RotorX RX122 Atom Building Guide
|
|
- Kellie Flynn
- 5 years ago
- Views:
Transcription
1 RotorX RX122 Atom Building Guide 1
2 What s included? 1x Atom CF 2mm Frame 1x Naze32 Flight Controller (Pre- flashed with Cleanflight) 1x pack of mounting hardware 1x JST pigtail 1x servo wire 1x 520tvl CMOS camera 1x Pololu Step- down voltage regulator 5V 1x MinimOSD (preflashed with Scarab OSD) 1x 5.8ghz VTX 600mw 32ch (Fatshark, Boscam compatible) 1x CL Antenna (RHCP) 4x DYS 20A ESC (SimonK with Comp_PWM enabled) 4x Custom made RotorX 1104 motors 1x PPM capable radio receiver (optional) RotorX custom 3020 props Recommended accessories: 3M double- sided tape, ¾ inch heatshrink ** NOTE ** We recommend using a variable temperature soldering iron, helping hands, a flux pen and good solder for better build quality This build requires making modifications to included electronics. RotorX and its dealers/resellers are not responsible for any defective parts that are the result of these modifications. 2
3 TABLE OF CONTENT PART 1: PREPPING ELECTRONICS... 4 A) ELECTRONIC SPEED CONTROLLER (ESC)... 4 B) FLIGHT CONTROLLER (FC)... 5 PART 2: INSTALLATION... 7 A) MOTORS... 7 B) ESC... 7 C) FC... 9 PART 3: FPV SYSTEM A) MICRO MINIMOSD B) CAMERA C) VTX (NEVER EVER POWER THE VTX WITHOUT AN ANTENNA ATTACHED, VTX WILL BE BURNT) PART 4: FINAL TOUCHES A) RADIO RECEIVER B) CAMERA MOUNTING C) FC D) OSD E) VTX
4 PART 1: PREPPING ELECTRONICS A) ELECTRONIC SPEED CONTROLLER (ESC) Remove signal and ground wires from all the ESCs. We will actually prepare these connections on the FC side first, after that we will cut the wires to length and solder back onto the ESC. That way there will be no excess wires. Given the size and weight of Atom, we minimize excess weight by removing unnecessary connectors and plugs. Therefore cut the servo plugs of those wires. You can discard those plugs Strip both ends of signal and ground wires, tin them 4
5 B) FLIGHT CONTROLLER (FC) Turn the board upside down, tin the signal and ground pads (1 through 4) on the ESC Headers rails. We will run the wires from underneath the board Turn the board right side up, tin RC Input pads as shown (power, ground, 1, 3 and 4) 5
6 Solder signal and ground wires on the board. Label them from 1 to 4 so we can identify them later 6
7 PART 2: INSTALLATION A) MOTORS Install motors using included hardware B) ESC Cut a piece of the included double- sided tape, enough to cover the ESC and use it to mount the ESC to the topside of the frame, on top of the motor wires. Make sure the power leads face inwards 7
8 - Battery + Take note that the motor wires are underneath the ESC. Once the ESCs have been positioned, cut the power and ground leads to length and solder them in daisy chain configuration as shown above. Use the included JST pigtail to connect to battery Tin the motor pads on the ESC. Roll the exposed tips of motor wires in a circle and tin them. Solder motor wires onto ESC pads Install Pololu on the frame, connect Vin and GND to the nearest ESC. Vout and GND will be connected to the FC later. 8
9 C) FC Mount the FC using provided hardware with USB port facing the left hand side (FC needs to be turn 90 degree in Cleanflight later on). Suggested method is using the 10mm standoffs below and 8mm ones on top of the FC. This will provide enough space to mount the radio receiver underneath the FC. Cut the signal and ground wires to length and solder it from FC to respective ESC. Solder 5V and GND wires from Pololu to one of the positive and ground pads on the ESC header rail. Solder the given servo wire to the GND, positive and RC input pad 1. 9
10 PART 3: FPV SYSTEM A) MICRO MINIMOSD Tin pads on MinimOSD as shown. Connect pad 3 and 4 (on the other side of the FC) to RX and TX on the MinimOSD respectively. Power MinimOSD by tapping into the nearest ESC header pads. 10
11 B) CAMERA CAMERA Cut the camera wires to length, usually about half the length, strip all wires and tin the tips. Solder the video signal and ground wires to Video In and GND on the MinimOSD. Solder power wire to the nearest 5V on ESC Header pad Connect the Battery monitor port on the FC to the nearest ESC. The FC will monitor battery voltage. By connecting pad 3,4 to Tx and Rx on the MinimOSD, the same information will be display on the OSD. 11
