Calibrating the timecode signal input
|
|
- Erin Young
- 6 years ago
- Views:
Transcription
1 Chapter 5 Calibrating the timecode signal input Computer hardware can introduce an offset between the timecode signal and the video signal, which causes the timecode and video to be offset when they are captured. If the timecode you capture doesn t match the timecode on your video deck, you ll need to set a timecode offset. To do this, you ll need a test tape with timecode visible in the frame (a window dub), or you ll need a deck or camcorder with a timecode display option. To calibrate timecode: 1. Capture video from the window dub test tape or from another tape with the timecode display option for your deck turned on (Figure 5a.1). 2. In the first frame of your test capture clip, compare the burned-in timecode visible in the video frame with the timecode value that appears in the Viewer s Current Timecode field (Figure 5a.2). (If you use the display option, the number will appear in your camera s viewfinder or on your external monitor.) 3. Calculate the duration of the offset by subtracting the Current Timecode field s value from the burned-in timecode value (Figure 5a.3). If the timecode value in the Current Timecode field is less than the burned-in timecode value, you should get a positive number for the offset duration. If the Current Timecode field s value is greater than the burned-in timecode value, you should get a negative number. Figure 5a.1 Capture a test clip. Figure 5a.2 Compare the burned-in timecode visible in the video frame with the timecode value in the Viewer s Current Timecode field. Figure 5a.3 The burned-in timecode minus the Current Timecode value equals the duration of the offset. 5-1
2 Capturing Video 4. You ll need to edit your Device Control preset to enter the timecode offset. Choose Edit > Audio/Video Settings; then click the Device Control Presets tab. 5. On the Device Control Presets tab, select your current Capture preset (it should be checked); then click Edit. 6. In the Device Control Preset Editor window, enter the calculated duration of the offset in the Capture Offset field; then click OK (Figure 5a.4). 7. Repeat the test to double-check your work. Tip You should recheck your timecode calibration every time you switch video decks or cables! If you regularly switch between a couple of decks, you can incorporate each deck s timecode offset into a customized Easy Setup. Simply switch Easy Setups when you switch decks. It s that simple. Figure 5a.4 In the Device Control Preset Editor window, enter the calculated duration of the offset in the Capture Offset field. 5-2
3 Chapter 5 Calibrating capture settings with color bars and audio tone When you capture video that is already in a digital format (such as DV), FCP makes a straight digital-to-digital transfer, so you won t be able to adjust color and brightness on digital video in the log and capture process. That s why the adjustment sliders on the Clip Settings tab are disabled when a DV Capture preset is selected. Once your material has been captured, however, you can use FCP s excellent color correction filters to tweak the image to your (or your client s) satisfaction. See Using Color Correction Filters in Chapter 16 for more information. If you are capturing video from an analog video format or using an analog-to-digital capture card with FCP, your setup procedure should include the calibration of your capture settings using color bars and an audio tone from your source videotape. Calibrating a tape to color bars and an audio tone matches the color and audio level settings for a whole tape to the settings present when that tape was recorded. The settings you make are saved with each logged clip and applied when you capture the clip. FCP Protocol: Luminance Measurement Analog vs. Digital Avideo image s luminance (brightness) is measured differently in the analog video domain, where it s measured in IRE units, and in Final Cut Pro s digital domain, which is governed by the International Telecommunications Union (ITU) standard for digital video. When you use FCP s waveform monitor and vectorscope to examine your analog video s luminance levels, keep in mind that the FCP waveform displays the luminance level as a percentage; it does not display luminance levels in the analog video scale of IRE units. Your analog capture device will determine the black IRE level of its output (a switch on the device should allow you to select a black level of 7.5 IRE or 0 IRE). Whether your analog video input is set to output a black level of 7.5 IRE or 0 IRE, black is always represented on FCP s digital waveform scale as 0 percent, and white is represented as 100 percent. (That s percentage not IRE units.) When it s time to output your video to an analog video device, the IRE settings of the analog video device that s converting your digital video back to analog will control the final IRE black level. Confusing? You bet. If your analog video levels are critical to your project, you ll need to monitor them after they ve been converted to analog with an external hardware waveform monitor inserted at the analog output of your video device or capture card. There is much more to be learned about analog-to-digital video capture. See page III-535 of Apple s Final Cut Pro User Manual PDF, and take a look at Final Cut Pro: About Luminance (article ID 60864) at the Apple Support site: www/info.apple.com/kbnum/n
