15DLV77C. 15-inch Diagonal LCD TV/DVD COMBINATION SERVICE MANUAL FILE NO GR

Transcription

1 FILE NO. -GR SERVICE MANUAL -inch Diagonal LCD TV/DVD COMBINATION DLVC The above model is classified as a green product (*), as indicated by the underlined serial number. This Service Manual describes replacement parts for the green product. When repairing this green product, use the part(s) described in this manual and lead-free solder (*). For(*) and (*), see the next page. Toshiba Corporation DOCUMENT CREATED IN JAPAN, June, GREEN

2 (*) GREEN PRODUCT PROCUREMENT The EC is actively promoting the WEEE & RoHS Directives that define standards for recycling and reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use of certain Hazardous Substances. From July,, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities. In line with this, Toshiba proactively promotes Green Procurement, and seeks to purchase and use products, parts and materials that have low environmental impacts. Green procurement of parts is not only confined to manufacture. The same green parts used in manufacture must also be used as replacement parts. (*) LEAD-FREE SOLDER This product is manufactured using lead-free solder as a part of a movement within the consumer products industry at large to be environmentally responsible. Lead-free solder must be used in the servicing and repair of this product. WARNING This product is manufactured using lead free solder. DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT! The melting temperature of lead-free solder is higher than that of leaded solder by F to F ( C to C). Use of a soldering iron designed for lead-based solders to repair product made with lead-free solder may result in damage to the component and or PCB being soldered. Great care should be made to ensure high-quality soldering when servicing this product especially when soldering large components, through-hole pins, and on PCBs as the level of heat required to melt lead-free solder is high.

3 Introduction -inch * Diagonal LCD TV/DVD COMBINATION Connections Basic setup TV operation DLVC OWNER S MANUAL Basic playback 9 Advanced playback Function setup Others ColorStream is a registered trademark of Toshiba America Consumer Products, L.L.C. is a trademark of Toshiba America Consumer Products, L.L.C. JXA SH / N Printed in Thailand Toshiba Corporation Before operating the unit, please read this manual thoroughly. *Screen size is approximate. JXA(Eng).indb // ::9 Introduction CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning ash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of suf cient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIAE TO RAIN OR MOISTURE. CAUTION : TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. WARNING: Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS OWNER'S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFEREE. SHOULD THE UNIT REQUIRE MAINTENAE, CONTACT AN AUTHORIZED SERVICE LOCATION. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMAE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ELOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ELOSURE IS OPENED. DO NOT STARE INTO BEAM. NOTE TO CATV INSTALLERS This is a reminder to call the CATV system installer s attention to Article - of the NEC, which provides guidelines for proper grounding and, in particular, speci es that the cable ground shall be connected to grounding system of the building, as close to the point of cable entry as practical. For additional antenna grounding information, see item on page. ON DISPOSAL The lamp(s) inside this product contain mercury. Disposal may be regulated due to environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance ( WARNING: If you decide to wall mount this television, always use a UL Listed wall bracket appropriate for the size and weight of this television. The use of any wall bracket other than a UL Listed wall bracket appropriate for the size and weight of this television for wall mounting this television could result in serious bodily injury and/or property damage. Location of the required Marking The rating sheet and the safety caution are on the rear of the unit. CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMAE STANDARDS, CFR SUBCHAPTER J. IMPORTANT SAFEGUARDS. READ INSTRUCTIONS All the safety and operating instructions should be read before the unit is operated.. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference.. HEED WARNINGS All warnings on the unit and in the operating instructions should be adhered to.. FOLLOW INSTRUCTIONS All operating and use instructions should be followed.. CLEANING Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a soft dry cloth for cleaning the exterior cabinet only.. ATTACHMENTS The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.. WATER AND MOISTURE Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. PORTABLE CART WARNING. ACCESSORIES (symbol provided by RETAC) Do not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 9. VENTILATION Slots and openings in the cabinet back or bottom are provided for ventilation, SA and to ensure reliable operation of the unit, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to.. POWER SOURCE This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company.. GROUNDING OR POLARIZATION This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will t into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. Do not defeat the safety purpose of the grounding-type plug.. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. Introduction JXA(Eng).indb // :: JXA(Eng).indb // ::

4 Introduction IMPORTANT SAFEGUARDS. LIGHTNING To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges. However, if there is thunder or lightning now, do not touch the unit and any connected cable. This will for you not to receive the electric shock by the serge of thunder.. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.. OVERLOADING Do not overload wall outlets and extension cords, as this can result in a risk of re or electric shock.. OBJECT AND LIQUID ENTRY Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in re or electric shock. Never spill or spray any type of liquid into the unit.. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section of the National Electrical Code (NEC), ANSI/NFPA, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE ANTENNA LEAD IN WIRE (continued) 9. REPLACEMENT PARTS When replacement parts are required, be sure the service technician uses replacement parts speci ed by the manufacturer or those that have the same characteristics as the original part. Unauthorized substitutions may result in re, electric shock or other hazards.. SAFETY CHECK Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including ampli ers) that produce heat.. DISC SLOT Keep your ngers well clear of the disc slot as it is closing. It may cause serious personal injury.. CONNECTING When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.. HEADPHONES When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.. LASER BEAM Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.. DISC Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.. LCD Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur. Should the LCD panel be broken and liquid leaks out, do not inhale or swallow it. Doing so may cause poisoning. If you have got it into your mouth, wash it out and consult your doctor. If your hands or clothes have touched it, wipe them with alcohol and a cleaning cloth and then wash them well. Introduction GROUND CLAMP ELECTRIC SERVICE EQUIPMENT NEC-NATIONAL ELECTRICAL CODE S9A ANTENNA DISCHARGE UNIT (NEC SECTION -) GROUNDING CONDUCTORS (NEC SECTION -) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART, PART H). SERVICING Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to quali ed service personnel. For example: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the unit. c. If the unit has been exposed to rain or water. d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a quali ed technician to restore the unit to its normal operation. e. If the unit has been dropped or the cabinet has been damaged. f. When the unit exhibits a distinct change in performance, this indicates a need for service. JXA(Eng).indb // :: Introduction Precautions tes on discs tes on handling Do not shock the LCD panel. It may cause unit damage and malfunction. When shipping the unit, the original shipping carton and packing materials come in handy. For fully protection, repack the unit as it was originally packed at the factory. Do not use volatile liquids, such as insect spray, near the unit. Do not leave rubber or plastic products to contact the unit for prolonged period. They will leave marks on the nish. The top and rear panels of the unit may become warm after a long period of use. This is not a malfunction. When the unit is not in use, be sure to remove the disc and turn off the power. If you do not use the unit for a long period, the unit may not function properly in the future. Turn on and use the unit occasionally. tes on LCD The color LCD is manufactured using extremely high precision technology, but even so may include certain pixels that do not operate properly (that do not light, that remain lit constantly, etc.). We do our best to keep the number of these defective pixels to a minimum, but please understand that they cannot be completely eliminated even with the most advanced manufacturing technologies available today. The uorescent tube which illuminates the panel from the inside will deteriorate with use. When the LCD becomes dim, ickers, or does not illuminate, contact your dealer for replacement. The brightness of the LCD monitor differs slightly depending on the viewing angles. Adjust the angle to obtain the best viewing. (The recommended angle is 9 degrees to the monitor.) tes on locating WARNING: To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with the installation instructions. When you place this unit near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted. In this case, place the unit away from the TV, radio, or VCR. To avoid damage to this product, never place or store the unit in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration. Always place the Sturdy tie (as short as possible) TV on the oor or a sturdy, level, stable surface that can support the weight of the unit. Use a sturdy tie between the Hooks Clip Screw TV top TV s rear hook TV side Band and the rear wall, pillar, etc., to secure the TV. If you use a TV stand, x the TV by using the attached band. tes on moisture condensation Moisture condensation damages the unit. Please read the following carefully. Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit. Example of moisture Moisture condensation occurs during the following cases. When you bring the unit directly from a cold place to a warm place. When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit. In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room. When you use the unit in a humid place. Wait! condensation! tes on cleaning Optical pick-up lens Do not use the unit when moisture condensation may occur. If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur. Wall outlet Use a soft, dry cloth for cleaning. Do not use any type of solvent, such as thinner and benzine, as they may damage the surface of the unit. On handling discs Do not touch the playback side of the disc. For example, handle the disc so that it is shown in gure below. Playback side Do not attach paper or tape to discs. On cleaning discs Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean. Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc. On storing discs Do not store discs in a place subject to direct sunlight or near heat sources. Do not store discs in places subject to moisture and dust such as a bathroom or near a humidi er. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping. Structure of disc contents rmally, DVD video discs are divided into titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided into tracks. DVD video disc DVD video disc Title Title Chapter Chapter Chapter Chapter Chapter Video CD/Audio CD Video CD/Audio CD Track Track Track Track Track Each title, chapter or track is assigned a number, which is called title number, chapter number or track number respectively. There may be discs that do not have these numbers. tes on copyright The unauthorized recording, use, distribution, or revision of copyrighted materials including, without limitation, television programs, videotapes, and DVDs, is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Introduction JXA(Eng).indb // :: JXA(Eng).indb // ::