12 C) VTX (NEVER EVER POWER THE VTX WITHOUT AN ANTENNA ATTACHED, VTX WILL BE BURNT) Cut the SMA connector off the antenna Strip away about 1cm of the plastic jacket, be careful not to cut into the braided shielding. Remove the cover and twist the shielding into 2 strands. Strip away the dielectric insulator to expose about 2-3mm of the core. Don t tin the shielding strands and core yet. 12
13 Thread the core wire through the signal hole, spread the shielding on the pads. Solder the antenna directly onto the VTX: shielding to the 2 large pads, while core to the small hole in the middle. Use provided 3M tape to tape the VTX to the underside of the top plate, make sure the dip switch is aligned through the cut- out hole. Use ziptie to secure it to the top plate. VTX Use the other half of the camera wire, solder them to the VTX following the marking (5V, Ground, Video). Cut the connector off and solder the wires to the MinimOSD (Video out, Ground) and the 5V power of the ESC header rails. 13
14 PART 4: FINAL TOUCHES A) RADIO RECEIVER Solder the servo wire to the PPM output on your radio receiver of choice. Recommended mounting space for the receiver is underneath the FC ** Make sure your receiver is PPM capable and PPM mode is activated ** Do one final check through all solder joints, make sure everything is connected. Power up the system, check through your goggles to identify the top and bottom sides of the camera. B) CAMERA MOUNTING Camera Cut a few pieces of the provided 3M tape, each slightly shorter than the previous. Stick them to the bottomside of the camera like shown above. The more steps you have, the more aggressively the camera is angled. For beginner pilots, we recommend 1 to 2 layers of tape. Use 3 layers for casual flying and 4 to 5 for extreme racing. C) FC Connect your flight controller to Cleanflight and flash it with Cleanflight 1.9 (if not already) Configure your flight controller for Quad X configuration. Be sure to rotate the board 90 degree to the left (yaw 90 degree). Double check that board orientation is correct. Make sure that in Ports tab, MSP is checked for both UART1 and UART2 Check motor rotation, swap any 2 wires on the same motor if rotation is wrong. Once everything is done, secure the ESCs and receiver antennas to the arms with heatshrink (3/4 inch heatshrink recommended) Secure the top plate using provided hardware D) OSD Power everything, make sure you can access the OSD, tune PIDs and rates through goggles. 14
15 E) VTX Please use the chart below for channel selection 15
16 ** YOUR BUILD IS NOW COMPLETE ** ** PLEASE CHECK OUT OUR CONFIGURATION GUIDE TO SET UP YOUR FLIGHT CONTROLLER ** 16
Atlatl HV V2. 5.8G FPV Video Transmitter. User Manual & Installation Guide
Atlatl HV V2 5.8G FPV Video Transmitter User Manual & Installation Guide Contents Overview... 1 Features Specifications Warranty Pinout Diagram and Channel Table... 3 Installation Guide... 4 Functions...
More informationAtlatl FPV Video Transmitter
Atlatl FPV Video Transmitter User Manual & Installation Guide V1.0 Contents Overview... 1 Features Specifications Warranty Pinout Diagram and Channel Table... 2 Installation Guide... 3 Functions... 6 Channel-Change
More informationTBS UNIFY 5G8 200mW 32ch Video Tx High quality, long range, micro video transmitter
TBS UNIFY 5G8 200mW 32ch Video Tx High quality, long range, micro video transmitter Revision 2015-07-13 The TBS Unify is a new line of video transmitters, optimized for compatibility across multiple platforms
More informationTBS UNIFY PRO 5G8 (HV) Video Tx
TBS UNIFY PRO 5G8 (HV) Video Tx High quality, license-free, ultra-tiny, race ready vtx Revision 2017-08-15 The TBS UNIFY is a new line of video transmitters, optimized for compatibility across multiple
More informationBuilders guide Kinetic Aerial Air-Ro
Builders guide Kinetic Aerial Air-Ro Safety First Please build, fly and configure your drone safely. Moving propellers and mishandled lithium batteries can cause serious damage to person and property.
