1 05/06/06. MX2500/3500, White, Blue, LX65/100/120, L6, L8, LU77 and LW40. This Section Includes: 1.1 Overview page 1. Control Commands..
|
|
- Lynette Pierce
- 5 years ago
- Views:
Transcription
1 1 05/06/06 Section 1 MX2500/3500, White, Blue, LX65/100/120, L6, L8, LU77 and LW40 Serial Communications NOTE: There is no connect/disconnect command. The built-in keypad, IR remote and RS-232 control will function simultaneously. This Section Includes: 1.1 Overview page Connection.page Messages:...page 3 Control Commands.. page 3 Status Commands...page Controlling Multiple Projectors:....page Overview Matrix 2500/3500, White, Blue, LX65/100/120, L6, L8, LU77 & LW40 serial communication allows the control of projectors by an external controller, such as an AMX or Creston controller. Once connected to the RS-232 port of the projector, controllers can access projector controls and setups, issue commands and receive replies. NOTE: The White, Blue, L6-01,02 & -03 series and L8-01 series must have Version 3.0 main software or higher in them to work with the extended communications as outlined in this document. 1.2 Connection To use Matrix 2500/3500, White, Blue, LX65/100/120, L6, L8, LU77 and LW40 serial communications you must first connect the projector to a PC or controller. Using an RS232 Null Modem cable, connect the projector to the computer. Refer to Table 1 for Port Characteristics. Refer to Table 2 for projector wiring hook-up.
2 2 05/06/06 White, Blue, Lx 65, Lx 100, LX120, L6, L8, MX2500, MX3500 and LW40 Protocol: RS232C Baud Rate: bps Data Bits: 8 bits Stop Bit: 1 bit Parity : None Flow Cntrl: None Table 1: Port Characteristics NOTE: 1) To avoid damage, connect only properly wired RS-232 serial communication cables to the projector Serial Port. 2) Communication cables longer than 50 feet should be of high quality and low capacitance, well shielded and grounded. Table 2: Projector Wiring Hook-Up
3 3 05/06/ Messages The White, Blue, LX65/100/120, L6, L8, MX2500, MX3500, LU77 and LW40 have two types of commands: Control Command and Status Request Commands. Each command must be succeeded with a "CR" code, which is the equivalent to a carriage return. In hexadecimal the "CR" code is 0D. Note: All communications (commands and replies) are hexadecimal. Ensure you are sending hexadecimal. Commands are case sensitive. Make sure to always send letters in upper case. The following delays are recommended: 10ms delay between characters. 100ms delay between commands. 300, 3000 or 5000ms delay between commands for the following: Check Table 3 Control Commands Control commands are used to set or modify various projector characteristics or to emulate key presses from the built in keypad/ir remote control. Note: Unless Display is set to OFF in the Setting Menu, most commands will cause an OSD to appear. Control commands follow the protocol: Cxx(CR) Where XX is the command code (see Table 3 for a complete list of command codes) and (CR) is 0D. Note: Commands are listed in ASCII, but all communications (commands and replies) are hexadecimal. Ensure you are sending hexadecimal. Commands are case sensitive. Make sure to always send letters in upper case. Example: As listed, Power On = C 0 0 (CR) You should send: 43h 30h 30h 0Dh When a control command is sent to the projector, a response is sent back to the controller to notify it about how the command was treated. There are two possible responses to a control command: 06 (CR) -- Command accepted and executed? (CR) -- Command not recognized
4 4 05/06/06 Table 3: Command Codes Command Function Code 00 POWER ON 5000ms between commands Notes 01 (quick) POWER OFF 3000ms between commands 05 INPUT ms between commands 06 INPUT ms between commands 07 INPUT ms between commands 08 INPUT ms between commands Only works with projectors that have 4 inputs. 09 VOLUME + Increments the Volume setting by one. 0A VOLUME - Decrements the Volume setting by one. 0B 0C AUDIO MUTE ON AUDIO MUTE OFF 0D NO SHOW ON Video Mute ON 0E NO SHOW OFF Video Mute OFF 0F AV NORMAL SIZE 10 AV WIDE SIZE Sets AV source to be displayed in 4:3 aspect ratio. 300ms between commands Sets AV source to be displayed in Anamorphic aspect ratio. 300ms between commands 1C MENU ON Brings main menu up on screen 1D MENU OFF Clears main menu from screen 1E CLEAR SCREEN Clears OSD regardless of location in software. 27 IMAGE KEY 30 DIGITAL ZOOM + 31 DIGITAL ZOOM - 3A RIGHT ARROW KEY First issuing of command accesses the Digital Zoom function. Each additional issuing increments Digital Zoom by one. First issuing of command accesses the Digital Zoom function. Each additional issuing decrements Digital Zoom by one. 3B 3C 3D 3F LEFT ARROW KEY UP ARROW KEY DOWN ARROW KEY SELECT KEY 43 FREEZE ON 44 FREEZE OFF 46 ZOOM LENS DOWN KEY 47 ZOOM LENS UP KEY
5 5 05/06/06 4A FOCUS DOWN KEY 4B FOCUS UP KEY 5D LENS SHIFT UP 5E LENS SHIFT DOWN 5F LENS SHIFT LEFT 60 LENS SHIFT RIGHT 70 FULL LAMP MODE 71 HALF LAMP MODE 1 72 HALF LAMP MODE 2 White, L8, LX100, LU77 and MX3500 White, L8, LX100, LU77 and MX Lamp Mode (White,L8, LX100, LU77, MX3500) 2 Lamp Mode (Blue, L6, LX65, MX2500 and LW40) 2 Lamp Mode Lamp 1 & 4 (White, L8, LX100, LU77 & MX3500) 1 Lamp Mode Lamp 1 (Blue, L6, LX65, MX2500 & LW40) When changing from Half Mode 1 to Half Mode 2 (and vice versa) the projector will go to Full Mode for 30 seconds for the transition. 2 Lamp Mode Lamp 2 & 3 (White, L8, LX100, LU77 & MX3500) 1 Lamp Mode Lamp 2 (Blue, L6, LX65, MX2500 & LW40) When changing from Half Mode 2 to Half Mode 1 (and vice versa) the projector will go to Full Mode for 30 seconds for the transition. 89 Auto Image 8A PRESENTATION TIMER 8E KEYSTONE + 8F KEYSTONE - First issuing of the command starts the Presentation Timer. Second issuing of the command stops the Presentation Timer. Third issuing of the command clears/resets the Presentation Timer. First issuing of command accesses the Electronic Keystone function. Each additional issuing increments Electronic Keystone by one. Additional issuings must occur within 3 seconds of one another. First issuing of command accesses the Electronic Keystone function. Each additional issuing increments Electronic Keystone by one. Additional issuings must occur within 3 seconds of one another. Extended Control Commands Control commands are used to set or modify various projector characteristics or to emulate key presses from the built in keypad/ir remote control. Note: Unless Display is set to OFF in the Setting Menu, most commands will cause an OSD to appear. Control commands follow the protocol: CF_ xx_## (CR) Where _ is a space, XX is the command code and ## is the parameter (see Table 3a for a complete list of extended control codes) and (CR) is 0D.