4 Capturing Video Figure 5a.5 Use the Log and Capture window s transport controls to play the color bar portion of your tape. Figure 5a.6 Click the Video Scopes button. Asingle calibration operation per tape may be enough, but if you need to, you can also use the Clip Settings tab in the Log and Capture window to customize settings for individual clips. Customized clip settings will be saved with that clip. Final Cut Pro includes a waveform monitor and a vectorscope that let you see adjustments and examine the quality of the incoming signal. You make these adjustments on the Clip Settings tab. This procedure will be easier if you record at least 30 seconds of standard color bars on each tape to use when making baseline adjustments. To adjust clip settings with bars and tone (non-dv only): 1. Choose File > Log and Capture. 2. In the Log and Capture window, use the transport controls to play the color bar portion of your tape (Figure 5a.5). The tape must be playing for the measurements in the waveform and vectorscope to be accurate. 3. Click the Clip Settings tab to open it. 4. On the Clip Settings tab, click the Video Scopes button (Figure 5a.6). The waveform monitor will be updated only while the Log and Capture window is active. continues on next page 5-4
5 Chapter 5 5. Use the Waveform Monitor and Vectorscope window (Figure 5a.7) to review and calibrate the following: Adjust the black level so that the black reference bar in the waveform monitor is at the desired level. The waveform monitor displays the luminance and chrominance values of the incoming signal. The vertical axis displays the dynamic range of the signal from black at the bottom (0 percent) to white at the top (100 percent). If black level and white level controls are not available, use the brightness and contrast controls. Adjust the white level so that the white reference bar in the waveform monitor is at the desired level (100 IRE for a 100 percent white reference bar). Adjust the hue so that the ends of the lines in the vectorscope are as near the color target boxes as possible. The diagonal line marker FT is the flesh tone target. All flesh tones should center around this line. The vectorscope displays the hue and saturation values of the incoming signal. The hue is represented by the angle of a line within the circle (its radial position). The saturation is represented by the length of the line from the circle s center point. The vectorscope displays targets for the optimal values for the six primary colors (red, green, blue, yellow, magenta, and cyan) in a standard color bar pattern. Adjust the saturation so that the ends of the lines in the vectorscope are as close as possible to the center of the target boxes. Use the transport controls to shuttle the tape to a portion with a 1 khz audio reference tone; then use the Gain slider to adjust the audio signal to 0 db or so that it does not peak into the red areas of the audio meters. 6. After you ve adjusted your settings, close the Waveform Monitor and Vectorscope window before capturing. Figure 5a.7 Use the Waveform Monitor and Vectorscope window to review and calibrate image-quality parameters. This procedure is for analog-to-digital captures only. 5-5
Crystal Sanchez Video Preservation 1 December Video Preservation Project: No Setup vs. Setup
Crystal Sanchez Video Preservation 1 December 2011 Video Preservation Project: No Setup vs. Setup When doing transfers of analog video materials, there are a variety of choices available to the preservation
More informationColor Correction in Final Cut Studio Introduction to Color
Color Correction in Final Cut Studio Introduction to Color Part 1: Getting Started with Color Part 2: Managing and Applying Grades upart 3: Using the Scopes and Auto Balanceo Part 4: Copying from One Clip
More informationClick on the chapter below to navigate to the corresponding section of this document.
The following are delivery specifications for PANDA 23 both physical and digital. Regardless of delivery method the following specifications must be adhered to in order to run programming on PANDA 23.
More informationIntroduction 2. The Veescope Live Interface 3. Trouble Shooting Veescope Live 10
Introduction 2 The Veescope Live Interface 3 Inputs Tab View 3 Record/Display Tab View 4 Patterns Tab View 6 Zebras Sub Tab View 6 Chroma Key Sub View 6 Scopes Tab View 8 Trouble Shooting Veescope Live
More informationTo show the Video Scopes, click on the down arrow next to View located in the upper- right corner of your playback panel.
1 FCPX: 3.3 COLOR CORRECTION Color Correcting and Color Grading are usually the last things you do before exporting your video. Color Correcting is the process of achieving the correct, natural color of
More informationDesigning Custom DVD Menus: Part I By Craig Elliott Hanna Manager, The Authoring House at Disc Makers
Designing Custom DVD Menus: Part I By Craig Elliott Hanna Manager, The Authoring House at Disc Makers DVD authoring software makes it easy to create and design template-based DVD menus. But many of those
More informationInstaller Guide. Follow these instructions to set up the PowerLite Pro Cinema 1080 projector and HQV video processor.