More informationTBS UNIFY PRO 5G8 (HV) Video Tx
TBS UNIFY PRO 5G8 (HV) Video Tx High quality, license-free, ultra-tiny, race ready vtx Revision 2018-03-03 The TBS UNIFY is a new line of video transmitters, optimized for compatibility across multiple
More informationTBS UNIFY PRO 5G8 (HV) Video Tx High quality, license-free, ultra-tiny, race ready vtx
TBS UNIFY PRO 5G8 (HV) Video Tx High quality, license-free, ultra-tiny, race ready vtx Revision 2016-10-10 The TBS UNIFY is a new line of video transmitters, optimized for compatibility across multiple
More informationTBS UNIFY PRO 5G8 (HV) Video Tx High quality, license free, ultra tiny, race ready
TBS UNIFY PRO 5G8 (HV) Video Tx High quality, license free, ultra tiny, race ready Revision 2016-03-01 The TBS Unify is a new line of video transmitters, optimized for compatibility across multiple platforms
More informationTBS UNIFY 2G4 500mW / 800mW 16ch Video Tx High quality, long range, micro video transmitter
TBS UNIFY 2G4 500mW / 800mW 16ch Video Tx High quality, long range, micro video transmitter Revision 2014-07-11 The latest and greatest 2G4 video transmitter from the leaders in long range technology.
More informationG4HUP Panoramic Adaptor Installation TS2000
G4HUP Panoramic Adaptor Installation TS2000 These instruction cover installation of the PAT board in the 2 nd IF of the TS2k 10.695MHz this gives access to all receiver options on the main receiver, including
More informationGetting Started Guide
Getting Started Guide International edition Rev 1.0 - May 2015 WARNING To use dogs as a good analogy, if the DJI Phantom is a white fluffy Poodle, the Vortex is a Pitt Bull, bred for fighting, and ready
More informationCONNEX ProSight. Installation and Operation Guide
CONNEX Installation and Operation Guide Copyright 2016 Amimon LTD, All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
More informationQuick-Start Guide. Distributed in the UK by: J Perkins Distribution Ltd, Lenham, Kent, UK ME17 2DL.
Quick-Start Guide Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product contains chemicals known to the State
More information250 Pro Getting Started Guide
250 Pro Getting Started Guide International edition Rev 1.0 - Dec 2015 Every Vortex 250 Pro is flight tested before leaving the factory. Flight Tested By: WARNING Congratulations on your purchase of one
More informationChecklist v05b pag 1
Sky Rider drone Check list Pre flight checks and tests Tail LED color codes Blue steady -> Radiocontrol is linked to the receiver. Blue flashing -> Headless mode On. Red steady -> Compass is calibrated.
More informationG4HUP Panoramic Adaptor Installation FT950
G4HUP Panoramic Adaptor Installation FT950 These instruction cover installation of the PAT board in the 1st IF of the FT950 69.45MHz this gives access to all receiver options on the main receiver. The
More informationiosd (On Screen Display)
iosd (On Screen Display) User Manual V1.4 2012-12-04 www.dji-innovations.com 2012 DJI Innovations. All Rights Reserved. 1 Disclaimer Thank you for purchasing product(s) from DJI Innovations. Please read
More informationBionic Elephant Trunk. Assembly Instructions
Bionic Elephant Trunk Assembly Instructions Equipment and Supplies Required items from the Bionics Kit and/or Materials Pack: 1. Tail fin (small) assembled 2 see Start Here for tail fin assembly instructions
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-500-1000 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around
More informationUser Manual & Setup Guide v1.1
User Manual & Setup Guide v1.1 Contents Overview... 1 Features Specifications Warranty and Return Policy Spare Parts... 3 Install Betaflight... 4 Install the Receiver... 7 Bind the Receiver... 8 Verify
More informationMCX Miniature Coaxial Connectors
ONLINE CATALOG MCX Miniature Coaxial Connectors 104 John W. Murphy Drive P.O. Box 510 New Haven, CT 06513 www.aepconnectors.com e-mail: aepsales@aepconnectors.com Mating Interfaces MCX Miniature Coaxial
More informationBinary s UFO Inventors Manual
Binary s UFO Inventors Manual - Parents please read the instructions carefully with your children prior to first use. - Please keep this instruction manual as it contains important safety information -
More informationSnail Fence InteleCell Deployment Guide
Snail Fence InteleCell Deployment Guide Preparation 1. Prepare deployment trip by making sure you have the following materials and tools when you fly up to the site: InteleCell NEMA Enclsoure (grey plastic
More informationManual. HoTT Hornet 250 Tricopter No No C No CAM. Copyright Graupner/SJ GmbH
EN Manual HoTT Hornet 250 Tricopter No. 16540 No. 16540.C No. 16540.CAM Copyright Graupner/SJ GmbH Index Introduction... 4 Service Centre... 4 Intended use... 5 Package content... 5 Symbols explication...