6 6 05/06/06 When a control command is sent to the projector, a response is sent back to the controller to notify it about how the command was treated. There are two possible responses to a control command: 06 (CR) -- Command accepted and executed? (CR) -- Command not recognized Table 3a: Extended Control Codes Command Function Code Timing Msec FSYNC Change fine sync 600 UP, DN Parameters TDOTS Change total dots 600 UP, DN CLAMP Change clamp value 600 UP, DN H-POS Change horizontal position 600 UP, DN V-POS Change vertical position 600 UP, DN IMAGE Select image mode 2000 INPUT Select input SCREEN Select screen size SYSTEM Select system 1000 TRUE Select screen size true 800 ON / OFF DZCENT Cancel digital zoom 500 CENT INPUT1 Select both input 1 and the signal 5000 INPUT2 Select both input 2 and the signal 5000 INPUT3 INPUT4 Select both input 3 and the signal 5000 Select both input 4and the signal 5000 BBACK Select blue background 500 ON, OFF IMAGEADJ Reset an image adj. Save an image adj Standard - STAND Real - REAL Cinema - CINEMA Image1 - CUSTOM1 or IMAGE1 Image2 - CUSTOM2 or IMAGE2 Image3 - CUSTOM3 or IMAGE3 Image4 - CUSTOM4 or IMAGE4 CUSTOM# for Network Communications IMAGE# for Serial Communications NORMAL, WIDE, TRUE, DZOOM UP, DZOOM DN AUTO, NTSC, NTSC443, PAL, SECAM, PAL-M, PAL-N, 1080I60, 1080I50, 1035I, 720P, 575P, 480P, 575I, 480I, MODE1~MODE5 S-VIDEO, HD-SDI S-VIDEO, HD-SDI S-VIDEO, HD-SDI S-VIDEO, HD-SDI Reset RST Save as Image 1 STR1 Save as Image 2 STR2 Save as Image 3 STR3
7 7 05/06/06 AVSERV Return an initial setting for such as horizontal resolution or vertical resolution in the AV mode 600 RST AVDDOTS Change Hor. resolution for AV 600 UP / DN AVDLINE Change Vertical resolution for AV 600 UP / DN AVHPOS Change Hor. Position for AV 600 UP / DN AVVPOS Change Vertical position for AV 600 UP / DN Save as Image 4 STR4 BRIGHT Control Brightness , UP / DN CONT Control Contrast , UP / DN COLOR Control Color , UP / DN TINT Control Tint , UP / DN SHARP Control Sharpness , UP / DN GAMMA Control Gamma , UP / DN VOLUME Control Volume , UP / DN MUTE Control Mute ON, OFF FLSCREN Control Full Screen ON, OFF PCSTORE Store to Mode# MODE1 ~ MODE5 DENHCR Control Digital Enhancement , UP / DN COLTEMP Set Color Temp WBAL-R Control White Balance Red , UP / DN WBAL-G Control White Balance Green , UP / DN WBAL-B Control White Balance Blue , UP / DN BASS Control Base , UP / DN TREBLE Control Base , UP / DN BLTINSP Turn Built in Speaker on and off ON, OFF English ENG German DEU French FRA Spanish ESP Italian ITA LANG Select Languages Portuguese POR Dutch NED Swedish SVE Japanese JPN Korean KOR Chinese CHI SOURCE Select Source S-VIDEO, HD-SDI
8 8 05/06/06 ON-STA Select ON Start setting ON, OFF P-MANE Select power management setting ON, OFF KEYSTONE Control Keystone UP, FUP, DN, FDN & RST DISP Select Display ON, OFF LOGO Select Logo ON, OFF CEIL Select Ceiling ON, OFF REAR Select Rear ON, OFF RCODE Select Remote Control Code Code1 001, Code2 002 LAMPH Reset Lamp Time RSTn - Reset each total lamp running time individually (n=1-3, 1=lamp No.1, 2=lamp No.2 ) LAMPMODE Select Lamp Mode FULL, HALF NZRED Select Noise Reduction ON, OFF PROGV Select Progressive Video ON, OFF FANSPEED Select Fan Speed Control Maximum MAX Normal NOR Status Request Commands Status request commands are used to poll the projector for the setting or mode of various projector characteristics. Status request commands follow the protocol: CRx(CR) Where X is the status item code (See Table 4 for a complete list of status item codes and descriptions) and (CR) is 0D. Table 4: Function Codes Command Function Code 0 Status Read See Table 4.0 Notes 1 Input Mode Read See Table Lamp Time Read See Table Setting Read See Table 4.4
9 9 05/06/06 5 Model Lists OEM s Manufacturer Model # 6 Temp Read See Table Lamp Mode Read See Table PC Type Read See Table 4.9 A Mute Status Read See Table 4.A Table Status Read ss(cr) ss: Meaning 00 POWER ON. 80 STANDBY 40 Projector just powered up and is currently in 30 sec. countdown 20 Projector just shut off and is in cooling down. 04 Lamps are off due to Power Management. 10 Power failure. 28 Temperature warning and cooling down. 08 Temperature warning and power is ON. 88 Temperature warning occurred and system has recovered. 02 No key input. 24 Lamp is OFF and Temperature warning by Power Management 21 Lamp off & Cooling Down 81 Standby after lamp off & cooling down Table Input Mode Read s(cr) s: Meaning 1 Input 1 is currently selected and being displayed. 2 Input 2 is currently selected and being displayed. 3 Input 3 is currently selected and being displayed. 4 Input 4 is currently selected and being displayed. Table Lamp Timer Read ssss (CR)