Installer Guide Follow these instructions to set up the PowerLite Pro Cinema 1080 projector and HQV video processor. For more information, see the manuals that came with these products. Setting Up the
More informationsdiscope Signal Analysis Software Version 6
sdiscope Signal Analysis Software Version 6 Table of Contents About sdiscope...3 Reference...5 Main Interface Overview...5 Settings Window...11 Data View...16 Picture...17 Vectorscope...19 Vectorscope
More informationSony AV /2 EIAJ Color Deck
, Archive-Ready Sony AV-8650 1/2 EIAJ Color Deck Now Available: Serial 12168 This is a cream puff Cadillac of an EIAJ Color deck. ZinFurbisher Ken Zin says in his experience, you'd be "unlikely to find
More informationMultiScopeLite. Users Guide. Video Measurement and Calibration Tools. RHMG Software Tools Library 1/18/2013. Bill and Scott Werba
MultiScopeLite Video Measurement and Calibration Tools Users Guide RHMG Software Tools Library 1/18/2013 Authors: Bill and Scott Werba Developer: Scott Werba Document ID: 3000-001 Revision: v1.0.4 Publication
More information4KScope Software Waveform, Vectorscope, Histogram and Monitor
4KScope - a 4K/2K/HD/SD Video Measurement Tool View your color bars, test patterns, live camera or telecine signal for device or facility installation, setup, commissioning/certification and other operational
More informationDIGITAL PERSONAL STUDIO Version 1.30 Addendum
DIGITAL PERSONAL STUDIO Version 1.30 Addendum Contents V1.30 FEATURES...1 AK.SYS TRACKVIEW...2 INSTALLING AK.SYS TRACKVIEW...2 USING AK.SYS TRACKVIEW...3 METERS...4 IN / OUT TIMES...5 TIMECODE DISPLAY...5
More informationProcessing. Electrical Engineering, Department. IIT Kanpur. NPTEL Online - IIT Kanpur
NPTEL Online - IIT Kanpur Course Name Department Instructor : Digital Video Signal Processing Electrical Engineering, : IIT Kanpur : Prof. Sumana Gupta file:///d /...e%20(ganesh%20rana)/my%20course_ganesh%20rana/prof.%20sumana%20gupta/final%20dvsp/lecture1/main.htm[12/31/2015
More information4kScope Signal Analysis Software Version 6
4kScope Signal Analysis Software Version 6 Table of Contents About 4kScope...4 Reference...5 Main Interface Overview...5 Settings Window...7 Data View...13 Picture...14 Vectorscope...16 Vectorscope Setup...16
More informationE X P E R I M E N T 1
E X P E R I M E N T 1 Getting to Know Data Studio Produced by the Physics Staff at Collin College Copyright Collin College Physics Department. All Rights Reserved. University Physics, Exp 1: Getting to
More informationCompany Software Manual version Issued Date Sony Corporation Projector Calibration Pro Version 0.04 Mar 3rd, 2017
1 A. Equipment Required B. Corresponding projectors / Functions C. Preparation D. Functions E. Note 1. Equipment Required - Software: Projector Calibration Pro - Sony Projector with LAN port
More informationNetwork Video Analyzer. Signal Analysis Software Version 6
Network Video Analyzer Signal Analysis Software Version 6 Table of Contents About Network Video Analyzer...3 Reference...5 Main Interface Overview...5 IP Setup Window...12 Settings Window...14 Data View...20
More informationStandard Definition. Commercial File Delivery. Technical Specifications
Standard Definition Commercial File Delivery Technical Specifications (NTSC) May 2015 This document provides technical specifications for those producing standard definition interstitial content (commercial
More informationHigh-Definition, Standard-Definition Compatible Color Bar Signal
Page 1 of 16 pages. January 21, 2002 PROPOSED RP 219 SMPTE RECOMMENDED PRACTICE For Television High-Definition, Standard-Definition Compatible Color Bar Signal 1. Scope This document specifies a color
More informationARRI Look Creator. Quick Guide / Release Notes for Open Beta Test v1.0
ARRI Look Creator Quick Guide / Release Notes for Open Beta Test v1.0 Introduction Starting with ALEXA Software Update Packet (SUP) 4.0, ARRI ALEXA cameras can apply userdefined looks to customize the
More informationSetup Guide. Color Volume Analysis Workflow. Rev. 1.2
Setup Guide Color Volume Analysis Workflow Rev. 1.2 Introduction Until the introduction of HDR, a video display s color reproduction range was typically represented with a two-dimensional chromaticity
More informationAX20. Atlas 19.5" 3G-SDI/HDMI Field and Studio Monitor with 3D LUTs & Scopes. Quick Start Guide. What s Included CHECKED BY
AX20 Quick Start Guide Atlas 19.5" 3G-SDI/HDMI Field and Studio Monitor with 3D LUTs & Scopes What s Included 1 x Atlas 19.5" Monitor 1 x AC Adapter 1 x Sunhood CHECKED BY AX20 FRONT 1920 x 1080 19.5 inch
More informationAMIRA & ALEXA Mini Color by Numbers
AMIRA & ALEXA Mini Color by Numbers WHITE PAPER Date: 3 rd May 2018 Introduction This document gives an insight into the color processing of AMIRA/ALEXA Mini and describes the creative options available.