More informationNon Magnetic Connectors
Non Magnetic Connectors Johnson Components builds coaxial connectors using innovative materials and design to provide Mil Spec Performance at a commercial price. Now we offer our Non Magnetic Connectors
More informationInstallation Overview
Installation Overview Overview This chapter presents cable preparation and installation procedures for coaxial cables. Many connectors and special-purpose installation tools required for these cables are
More informationFPV PRO RACE EDITION TRI-DIVERSITY VIDEO CONTROLLER
DIVERSITY DEMON FPV PRO RACE EDITION TRI-DIVERSITY VIDEO CONTROLLER Diversity Demon is a video controller that is used to bridge three wireless video receivers together. Multiple receivers are used to
More information3 Foam Sealed Closure 2" (50 mm) with Compound Compression
3 Foam Sealed Closure 2" (50 mm) with Compound Compression Instructions 1.0 General 1.1 The 3M Foam Sealed Closure is designed to be used in the construction and maintenance of buried and underground PIC
More informationTBS CAIPIRINHA Mini FPV Wing
TBS CAIPIRINHA Mini FPV Wing Small, lightweight, fly anywhere plane Revision 2013 05 27 The new wing from TBS. Bittersweet, precise and easy to build, just like the cocktail it has been named after. Using
More informationDelvcam DELV-FPV-7 User Guide
Delvcam DELV-FPV-7 User Guide IMPORTANT SAFETY INSTRUCTIONS: Please read User Guide before using this product. Please keep User Guide for future reference. Please read the cautions to prevent possible
More informationProduct model and standard
Preface Thank you for purchasing the Ikan Blitz 400 HD Wireless Video System. This system features uncompressed high definition video with zero delay. Before using the product, please read this user s
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS
3M Cold Shrink QS4 Integrated Splice Kit QS4-35TS-350-1000 for Tape Shield, Wire Shield, UniShield, and Longitudinally Corrugated (LC) Cable Instructions IEEE Std. 404 35 kv Class 250 kv BIL F CAUTION
More informationIndustrial Loadbreak Elbow
Industrial Loadbreak Elbow 200 A 5, 8, and 15 kvclass 5810 Series Installation Instructions 1.0 General The 3M Industrial Loadbreak Elbow connector is a fullyshielded and insulated plug-in termination
More informationINVISILED ACCESSORIES
Indoor mounting accessories v" 5 feet LED-T-CH Aluminum Channel Includes a diffuser, two end caps, and five screws a" 2 pcs LED-T-CH-EC End caps for Aluminum Channel 1" 5 feet LED-T-CH1 Deep Aluminum Channel
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationSTRAIGHT TWO WAY JOINT3/C, PAPER INSULATED, SHIELDED, LEAD COVERED CABLE. Revised: October 10, 2008 Revised By: SGL Approved By: RHS SPLICES
STRAIGHT TWO WAY JOINT3/C, PAPER INSULATED, SHIELDED, LEAD COVERED CABLE I. INSTALLATION INSTRUCTIONS I.1. PRECAUTIONS: I.1.1. Expansion bends must be made in the cables to allow for cable movement while
More informationR/C Afterburner Light Kit For Electric EDF Jets 2009 Hyperdyne Labs
R/C Afterburner Light Kit For Electric EDF Jets 2009 Hyperdyne Labs http://www.hyperdynelabs.com Congratulations on purchasing the Afterburner light kit. Your kit is hand assembled in the USA, and we appreciate
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-4/0-500 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL CAUTION Working around energized
More informationFixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationEdge Connector Light Level Detector
Description This is a simple tutorial demonstrating how to use a Kitronik edge connector breakout with the BBC micro:bit. The tutorial will cover measuring ambient light levels with an LDR and dimming
More information3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0
3M Cold Shrink QS4 Integrated Splice Kit QS4-15JCN-2-4/0 for Jacketed Concentric Neutral (JCN) and Flat Strap Neutral Cable Instructions IEEE Std. 404 15 kv Class 150 kv BIL F CAUTION Working around energized
More informationContent BULK CABLES VIDEO CABLES AUDIO CABLES EXTENDERS USB CABLES ETHERNET CABLES VIDEO BALUNS CONNECTORS ADAPTERS PATCH PANELS & WALLPLATES TOOLS
Content BULK CABLES VIDEO CABLES AUDIO CABLES pages 2-8 pages 8-12 pages 12-13 EXTENDERS ETHERNET CABLES USB CABLES page 13 pages 14-15 pages 16-17 CONNECTORS ADAPTERS VIDEO BALUNS pages 17-23 pages 23-25
More informationSega MegaDrive 1 RGB Bypass Installation Guide Rev 1.1
Sega MegaDrive 1 RGB Bypass Installation Guide Rev 1.1 This step by step guide describes the Installation of the open source Voultar RGB Bypass Amplifier board for the original SEGA MegaDrive/Genesis 1.
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More information3M Better Buried Compound Compression Closure System
3M Better Buried Compound Compression Closure System Instructions March 2016 78-0015-2948-2-A Contents: 1.0 General...3 2.0 Kit Contents...3 3.0 Closure Selection Guide...4 4.0 LHS End Cap Installation...5
More informationNixie Clock Type Frank 2 Z570M
Assembly Instructions And User Guide Nixie Clock Type Frank 2 Z570M Software version: 7R PCB Revision: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 2 is a compact design with
More informationPowerBook G4 Aluminum 12" GHz LCD panel upgrade
PowerBook G4 Aluminum 12" 1-1.5 GHz LCD panel upgrade Upgrade a 1400x1050 LCD panel. Written By: martin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION The original LCD 1024x768 resolution
More informationHN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
More informationInstructions. Cable with Armor F CAUTION. October Rev A
3M Single Conductor Accessory Breakout Kits (BOK's) for use with 3M Cable Accessories (Terminations, T-Bodies and Push-On Elbows) For Use With Single Conductor Accessories On Three-Core Conductor Cables
More information3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT
3M Cold Shrink QS-III Silicone Rubber Splice Kit 5488A-TOW/WOT For Tape Over Wire (TOW) and Wire-Over-Tape (WOT) Shielded Cable For 250 2000 kcmil cable with 650-mil primary insulation thickness Instructions
More informationAP117 FY-OSD INSTALLATION & OPERATION MANUAL
November/3/2010 FEIYU TECH. AP117 FY-OSD INSTALLATION & OPERATION MANUAL Guilin Feiyu Electronic Technology Co., Ltd Rm. B305, Innovation Building, Information Industry Park, Chaoyang Road,Qixing District,GuiLin,CN
More informationCRYSTAL-800 W IRELESS IOS APP
1. Antenna Mount 2. HDMI Input (Type D Micro) 3. Sony L-Series Battery Mount (i.e NP-F970,NP-F570) 4. LED Status Lights 5. ON / OFF Button 6. 12V DC Input 7. BIND Button (for pairing TX and RX) 8. Frequency
More informationOCT 15 Rev B
AMP+ HVA280-3pxm XE High-Voltage Plug Connector with 1-Stage Latching Application Specification 114-32125 15 OCT 15 Rev B NOTE All numerical values are in metric units [with U.S. customary units in brackets].
