (G), 4 = full scan (B), 5 = single line (Y), = single line (R), 7 = single line (G), 8 = single line (B) Option Menu Command QVX Gamma output level (Y) Gamma output level (R) Gamma output level (G) Gamma output level (B) Gamma input level GOS0=pp2dd2dd4 pp2 = point number: 0 09 dd2dd4 = output: GOS=pp2dd2dd4 pp2 = point number: 0 09 dd2dd4 = output: GOS2=pp2dd2dd4 pp2 = point number: 0 09 dd2dd4 = output: GOS=pp2dd2dd4 pp2 = point number: 0 09 dd2dd4 = output: GIS0=pp2dd2d pp2 = point number: 0 09 dd2d = output: NOTE: If a wrong command is received, the projector will send an ER40 command to the computer. Command example To set the volume to +0, send the command as shown below. STX VL : 0 ETX Start Command Parameter End NOTE: When sending commands without parameters, a colon (:) is not necessary. s of September 2009 < 0 >

11 PT-E4000 Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions.. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 00 mm (-5/ ) or more around the projector s air intake openings.. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0 C/2 F and 5 C/95 F. lso make sure the projector s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings. 00 mm (-5/ ) or more 00 mm (-5/ ) or more 00 mm (-5/ ) or more Direction of air intake and exhaust Intake Exhaust Operating the projector continuously. If the projector is to be operated continuously 0 hours or more, lamp replacement cycle duration becomes shorter. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. s of September 2009 < >