More informationUltra TQ V3.4 Update 4KTQ Ultra TQ Update 1
Ultra TQ Ultra TQ Update 1 About this Document Notice This documentation contains proprietary information of Omnitek. No part of this documentation may be reproduced, stored in a retrieval system or transmitted
More information2018 Teradek, LLC. All Rights Reserved. REFERENCE GUIDE
2018 Teradek, LLC. All Rights Reserved. REFERENCE GUIDE TABLE OF CONTENTS 1. INTRODUCTION... 3 Support Resources... 3 Disclaimer... 3 User Interface... 3 2. GETTING STARTED... 5 Configure a Camera Source...
More informationAchieve Accurate Critical Display Performance With Professional and Consumer Level Displays
Achieve Accurate Critical Display Performance With Professional and Consumer Level Displays Display Accuracy to Industry Standards Reference quality monitors are able to very accurately reproduce video,
More informationSpearhead Display. How To Guide
Spearhead Display The Tektronix color tool set has always been about allowing the user to marry the Art & Science irrespective of the color space they are working in. How To Guide How To Guide Figure 1.
More informationUsing the VP300 to Adjust Video Display User Controls
Using the VP300 to Adjust Video Display User Controls Today's technology has produced extraordinary improvements in video picture quality, making it possible to have Cinema-like quality video right in
More informationChannel calculation with a Calculation Project
03/17 Using channel calculation The Calculation Project allows you to perform not only statistical evaluations, but also channel-related operations, such as automated post-processing of analysis results.
More informationManual Version V1.02
Pixie-FS Time Base Corrector Manual Version V1.02 BURST ELECTRONICS INC ALBUQUERQUE, NM 87109 USA (505) 898-1455 VOICE (505) 890-8926 Tech Support Made in USA (505) 898-0159 FAX www.burstelectronics.com
More informationSX7. Saga 7" Super Bright HDMI/3G-SDI Field Monitor with 3D-LUTs. Quick Start Guide. What s Included CHECKED BY
SX7 Quick Start Guide Saga 7" Super Bright HDMI/3G-SDI Field Monitor with 3D-LUTs What s Included 1 x Saga X7 Monitor 1 x V-Mount Plate (Attached) 1 x Mini-XLR to P-TAP Cable 1 x Dual Sony L Battery Adapter
More informationWhat s New in Raven May 2006 This document briefly summarizes the new features that have been added to Raven since the release of Raven
What s New in Raven 1.3 16 May 2006 This document briefly summarizes the new features that have been added to Raven since the release of Raven 1.2.1. Extensible multi-channel audio input device support
More informationContents. Welcome to LCAST. System Requirements. Compatibility. Installation and Authorization. Loudness Metering. True-Peak Metering
LCAST User Manual Contents Welcome to LCAST System Requirements Compatibility Installation and Authorization Loudness Metering True-Peak Metering LCAST User Interface Your First Loudness Measurement Presets
More informationADJUSTABLE RANGE OF PARAMETERS [End of the Book]
Page Introduction FEATURE OF AG-HPX250 S BUILT-IN SENSOR 2 Chapter 1. SCENE FILE 4 Chapter 2. DETAIL / V DETAIL 6 Chapter 3. KNEE 8 Chapter 4. GAMMA 10 Chapter 5. DRS 12 Chapter 6. DETAIL CORING /SKIN
More informationAbout Final Cut Pro Includes installation instructions and information on new features
apple About Final Cut Pro 1.2.5 Includes installation instructions and information on new features This document includes installation instructions and describes features and enhancements of Final Cut
More informationWVR500 Waveform/Vector Monitor
Service Manual WVR500 Waveform/Vector Monitor 070-8897-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are
More informationCalibration Best Practices
Calibration Best Practices for Manufacturers By Tom Schulte SpectraCal, Inc. 17544 Midvale Avenue N., Suite 100 Shoreline, WA 98133 (206) 420-7514 info@spectracal.com http://studio.spectracal.com Calibration
More informationScopeBox 2.0. A Whole New Box of Tricks
ScopeBox 2.0 A Whole New Box of Tricks ScopeBox 2.0 copyright 2008 divergent media, inc. All rights reserved. iii Table of Contents Contents 1 Welcome to ScopeBox 2.0 1 Welcome. 1 What s new in 2.0. 1
More information9" Portable On-camera LCD Monitor. User Manual. Model: DT-X91F HDSDI&HDMI, Waveform, Audio meter, Focus assist DT-X91H 3GSDI&HDMI DT-X91C HDMI