More informationManual. Race copter alpha 250 Q. No hott. English
Manual Race copter alpha 250 Q No. 16520.hott English Index Index... 2 Introduction... 3 Service centre... 3 Intended use... 4 Package content... 4 Symbols explication... 5 Safety notes... 5 Preparation
More information3M Mini D Ribbon (MDR) Cable Assembly
3M Mini D Ribbon (MDR) Cable Assembly.050 Digital Camera Extension Cable 26 position 1WL26-TZ3B-XXX-03C Mates to popular 3M MDR 26 position receptacle on one end, and to another MDR 26 position cable assembly
More informationSDI-MP1010-GM-60P-M-RA 3G/HD-SDI Output Video Transceiver. SDI-MP1010-GM-60P-M-RA Features. Block Diagram SDI-MP1010-GM-60P-M-RA.
This is a family of small form factor modules for formatting and converting generic digital video streams to standard compliant formats. Different interface standards are supported from the transmitter
More informationAutomatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
More informationPRODUCT CATALOGUE 2010 Accessories
PRODUCT CATALOGUE 2010 Accessories Challange the distance with Inmak the antenna company CONTENTS CONNECTORS 110 ADAPT RS 115 SURGE PROTECTOR SP-1 116 SPLITTER INM SP2.4-2 117 SPLITTER INM SP5.8-2 117
More informationMUK REAR PANEL ASSEMBLY ASSEMBLY INSTRUCTIONS
Rev B. 13 August 2017 ASSEMBLY INSTRUCTIONS The Midnight Ultimate Keyer (MUK) consists of two functional assemblies: Rear Panel containing the interface and power connectors. Front Panel containing the
More informationScale Track System. 21 Century y Signal System 2-Rail Manual
Scale Track System st 21 Century y Signal System 2-Rail Manual TABLE OF CONTENTS Introduction...2-3 Road Signal Board Diagram and Definitions...4-6 Tips for Handling the Circuit Board...6 2-Rail Detector
More informationMulti-Media Installation Guide
Multi-Media Installation Guide Coaxial Page 2 Data Plug Page 7 Data Jack Page 10 Telephone Page 13 Splicing Page 15 Cable Types Cable Types Two basic types of cable are used in multimedia installations.
More informationMinimising the tuning drift effects due to external temperature variations in the Titanium Satellite C1W-PLL Wideband LNBF
Minimising the tuning drift effects due to external temperature variations in the Titanium Satellite C1W-PLL Wideband LNBF Although the Titanium LNB is named in the header, the comments which follow obviously
More informationCheck our knowledge base at
USER MANUAL Check our knowledge base at www.paralinx.net/support Copyright 2015 Paralinx LLC All Rights Reserved TABLE OF CONTENTS 1 Important Notice 10 LCD Screen 2 Safety Instructions 11 Indicators 3
More information[ Photos ] [ Wares ] [ Library ] [ Dave's Web ] [ Matt's Web ] Wares [ SWISH ] [ Simple Search ] [ Trunk Calc ]
[ Photos ] [ Wares ] [ Library ] [ Dave's Web ] [ Matt's Web ] Wares [ SWISH ] [ Simple Search ] [ Trunk Calc ] Realistic PRO-2006 Hardware Modifications Note Edited on January 1st, 1970, 00:00 UT. Improper
More informationGRANT RF CONTROL CENTER INSTALLATION INSTRUCTIONS Always disconnect battery while servicing or modifying the electrical system of the vehicle.
GRANT RF CONTROL CENTER INSTALLATION INSTRUCTIONS Always disconnect battery while servicing or modifying the electrical system of the vehicle. You will need standard hand tools, a Test Light and a Digital
More informationC2 +5V. (14) Vdd (+5 Vdc) (13) OSC1/A7 1.2K (12) 1.2K (11) 1.2K (10) U1 16F628 16F628A 1.2K (1) A2 1.2K (8) 1.2K (7) 1.2K. (Gnd) Vss (5) (6) 1.