10 10 05/06/06 ssss: Meaning #### Each four-digit number represents the total hours that a lamp has been ON. The VIVID Blue, LX65 and RoadRunner L6 will respond with two four digit numbers one per lamp: Lamp1 Lamp 2 (CR). The VIVID White, LX100 and RoadRunner L8 will respond with four, four digit numbers one per lamp: Lamp1 Lamp2 Lamp3 Lamp4 (CR). Table Setting Read s(cr) ss: Meaning 11 Configured for Front Screen Floor Mount 10 Configured for Rear Screen Ceiling Mount. 01 Configured for Rear Screen Floor Mount 00 Configured for Front Screen Ceiling Mount Table Temperature Read _ss.s_ss.s_(cr) Note: _: space ss.s: Meaning Numbers First temperature reading is the sensor near the panel. The second reading is near the lamp. Units are Celsius. This item is used for service purposes. Ex. _ _ means a temperature of 31.5 o C and 35.2 o C -05.5_-01.2_ means a temperature of 5.5 o C and 1.2 o C E00.0 Error reading temperature Table Lamp Mode Read sscr) ss: Meaning for VIVID Blue L6, LX65 and MX Full Lamp Mode: All OFF 01 Full Lamp Mode: No. 1 ON, No. 2 OFF 02 Full Lamp Mode: No. 2 ON, No. 1 OFF
11 11 05/06/06 0F Full Lamp Mode: All ON 10 Half Lamp Mode 1: All OFF 11 Half Lamp Mode 1: No. 1 ON, No. 2 OFF 20 Half Lamp Mode 2: All OFF 22 Half Lamp Mode 2: No. 2 ON, No. 1 OFF NOTE: If you receive a response that is not found in these tables then the projector is in transition of lamp modes. Resend the command in one (1) minute. ss: Meaning for VIVID White L8, LX100, LU77 and MX Full Lamp Mode: All OFF 01 Full Lamp Mode: No. 1 ON, No. 2, 3, 4 OFF 02 Full Lamp Mode: No. 2 ON, No. 1, 3, 4 OFF 03 Full Lamp Mode: No. 1, 2 ON, No. 3, 4 OFF 04 Full Lamp Mode: No. 3 ON, No. 1, 2, 4 OFF 05 Full Lamp Mode: No. 1, 3 ON, No. 2, 4 OFF 06 Full Lamp Mode: No. 2, 3 ON, No. 1, 4 OFF 07 Full Lamp Mode: No. 1, 2, 3 ON, No. 4 OFF 08 Full Lamp Mode: No. 4 ON, No. 1, 2, 3 OFF 09 Full Lamp Mode: No. 1, 4 ON, No. 2, 3 OFF 0A Full Lamp Mode: No. 2, 4 ON, No. 1, 3 OFF 0C Full Lamp Mode: No. 3, 4 ON, No. 1, 2 OFF 0D Full Lamp Mode: No. 1, 3, 4 ON, No. 2 OFF 0E Full Lamp Mode: No. 2, 3, 4 ON, No. 1 OFF 0F Full Lamp Mode: All ON 10 Half Lamp Mode 1: All OFF 11 Half Lamp Mode 1: No. 1 ON, No. 2, 3, 4 OFF 18 Half Lamp Mode 1: No. 4 ON, No. 1, 2, 3 OFF 19 Half Lamp Mode 1: No. 1, 4 ON, No. 2, 3 OFF 20 Half Lamp Mode 2: All OFF 22 Half Lamp Mode 2: No. 2 ON, No. 1, 3, 4 OFF 24 Half Lamp Mode 2: No. 3 ON, No. 1, 2, 4 OFF 26 Half Lamp Mode 2: No. 2, 3 ON, No. 1, 4 OFF NOTE: If you receive a response that is not found in these tables then the projector is in transition of lamp modes. Resend the command in one (1) minute. Table PC Type Read See below chart Stand by AV Mode Go PC adj. No signal sssss Meaning Projector is OFF. Current source is video. PC System is set to AUTO No source on current input. Where sssss is the name of an RGB source that s in the PC System window look up table.
12 12 05/06/06 Table 4.A A Input Mode Read s(cr) s: Meaning 1 Input 1 is currently selected and being displayed. 2 Input 2 is currently selected and being displayed. 3 Input 3 is currently selected and being displayed. 4 Input 4 is currently selected and being displayed. Extended Status Request Commands Extended Status request commands are used to poll the projector for the setting or mode of various projector characteristics. Status request commands follow the protocol: CR_xx(CR) Where _ is a space and XX is the status item code (See Table 4a for a complete list of status item codes and descriptions) and (CR) is 0D. Table 4a: Extended Status Request Codes Command Function Code BRIGHT Get Brightness Value nnn Parameters CONT Get Contrast Value nnn COLOR Get Color Value nnn TINT Get Tint Value nnn SHARP Get Sharpness Value nnn GAMMA Get Gamma Value nnn VOLUME Get Volume Value nnn COLTEMP Get Color Temp Value nnn DENHCR Get Digital Enhancer Value nnn BASS Get Bass Value nnn TREBLE Get Treble Value nnn
13 13 05/06/06 BLTINSP Get Built in Speaker Status ON, OFF FSYNC Get Fine Sync Value nnn TDOTS Get Total Dots Value nnn CLAMP Get Clamp Value nnn H-POS Get Horizontal Position Value nnn V-POS Get Vertical Position Value. nnn FLSCREN Get Full Screen Status ON, OFF HMLAMP Total Number of Lamps nnn PROJH Total Projector Lamp Hours nnnnnnn INFLAMP Get Lamp Status PRESSURE Get Air Pressure Value nnnn IDSLOT1 Get ID of Slot 1 IDSLOT2 Get ID of Slot 2 IDSLOT3 Get ID of Slot 3 IDSLOT4 Get ID of Slot 4 WBAL-R Get White Balance Red Value nnn WBAL-G Get White Balance Green Value nnn WBAL-B Get White Balance Blue Value nnn IMAGE Get status of image mode INPUT Get status of input 1-4 NML ( lamp can be changed) CNG (lamp is cooling down, can t be changed) 00 = Video 01 = D-Sub 02 = Faroudia 03 = LAN 04 = Component 05 = DVI 06 = HD-SDI 99 = No Card Standard - STAND Real - REAL Cinema - CINEMA Image - IMAGE1~4 Custom - Custom1~4 SOURCE Get Status of which Source is selected Computer Signal DIGITAL, ANALOG Video Signal VIDEO, S-VIDEO, YPBPR, YCBCR,HD-SDI, BLANK SCREEN Get status of Screen size NORMAL, WIDE SYSTEM LANG Get Status of System Get status on which language is selected AUTO, NTSC, NTSC443, PAL, SECAM, PAL-M, PAL-N, 1080i, 1035i, 720p, 575p, 480p, 575i, 480i English ENG German DEU French FRA Spanish ESP Italian ITA Portuguese POR Dutch NED Swedish SVE Japanese JPN Korean - KOR