9" Portable On-camera LCD Monitor User Manual Model: DT-X91F HDSDI&HDMI, Waveform, Audio meter, Focus assist DT-X91H DT-X91C 3GSDI&HDMI HDMI Please read this User Manual throughout before using. Preface
More informationUser Manual. 7" Portable On-camera LCD Monitor DT-X71H DT-X71C. Model: DT-X71F HDSDI&HDMI, Waveform, Audio meter, Focus assist HDSDI&HDMI HDMI
7" Portable On-camera LCD Monitor User Manual Model: DT-X71F HDSDI&HDMI, Waveform, Audio meter, Focus assist DT-X71H DT-X71C HDSDI&HDMI HDMI Please read this User Manual throughout before using. Preface
More informationCLIPSTER. 3D LUT File Generation with the Kodak Display Manager. Supplement
Supplement: CLIPSTER 3D LUT File Generation with the Kodak Display Manager (Version 1.0) CLIPSTER 3D LUT File Generation with the Kodak Display Manager Supplement Supplement for the CLIPSTER Documentation:
More informationUSING SCOPES AS CREATIVE TOOLS
3 USING SCOPES AS CREATIVE TOOLS The next two important tools after the video monitor itself in analyzing a video image are a waveform monitor and vectorscope. There are three general categories of scopes
More informationIndustrial Technology
2011 HIGHER SCHOOL CERTIFICATE EXAMINATION Industrial Technology Multimedia Technologies Total marks 40 General Instructions Reading time 5 minutes Working time 1 1 hours 2 Write using black or blue pen
More informationGRATICAL EVF. Bright. Sharp. Brilliant. The Gratical HD/LT Micro-OLED Electronic Viewfinder User Manual.
Bright. Sharp. Brilliant The Gratical HD/LT Micro-OLED Electronic Viewfinder User Manual www.zacuto.com Table of Contents Gratical Features...3-4 Included Components...3 Battery Usage...5 Power Sources...5
More informationStandard Operating Procedure of nanoir2-s
Standard Operating Procedure of nanoir2-s The Anasys nanoir2 system is the AFM-based nanoscale infrared (IR) spectrometer, which has a patented technique based on photothermal induced resonance (PTIR),
More informationBright. Sharp. Brilliant.
Bright. Sharp. Brilliant. The Gratical HD Micro-OLED Electronic Viewfinder Full Digital Manual Table of Contents Gratical Features...3 Included Components...4 Battery Usage...4 Power Sources...4 HDSDI
More informationMedia Delivery Technical Specifications for VMN US Network Operations
Media Delivery Technical Specifications for VMN US Network Operations October 19, 2016 VIACOM MEDIA NETWORKS US NETWORK OPERATIONS CENTER 35 ADAMS AVENUE HAUPPAUGE, NY 11788 TABLE OF CONTENTS 1.0 Standard
More informationAMIQ-K2 Program for Transferring Various-Format I/Q Data to AMIQ. Products: AMIQ, SMIQ
Products: AMIQ, SMIQ AMIQ-K2 Program for Transferring Various-Format I/Q Data to AMIQ The software AMIQ-K2 enables you to read, convert, and transfer various-format I/Q data files to AMIQ format. AMIQ-K2
More informationGetting Started. Connect green audio output of SpikerBox/SpikerShield using green cable to your headphones input on iphone/ipad.
Getting Started First thing you should do is to connect your iphone or ipad to SpikerBox with a green smartphone cable. Green cable comes with designators on each end of the cable ( Smartphone and SpikerBox
More informationUser Manual VM700T Video Measurement Set Option 30 Component Measurements
User Manual VM700T Video Measurement Set Option 30 Component Measurements 070-9654-01 Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - FAX 781.665.0780 - TestEquipmentDepot.com
More informationPanasonic Broadcast. AW-E860N Menu Information
Panasonic Broadcast AW-E860N Menu Information Adjustment $ Total pedestal level adjustment (Use an oscilloscope or a waveform monitor for this adjustment.) This step is to adjust the black levels (pedestal
More informationMike Robin MIKE ROBIN S COLUMN SEPTEMBER Introduction. Generation of a color bars signal
MIKE OIN S COLUMN SEPTEME 1999 Mike obin, a 2-year veteran of the Canadian roadcasting Corporation Engineering Headquarters, is an independent broadcast consultant located in Montreal, Canada. He is the
More informationEBU Digital AV Sync and Operational Test Pattern
www.lynx-technik.com EBU Digital AV Sync and Operational Test Pattern Date: Feb 2008 Revision : 1.3 Disclaimer. This pattern is not standardized or recognized by the EBU. This derivative has been developed
More informationOperating Instructions
Broadcast A/V Division Model No. M-LYNX-702W Dual 7 High Resolution Rack Mount Display with Waveform Operating Instructions V.1.0 Table of Contents 1. PRODUCT DESCRIPTION... 3 2. MENU SETTING... 6 3. SPECIFICATIONS...