5 Introduction tes on discs (Continued) Contents About this owner s manual This owner s manual explains the basic instructions of this unit. Some DVD video discs are produced in a manner that allows speci c or limited operation during playback. As such, the unit may not respond to all operating command. This is not a defect in the unit. Refer to instruction notes of discs. The following symbol may appear on the TV screen during operation. It means that the operation is not permitted by the TV/ DVD or the disc. For example, sometimes it is unable to stop the playback of copyright message of the disc when the STOP ( ) button is pressed. Alternatively, this symbol may also indicate that the feature is not available for the disc. tes on region numbers The region number of this unit is. If region numbers, which stand for their playable area, are printed on your DVD video disc and you do not nd or ALL, disc playback will not be allowed by the player. (In this case, the unit will display a message on-screen.) Some DVDs that have no region code label may still be subject to area restrictions and therefore not playable. On Video CDs This unit supports Video CDs equipped with the PBC (Version.) function. (PBC is the abbreviation of Playback Control.) You can enjoy two playback variations depending on types of discs. Video CD not equipped with PBC function (Version.) Sound and movie can be played on this unit in the same way as a DVD. Video CD equipped with PBC function (Version.) In addition to operation of a Video CD not equipped with the PBC function, you can enjoy playback of interactive software with search function by using the menu displayed on the TV screen (Menu Playback). Some of the functions described in this owner s manual may not work with some discs. Playable discs This unit can play the following discs. Disc Maximum Disc Mark Contents Size playback time Approx. hours (single sided disc) Audio cm Approx. hours DVD + (double sided disc) video Video discs (moving Approx. minutes pictures) (single sided disc) cm Approx. minutes (double sided disc) Audio Approx. minutes cm + (single sided disc) Video Video CDs DIGITAL VIDEO (moving Approx. minutes cm pictures) (single sided disc) Approx. minutes cm Audio (single sided disc) Audio CDs Approx. minutes cm (single sided disc) Audio cm + It depends on DivX DivX Video quality (moving cm pictures) The following discs are also available. DVD-R/RW discs of DVD video format CD-R/CD-RW discs of CD-DA, Video CD, MP, WMA, JPEG or DivX format Kodak Picture CD and FUJICOLOR CD format Some of these discs may be incompatible. You cannot play discs other than those listed above. You cannot play discs of DVD-RAM, DVD-ROM, CD- ROM, Photo CD, etc., or non standardized discs even if they may be labeled as above. Some CD-R/RWs cannot be played back depending on the recording conditions. This unit uses the NTSC color system, and cannot play DVD video discs recorded in any other color system (PAL, SECAM, etc.). This unit can play an cm disc. Please do not use a disc adapter. It may cause trouble. Please do not insert any disc of an irregular shape into the unit, as it may interfere with the function of the unit. You may not be able to remove it. Please do not use after market accessories, such as a ring protector, as this may cause trouble with the operation of the unit. Because of problems and errors that can occur during the creation of DVD and CD Software and/or the manufacture of DVD and CD discs, Toshiba cannot assure that the DVD player contained in this TV will successfully play every disc bearing the DVD and CD logos. If you happen to experience any dif culty playing a DVD and/or CD disc on the DVD player contained in this TV, please contact Toshiba Customer Service. is a trademark of DVD Format/Logo Licensing Corporation. Introduction IMPORTANT SAFEGUARDS... Precautions... tes on discs... Contents... 9 Identi cation of controls... Connections Antenna connections... Cable TV connections... Connecting to optional equipment... Power source... Basic setup Setting the language... To memorize channels... TV operation TV operation... Closed captions... Picture control adjustment... Adjusting the picture mode... Selecting the color temperature... Sound control adjustment... Stereo and Second Audio Program (SAP)... Basic playback Playing a disc... 9 Advanced playback Zooming... Locating desired scene... Repeat playback... A-B Repeat playback... Program playback... Random playback... Changing angles... Title selection... DVD menu... Changing soundtrack language... Subtitles... Disc status... To turn off the PBC... MP/WMA/JPEG/DivX and Audio CD operation... Repeat and program playback using le browser... Function setup Customizing the function settings... Temporary cancel the rating level by DVD disc... Others Language code list... Troubleshooting... Reception disturbances... Speci cations... Limited Canada Warranty... 9 Introduction JXA(Eng).indb // :: JXA(Eng).indb 9 // :: Introduction Identi cation of controls See the page in for details. Top Side Adjusting the angle of the base Approx. Approx. Introduction Left Side Right Side POWER button 9 VOLUME ( ) buttons CHANNEL ( / ) buttons STOP( EJECT ( ) button SKIP ( / ) buttons ) button 9 PLAY ( ) button 9 PHONES jack AUDIO IN (L/R) /VIDEO IN (LINE IN) jacks S-VIDEO jack Disc slot You can adjust the angle of the TV-screen for forward or for backward from vertical angle. Hold the base of the TV while adjusting the angle. Front Rear Speaker Speaker Remote sensor POWER indicator COAXIAL DIGITAL AUDIO OUT jack Antenna jack VIDEO IN (LINE IN) jack DC input jack COMPONENT VIDEO IN (Y, PB, PR) (LINE IN) jacks AUDIO IN (L/R) (LINE IN) jacks JXA(Eng).indb // :: JXA(Eng).indb // ::

6 Introduction Identi cation of controls (Continued) Remote control The instructions in this manual describe the function on the remote control. See the page in for details. Inserting batteries Open the battery compartment cover in the direction of the arrow. Install two R/AAA batteries (supplied), paying attention to the polarity indicated in the battery compartment. Replace the compartment cover. Introduction EJECT button TV/DVD button 9 Direct channel selection buttons (-9) Numbered buttons (-9) RECALL button JUMP button INPUT SELECT button PLAY MODE button GAME button TOP MENU button MENU button SETUP button PLAY button 9 STOP button 9 SKIP buttons REV button FWD button SLOW buttons ANGLE button AUDIO button *DVD MENU button Use the DVD MENU button to display the menu included on many DVD video discs. To operate a menu, follow the instructions in DVD menu. POWER button SLEEP button CH RTN button ZOOM button MUTE button VOL +/- buttons CAEL button *DVD MENU button Direction buttons ( / / / ) CH +/- buttons ENTER button RETURN button PAUSE button CLOSED CAPTION button REPEAT A-B button SUBTITLE button Operation Aim the remote control at the remote sensor and press control buttons to operate. Operate the remote control within angle on either side of the remote sensor, up to a distance of approx. meters. Approx. meters Caution: Never throw batteries into a re. tes: Be sure to use AAA size batteries. Dispose of batteries in a designated disposal area. Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with applicable laws and regulations. If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with new ones. When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination. Always remove batteries from remote control if they are dead or if the remote control is not to be used for an extended period of time. This will prevent battery acid from leaking into the battery compartment. JXA(Eng).indb // :: JXA(Eng).indb // :: Connections Antenna connections If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna system. If you are using a cable TV service (CABLE), see page for Cable TV connections. Combination VHF/UHF antenna (Single ohm cable or ohm twin-lead wire) Cable TV connections This TV/DVD has an extended tuning range and can tune most cable channels without using a Cable TV converter box. Some cable companies offer premium pay channels in which the signal is scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device which is generally provided by the cable company. For subscribers to basic cable TV service Antenna jack ohm coaxial cable (not supplied) Antenna jack - ohm matching transformer (supplied) Connect the ohm cable from the combination VHF/UHF antenna to the antenna jack on the back of the TV/DVD. If your combination VHF/UHF antenna has a ohm twin-lead wire, use the - ohm matching transformer. Combination VHF/UHF antenna (Separate VHF and UHF ohm twin-lead wires) ohm coaxial cable Antenna jack For subscribers to scrambled cable TV service For basic cable service not requiring a converter/descrambler box, connect the Cable TV ohm coaxial cable directly to the Antenna jack on the back of the TV/DVD. If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the incoming ohm coaxial cable to the converter/descrambler box. Using another ohm coaxial cable, connect the output jack of the converter/descrambler box to the antenna jack on the TV/DVD. Follow the connections shown below. Set the TV/DVD to the output channel of the converter/descrambler box (usually channel or ) and use the converter/descrambler box to select channels. Connections Antenna jack Combiner (not supplied) - ohm matching transformer (supplied) Connect the UHF ohm twin-lead wire to the combiner (not supplied). Connect the VHF ohm twin-lead wire to the - ohm matching transformer. Attach the transformer to the combiner, then attach the combiner to the antenna jack on the back of the TV/DVD. Incoming ohm Cable TV Converter/ descrambler ohm cable to TV/DVD Antenna jack UHF ohm twin-lead wire (not supplied) VHF ohm twin-lead wire (not supplied) For subscribers to unscrambled basic cable TV service with scrambled premium channels Separate VHF/UHF antennas ( ohm VHF cable and ohm UHF twin-lead wires) Antenna jack Combiner (not supplied) VHF ohm (not supplied) Connect the VHF ohm cable and UHF ohm twin-lead wire to the combiner (not supplied). Attach the combiner to the antenna jack on the back of the TV/DVD. If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the use of a converter/descrambler box, you may wish to use a signal splitter and an A/B Switch box (available from the cable company or an electronics supply store). Follow the connections shown below. With the switch in the B position, you can directly tune any nonscrambled channels on your TV/DVD. With the switch in the A position, tune your TV/DVD to the output of the converter/descrambler box (usually channel or ) and use the converter/descrambler box to tune scrambled channels. Incoming ohm Cable TV Splitter Converter/ descrambler A A/B switch B ohm cable to TV/DVD Antenna jack UHF ohm twin-lead wire (not supplied) JXA(Eng).indb // :: JXA(Eng).indb // ::9