14 14 05/06/06 Chinese - CHI ON-STA Get status of Select ON Start ON, OFF P-MANE Get status of power management setting ON, OFF PROJH Get status of projector hours nnnnnnn SIGNAL Get status of Signal SERSYS Get info on which signal is selected BBACK Get status of blue background ON, OFF DISP Get status of Display ON, OFF LOGO Get status of Logo ON, OFF VMUTE Get status of Video Mute ON, OFF FREEZE Get status of Freeze setting ON, OFF There is a signal ON There is no signal OFF 1080I60, 1080I I, 720P, 575P, 480P, 575I, 480I, NO SIGNAL PTIMER Get status of Timer Working ON Stop STOP Not Working OFF RCODE Get status of Remote Code Code1 001, Code2 002 LAMPMODE Get status of Lamp Mode FULL, HALF NZRED Get status of Noise Reduction ON, OFF PROGV Get status of Progressive Video ON, OFF FANSPEED Get status of Fan Speed Control Maximum MAX Normal NOR MUTE Get status of Mute ON, OFF LAMPREPL Get information of when lamp should be replaced nnnnn IMGGMD Get status of Image Gamma STD, REAL, CNM SRCINP1 Get status of Source 1 SRCINP2 Get status of Source 2 SRCINP3 Get status of Source 3 SRCINP4 Get status of Source 4 TEMPFAIL TEMPWARN Get status of temp when projector fails Get status of temp when projector is close to failing S-VIDEO, HD-SDI, NOCARD, BLANK S-VIDEO, HD-SDI, NOCARD, BLANK S-VIDEO, HD-SDI, NOCARD. BLANK S-VIDEO, HD-SDI, NOCARD, BLANK nn.ns nn.ns nn.ns nn.ns
15 15 05/06/ Controlling Multiple Projectors You can control multiple projectors using the RS232C loop-through output. By daisy chaining (connect the PC RS232 to the RS232 IN of one projector and then connect the RS232 OUT of that projector to the RS232 IN of another projector and so on), one PC can control multiple projectors. 1. Setting the Projector s Address Set specific address number for each projector. 1 Turn projector on. 2 Enter the service mode. To enter the service mode, press the MENU and IMAGE button on the projector and hold for 2 seconds 3 Change the service Group to 10 using the left/right arrow key on the projector or remote control. Change the No. to 3 by pressing the up/down arrows on the projector or remote control. 4 Once set to 10-3, adjust the data to set the projector s address number. (Adjust the Data by pressing the VOLUME UP/DOWN button. Setting value must be different for each projector to control each one individually. 5 Turn projector off, allow to cool and power back up for the new address to take effect. WARNING: Do not attempt to adjust any other items while in the service menu. Doing so could render the projector inoperable and/or unsafe. 2. Sending Commands Add A + specific address number to the beginning of a usual command, and send it. Example 1 - Controlling One Projector in the Daisy Chain To change only projector of address number 15 to INPUT2. Send command: A015C06[CR] where A specifies that a unique projector address is being used 015 is the 3-digit address number in10 base (same as the address number set in the Service Menu. C06 is the command code to select INPUT 2 [CR] is carriage return or 0D. Note: Returning data is the same as connecting one projector to one PC. Example 2 - Broadcasting Commands To All Projectors When you want to turn all projectors on together. Send command: AFFFC00[CR] where A specifies that a unique projector address is being used FFF is the 3-digit address number used to address all projectors in the daisy chain. C00 is the command code to POWER ON [CR] is carriage return or 0Dh. Note: There is no returning data when you send a broadcast command. (There is no response from the projectors) CAUTION When sending commands, be sure to add the address number. If you send a command without adding the address number, it may cause a malfunction. This is because all of the projectors in the daisy chain will return data (like connecting one projector to one PC) and the returned data may be garbled.
Optoma EH1060 / EH1060i RS232 Command Table.
Optoma EH1060 / EH1060i RS232 Command Table. Baud Rate 9600 Data Bits 8 Parity Check None Stop Bits 1 Flow Control UART16550 FIFO None Disable Lead Code Projector ID Command ID space variable carriage
More informationProjector Management Application Version 7.00 Instruction Guide
Projector Management Application Version 7.00 Instruction Guide Contents 1 INTRODUCTION... 4 1.1 OUTLINE... 4 1.2 SYSTEM... 4 2 INSTALLATION... 5 2.1 SYSTEM REQUIREMENTS... 5 2.2 PROJECTOR MANAGEMENT APPLICATION
More informationProjection Display. Serial Interface Specification
Projection Display Serial Interface Specification Version: 2.0 Projection Display Serial Interface Spec. 1/1 Table of Contents 1. RS232 SETTING...3 2. CONTROL COMMAND STRUCTURE...3 3. CONTROL SEQUENCE...3
More informationThe LP770 projector uses RXD, TXD and GND lines for RS-232C control. For RS-232C cable, a reverse type cable should be used.
LP770 RS-232 Command Values Control the LP770 projector by using a personal computer The LP770 projector can be controlled by connecting a personal computer with an RS-232C interface. Functions that can
More informationExternal Control Manual. (for PDP-614MX)
External Control Manual (for PDP-614MX) PDP614MX_232Config.doc Application These specifications are applicable to plasma monitors and communications control from external equipment. Connections Connections
More informationOPERATING GUIDE. HIGHlite 660 series. High Brightness Digital Video Projector 16:9 widescreen display. Rev A June A
OPERATING GUIDE HIGHlite 660 series High Brightness Digital Video Projector 16:9 widescreen display 111-9714A Digital Projection HIGHlite 660 series CONTENTS Operating Guide CONTENTS About this Guide...