More informationVHR 16 User s Manual
VHR 16 User s Manual 2007 VHR 1.11 VHR 16 overview Camera Controls : page 3 LCD Screen page 5 Direct access control panel Video Gain page 6 Color temperature page 7 Auto White Balance page 8 VHR display
More informationTSG 90 PATHFINDER NTSC Signal Generator
Service Manual TSG 90 PATHFINDER NTSC Signal Generator 070-8706-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless
More informationCh. 1: Audio/Image/Video Fundamentals Multimedia Systems. School of Electrical Engineering and Computer Science Oregon State University
Ch. 1: Audio/Image/Video Fundamentals Multimedia Systems Prof. Ben Lee School of Electrical Engineering and Computer Science Oregon State University Outline Computer Representation of Audio Quantization
More informationUSO RESTRITO. Cinema Tools 3 User Manual
Cinema Tools 3 User Manual Apple Computer, Inc. 2005 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent
More information2013, 2014 Hewlett-Packard Development Company, L.P.
User Guide 2013, 2014 Hewlett-Packard Development Company, L.P. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
More informationPalette Master Color Management Software
Palette Master Color Management Software How to Use Guide 01 Proprietary Calibration Software Co-developed with leading color calibration experts X-Rite, Palette Master software simplifies calibration
More informationApplication Note AN-708 Vibration Measurements with the Vibration Synchronization Module
Application Note AN-708 Vibration Measurements with the Vibration Synchronization Module Introduction The vibration module allows complete analysis of cyclical events using low-speed cameras. This is accomplished
More informationimso-104 Manual Revised August 5, 2011
imso-104 Manual Revised August 5, 2011 Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel
More informationADAT DC Coupling Modifications for Laser Graphic Recording
Technical Committee ADAT DC Coupling Modifications for Laser Graphic Recording Introduction... 1 ADAT PCB Modifications... 2 Additional ADAT Information... 3 Footnotes... 6 Revision 002, October 1995 ADAT
More informationENGINEERING COMMITTEE
ENGINEERING COMMITTEE Interface Practices Subcommittee SCTE STANDARD SCTE 45 2017 Test Method for Group Delay NOTICE The Society of Cable Telecommunications Engineers (SCTE) Standards and Operational Practices
More informationActivity P27: Speed of Sound in Air (Sound Sensor)
Activity P27: Speed of Sound in Air (Sound Sensor) Concept DataStudio ScienceWorkshop (Mac) ScienceWorkshop (Win) Speed of sound P27 Speed of Sound 1.DS (See end of activity) (See end of activity) Equipment
More informationRECOMMENDATION ITU-R BT (Questions ITU-R 25/11, ITU-R 60/11 and ITU-R 61/11)
Rec. ITU-R BT.61-4 1 SECTION 11B: DIGITAL TELEVISION RECOMMENDATION ITU-R BT.61-4 Rec. ITU-R BT.61-4 ENCODING PARAMETERS OF DIGITAL TELEVISION FOR STUDIOS (Questions ITU-R 25/11, ITU-R 6/11 and ITU-R 61/11)
More informationPreventing Illegal Colors
Test Equipment Depot - 800.517.8431-99 Washington Street Melrose, MA 02176 - TestEquipmentDepot.com Preventing Illegal Colors Application Note Color gamut compliance is important to ensure faithful reproduction
More informationTraditionally video signals have been transmitted along cables in the form of lower energy electrical impulses. As new technologies emerge we are
2 Traditionally video signals have been transmitted along cables in the form of lower energy electrical impulses. As new technologies emerge we are seeing the development of new connection methods within
More informationWorking with a Tektronix TDS 3012B Oscilloscope EE 310: ELECTRONIC CIRCUIT DESIGN I
Working with a Tektronix TDS 3012B Oscilloscope EE 310: ELECTRONIC CIRCUIT DESIGN I Prepared by: Kyle Botteon Questions? kyle.botteon@psu.edu 2 Background Information Recall that oscilloscopes (scopes)
More informationEventide Inc. One Alsan Way Little Ferry, NJ
Copyright 2015, Eventide Inc. P/N: 141257, Rev 2 Eventide is a registered trademark of Eventide Inc. AAX and Pro Tools are trademarks of Avid Technology. Names and logos are used with permission. Audio
More informationRemote Director. Apple 23 LCD Display. Collaborative Soft Proofing using the I. MANUFACTURER INTRODUCTION. SWOP Application Data Sheet
SWOP Application Data Sheet Remote Director Collaborative Soft Proofing using the Apple 23 LCD Display The SWOP Review Committee has approved the use of off-press proofs as input material to publications.