7 Connections Connecting to optional equipment You can enjoy VCR, camcorder or TV game with connection to external input. INPUT SELECT GAME To playback from the VCR, connect the VCR to the TV/DVD as shown. Select the VIDEO by pressing INPUT SELECT repeatedly. : Signal ow (red) VCR (white) You can enjoy playing a TV game on the screen by adjusting to suitable brightness for your eyes.. Connect a TV Game to the TV/DVD.. Select the GAME by pressing GAME. The GAME mode screen appears. This TV/DVD has the GAME mode function (see page ). Left side (LINE IN) (red) : Signal ow (white) Only the LINE (yellow) IN terminals can To Audio/Video OUT be used with the GAME mode. Using the audio/video inputs Press INPUT SELECT repeatedly to select the desired mode. VIDEO, VIDEO, ColorStream or TV channel will display on the screen for seconds. TV Channel VIDEO VIDEO (Rear lower left) (Left side) ColorStream te: This key will not operate in DVD mode. Connecting to a VCR To playback from the camcorder, connect the camcorder to the TV/DVD as shown. Select the VIDEO by pressing INPUT SELECT repeatedly. Left side (LINE IN) : Signal ow Camcorder (red) (white) The LINE IN (yellow) terminals can be used To Audio/Video OUT in the same way. Connecting to a TV Game To Audio/Video OUT Audio/Video cable (not supplied) (yellow) Audio/Video cable (not supplied) te: Picture might be muted for some VCR playback. This is not a malfunction of this unit. Connecting to a camcorder Audio/Video cable (not supplied) tes: To AUDIO(L/R)/VIDEO IN You can also change the TV screen to the desired mode by pressing the CH +/ buttons. The TV/DVD can also be used as a display device for many video games. However, due to the wide variety of different types of signal generated by these devices and subsequent hook-up variations required, they have not all been included in the suggested connection diagrams. You ll need to consult each component s Owner s Manual for additional information. Interactive video games that involve shooting a gun type of joystick at on-screen target may not work on this TV/DVD. VIDEO Left side (LINE IN) To AUDIO(L/R)/VIDEO IN To AUDIO(L/R)/VIDEO IN The LINE IN terminals can be used in the same way. Connecting to an optional equipment with S-video output If you connect a VCR with an S-VIDEO cable to the S-VIDEO IN jack on the left side of the TV/DVD, you must also connect the audio cables to the AUDIO IN (LINE IN) jacks on the left side of the TV/DVD. The S-VIDEO cable only carries the video signal. The audio signal is separate. Select the VIDEO by pressing INPUT SELECT repeatedly. Left side (LINE IN) (red) (white) : Signal ow Ex. VCR with S-Video To AUDIO (L/R) IN (playback) To S-VIDEO OUT To Audio (L/R) OUT Audio cable (not supplied) S-Video cable (not supplied) To S-VIDEO IN te: When the S-VIDEO cable and the standard video cable are connected at the same time, the S-video cable takes precedence. Connecting an optional equipment with ColorStream (Component video) output Your TV/DVD is capable of using ColorStream (component video). Connecting your TV/DVD to a component video compatible DVD player, such as a Toshiba DVD player with ColorStream can greatly enhance picture quality and performance. Ex. DVD player with Component video Rear lower right of the TV : Signal ow To Component Video OUT Selecting Component input mode Press INPUT SELECT repeatedly to select ColorStream mode. ColorStream To Audio OUT To AUDIO (L/R) IN Audio cable (not supplied) Component video cable (not supplied) When using the Component video cable, an Audio cable must be connected to AUDIO IN (L/R) (LINE IN) jacks. To COMPONENT (Y, PB, PR) IN The ColorStream inputs on this unit are for use with devices that output i interlaced signals and p progressive signals. This unit will not accept or display p progressive scan signals or i interlaced high-de nition signals. If you connect a highde nition set-top receiver, p progressive scan DVD player, or other similar device to the unit s ColorStream inputs, YOU MUST SWITCH THE DEVICE S OUTPUT TO i INTERLACED OR p PROGRESSIVE MODE FIRST. Failure to do this will cause a poor or no picture to display. tes: Refer to the owner s manual of the connected equipment as well. When you connect the unit to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. If you place the unit near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the unit away from the tuner and radio. Connections JXA(Eng).indb // :: JXA(Eng).indb // :: Connections Connecting to optional equipment (Continued) You can enjoy high quality dynamic sounds by connecting the TV/DVD to optional audio equipment. : Front speaker : Rear speaker : Sub woofer : Center speaker : Signal ow Connecting to an ampli er equipped with a Dolby Digital decoder Dolby Digital Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home. You can enjoy motion picture and live concert DVD video discs encoded via the Dolby Digital recording system with this dynamic realistic sound by connecting the TV/DVD to a channel ampli er equipped with a Dolby Digital decoder or Dolby Digital processor. If you have a Dolby Surround Pro Logic decoder, you will obtain the full bene t of Pro Logic from the same DVD movies that provide full.-channel Dolby Digital soundtracks, as well as from titles with the Dolby Surround mark. Ampli er equipped with a Dolby Digital decoder To COAXIAL type digital audio input coaxial cable (not supplied) Manufactured under license from Dolby Laboratories. Dolby, and the double-d symbol are trademarks of Dolby Laboratories. Dolby Surround Pro Logic You can enjoy the dynamic realistic sound of Dolby Surround Pro Logic by connecting an ampli er and speaker system (right and left front speakers, a center speaker, and one or two rear speakers). With an ampli er equipped with a Dolby Digital Connect the equipment the same way as described in Connecting to an ampli er equipped with a Dolby Digital decoder. Refer to that ampli er s owner s manual and set the ampli er so that you can enjoy Dolby Surround Pro Logic sound. With an ampli er not equipped with a Dolby Digital Connect the equipment as follows. This connection is only suitable for Video CDs and Audio CDs. Rear lower left of the TV * Ampli er equipped with a Dolby Surround Pro Logic To COAXIAL type digital audio input Connecting to an ampli er equipped with a DTS decoder * Connect one or two rear speakers. The output sound from the rear speakers will be monaural even if you connect two rear speakers. Digital Theater Systems (DTS) DTS is a high quality surround technology used in theaters and now available for home use, on DVD video discs or audio CDs. If you have a DTS decoder or processor, you can obtain the full bene t of. channel DTS encoded sound tracks on DVD video discs or audio CDs. Ampli er equipped with a DTS decoder coaxial cable (not supplied) * This section uses the following reference mark. To COAXIAL DIGITAL AUDIO OUT Rear lower left of the TV Connecting to an ampli er equipped with a Dolby Surround Pro Logic To COAXIAL DIGITAL AUDIO OUT Rear lower left of the TV Connecting to an ampli er equipped with an MPEG audio decoder MPEG sound You can enjoy motion picture and live concert DVD video discs encoded via the MPEG recording system with dynamic realistic sound by connecting an ampli er equipped with an MPEG audio decoder or MPEG audio processor. Rear lower left of the TV Ampli er equipped with an MPEG audio decoder To COAXIAL type digital To COAXIAL DIGITAL audio input AUDIO OUT coaxial cable (not supplied) Connecting to an ampli er equipped with a digital audio input channel digital stereo You can enjoy the dynamic sound of channel digital stereo by connecting an ampli er equipped with a digital audio input and speaker system (right and left front speakers). te: PCM audio is limited to DVD or CD playback. Rear lower left of the TV Ampli er equipped with a Digital audio input To COAXIAL To COAXIAL DIGITAL type digital AUDIO OUT audio input coaxial cable (not supplied) tes: DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the AC- RF input of a Dolby Digital Receiver. This input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD. Connect the COAXIAL DIGITAL AUDIO OUT jack of the TV/DVD to the COAXIAL input of a Receiver or Processor. Refer to the owner s manual of the connected equipment as well. When you connect the TV/DVD to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before making any connections. The output sound of the TV/DVD has a wide dynamic range. Be sure to adjust the receiver s volume to a moderate listening level. Otherwise, the speakers and your hearing may be damaged by a sudden high volume sound. Turn off the ampli er before you connect or disconnect the TV/DVD s power cord. If you leave the ampli er s power on, the speakers may be damaged. Connections To COAXIAL type digital audio input To COAXIAL DIGITAL AUDIO OUT coaxial cable (not supplied) DTS and DTS Digital Out are registered trademarks of DTS, Inc. 9 JXA(Eng).indb // :: JXA(Eng).indb 9 // ::