CN1 Power Sw. SW1 CN2 C1 VR1 78L05 or LP2950ACZ- 5.0 +5V.1uf.1uf 9V Battery Fast Scan (Open) Slow Scan (Closed) Activity LED Reserved for LCD Serial Display R1 10K R2 10K SW2 CN3 LD1 R3 (16) (15) OS/A6
More informationMulti-Key v2.4 Multi-Function Amplifier Keying Interface
Multi-Key v2.4 Multi-Function Amplifier Keying Interface ASSEMBLY & OPERATION INSTRUCTIONS INTRODUCTION The Harbach Electronics, LLC Multi-Key is a multi-function external device designed for the safe
More informationE3/DS3 Tap. 6xBNC Type
E3/DS3 Tap 6xBNC Type CUSTOMER SUPPORT INFORMATION To order or for a technical information support: Phone: +33 3 88 10 18 30 or Fax: +33 3 88 10 18 35 Mail order: COMCRAFT 2, rue de la Mairie 67203 Oberschaeffolsheim
More informationModifying the RW1127 and similar TWTs for 24GHz
Modifying the RW1127 and similar TWTs for 24GHz Some notes by Brian G4NNS updated after the EME conference. Issue 1.04 During a visit from Johannes DF1OI he explained how Ulli DK3UC had modified Siemens
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationTL8651 3G/HD-SDI Output Video Transceiver. TL8651 Features. Block Diagram TL8651 3G/HD-SDI. 1080p p50
Thunder Link is a family of small form factor modules for formatting and converting generic digital video streams to standard compliant formats. Different interface standards are supported from the transmitter
More informationModel: S-4904T/R. Wireless HD Transmission System. User Manual. Please read this User Manual throughout before using.
Model: S-4904T/R Wireless HD Transmission System User Manual Please read this User Manual throughout before using. Preface Congratulations on your purchase of this product. Please read this user manual
More informationMCX - 75 Ohm Connectors
133-8333-001 4 133-8333-401 4 133-8334-001 4 133-8334-401 4 133-8433-001 3 133-8433-101 3 133-8434-001 3 133-8445-001* 3 133-8445-101* 3 133-8701-201 5 133-8701-211 5 133-8701-301 6 133-8701-311 6 133-8701-401
More informationIndoor/Outdoor Security System with Quad Monitor User s Manual
Indoor/Outdoor Security System with Quad Monitor User s Manual 4919539 Important! Please read this booklet carefully before installing or using these units. WARNING - These units should ONLY be opened
More informationDIN Connectors DIN06 E-03
DIN Connectors DIN0 E-0 Contents Introduction HOSIDEN DIN connectors are supplied to electronic equipment manufacturers both in Japan and overseas and are very well accepted because of high quality, a
More informationS7H-DK S7H 7" High Bright Monitor Deluxe Kit
S7H-DK S7H 7" High Bright Monitor Deluxe Kit QUICKSTART GUIDE What s Included 1 x S7H Monitor 1 x Camera Shoe Mount 1 x Neoprene Sleeve 1 x Mini-XLR to P-TAP Cable 2 x DV Battery Plate 1 x DV Battery 1
More informationHubsan Spy Hawk. John Stennard continues his coverage of First Person View flying with a review of a ready to fly camera plane
Hubsan Spy Hawk John Stennard continues his coverage of First Person View flying with a review of a ready to fly camera plane The Hubsan Spy Hawk is quite a bold attempt to produce a relatively low cost
More informationH2633IP-1 RELAY CARD K2633
H2633IP-1 RELAY CARD K2633 Control up to 4 high-power circuits from a low-power drive circuit. Features & Specifications The connection of a few relays to the outputs of an electronic circuit might be
More informationUAV Ultimate Atari Video A7800
UAV Ultimate Atari Video A7800 Basic Install guide because this is really easy mod to do! The UAV is a wonderful piece of tech for what it can do. To summarize, the UAV is a replacement video encoder and
More information24-Fiber LANLINXS (Model # ) 48-Fiber LANLINXS (Model # ) User Manual
24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual 24-Fiber LANLINXS (Model # 055-8632-5000) 48-Fiber LANLINXS (Model # 055-8832-5000) User Manual, Part Number
More informationManual. HoTT Hornet 250 Tricopter with mz-12 transmitter No RTF. Copyright Graupner/SJ GmbH
EN Manual HoTT Hornet 250 Tricopter with mz-12 transmitter No. 16540.RTF Copyright Graupner/SJ GmbH Index Introduction... 4 Service Centre... 4 Intended use... 5 Package content... 5 Symbols explication...