More informationAFM1 Imaging Operation Procedure (Tapping Mode or Contact Mode)
AFM1 Imaging Operation Procedure (Tapping Mode or Contact Mode) 1. Log into the Log Usage system on the SMIF web site 2. Open Nanoscope 6.14r1 software by double clicking on the Nanoscope 6.14r1 desktop
More informationCOMPOSITE VIDEO LUMINANCE METER MODEL VLM-40 LUMINANCE MODEL VLM-40 NTSC TECHNICAL INSTRUCTION MANUAL
COMPOSITE VIDEO METER MODEL VLM- COMPOSITE VIDEO METER MODEL VLM- NTSC TECHNICAL INSTRUCTION MANUAL VLM- NTSC TECHNICAL INSTRUCTION MANUAL INTRODUCTION EASY-TO-USE VIDEO LEVEL METER... SIMULTANEOUS DISPLAY...
More informationVGA to Video Converter ID# 424 Operation Manual
VGA to Video Converter ID# 424 Operation Manual Introduction Features The VGA to Video converter provides automatic conversion of PC desktop images to high quality video images for standard television
More informationTo fully utilize Media 100 s genlocking capability, you ll need the following equipment connected to your system:
B Genlock Setup Overview............................................. 602 Required Equipment................................ 602 Using the Genlock Setup Window....................... 603 Selecting the
More informationPrecision DeEsser Users Guide
Precision DeEsser Users Guide Metric Halo $Revision: 1670 $ Publication date $Date: 2012-05-01 13:50:00-0400 (Tue, 01 May 2012) $ Copyright 2012 Metric Halo. MH Production Bundle, ChannelStrip 3, Character,
More informationDektak Step by Step Instructions:
Dektak Step by Step Instructions: Before Using the Equipment SIGN IN THE LOG BOOK Part 1: Setup 1. Turn on the switch at the back of the dektak machine. Then start up the computer. 2. Place the sample
More informationLAB 1: Plotting a GM Plateau and Introduction to Statistical Distribution. A. Plotting a GM Plateau. This lab will have two sections, A and B.
LAB 1: Plotting a GM Plateau and Introduction to Statistical Distribution This lab will have two sections, A and B. Students are supposed to write separate lab reports on section A and B, and submit the
More informationS7H-DK S7H 7" High Bright Monitor Deluxe Kit
S7H-DK S7H 7" High Bright Monitor Deluxe Kit QUICKSTART GUIDE What s Included 1 x S7H Monitor 1 x Camera Shoe Mount 1 x Neoprene Sleeve 1 x Mini-XLR to P-TAP Cable 2 x DV Battery Plate 1 x DV Battery 1
More informationSM02. High Definition Video Encoder and Pattern Generator. User Manual
SM02 High Definition Video Encoder and Pattern Generator User Manual Revision 0.2 20 th May 2016 1 Contents Contents... 2 Tables... 2 Figures... 3 1. Introduction... 4 2. acvi Overview... 6 3. Connecting
More informationVM15 Streamer V User s Guide
VM15 Streamer V3.33.6 User s Guide Endpoint Technology, LLC 26624 Ocean View Drive Malibu CA U.S. 90265 Technical Questions Contact: Jim Ketcham jsketcham@earthlink.net Index to VM- 15 Users Guide 1. Product
More informationSignal Processing. Case Study - 3. It s Too Loud. Hardware. Sound Levels
Case Study - 3 Signal Processing Lisa Simpson: Would you guys turn that down! Homer Simpson: Sweetie, if we didn't turn it down for the cops, what chance do you have? "The Simpsons" Little Big Mom (2000)
More informationPYROPTIX TM IMAGE PROCESSING SOFTWARE
Innovative Technologies for Maximum Efficiency PYROPTIX TM IMAGE PROCESSING SOFTWARE V1.0 SOFTWARE GUIDE 2017 Enertechnix Inc. PyrOptix Image Processing Software v1.0 Section Index 1. Software Overview...