More informationRS232 Commands and Protocol Function List. RS232 Pin Assignments. Spec. (from projector side) 1 N/A 2 RXD 3 TXD 4 N/A 5 GND 6 N/A 7 N/A 8 N/A 9 N/A
RS232 Commands and Protocol Function List RS232 Pin Assignments 9 5 2 Pin no. Spec. (from projector side) 1 N/A 2 RXD 3 TXD 4 N/A 5 GND 6 N/A 7 N/A 8 N/A 9 N/A 58 RS232 Protocol Function List 1. There
More informationisync HD & isync Pro Quick Reference Guide isync HD isync Pro Digital Video Processor and Video/Audio Switcher
isync HD & isync Pro Digital Video Processor and Video/Audio Switcher Quick Reference Guide isync HD Key Digital, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge
More informationControl Application Guide Version 4.0. Revision History. Revision Date Page(s) Changed Description of Change 4/2009 All pages First edition released.
3M Digital Projector Control Application Guide Version 4.0 Revision History Revision Date Page(s) Changed Description of Change 4/2009 All pages First edition released. Intended Use The 3M Digital Projectors
More informationControling the projector using a personal computer
Data Projector EX100U / ES100U Controling using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : Turning the power
More informationDLA-HD350 / DLA-HD750 DLA-HD550 / DLA-HD950 DLA-HD990 DLA-RS10 / DLA-RS20 DLA-RS15 / DLA-RS25 DLA-RS35. RS-232C and Infrared Remote Control Guide
JVC D-ILA Projector DLA-HD350 / DLA-HD750 DLA-HD550 / DLA-HD950 DLA-HD990 DLA-RS10 / DLA-RS20 DLA-RS15 / DLA-RS25 DLA-RS35 RS-232C and Infrared Remote Control Guide Version 1.1 Contents Introduction...2
More informationAppendices. RS232 Commands and Protocol Function List. RS232 Pin Assignments. 57 English. RS232 shell is grounded.
RS232 Commands and Protocol Function List RS232 Pin Assignments 1 2 3 RS232 shell is grounded. Pin no. Spec. (from projector side) 1 TXD 2 RXD 3 GND 57 English RS232 Protocol Function List 1. There is
More informationDigital Projector X66 Operator's Guide
Digital Projector X66 Operator's Guide Thank you for purchasing this projector. WARNING WARNING CAUTION NOTE Trademark acknowledgment 1 Content About this manual.... 1 Content.... 2 Projector features....
More informationAppendices. RS232 Commands and Protocol Function List. RS232 Pin Assignments. English. RS232 shell is grounded.
RS232 Commands and Protocol Function List RS232 Pin Assignments 9 6 RS232 shell is grounded. 2 Pin no. Spec. (from projector side) 1 N/A 2 RXD 3 TXD 4 N/A 5 GND 6 N/A 7 N/A 8 N/A 9 N/A 64 RS232 Protocol
More informationControling the projector using a personal computer
LCD Projector XL8U / SL4U Controling using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : Turning the power ON
More informationOPERATING GUIDE. M-Vision Cine 3D series. High Brightness Digital Video Projector 16:9 widescreen display. Rev A August A
OPERATING GUIDE M-Vision Cine 3D series High Brightness Digital Video Projector 16:9 widescreen display 112-022A Digital Projection M-Vision Cine 3D series CONTENTS Operating Guide CONTENTS About this
More informationControlling the projector using a personal computer
DLP Projector WD510U/WD510U-G WD500U-ST Controlling using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : Turning
More informationEXTERNAL CONTROL THROUGH RS-232C
EXTERNAL CONTROL THROUGH RS-232C The RS-232C port allows you connect the RS-232C input jack to an eternal control device (such as a computer or an A/V control system) to control the TV s functions eternally.
More informationPORTABLE LCD PROJECTORS
PORTABLE LCD PROJECTORS CPX4 CPX7 CPX8 CPWX8 CPX9 The HD ready logo (and all references to HD) applies to CPWX8 only Impressive presentations on the go A projector for today s mobile professional Combining
More informationControlling the projector using a personal computer
DLP TM Projector XD435U / XD430U / SD430U / XD420U / SD420U Controlling using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable
More informationControl Application Guide Version 4.12
3M Digital Projector Control Application Guide Version 4.12 For Models: X21i / X26i / X30n / X31/ X31i / X35n / X36 / X36i / WX36 / WX36i / X46 / X46i / X56 / X62w / X64w / X70 / X75 / X80 / X90 / X90K
More informationAppendices. RS232 Commands and Protocol Function List. RS232 Pin Assignments. 51 English. RS232 shell is grounded.
RS232 Commands and Protocol Function List RS232 Pin Assignments 1 2 3 RS232 shell is grounded. Pin no. Spec. (from projector side) 1 TXD 2 RXD 3 GND 51 English RS232 Protocol Function List 1. There is
More informationLCD Projector XL30U / XL25U / SL25U
LCD Projector XL30U / XL25U / SL25U This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions : Turning the power ON or OFF Changing input signals
More informationhp xp8010 series digital projector rs232 protocol reference
hp xp8010 series digital projector rs232 protocol reference 1 1 Notice This manual and any examples contained herein are provided as is and are subject to change without notice. Hewlett-Packard Company
More informationDATA PROJECTOR XJ-S30/XJ-S35
E DATA PROJECTOR XJ-S30/XJ-S35 User s Guide Be sure to read the precautions in the separate User s Guide (Basic Operation). For details about setting up the projector and lamp replacement, see the User
More informationInstaller Guide. Follow these instructions to set up the PowerLite Pro Cinema 1080 projector and HQV video processor.
Installer Guide Follow these instructions to set up the PowerLite Pro Cinema 1080 projector and HQV video processor. For more information, see the manuals that came with these products. Setting Up the
More informationXG-PH80W-N XG-PH80X-N SETUP MANUAL DATA PROJECTOR MODEL
DATA PROJECTOR MODEL XG-PH80W-N XG-PH80X-N SETUP MANUAL Setting up the Screen...2 Screen Size and Projection Distance...3 Connecting Pin Assignments...14 RS-232C Specifications and Commands...16 Setting
More informationDLP PROJECTOR FEATURES USER S GUIDE OUTLINE. 1. High Brightness. 2. High Resolution. 3. Compact Size, Feather Weight for Portability
DLP PROJECTOR USER S GUIDE Thank you for purchasing the DLP TM Projector. Please read this user s guide to ensure correct use of the device. Save this user s guide for future reference. OUTLINE This DLP
More informationQuick Reference Guide
Multimedia Projector Quick Reference Guide MODEL 103-011100-01 Projection lens is optional. English Use this book as a reference guide when setting up the projector. For detailed information about installation,
More informationDurable and Reliable Design for 24/7 Use. Overview. Narrow Bezel Optimized for Video Walls. 42 Narrow bezel commercial LED display
Durable and Reliable Design for 24/7 Use 42 Narrow bezel commercial LED display Overview The ViewSonic CDP4260-L is a 42 (42 viewable) commercial LED display designed for use 24 hours a day, 7 days a week.