8 Connections Basic setup Power source Power connection Setting the language This TV/DVD can display the on screen language in English, Spanish or French in the TV mode. Select the language you prefer rst, then proceed with the other menu options. POWER CAEL ENTER / / / MENU Setting the language To turn on the TV/DVD, press POWER. The Power indicator on the front of the main unit will light. Basic setup To DC input jack AC V, Hz Press MENU and then press or to select SETUP. PICTURE AUDIO SETUP SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION ENGLISH CABLE ADD OFF :SELECT :ADJUST AC adapter (supplied) AC cord (supplied) Press or to select LANGUAGE, then press or to select the desired language: English (ENGLISH), Spanish (ESPAÑOL) or French (FRANÇAIS), then press ENTER. PICTURE AUDIO SETUP SETUP TO USE AC POWER. Connect the AC cord to the AC adapter.. Connect the AC adapter plug into the TV/DVD s DC input jack.. Connect the AC cord into a wall outlet. tes: Make sure to insert the plug of each cord securely. During use the AC adapter becomes warm. This is not a malfunction. WARNING: DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC ADAPTER OR POWER CORD. THIS COULD CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE. DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE. CAUTION: DO NOT USE THE AC ADAPTER IF IT IS COVERED BY A CLOTH ETC., OR PRESSED INTO A NARROW AREA. THIS RESULTS IN POOR DISSIPATION OF HEAT AND MAY CAUSE FIRE, ELECTRIC SHOCK, OR DAMAGE. WHEN THIS UNIT IS NOT USED FOR AN EXTENDED PERIOD OF TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF SAFETY, BE SURE TO UNPLUG IT FROM THE WALL OUTLET. DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRIC SHOCK. IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED AC ADAPTER AND AC CORD MUST BE USED. CONTACT THE DEALER THAT YOU PURCHASED THE UNIT FROM. Press CAEL to clear the menu screen. CAEL LANGUAGE ENGLISH ENGLISH/FRANÇAIS/ESPAÑOL TV/CABLE CABLE CH PROGRAM ADD/ERASE ADD CLOSED CAPTION OFF :SELECT :ADJUST tes: If the unit does not operate properly, or key operation (by the unit and/or the remote control): Static electricity, etc., may affect the TV/DVD s operation. In such case, disconnect the AC cord once, then connect it again. The TV section has its own menu and also DVD section has its own menu. JXA(Eng).indb // :: JXA(Eng).indb // :: Basic setup TV operation To memorize channels This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the TV/DVD s memory. In addition to normal VHF and UHF channels, this TV/DVD can receive up to Cable TV channels. To use this TV/DVD with an antenna, set the TV/CABLE selection to the TV position. When shipped from the factory, this selection is in the CABLE position. 9 CAEL / / / CH +/ MENU TV operation POWER 9 VOL +/ TV/CABLE selection Automatic memory tuning TV operation Press MENU in the TV mode, then press or to select SETUP. SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION :SELECT Press or to select TV/CABLE. TV - VHF/UHF channels CABLE - Cable TV channels PICTURE AUDIO SETUP SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION :SELECT ENGLISH CABLE ADD OFF PICTURE AUDIO SETUP :ADJUST ENGLISH TV/CABLE ADD OFF :ADJUST Press or to select TV or CABLE. PICTURE AUDIO SETUP SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION :SELECT ENGLISH TV/CABLE ADD OFF :ADJUST Press CAEL to clear the menu screen. CAEL Cable TV chart The chart below is typical of many cable system channel allocations. Press MENU, then press or to select SETUP. Press or to select the CH PROGRAM, then press. The TV will begin memorizing all the channels available in your area. PICTURE AUDIO SETUP SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION :SELECT To ADD/ERASE channels ENGLISH CABLE ADD OFF :ADJUST Select the desired channel to be added or deleted using Direct channel selection ( 9) or CH +/. Press MENU, then press or to select SETUP. Press or to select ADD/ERASE. PICTURE AUDIO SETUP SETUP LANGUAGE TV/CABLE CH PROGRAM ADD/ERASE CLOSED CAPTION :SELECT ENGLISH CABLE ADD/ERASE OFF :ADJUST Press or to select ADD or ERASE. Press CAEL to clear the menu screen. Repeat steps ~ to add or erase other channel. CAEL To turn on the TV/DVD, press POWER. The Power indicator on the front of the main unit will light. Adjust the volume level by pressing VOL + or. The volume level will be indicated on the screen by white bars. As the volume level increases, so do the number of bars. If the volume decreases, the number of white bars also decreases. VOLUME Set the TV/CABLE selection to the appropriate position. TV - VHF/UHF channels CABLE - Cable TV channels Auto power off If a station being viewed stops broadcasting, the TV will automatically shut itself off after minutes. Press direct channel selection ( 9) to select the channel. TV mode direct channel selection When the TV/CABLE selection is in the TV position, all channels can be instantly selected by using two buttons. (for example, to select channel, press, then. If you press only, channel selection will be delayed for a few seconds.) For channels and above, press the ANT digits in order. CABLE mode direct channel selection When the TV/CABLE selection is in the CABLE position, channels can be selected as follows: TO SELECT CABLE TV CHANNELS: -9: Press twice, then -9 as needed. Example, to select channel, press. -: Press, then the remaining digits. Example, to select channel, press. -99: Press the digits in order. Example, to select channel, press. -: Press the digits in order. Example, to select channel, press. NOTE FOR CHANNELS -: If only or buttons are pressed, the corresponding channel will be selected in seconds. TV CATV VHF VHF - - UHF STD/HRC/IRC -9 - (A) (W) -9 (AA) (WW) - (AAA) (ZZZ) -9 () (9) 9-99 (A-) (A-) - () () (A) te: If a channel with no broadcast is selected, the sound will automatically be muted. TV operation JXA(Eng).indb // :: JXA(Eng).indb // ::

9 TV operation TV operation (Continued) SLEEP RECALL CH RTN MUTE VOL +/ GAME CH +/ Closed captions WHAT IS CLOSED CAPTIONING? This television has the capability to decode and display closed captioned television programs. Closed captioning will display text on the screen for hearing impaired viewers or it will translate and display text in another language. CLOSED CAPTION TV operation Closed captions CHANNEL UP/DOWN Press and release CH + or. The channel automatically stops at the next channel set into memory. For proper operation, before selecting channels, they should be set into the memory. See page To memorize channels. ANT RECALL Press RECALL to display the current informations on the screen. Press RECALL again to clear the display. Channel number or external input mode Stereo or SAP (Second Audio Program) audio status STEREO SAP ANT TV CH RETURN This button allows you to go back to the last channel selected by pressing CH RTN. Press CH RTN again to return to the last channel you were watching. ANT MUTE Press MUTE to switch off the sound. The TV/DVD s sound will be silenced and MUTE will appear brie y on the screen. The sound can be switched back on by pressing this button again or one of VOL +/. SLEEP To set the TV/DVD to turn off after a preset amount of time, press SLEEP on the remote control. The clock will count up minutes for each press of SLEEP (hm, hm,... hm, hm). After the sleep time is programmed, the display will appear brie y every ten minutes to remind you that the sleep timer is operating. To con rm the sleep timer setting, press SLEEP and the remaining time will be displayed for a few seconds. To cancel the sleep timer, press SLEEP repeatedly until the display turns to hm. SLEEP hm GAME MODE After connecting a TV Game to the unit (see page ), press GAME. The TV screen changes to the Game mode. GAME The Game mode screen is adjusted to the suitable brightness for your eyes. If GAME is pressed during standby mode, the unit turns on automatically and the Game mode screen appears on the screen. Interactive video games that involve shooting a gun type of joy-stick at an on-screen target may not work on this TV/DVD. HEADPHONES Insert a stereo headphones (not supplied) with a / mini plug into the HEAD PHONES jack on the front panel. If you connect headphones, the sound from TV speakers is muted. Captions: This closed caption mode will display text on the screen in English or another language (depending on the setting of the closed captions CH /). Generally, closed captions in English are transmitted on captions channel and closed captions in other languages are transmitted on captions channel. Text: The text closed caption mode will usually ll the screen with a programming schedule or other information. After selecting a closed caption mode, it will stay in effect until it is changed, even if the channel is changed. If the captions signal is lost due to a commercial or a break in the signal, the captions will reappear when the signal is received again. If the channels are changed, the captions will be delayed approximately seconds. The captions will appear in places on the screen where they will least interfere with the picture, usually on the bottom of the screen. News programs will usually show three-line closed captions which scroll onto the screen. Most other shows provide two or three lined captions placed near the character who is speaking so the viewer can follow the dialogue. Words in italics or underlined describe titles, words in foreign languages or words requiring emphasis. Words that are sung usually appear enclosed by musical notes. For television programs broadcasting with closed captions, look in your TV guide for the closed captions symbol (CC). TO VIEW CLOSED CAPTIONS Press CLOSED CAPTION to switch between normal TV and the two closed caption modes (captions and full screen text). Closed captioning will display text on the screen for hearing impaired viewers. You can also select the closed captions in SETUP menu in the TV mode. CLOSED CAPTION OFF tes: When selecting closed captions, the captioning will be delayed approximately seconds. If no caption signal is received, no captions will appear, but the television will remain in the caption mode. Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with closed captioning, especially with live programs. This is because during live programs, captions are also entered live. These transmissions do not allow time for editing. When captions are being displayed, on-screen displays, such as volume and mute may not be seen or may interfere with closed captions. Some cable systems and copy protection systems may interfere with the closed captioned signal. If using an indoor antenna or if TV reception is very poor, the closed caption decoder may not appear or may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception or use an outdoor antenna. TV operation MUTE JXA(Eng).indb // :: JXA(Eng).indb // ::9 TV operation Picture control adjustment/ Adjusting the picture mode Selecting the color temperature Picture controls are factory preset but you can adjust them individually as follows: And also you can select four picture modes Standard, Sports, Movie, and Memory as described in the following table: CAEL CAEL / / / / / / MENU MENU Picture control adjustment Press MENU and then press or to select PICTURE. PICTURE AUDIO SETUP PICTURE Adjusting the picture mode Press MENU and then press or to select PICTURE. PICTURE AUDIO SETUP Selecting the color temperature Press MENU and then press or to select PICTURE PICTURE AUDIO SETUP MODE SPORTS PICTURE PICTURE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS :SELECT :ADJUST Press or to select the item you want to adjust, then press or to adjust the setting. Selection PICTURE AUDIO SETUP PICTURE MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS :SELECT SPORTS :ADJUST Pressing BRIGHTNESS darker lighter CONTRAST lower higher COLOR paler deeper TINT reddish greenish SHARPNESS softer sharper te: The CONTRAST default setting is set to maximum (+) at the factory. Press CAEL to clear the menu screen. CAEL To return all adjustments to the factory preset levels Press or to select RESET, then press. Mode Press or to select MODE, then press or to select the desired picture mode. Picture quality MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS :SELECT SPORTS Bright and dynamic picture (factory-set) STANDARD Standard picture quality (factory-set) MOVIE Movie-like picture setting (factory-set) MEMORY Your personal preferences (set by you; see Picture control adjustment as left) te: You cannot select MODE in the Game mode. SPORTS PICTURE AUDIO SETUP :ADJUST PICTURE MODE SPORTS SPORTS/STANDARD/MOVIE/MEMORY BRIGHTNESS CONTRAST COLOR TINT SHARPNESS :SELECT :ADJUST Press CAEL to clear the menu screen. CAEL Press or to select the desired color mode. Press or to select COLOR TEMPERATURE. Mode COOL MEDIUM WARM Picture quality Bluish Neutral Reddish MODE BRIGHTNESS CONTRAST COLOR TINT SHARPNESS :SELECT PICTURE SPORTS PICTURE AUDIO SETUP :ADJUST COLOR TEMPERATURE COOL COOL/MEDIUM/WARM RESET :SELECT PICTURE AUDIO SETUP PICTURE :ADJUST COLOR TEMPERATURE WARM COOL/MEDIUM/WARM RESET :SELECT :ADJUST Press CAEL to clear the menu screen. CAEL TV operation te: You cannot select COLOR TEMPERATURE in the Game mode. JXA(Eng).indb // :: JXA(Eng).indb // ::