More information2017 MICHIGAN SKILLS USA CHAMPIONSHIPS TASK AND MATERIALS LIST. SKILL OR LEADERSHIP AREA: Television Video Production
2017 MICHIGAN SKILLS USA CHAMPIONSHIPS TASK AND MATERIALS LIST CONTEST LOCATION: JW Marriott 235 Louis Campau St. NW Grand Rapids, MI 49503 (616) 242-1500 http://ilovethejw.com/ SKILL OR LEADERSHIP AREA:
More informationTERMINOLOGY INDEX. DME Down Stream Keyer (DSK) Drop Shadow. A/B Roll Edit Animation Effects Anti-Alias Auto Transition
A B C A/B Roll Edit Animation Effects Anti-Alias Auto Transition B-Y Signal Background Picture Background Through Mode Black Burst Border Bus Chroma/Chrominance Chroma Key Color Bar Color Matte Component
More informationUltra 4K Tool Box. Version Release Note
Ultra 4K Tool Box Version 2.1.43.0 Release Note This document summarises the enhancements introduced in Version 2.1 of the software for the Omnitek Ultra 4K Tool Box and related products. It also details
More informationBTV Tuesday 21 November 2006
Test Review Test from last Thursday. Biggest sellers of converters are HD to composite. All of these monitors in the studio are composite.. Identify the only portion of the vertical blanking interval waveform
More informationISOMET. Compensation look-up-table (LUT) and How to Generate. Isomet: Contents:
Compensation look-up-table (LUT) and How to Generate Contents: Description Background theory Basic LUT pg 2 Creating a LUT pg 3 Using the LUT pg 7 Comment pg 9 The compensation look-up-table (LUT) contains
More informationTutorial 3 Normalize step-cycles, average waveform amplitude and the Layout program
Tutorial 3 Normalize step-cycles, average waveform amplitude and the Layout program Step cycles are defined usually by choosing a recorded ENG waveform that shows long lasting, continuos, consistently
More informationTR 038 SUBJECTIVE EVALUATION OF HYBRID LOG GAMMA (HLG) FOR HDR AND SDR DISTRIBUTION
SUBJECTIVE EVALUATION OF HYBRID LOG GAMMA (HLG) FOR HDR AND SDR DISTRIBUTION EBU TECHNICAL REPORT Geneva March 2017 Page intentionally left blank. This document is paginated for two sided printing Subjective
More informationTable of content. Table of content Introduction Concepts Hardware setup...4
Table of content Table of content... 1 Introduction... 2 1. Concepts...3 2. Hardware setup...4 2.1. ArtNet, Nodes and Switches...4 2.2. e:cue butlers...5 2.3. Computer...5 3. Installation...6 4. LED Mapper
More informationSetup Guide. EIZO Monitors. Rev. 1.4
Setup Guide EIZO Monitors Rev. 1.4 Introduction CalMAN Display Calibration Software can automatically create optimized calibration 1D or 3D LUTs for EIZO monitors equipped with a self-calibration sensor.
More informationReference Guide 2014 ZOOM CORPORATION. Copying or reprinting this manual in part or in whole without permission is prohibited.
Reference Guide 2014 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited. Introduction is a mixer application designed specifically for the. Using a
More informationInterface Practices Subcommittee SCTE STANDARD SCTE Measurement Procedure for Noise Power Ratio
Interface Practices Subcommittee SCTE STANDARD SCTE 119 2018 Measurement Procedure for Noise Power Ratio NOTICE The Society of Cable Telecommunications Engineers (SCTE) / International Society of Broadband
More informationUsing LightSpace CMS for User Created Calibration LUTs
20140130 Flanders Scientific, Inc. 6215 Shiloh Crossing Suite G Alpharetta, GA 30005 Phone: +1.678.835.4934 Fax: +1.678.804.1882 E-Mail: Support@FlandersScientific.com www.flandersscientific.com 1. If
More informationimso-104 Manual Revised July 19, 2012
imso-104 Manual Section 1 Getting Started SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 How it works 2.10 Menus 2.20 Analog Channel 2.21 On / Off 2.22
More informationUsing Low-Cost Plasma Displays As Reference Monitors. Peter Putman, CTS, ISF President, ROAM Consulting LLC Editor/Publisher, HDTVexpert.
Using Low-Cost Plasma Displays As Reference Monitors Peter Putman, CTS, ISF President, ROAM Consulting LLC Editor/Publisher, HDTVexpert.com Time to Toss The CRT Advantages: CRTs can scan multiple resolutions
More informationRevision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting
PRODUCT ADC TOPIC ODETICS TCS-2000 CART MACHINE DATE: May 14, 1999 REVISION HISTORY Revision Protocol Date Author Company Description 1.1 May 14, Seth LOUTH Revised for formatting 1999 Olitzky 1.0 Aug.
More informationDH7-DK QUICKSTART GUIDE. DH7 4K Support HDMI On-Camera Field Monitor Deluxe Kit
DH7-DK QUICKSTART GUIDE DH7 4K Support HDMI On-Camera Field Monitor Deluxe Kit What s Included 1 x DH7 Monitor 1 x AC Adapter 1 x Camera Shoe Mount 1 x Screen Cleaning Wipe 1 x Screen Protection Film 1
More informationBy Jim Norton Bird Technologies Group Applications Engineer
Introduction The masking effect of cable loss may cause your antenna to "appear" to perform more efficiently than is actually the case. In fact, it is possible to measure apparently acceptable or return
More information