More informationAppendices. RS232 Commands and Protocol Function List. RS232 Pin Assignments. 81 English. RS232 shell is grounded.
RS232 Commands and Protocol Function List RS232 Pin Assignments 1 2 3 RS232 shell is grounded. Pin no. Spec. (from projector side) 1 TXD 2 RXD 3 GND 81 English 1. There is a after all ASCII commands.
More informationEH320USTi. 1080p ultra short throw interactive projection. TouchBeam finger touch interactive. Bright projection 4000 ANSI lumens
EH320USTi 1080p ultra short throw interactive projection TouchBeam finger touch interactive Bright projection 4000 ANSI lumens Full HD 1080p resolution, 2x HDMI input and 16W audio Crestron RoomView RJ45
More informationVPL-DX220. 2,700 lumens XGA desktop projector. Overview
VPL-DX220 2,700 lumens XGA desktop projector Overview Efficient, easy-to-use projector for classrooms and meeting rooms: with excellent picture quality and low ownership costs. The VPL-DX220 XGA projector
More informationUSER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE
HIGHlite Laser 3D Series High Brightness Digital Video Projector USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REFERENCE GUIDE 114-913B Digital Projection HIGHlite Laser
More informationDiD. LCD Video Monitor & Video Wall Universal User Manual. Digital Information Display
LCD Video Monitor & Video Wall Universal User Manual DiD Digital Information Display Video Monitor Models M82S1/M70S1/M65S1/M55S1/M46S1/M40S1/M32S1/M24S1/M19S2/M19S1 Video Wall Models PD55N3/PD46N4/PD46N3/PD46N2/PD40N2
More informationKramer Electronics, Ltd. USER MANUAL. Model: VP-437xl. Presentation Switcher / Scaler
Kramer Electronics, Ltd. USER MANUAL Model: VP-437xl Presentation Switcher / Scaler Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 3.1 Recommendations for Best Performance
More informationUSER MANUAL. HIGHlite Laser 3D Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE REFERENCE GUIDE
HIGHlite Laser 3D Series High Brightness Digital Video Projector USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE REFERENCE GUIDE 114-913A Digital
More informationRS-232 terminal Product Interface specifications
RS-232 terminal Product Interface specifications Communication configuration To control the projector from an LCD control panel, connect an RS-232 cable to the serial control connector on the projector
More informationPart names (continued) Remote control
Introduction Part names (continued) Remote control (1) STANDBY ( 25) (1) (2) ON ( 25) (3) (3) ID - 1 / 2 / 3 / 4 s ( 18) (4) (4) COMPUTER 1 ( 27) (7) (5) COMPUTER 2 * (8) (6) COMPUTER 3 * (10) (13) (7)
More information3,500 ANSI Lumen SVGA with HDMI Business & Education Projector
3,500 ANSI Lumen SVGA with HDMI Business & Education Projector PA502S The ViewSonic PA502S projector for presentations offers impressive visual performance in small sized meeting rooms and classrooms.
More informationKRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-436N Presentation Switcher/Scaler. P/N: Rev 1
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-436N Presentation Switcher/Scaler P/N: 2900-300149 Rev 1 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 3 Overview 3
More informationVPL-DX131. 2,600 lumens XGA Desktop projector. Overview
VPL-DX131 2,600 lumens XGA Desktop projector Overview Economical desktop projector for office and classroom, offering high performance and superior ease of use The VPL-DX131 is packed with features optimised
More informationHIGHlite 660 3D Series High Brightness Digital Video Projector
HIGHlite 660 3D Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-242E About This Document Follow the instructions
More informationMULTIMEDIA PROJECTOR MODEL XG-PH70X XG-PH70X-N SETUP MANUAL
MULTIMEDIA PROJECTOR MODEL XG-PH70X XG-PH70X-N SETUP MANUAL Setting up the Screen... 2 Screen Size and Projection Distance... 3 Connecting Pin Assignments... 0 RS-232C Specifications and Commands... 2
More informationHIGHlite Laser 3D Series High Brightness Digital Video Projector
HIGHlite Laser 3D Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-913C About This Document Follow the instructions
More informationPB2220/ PB2120 FEATURES DLP PROJECTOR USER S GUIDE OUTLINE
DLP PROJECTOR PB2220/ PB2120 USER S GUIDE Thank you for purchasing the BenQ DLP Projector. Please read this user s guide to ensure correct use of the device. Save this user s guide for future reference.
More informationUSER MANUAL. E-Vision 6500 Series INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE
LENS SHIFT ZOOM AUTO MENU E-Vision 6500 Series High Brightness Digital Video Projector USER MANUAL INSTALLATION AND QUICK-START GUIDE CONNECTION GUIDE OPERATING GUIDE REMOTE COMMUNICATIONS GUIDE ENTER
More information8. How to program by RS232
8 How to program by RS232 Projection Display Serial Interface 8-1 RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit: 1 Flow Control None Minimum delay for next command: 1ms 8-2 Control
More informationCP-255ID Multi-Format to DVI Scaler
CP-255ID Multi-Format to DVI Scaler Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility
More informationRS-232. D8800 Series
RS-232 D8800 Series SERIAL INTERFACE SPECIFICATIONS Transfer Specifications Item Transmission Speed 38400 bps Data Length 8 bit Parity None Stop Bit 1 Flow Control None Specifications RS-232 Commands There
More informationVPL-EX430. 3,200 lumens XGA compact projector. Overview. The VPL-EX430 projector is ideal for mid-sized classrooms and meeting rooms.
VPL-EX430 3,200 lumens XGA compact projector Overview Present clear, bright images, with flexible connectivity and low running costs The VPL-EX430 projector is ideal for mid-sized classrooms and meeting
More informationCaptiva Serial API Commands
Technical Reference 020-102032-02 Captiva Serial API NOTICES COPYRIGHT AND TRADEMARKS All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.