10 Reading TV operation Basic playback Sound control adjustment/ Stereo and Second Audio Program (SAP) Sound controls are factory preset but you can adjust them individually as follows: The TV/DVD is equipped with a feature known as multi-channel TV sound or MTS. MTS broadcasts greatly enhance TV viewing by bringing you programs with high delity stereo sound. MTS also provides an extra channel called the Second Audio Program or SAP which broadcasters can use to transmit a second language for bilingual transmission or for other purposes. CAEL / / / MENU Playing a disc This section shows you the basics on how to play a disc. CAUTION Keep your ngers well clear of the disc slot when disc is loading or unloading. Neglecting to do so may cause serious personal injury. POWER VOLUME +/ PLAY STOP EJECT Sound control adjustment Listening to stereo sound DVD VCD CD Basic playback Press MENU and then press or to select AUDIO. PICTURE AUDIO SETUP AUDIO MTS BASS TREBLE BALAE SURROUND RESET :SELECT STEREO OFF :ADJUST Press or to select the item you want to adjust, then press or to adjust the setting. PICTURE AUDIO SETUP AUDIO MTS BASS TREBLE BALAE SURROUND RESET :SELECT STEREO OFF :ADJUST MTS Press or to select STR (STEREO), SAP or MONO. BASS: Press or to adjust the bass sound. TREBLE: Press or to adjust the treble sound. BALAE: Press or to obtain an equal sound level from both speakers. SURROUND: Press or to select ON or OFF. ON: The dynamic presence and sound created offers a thoroughly enjoyable listening experience. OFF: rmal sound. Press CAEL to clear the menu screen. CAEL Repeat step in Sound control adjustment on left, then press or to select MTS. Then press or to select STR. When the TV is turned on or a channel selection is made, the STEREO will appear on the screen. This means that Stereo broadcasting is available. You can enjoy stereo sound from the left and right speakers. When mono broadcasting is received, no indication is displayed. If the broadcast signal is not strong enough or clear stereo sound is not available, select MONO. The noise may be eliminated. STEREO Listening to SAP (Second Audio Program) Repeat step in Sound control adjustment on left, then press or to select MTS. Then press or to select SAP. When the TV is turned on or a channel selection is made, the SAP will appear on the screen. This means that the Second Audio Program broadcasting is available. STEREO SAP Preparations: When connecting to other equipment, turn the power off. Press POWER on the unit or on the remote control to turn on the unit. The Power indicator on the front of the main unit will light. Every time you press POWER, the TV/DVD starts from TV mode. When using an ampli er, switch on the ampli er. Press TV/DVD on the remote control to select DVD mode. The DVD startup screen will appear on the screen. Load a disc in the disc slot. Load the disc in the disc slot with the label side facing forward. (If the disc has a label.) Hold the disc without touching either of its surfaces, align it with the guides, and place it in position. On the TV-screen, changes to Reading and then playback commences. A menu screen will appear on the TV screen if the disc has a menu feature. Press / or / to select title, then press ENTER. Title is selected and play commences. Press VOLUME + or to adjust the volume. VOLUME Press STOP to end playback. Resuming facility The unit records the stopped point, depending on the disc. appears on the screen. Press PLAY to resume playback (from the scene point). If you press STOP again ( appears on the screen.), the unit will clear the stopped point. Basic playback To return BASS/TREBLE/BALAE control adjustments to the factory preset levels Press or to select RESET, then press. To start playback in the stop mode Press PLAY. te: If the unit does not operate properly: Static electricity, etc., may affect the TV/DVD s operation. In such case, disconnect the AC cord, then connect it again. 9 JXA(Eng).indb 9 // :: Basic playback Playing a disc (Continued) To obtain a higher quality picture Occasionally, some picture noise may appear on the TV screen while playing a DVD video disc because the high resolution pictures on these discs include a lot of information. In such case, you may reduce the SHARPNESS with the Picture control adjustment menu (see page ). About DVD VCD CD The DVD VCD CD icons on the heading bar show the playable discs for the function described under that heading. : You can use this function with DVD video discs. VCD : You can use this function with Video CDs. CD : You can use this function with Audio CDs and CD-R/RW CDs. DVD VCD CD Basic playback To pause playback (still mode) Press PAUSE during playback. To resume normal playback, press PLAY. To stop playback Press STOP. The sound is muted during still mode. POWER TV/DVD EJECT VOL +/ ENTER / / / PAUSE PLAY STOP To remove the disc Press EJECT. Remove the disc after the disc comes out. tes: If a non-compatible disc is loaded, Incorrect Disc, Region Code Error or Parental Error will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (see pages and ). Some discs may take a minute or so to start playback. When you set a single-faced disc label downwards (ie. the wrong way up), Reading will appear on the display for a few minutes and then Incorrect Disc will continue to be displayed. Some discs may not work the resuming facility. Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC, see page. Some playback operations of DVDs may be intentionally xed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs. Do not move the unit during playback. Doing so may damage the disc. Use the EJECT button to unload and eject the disc. Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunctions. There may be a slight delay between the button is pressed and the function activates. DVD VCD CD Playing in fast reverse or fast forward directions Press REV or FWD during playback. REV: Fast reverse playback FWD: Fast forward playback DVD VCD Each time you press REV or FWD button, the playback speed changes. Playing frame by frame Press PAUSE during still playback. Each time you press PAUSE, the picture advances one frame. DVD VCD Press SLOW (REVERSE) or (FORWARD) during playback. Each time you press the button, the slow-motion speed changes. DVD VCD CD Playing in slow-motion Locating a chapter or track To resume normal playback Press PLAY. To resume normal playback Press PLAY. te: The sound is muted during frame by frame playback. To resume normal playback Press PLAY. tes: The sound is muted during slow-motion playback. The Video CD cannot play Reverse Slow. Press SKIP or repeatedly to display the chapter or track number you want. Playback starts from the selected chapter or track. To locate succeeding chapters or tracks. Playback starts from the beginning of the current chapter or track. When you press twice in quick successions, playback starts from the beginning of the preceding chapter or track. te: A Prohibition symbol may appear at the upper right of the screen. This symbol means either the feature you tried is not available on the disc, or the TV/DVD cannot access the feature at this time. This does not indicate a problem with the TV/DVD. REV PLAY PAUSE FWD SKIP / SLOW / tes: The TV/DVD mutes sound during reverse and forward scan of DVD and Video CD discs. However, the TV/DVD plays sound during fast forward or fast reverse play of audio CDs. The playback speed may differ depending on the disc. Basic playback JXA(Eng).indb // :: JXA(Eng).indb // ::