More informationBuilding the BX24-AHT
Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with
More informationAmphenol RF Connectors
Amphenol RF Connectors 007 901-9601 SMA PLUGS & ANGLE PLUGS FOR FLEXIBLE CABLE 50X IMPEDANCE Conn. Attachment RG-/U Outer Inner 901-9511-12SF Dbl. Braid RG-316 Plug Br. Solder $17.49 901-9531-12SF Angle
More informationLED-Strip C12 MK2.6. Product Sheet
LED-Strip C12 MK2.6 Product Sheet schnick-schnack-systems Introduction features Generation 3 compatible Automatic Addressing System (Smart-Link) no addressing at the board Compatible with other series
More informationUltra Small Surface Mount Coaxial Connectors 1.4mm Mated Height
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
More informationUltra-Small Surface Mount Coaxial Connectors mm Mated Height
All non- products have been discontinued, or will be discontinued soon. the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative. NEW Ultra-Small
More informationLED-Strip C25 MK2.6. Product Sheet
LED-Strip C25 MK2.6 Product Sheet schnick-schnack-systems Introduction features Generation 3 compatible Automatic Addressing System (Smart Link) no addressing at the board Compatible with other series
More informationTube Cricket Build Guide
Tube Cricket Build Guide The Tube Cricket is a small-wattage amp that puts out about 1 watt of audio power. With a 12AU7 tube-preamp and a JRC386 power amp, the Tube Cricket gives you great tone in a compact
More informationMyFlyDream TeleFlyPro V1.04
MyFlyDream TeleFlyPro V1.04 www.myflydream.com Notes Thank you for purchasing the MyFlyDream TeleFlyPro (hereinafter referred to as TFPro). Please follow this manual to get familiar with the TFPro and
More information8D with High Frequency Coaxial Contact
8D Series M Coaxial Contacts 8D with High Frequency Coaxial Contact robust and powerfull coaxial High Frequency transmission (M) now available in any size 8 SOURIU insert of D38999 Series III. Spring HF
More informationStainless Steel SMA Connectors Product Catalog
Stainless Steel SMA Connectors Product Catalog Connectivity...for Stainless Steel SMA Connectors Connectivity...for Johnson Stainless Steel SMA Connectors meet or exceed the performance requirements of
More informationMX-VGA CABLE MX-2107 AND MX MDR Electronics
MX-VGA CABLE MX-2107 AND MX-2108 MDR Electronics www.mdrelectronics.com Table of contents 1. Introduction 3 2. Image 4 3. Features 6 4. Specifications 7 5. Warranty 8 http://www.mdrelectronics.com/ at
More informationNational Wire and Cable and National Cable Molding Headquarters Los Angeles California
National Wire and Cable and National Cable Molding Headquarters Los Angeles California CAPABILITIES Medical Business Machines Communications Equipment Computer Equipment Audio Systems General Instrumentation
More informationBTT rev. a Bob s TechTalk #8
BTT rev. a Bob s TechTalk #8 Bob s TechTalk #8 by Bob Eckweiler, AF6C Coaxial Connectors: (Part I of III) UHF and N Connectors and MMCX/MCX Series. There are many other connectors that are less common
More informationMX-MOLDED READY VGA TO BNC CABLES MX-2076 MX MDR Electronics
MX-MOLDED READY VGA TO BNC CABLES MX-2076 MX-2077 MDR Electronics www.mdrelectronics.com Table of contents 1. Introduction 3 2. Image 4 3. Features 6 4. Specifications 7 5. Warranty 8 http://www.mdrelectronics.com/
More informationAPPLIANCES /// MTA, CST-100 II AND SL-156 CONNECTORS. CONNECTORS/ APPLIANCES MTA, CST-100 II and SL-156 Connectors
PPLINCES /// MT, CST-100 II ND SL-156 CONNECTORS CONNECTORS/ PPLINCES MT, CST-100 II and SL-156 Connectors Contents Introduction This catalog has been designed to assist you, our customer, identify products
More informationLED-Strip C50 MK2.6. Product Sheet
LED-Strip C50 MK2.6 Product Sheet schnick-schnack-systems Introduction features Generation 3 compatible Automatic Addressing System (Smart Link) no addressing at the board Compatible with other series
More informationRibbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
More informationRibbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with MIL standard, and used for wide
More informationRibbon Cable connector Compliant with MIL Standard
Ribbon Cable connector Compliant with MIL Standard HIF3B Series Product Specifications Rating Features 1. Product Compliant with MIL Standard HIF3B series has been developed as a product compliant with
More information