More informationUSER MANUAL. VP-437N Presentation Switcher/Scaler MODEL: P/N: Rev 3
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-437N Presentation Switcher/Scaler P/N: 2900-300156 Rev 3 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationP-2 Installing the monitor (continued) Carry out as necessary
P-2 Installing the monitor (continued) Carry out as necessary Using the monitor without the bezel MDT552S satisfies the UL requirements as long as it is used with the bezel attached. When using the monitor
More informationVideo Scaler Pro with RS-232
Video Scaler Pro with RS-232 - ID# 783 Operation Manual Introduction Features The Video Scaler Pro with RS-232 is designed to convert Composite S-Video and YCbCr signals to a variety of computer and HDTV
More informationIndicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.
User s Guide 1 Notations Used in This Guide 2 f Safety Indications So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible
More informationMulti-format to HDMI scaler ID#15107
Multi-format to HDMI scaler ID#15107 Operation Manual Introduction The Digital Video Scaler has CV, SV, HD, Composite, PC, HDMI and SDI inputs and can scale the signal into HDMI, VGA with audio output
More informationVPL-DX102. 2,300 lumens XGA Desktop projector. Overview
VPL-DX102 2,300 lumens XGA Desktop projector Overview Economical desktop projector for office and classroom, offering high performance and superior ease of usethe VPL-DX102 is packed with features optimised
More informationBenQ PB8220 PB8120. User s Guide
BenQ PB8220 PB8120 User s Guide Copyright Copyright 2003 by BENQ Corporation (formerly Acer Communications & Multimedia Inc.). All rights reserved. No part of this publication may be reproduced, transmitted,
More information4200 ANSI Lumens 1080p DLP Projector with Up to 15,000 Hours Lamp Life
4200 ANSI Lumens 1080p DLP Projector with Up to 15,000 Hours Lamp Life PG705HD The ViewSonic PG705HD is a high brightness projector that combines 4200 ANSI lumens and 1080p resolution to project images
More informationFull HD 3D home cinema projector with Reality Creation, SXRD panels, Bright Cinema and TV modes
VPL-HW55ES Full HD 3D home cinema projector with Reality Creation, SXRD panels, Bright Cinema and TV modes Overview An outstanding cinematic experience The VPL-HW55ES is a fantastic option for movie lovers
More informationIndicates the possibility of death or serious injury if this symbol is ignored or if sufficient care is not taken.
User's Guide 1 Notations Used in This Guide 2 f Safety Indications So that you can use the projector safely and correctly, symbols are applied in the documentation and on the projector to indicate possible
More informationUSER MANUAL. VP-443 Presentation Switcher/Scaler MODEL: P/N: Rev 5
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-443 Presentation Switcher/Scaler P/N: 2900-300084 Rev 5 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More information4000 ANSI Lumen WXGA DLP Projector
4000 ANSI Lumen WXGA DLP Projector PG703W The ViewSonic PG703W are high brightness WXGA projectors respectively, featuring 4000 ANSI Lumens and high 22,000:1 contrast ratio to produce the finest of details
More informationComing to a living room near you...
Home Cinema Movie magic An evening at the movies has just got even better. With Hitachi s Home Cinema Projectors, you can enjoy films, sporting events and family movies on the big screen but from the comfort
More informationRS-232C, LAN and Infrared Remote Control Guide FOR MODELS: Version 1.4. Contents
JVC D-ILA Projector RS-232C, LAN and Infrared Remote Control Guide FOR MODELS: DLA-HD350 DLA-HD750 DLA-HD550 DLA-HD950 DLA-HD990 DLA-X3 DLA-X7 DLA-X9 DLA-X30 DLA-X70R DLA-X90R DLA-RS10 DLA-RS20 DLA-RS15
More informationCSLUX-300I Multi-Format to HDMI Scaler
CSLUX-300I Multi-Format to HDMI Scaler Operation Manual SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.
More informationLCD VALUE SERIES (32 inches)
LCD VALUE SERIES (32 inches) http://www.orionimages.com All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein 1. SAFETY INSTRUCTION
More informationVPL-D200 Series. Data Projectors VPL-DW240 VPL-DX270 VPL-DX240 VPL-DX220
VPL-D200 Series Data Projectors VPL-DW240 VPL-DX270 VPL-DX240 VPL-DX220 Projector for office and meeting room, offering basic high performance and superior ease of use The features of the VPL-D200 Series
More informationCommand line direct mode: This is relevant when a PC application is used to send and receive commands over the network port.
Serial Command Structure The Optika Collaborate UHD series feature an RJ-45 Ethernet port for control and monitoring over a network. This application note introduces the two user interface modes: Command
More informationCSLUX-300I Multi-Format to HDMI Scaler
CSLUX-300I Multi-Format to HDMI Scaler Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility
More informationVPL-VW1100ES. The ultimate 4K home cinema projector for larger, luxury private screening rooms. Overview
VPL-VW1100ES The ultimate 4K home cinema projector for larger, luxury private screening rooms Overview More than 4x the resolution of Full HD The VPL-VW1100ES projector brings the fully immersive experience
More informationModel No. I I I I I I I I
I I I I I I I I Functional Instructions Model No. LCD Projector PT-AE4000U Thank you for purchasing this Panasonic product. For your own safety, please read Precautions with regard to safety of the operating
More informationVideo to DVI 1080p Scaler Box - ID# 796
Video to DVI 1080p Scaler Box - ID# 796 Operation Manual Introduction Video to DVI 1080p Scaler Box is an upgraded design to convert Standard Definition Composite Video (CV) and S-Video (SV) signals to
More informationHIGHlite 740 Series High Brightness Digital Video Projector
HIGHlite 740 Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REFERENCE GUIDE 114-751I About This Document Please follow the instructions
More informationTrue Home Cinema Experience
Home Cinema Projectors 16 : 9 WIDE PANEL True Home Cinema Experience 1 High-resolution 16:9 wide-screen LCD panels for extra picture quality 2 Extra short-throw lens allows display of large images in small
More informationDH1017. Make a bright impact. High resolution for stunning clarity. Full HD 1080p Lumens
DH1017 Make a bright impact High resolution for stunning clarity Full HD 1080p - 4200 Lumens Ultimate Control - Full support for Crestron, Extron, AMX, PJ-Link and Telnet LAN commands Extensive connectivity