11 Advanced playback Zooming/Locating desired scene 9 Repeat playback/a-b Repeat playback PLAY MODE ZOOM JUMP CAEL ENTER / / / ENTER PLAY SKIP / REPEAT A-B RECALL Zooming DVD VCD CD This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame. Press ZOOM during playback. The center part of the image will be zoomed in. Each press of ZOOM will change the ZOOM (x.), (x.) and (x.). Press / / / to view a different part of the frame. You may move the frame from the center position to UP, DOWN, LEFT or RIGHT direction. In the zoom mode, press ZOOM repeatedly to return to a : view ( Off). tes: You can select the Pause, Slow or Search playback in the zoom mode. Some discs may not respond to zoom feature. DVD VCD CD Use the title, chapter and time recorded on the DVD disc to locate the desired point to playback. In the case of VCD/Audio CD discs, time and track are used to locate the desired point to playback. To check the title, chapter/track and time, press RECALL. Locating desired scene Press JUMP during playback or resume stop mode. Title Chapter Time Jump Press or to select the Time, Title/ Track or Chapter. Title Chapter Time Jump Press Number buttons ( 9) to input the number. Title Chapter Time Jump If you input a wrong number, press CAEL. Refer to the package supplied with the disc to check the numbers. Press ENTER. Playback starts. When you change the title, playback starts from Chapter of the selected title. Some discs may not work in the above operation. te: In case of the Video-CD playback with PBC, the JUMP does not work. To turn off PBC, see page. Repeat playback DVD VCD Press PLAY MODE during playback or stop mode. [DVD] Press ENTER repeatedly to select Chapter or Title. The unit automatically starts repeat playback after nishing the current title or chapter. [Video CD] Press to select Repeat. Press ENTER repeatedly to select Track or All. The unit automatically starts repeat playback after nishing the current track. If you set the repeat mode during stop mode, press PLAY to start Repeat playback. [Audio CD and MP/WMA CD] Please see Repeat playback (CD). Press PLAY MODE again to clear the screen. To resume normal playback Select Repeat : Off in step. Repeat Mode Repeat Play Mode tes: Some discs may not work with the repeat operation. In case of Video CD with PBC, Repeat function is prohibited during playback. Chapter/Track repeat function is canceled whenever SKIP or is pressed. : Off Play Mode : Off : Off DVD VCD CD A-B Repeat playback A-B repeat playback allows you to repeat a section between two selected points. Press REPEAT A-B during playback. The start point is selected. Press REPEAT A-B again. The end point is selected. Playback starts at the point that you selected. Playback stops at the end point and returns to Point A automatically, then starts again. To resume normal playback Press REPEAT A-B again. Off appears on the screen. tes: In A-B Repeat mode, subtitles near the A or B locations may not be displayed. You cannot set the A-B Repeat for the scenes that include multiple angles. A-B Repeat playback does not work when Repeat playback is activated. You may not be able to set A-B Repeat during certain scenes of the DVD. A-B Repeat does not work with an interactive DVD, MP/ WMA/JPEG CD. In case of Video CD with PBC, A-B Repeat is prohibited. A A B Advanced playback JXA(Eng).indb // :: JXA(Eng).indb // :: Advanced playback Program playback/random playback You can arrange the playback order of tracks or les on the disc. And the unit can also select tracks or les at random and playback them. These feature works for Video CD. For Audio CD and MP/WMA CD, please see Random playback (CD) and Program playback (CD). 9 CAEL PLAY MODE / / / ENTER PLAY Changing angles/title selection/dvd menu TOP MENU DVD MENU / / / ENTER PLAY ANGLE VCD VCD Program playback Press PLAY MODE in the stop mode. Mode Random playback Play Mode : Off Repeat : Off Program Playback Mode Play Mode : Program Repeat : Off Program Playback Play Mode Mode : Program Repeat : Off Program Playback Press or to select Mode, then press ENTER repeatedly to select Program Press / to select the programming position. Press / and then use Number buttons ( 9) to input the track. To program others, repeat step. If you input a wrong number, press CAEL Press PLAY MODE during playback or stop mode. Press / to select Mode, then press ENTER to select Random. Mode Play Mode : Random Repeat : Off Program Playback Press / to return to the left column, then press / to select the Program Playback and press ENTER. The programs you selected will start to playback in order. To resume normal playback, select Mode: Off in step. To change the program. Select Mode to Program (as step ), press / / / to select the track/ le number you want to change, then press CAEL.. Press Number buttons ( 9) to overwrite the new track/ le number. To clear the program one by one Select Mode to Program, press / / / to select the track number. Then press CAEL. To clear all the programs At the left column, press / to select Clear Program. Then press ENTER. tes: In playing back the Video CD with PBC, you cannot set Program playback. The program is canceled when you eject the disc or turn the power off. Press PLAY. Play Mode Mode : Program Repeat : Off Program Playback 9 The Random Playback will start. If you set Random during playback mode, Random playback will begin after the track/ le that is currently being played has ended. To resume normal playback, select Mode: Off in step. te: In case of Video CD with PBC, you cannot set Random function during playback. Changing angles When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from. Press ANGLE during playback. Press ANGLE repeatedly until the desired angle is selected. The current angle will appear. Title selection DVD menu te: Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the DVD. Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title. Press TOP MENU during playback. Press ENTER or PLAY. Title menu appears on the screen. The playback of the selected title will start. Press / / / to select the desired title. Press DVD MENU during playback. The DVD menu appears on the screen. Press DVD MENU again to resume playback at the scene when you pressed DVD MENU. Press / / / to select the desired item. te: Depending on the DVD, you may not be able to select the title. Depending on the DVD, a title menu may simply be called a menu or title in the instructions supplied with the disc. Some DVDs allow you to select the disc contents using the menu. When you playback these DVDs, you can select the subtitle language and soundtrack language, etc. using the menu. / Press ENTER. The menu continues to another screen. Repeat steps and to set the item completely. te: Depending on the DVD, you may not be able to resume playback from the scene point when you press the DVD MENU button. Advanced playback JXA(Eng).indb // :: JXA(Eng).indb // ::

12 /MP-.MP Select Files Repeat :Off Mode :Off Select Files Repeat :Off Mode :Off Advanced playback Changing soundtrack language/ Subtitles Disc status/to turn off the PBC RECALL PLAY MODE SUBTITLE AUDIO / ENTER DVD VCD Changing soundtrack language You can select the language when you play a multilingual disc. Press AUDIO during playback. The current soundtrack language will appear. / Eng Dolby Digital Press AUDIO repeatedly until the desired language is selected. / Fre Dolby Digital The on screen display will disappear after a few seconds. In case of Video CD playback Audio type changes as follows each time you press AUDIO. LR L R Subtitles When playing back a disc recorded with subtitles, you can select the subtitle language or turn the subtitle off. Press SUBTITLE repeatedly during playback until the desired language is selected. / Eng To turn off the subtitle, press SUBTITLE until Off appears. The on screen display will disappear after a few seconds. tes: Depending on the DVD, you may not be able to change subtitles, or to turn subtitles on or off. While playing a DVD, the subtitle may change when you loaded or eject the disc. In some cases, a selected subtitle language may not be changed immediately. Off DVD VCD Disc status With press of RECALL, the status of the disc will appear on the screen. To cancel the display, press RECALL again. DVD DISC OPERATION TITLE NO. ANGLE NO. AUDIO LANGUAGE Video CD DISC OPERATION ELAPSED TIME DVD :: ::9 Title / Chapter / / Digital / Eng Eng Dolby / TOTAL TIME CHAPTER NO. SUBTITLE LANGUAGE A KIND OF AUDIO ELAPSED TIME TOTAL TIME VCD To turn off the PBC (see page ) Press PLAY MODE in the stop mode. Press / to select Mode, then press ENTER repeatedly until Off appear. Play Mode Mode : Off --- Repeat : Off Program Playback Press PLAY MODE again to clear the screen. To turn on the PBC Follow the above steps ~, then press ENTER repeatedly until PBC appear. te: You can also turn off the PBC by pressing number button and ENTER in the stop mode. Advanced playback tes: If the desired language is not heard after pressing the button several times, the language is not recorded on the disc. The selected soundtrack language is canceled when you eject the disc. The initial default language or available language will be heard if the disc is played back again. If you select DTS in playing DTS-encoded disc, no sound will be heard from the TV/DVD s speakers. VCD :: :: Track / TRACK NO. JXA(Eng).indb // :: JXA(Eng).indb // :: Advanced playback MP/WMA/JPEG/DivX and Audio CD operation This player can playback the MP/WMA/JPEG/DivX -data which has been recorded on CD-R or CD-RW. To produce the MP/WMA/JPEG/DivX -data, you need a Windows-PC with CD-RW drive and a MP/WMA/JPEG/DivX -encoding Software (not supplied). The Apple-HFS-System cannot be played. This player requires discs/recordings to meet certain technical standards in order to achieve optimal playback quality. There are many different types of recordable disc formats (including CD-R containing MP/WMA les). t all recordable discs will produce optimal playback quality. The technical criteria set forth in this owner s manual are meant only as a guide. Use of CD-RW for MP les is not recommended. You must obtain any required permission from copyright owners to download or use copyrighted content. Toshiba cannot and does not grant such permission. CD Audio CD/MP/WMA/JPEG/DivX CD information Limitations on MP/WMA/JPEG/DivX CD playback MP/WMA/JPEG/DivX CD is the disc that is standardized by ISO9, its le name must include -digits extension letters,.mp,.wma,.jpg,.div,.divx,.avi. MP/WMA/JPEG/DivX CD must be corresponded to the ISO standardized les. This unit can read les per disc. If one directory has more than les, it reads up to les, the remaining les will be omitted. The unit is able to recognize up to a maximum of directories per disc. MP/WMA/JPEG/DivX CDs cannot be used for the purpose of recording. If the CD has both CDA audio tracks and MP/WMA/JPEG/DivX les, only the CDA audio tracks will be played. It may take more than one minute for this unit to read MP/WMA/JPEG/DivX les depending on its structure. Music recorded by Joliet Recording Speci cation can be played back, the le name is displayed (within letters) on the screen. Long le names will be condensed. The music les recorded by Hierarchical File System (HFS) cannot be played. Limitations on display The maximum number for display is letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of through 9, and _ (under score). Other letters than those above are replaced in hyphen. tes on MP/WMA/JPEG/DivX les To playback MP/WMA/JPEG/DivX CD in the recorded order,. Use MP/WMA/JPEG/DivX software that records data alphabetically or numerically.. Name each le including two-digit or three-digit number (ex. or ).. Refrain from making too many sub-folders. CAUTION: Some MP/WMA/JPEG/DivX CDs cannot be played back depending on the recording conditions. The CD-R/RW that has no music data or non MP/WMA/JPEG/DivX les cannot be played back. Standard, sampling frequency and the bit rate: MP CD MPEG- Audio khz,.khz, khz kbps ~ kbps (constant bit rate or variable bit rate) The recommend recording setting for a high-quality sound is.khz of sampling frequency and kbps of constant bit rate. WMA CD WMA version and khz/kbps,.khz/kbps~9kbps, khz/kbps~9kbps The le recorded by mono, khz, kbps is not available to this unit. DivX video DivX version: DivX,,, and (speci cally..,..,..,..,..,..,. at Home Theater pro le). Audio format: MPEG Layer (MP), MPEG Layer (MP) Sampling frequencies: khz,.khz, khz Bit rate: kbps ~ kbps Resolution: Max x (at fps), Max x (at fps) Microsoft, Windows Media, and Windows Logo are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DivX, DivX Certi ed, and associated logos are trademarks of DivX, Inc. and are used under license. CD MP/WMA CD playback Load a disc on which MP or WMA les have been recorded in the disc slot. A le browser screen will appear on the screen. Press / to select le. Folder- Folder- MP- MP- MP- WMA- WMA- WMA- Folder- Folder- MP- MP- MP- WMA- WMA- WMA- JPEG Preview In case the current directory includes more than les, press or to scroll in the le list. To see contents in folder, select the folder and then press ENTER. To return to the parent directory, select Go Up... then press ENTER. When PLAY is pressed after the le browser displayed, playback begins automatically starting from the rst le. In this case, if the rst le is an MP/WMA le, only MP/WMA les are played back in order. If the rst le is a JPEG le, the rst JPEG le is played back. If the rst le is a DivX le, the rst DivX le is played back. If there is no le at a root directory, playback does not begin automatically. Press ENTER. The selected le starts playing back. Press STOP to end playback. JPEG Preview The unit records the stopped point. appears on the screen. Press PLAY to resume playback (from the scene point). If you press STOP again or unload the disc, the unit will clear the stopped point. About le menu / :: /Folder-/WMA-.WMA MP- MP- WMA- WMA- Picture- Picture- Movie- Movie- Select Files Repeat :Off Mode :Off Music Playing TOP MENU / / / ENTER RETURN PLAY STOP tes: The thumbnail list is displayed when the FUJICOLOR CD or the Kodak Picture CD are played. To display the le browser, press TOP MENU. In the case of a CD containing a mixture of MP, WMA, JPEG and DivX les, the les are played back by selecting them from the le browser. MP or WMA le on the Kodak Picture CD is not recognized on this unit. tes: During MP/WMA/JPEG/DivX Playback, you cannot use JUMP and A-B Repeat functions. You can use Repeat (Track or All), Random functions and Program playback foraudio CD/MP/WMA/JPEG/DivX CD Playback,. Select Files The le type to make it display in the le browser can be chosen.. Press or to highlight Select Files at right column in the le browser.. Press ENTER, then press or to select le type from the list (Music, Picture or Movie).. Press ENTER to add/remove check mark. Checked le type will be displayed in the le browser.. Press RETURN to save the setting. 9 Advanced playback JXA(Eng).indb // :: JXA(Eng).indb 9 // ::

13 /Picture-.JPG Select Files Repeat :Off Mode :Off W: H: Advanced playback MP/WMA/JPEG/DivX and Audio CD operation (Continued) You can select your desired JPEG le on the le menu and picture menu. The selected JPEG le is automatically adjusted to the TV screen. (When the aspect ratio of the JPEG le is different to the TV screen, the black bar will appear at the top and bottom, or the both sides of the TV screen.) STOP TOP MENU DVD MENU / / / ENTER PAUSE PLAY SKIP ANGLE STOP / ENTER PLAY CD Load a JPEG disc in the disc slot. A le browser screen Picture- will appear on the Picture- Picture- screen. JPEG CD playback Picture- Picture- Picture- Picture- Picture- JPEG Preview Press / to select the le. To display a thumbnail list, press DVD MENU. Press / or / to select the desired le. (To return to a le browser, press TOP MENU.) When PLAY is pressed after displaying the le browser, playback begins automatically starting from the rst le. In this case, if the rst le is a JPEG le, the rst JPEG le is played back. If the rst le is a DivX le, the rst DivX le is played back. If the rst le is an MP/WMA le, only MP/ WMA les are played back in order. If there is no le at a root directory, playback does not begin automatically. Press ENTER or PLAY. The selected picture appears on the screen. CD Slide show playback The slide show enables you to view pictures ( les) one after another automatically. Preparation: Set JPEG Interval setting to Seconds, Seconds or Seconds. Select your desired starting le for the slide show in the step on left. Press ENTER or PLAY to start slide show from the selected le. If you press PAUSE during the slide show, the slide show stops temporary. appears brie y on the screen. If the picture appears upside down or sideways, press ANGLE repeatedly until it s right side up.,, or appears on the screen. Press PLAY or SKIP again to resume the slide show. When the slide show playback nished, the le list appears. To stop the slide show, press STOP. The le list appears. tes: Zoom function also can be used in viewing JPEG les. See Zooming. During JPEG playback, you cannot use Jump and A-B Repeat functions. CD Load a disc on which DivX les have been recorded in the disc slot. A le browser screen will appear on the screen. Press / to select le. DivX CD playback /Movie-.DIVX Movie- Movie- Movie- Movie- Movie- Movie- Movie- Movie- Select Files Repeat :Off Mode :Off JPEG Preview When PLAY has been pressed after displaying the le browser, playback begins automatically starting from the rst le. In this case, if the rst le is a JPEG le, the rst JPEG le is played back. If the rst le is a DivX le, the rst DivX le is played back. If the rst le is an MP/WMA le, only MP/WMA le are played back in order. If there is no le at a root directory, playback does not begin automatically. Press ENTER or PLAY. The selected DivX movie will be played back on the screen. CD Playing DivX VOD content DivX VOD content is protected by DRM (Digital Rights Management) system. This restricts playback of content to speci c registered devices. If the incorrect DRM le is loaded, Authorization Error This player is not authorized to play this video. will appear on the screen. When you attempt to play DivX VOD, the number of plays is limited and the View DivX VOD Rental This rental has views left. Do you want to use one of your views now? right message will appear on the screen. If you wish to play it, select. If the number of plays goes over the limit, then Rental Expired will be displayed. In this case, the le will not be played. tes: In order to play DivX VOD content on this unit, you rst need to register the unit with registration code. See page 9. Depending on the recording conditions of DivX le, you may not be able to use FF, REV or JUMP function. Advanced playback Rotating an image You can rotate an image by 9 degrees. Press ANGLE during playback of the image.,, or appears on the screen. Press STOP to end playback. The le browser appears on the screen. If you want to watch the other le, repeat steps ~. Press STOP to end playback. The le browser appears on the screen. If you want to watch the other le, repeat steps ~. JXA(Eng).indb // ::9 JXA(Eng).indb // :: Advanced playback Repeat and program playback using le browser / / / ENTER / / / ENTER PLAY SKIP / PLAY CD Repeat playback (CD) In the le browser, press / / / to select Repeat during stop mode. CD Random playback (CD) In the le browser, press / / / to select Mode during stop mode. CD Program playback (CD) In the le browser, press / / / to select Edit Mode, then press ENTER. Press / / / to select Program View, then press ENTER. Program View shows only the programed les that you have added in step. Folder- Folder- MP- MP- MP- Folder- Folder- MP- MP- MP- Select Files Repeat :Off Mode :Off Press ENTER to select Track or All. Select Files Repeat :Track Mode :Off Press PLAY. The unit automatically starts repeat playback after nishing the current track. To resume normal playback Select Repeat : Off in step. Folder- Folder- MP- MP- MP- Press ENTER to select Random. Folder- Folder- MP- MP- MP- Select Files Repeat :Off Mode :Off Select Files Repeat :Off Mode :Random Press PLAY. The Random playback will start. To resume normal playback Select Mode : Off in step. tes: te: The repeat function is canceled when you eject the disc or The Randam function is canceled when you eject the disc or turn the power off. turn the power off. In case of Audio CD, the function of A-B Repeat can be used. See A-B Repeat playback. Track repeat function is canceled whenever SKIP or is pressed. Folder- Folder- MP- MP- MP Repeat :Off Mode :Off Edit Mode When Edit Mode is black color, you can mark the les which you want to add into Program list. Press / / / to select le you want to add into the program list. Folder- Folder- MP- MP- MP- WMA- WMA Repeat :Off Mode :Off Edit Mode JPEG Preview Press ENTER. Selected le was marked. Repeat this procedure to select the other les. Press / / / to select Add To Program. Then press ENTER. All marked les are added into the program list. Folder- Folder- MP- MP- MP- Edit Mode Program View Add To Program WMA- JPEG Preview WMA- When you nish storing the les which you want into the Program list, select Edit Mode and press ENTER to release edit mode. Program View Browser View MP- MP- MP- WMA- Folder- Folder- MP- MP- MP- WMA- WMA- WMA- Edit Mode Browser View Clear Program JPEG Preview Edit Mode Program View Add To Program JPEG Preview In the Program View, press PLAY. The les start to playback in programmed order that were added by you. To remove le from program list in Stop mode In the Edit Mode, switch to Program View. Select le you want to remove, then press ENTER. Select Clear Program and press ENTER. Marked le is removed from program list. te: The program function is canceled when you eject the disc or turn the power off. Advanced playback JXA(Eng).indb // :: JXA(Eng).indb // ::