More informationPB7200. PB7100 User s Manual
PB7200 BenQ PB7220 PB7100 User s Manual Copyright Copyright 2003 by BENQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
More informationKRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-437N Presentation Switcher/Scaler. P/N: Rev 2
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-437N Presentation Switcher/Scaler P/N: 2900-300156 Rev 2 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 3 Overview 3
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-201YC. 2x1 s-video Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-201YC 2x1 s-video Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VS-201YC 2x1 s-video Switcher 4 5
More informationEH320UST. 1080p Ultra Short Throw Projector. Bright projection 4000 ANSI lumens. Full HD 1080p resolution, 20,000:1 contrast ratio
EH320UST Bright projection 4000 ANSI lumens 1080p Ultra Short Throw Projector Full HD 1080p resolution, 20,000:1 contrast ratio 2x HDMI input and 16W audio Crestron RoomView RJ45 control and monitoring
More information3,600 ANSI Lumen SVGA with HDMI Business & Education Projector
3,600 ANSI Lumen SVGA with HDMI Business & Education Projector PA503S The ViewSonic PA503S offers impressive visual performance to improve presentations, ideal for use in small business meeting rooms and
More informationDIGI-SCAL-5 Installation Guide. Intelix
DIGI-SCAL-5 Installation Guide Intelix www.intelix.com Important notice: Do not attempt to disassemble or alter the scaler housing. There are no user-serviceable parts inside the unit. Doing so will void
More informationP42XP10-BK Installation Guide 42 Plasma Monitor Rev 1.2
Contents: Product Description and Notes Page 1 Tilt Angle and Rotation Page 1 Ventilation Requirements Page 2 Display Dimensions Front, Top, Bottom & Right Side Page 3 Rear Page 4 Cosmetic Colors Page
More information7 3G -SDI Monitor w/ Signal Conversion QUICKSTART GUIDE
What s included x Monitor x AC Adapter x Camera Shoe Mount (SM-0) x DV Battery Plate (Check one) Checked by DV BATTERY PLATES -: Canon 900, Sony L, Panasonic D Battery Plates VX7 c-: Canon E6, Nikon EL,
More informationSpecification of Main Parts LCD Size 0.76-inch (D10) Pixel Number 2,304,000 dots (1920 x 1200) x 3 Native Resolution WUXGA(16:10) Projection Lens Type Power zoom / Power focus / Power shift F-Number/ Focal
More informationE-Vision D Series High Brightness Digital Video Projector
LENS SHIFT ZOOM MENU E-Vision 6800 3D Series High Brightness Digital Video Projector 4INSTALLATION AND QUICK-START GUIDE 4CONNECTION GUIDE 4OPERATING GUIDE 4REMOTE COMMUNICATIONS GUIDE AUTO ENTER RETURN
More informationW320UST. Ultra Short Throw Projector. Bright projection 4000 ANSI lumens. WXGA resolution, 20,000:1 contrast ratio. 2x HDMI input and 16W audio
W320UST Bright projection 4000 ANSI lumens Ultra Short Throw Projector WXGA resolution, 20,000:1 contrast ratio 2x HDMI input and 16W audio Crestron RoomView RJ45 control and monitoring W320UST The W320UST,
More informationFor safe and correct use, be sure to read the Safety Information in Read This First before using the machine. Operating Instructions
For safe and correct use, be sure to read the Safety Information in Read This First before using the machine. Operating Instructions Table of Contents 1 Disclaimer...2 1. Using the Remote control... 3
More informationPT-DZ6710 PT-DZ6700 PT-DW6300 PT-D6000 PT-D5000
Functional Instructions DLP Based Projector Commercial Use Model No. PT-DZ6710 PT-DZ6700 PT-DW6300 PT-D6000 PT-D5000 The information of these instructions are shared use with multiple models of DZ6710
More informationDell 1510X Projector. User s Guide
Dell 1510X Projector User s Guide Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your projector. NOTICE: A NOTICE indicates either potential
More informationDisplays Open Frame Monitor Model Number: AND-TFT-150Bxx
Displays 15.0 Open Frame Monitor Model Number: AND-TFT-150Bxx The AND-TFT-150Bxx 15.0 Open Frame Monitor series are rugged, high performance Industrial LCD Monitors, designed for commercial and industrial
More information49 inch Full HD 3.5mm Ultra- Narrow Bezel 24/7 Tiling Support with DisplayPort or DVI video wall Commercial Display CDX4952 Ultra-narrow Bezel
49 inch Full HD 3.5mm Ultra- Narrow Bezel 24/7 Tiling Support with DisplayPort or DVI video wall Commercial Display CDX4952 With stunning brightness, vibrant images, and multi-screen tiling, the ViewSonic
More informationUSER MANUAL. VP-461 Video Scaler MODEL: P/N: Rev 1
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-461 Video Scaler P/N: 2900-300195 Rev 1 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 2 2.3
More informationVPL-FH500L. 7,000 lumens WUXGA 3LCD Higher Installation projector. Overview. Features
VPL-FH500L 7,000 lumens WUXGA 3LCD Higher Installation projector Overview Ultra high brightness and low maintenance - great performance for any environment The VPL-FH500L's outstanding portfolio of features
More informationX320UST. Ultra Short Throw Projector. Bright projection 4000 ANSI lumens. XGA resolution, 20,000:1 contrast ratio. 2x HDMI input and 16W audio
X320UST Ultra Short Throw Projector Bright projection 4000 ANSI lumens XGA resolution, 20,000:1 contrast ratio 2x HDMI input and 16W audio Crestron RoomView RJ45 control and monitoring X320UST The X320UST,
More informationOperating Instructions
Broadcast A/V Division Model No. M-LYNX-702W Dual 7 High Resolution Rack Mount Display with Waveform Operating Instructions V.1.0 Table of Contents 1. PRODUCT DESCRIPTION... 3 2. MENU SETTING... 6 3. SPECIFICATIONS...
More informationUSER MANUAL. VP-441 Presentation Switcher/Scaler MODEL: P/N: Rev 7
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: VP-441 Presentation Switcher/Scaler P/N: 2900-300040 Rev 7 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions
More informationX600. Make a bright impact. Proven Performance. XGA ANSI lumens
X600 Make a bright impact Proven Performance XGA - 6000 ANSI lumens Ultimate Control - Full support for Crestron, Extron, AMX, PJ-Link and Telnet LAN commands Extensive connectivity - HDMI, DisplayPort,
More informationRS-232C External Serial Control Specifications
RS-232C External Serial Control Specifications Applicable models: LT-37X898, LT-42X898, LT-47X898 and later models for North America 1. Connection 1.1. Terminal D-SUB 9Pin Male terminal Pin No. Name Pin
More information