14 Function setup Customizing the function settings You can change the default settings of the DVD mode to customize performance to your preference. SETUP ENTER / / / RETURN DVD VCD CD Setting procedure Press SETUP during stop mode. The following on-screen display appears. Parental DRC E.B.L. Menu : English Off TV Subtitle QSound Screen Set Password : English : On Output Display Audio : English Interlace On Picture Mode DivX(R) : VOD Auto JPEG Interval : Seconds Screen Saver : On Press or to select the desired section, then press. Parental DRC Menu TV Screen : Off English : Change the selection using or, by referring to the corresponding pages ~ 9. Press ENTER to save the setting. Repeat steps and to change other option. To select another section, go back to step by pressing repeatedly. To clear SETUP screen, press SETUP or RETURN. Setting details Section Option Menu Subtitle Audio TV Screen Display Details To select the language of Menu, Subtitle and Audio if more than one language are available on the disc. To select a picture size according to the aspect ratio of your TV. To turn On or Off the operational status display on the screen. Page Subtitle Display QSound Set Password : English On Output Audio Picture Mode : English Interlace Auto JPEG Interval DivX(R) : VOD Off First option will be highlighted. Press or to select the desired option. Parental DRC Menu TV Screen : Off English : Picture Mode JPEG Interval DRC To select a preferred picture mode from Video, Film or Auto. To select a preferred setting for the slide show playback. To select On or Off for DRC (Dynamic Range Control). Function setup Subtitle Display QSound Set Password : English On Output Audio Picture Mode : English Interlace Auto JPEG Interval DivX(R) : VOD Off Then press or ENTER. The selectable settings will appear. Parental DRC Menu TV Screen : : Off English Subtitle Display QSound Set Password : : English On Output Audio Picture Mode : English Interlace Auto JPEG Interval DivX(R) : VOD Off Parental Password DivX(R) VOD To select a preferred parental level for the parental setting. To change the password. To display your -character registration code. 9 JXA(Eng).indb // :: JXA(Eng).indb // :: Function setup Customizing the function settings (Continued) Setting details Parental DRC E.B.L. Menu : English Off Parental DRC Menu TV Screen : : Off English Picture Mode JPEG Interval QSound TV Subtitle Screen Set Password : : On English Output Audio Display : On English Interlace Picture Mode DivX(R) : VOD Auto JPEG Interval : Seconds Screen Saver : On Menu, Subtitle, Audio You can select the language of Menu, Subtitle and Audio if more than one languages are recorded onto the disc. English, Francais, Espanol: The selected language will be heard or seen. Other: Other language can be selected (see Language code list ). Original (Audio): The unit will select the rst priority language of each disc. Off (Subtitle): Subtitles do not appear. tes: If the selected language is not recorded on the disc, the rst-priority language is selected. If you want to change the OSD language, you can perform it by TV SETUP MENU. Display Subtitle QSound Set Password : On English Picture Output Audio Mode : Auto English Interlace JPEG Interval DivX(R) : VOD Off TV Screen You have the following screen sizes to choose from: : (Letter box): Select this mode when connecting to a conventional TV. When playing back a wide screen-dvd disc, it displays the wide picture with black bands at the top and bottom of screen. : (Pan & scan): It displays the wide picture on the whole screen with left and right edges automatically cut off. te: If the DVD disc is not formatted in the Pan & scan style, it will display : style. Display On screen display can be switched on or off when you press any buttons. There are two types of source content in pictures recorded in DVD video discs: lm content (pictures recorded from lms at frames per second) and video content (video signals recorded at frames per second). Make this selection according to the type of content being viewed. Auto: Select this selection normally. The DVD player automatically detects source content, lm or video of playback source, and converts that signal in the progressive output format in an appropriate method. Film: The DVD player converts lm content pictures in the progressive output format appropriately. Suitable for playback of lm content pictures. The progressive output feature will be most effective under this selection. Video: The DVD player lters video signal and converts it in the progressive output format appropriately. Suitable for playback of video content pictures. te: Depending on the disc, pictures may be cut off or doubled. In this case, select Video. You can continuously playback all JPEG les automatically. After the selection below, the disc will start playback on JPEG les which have been recorded. Off: Plays back one le at a time. Seconds: Plays back images in the form of a slide show at second intervals. Seconds: Plays back images in the form of a slide show at second intervals. Seconds: Plays back images in the form of a slide show at second intervals. Function setup On: On screen displays appear when you press the buttons (factory setting). Off: On screen displays do not appear when you press any buttons. JXA(Eng).indb // :: JXA(Eng).indb // ::

15 Function setup Customizing the function settings (Continued) Setting details Parental E.B.L. DRC : Off DRC Menu E.B.L. Parental : Off English Set the new password TV Screen Set Password : : Output Display : On Interlace Picture Mode DivX(R) : VOD Auto JPEG Interval : Seconds Screen Saver : On DRC DRC (Dynamic Range Control) enables you to control the dynamic range so as to achieve a suitable sound for your equipment. Off: It plays back at the recording level on the disc. On: Loud sound such as explosion is toned down slightly when played back. This is suitable when it is connected to a stereo. tes: This function works only during playback of Dolby Digital recorded discs. The level of Dynamic Range Reduction may differ depending on DVD video disc. Subtitle TV Password QSound Screen : : Change On English Display Audio DivX(R) VOD : Display On English Picture Mode : Auto JPEG Interval : Seconds Screen Saver : On Parental control setting Some discs are speci ed as not suitable for children. Such discs can be limited not to playback with the unit. ) Press or to select Parental, then press ENTER. Enter Password screen will appear. ) Press using Number buttons ( 9). (Please note, this is pre-setting password of this unit). Then press ENTER. The parental level list will appear. Level Off: The parental control setting does not function. Level : All DVD software can be played back. Level : DVD software for adults cannot be played back. ) Press or to select from the level to level. The limitation will be more severe as the level number is lower. Then press ENTER. ) Press or to select Password, then press ENTER. Enter Current Password screen will appear. ) Press Number buttons ( 9) to input the current password (If the password has not been set yet after you purchase this unit, it is ). ) Then press ENTER. Enter New Password screen will appear. Press Number buttons ( 9) to input the new password. ) Press ENTER. w your new password has been set. Be sure to remember this number! If you forget the password. ) Press EJECT to remove the disc. ) While holding down on the remote control and then press STOP on the unit. Password Clear appears on the screen. w the password has been returned to the initial value ( ). DivX VOD In order to play DivX VOD (Video On Demand) content on this unit, you rst need to register the unit with your DivX VOD content provider. You do this by generating a DivX VOD registration code, which you submit to your provider. Function setup tes: Depending on the discs, the unit cannot limit playback. Some discs may not be encoded with speci c rating level information though its disc jacket says adult. For those discs, the age restriction will not work. The password is required every time when you change the parental level. If you input a wrong number, press CAEL. Press or to select DivX(R) VOD. Then press ENTER. Your -character registration code is displayed. Make a note of the code as you will need it when you register with a DivX VOD provider. Then press ENTER to select Done. te: If each setup (pages ~ 9 ) has completed, the unit can always work under the same condition (especially with DVD discs). Each setup will be retained in the memory even if you turn the power off. 9 JXA(Eng).indb 9 // :: Function setup Temporary cancel the rating level by DVD disc Depending on the DVD disc, the disc may try to temporarily cancel the rating level that you have set. It is up to you to decide whether to cancel the rating level or not. DVD Temporary cancel the rating level by DVD disc Load a DVD disc. If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows the Reading screen will change, depending on which disc is played. If you select YES with the ENTER key, password input screen will then appear. If NO is selected, press EJECT to remove the disc. Enter the password with Number buttons ( 9). Then press ENTER. To exit from the entry, press RETURN. Enter Password Playback will commence if the entered password is correct. EJECT 9 ENTER RETURN te: This temporary cancellation of rating level will be kept until the disc is ejected. When the disc is ejected, the original rating level will be set again automatically. Others Language code list Enter the appropriate code number for the initial settings Menu, Subtitle and/or Audio. Language Name Code Language Name Code Language Name Code Language Name Code Abkhazian Fiji Lingala Singhalese 99 Afar Finnish 9 Lithuanian Slovak 9 Afrikaans French Macedonian Slovenian 9 Albanian 9 Frisian Malagasy Somali 9 Amharic Galician Malay 9 Spanish 9 Arabic Georgian Malayalam Sundanese 9 Armenian German Maltese Swahili 9 Assamese 9 Greek Maori 9 Swedish 9 Aymara Greenlandic Marathi Tagalog Azerbaijani Guarani Moldavian Tajik Bashkir Gujarati Mongolian Tamil Basque Hausa Nauru Tatar Bengali; Bangla Hebrew 9 Nepali Telugu Bhutani Hindi 9 rwegian Thai Bihari Hungarian Oriya Tibetan Breton Icelandic 99 Panjabi Tigrinya 9 Bulgarian Indonesian 9 Pashto, Pushto 9 Tonga Burmese Interlingua 9 Persian Turkish Byelorussian Irish Polish Turkmen Cambodian Italian 9 Portuguese Twi Catalan Japanese Quechua Ukrainian Chinese Javanese Rhaeto-Romance Urdu Corsican Kannada Romanian Uzbek Croatian Kashmiri 9 Russian Vietnamese 9 Czech 9 Kazakh Samoan 9 Volapük Danish Kirghiz Sanskrit 9 Welsh Dutch Korean Scots Gaelic Wolof English Kurdish Serbian 9 Xhosa Esperanto Laothian Serbo-Croatian 9 Yiddish 9 Estonian Latin Shona 9 Yoruba Faroese Latvian, Lettish Sindhi 9 Zulu Others JXA(Eng).indb // :: JXA(Eng).indb // ::

16 Others Troubleshooting Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or service outlet if problems persist. Be sure all connections are properly made when using with other units. SYMPTOMS POSSIBLE SOLUTIONS PAGE POWER Make sure the connection of AC cord is secured. TV/DVD does not operate. Try another AC outlet. Unplug unit, then plug it back in. TV BROADCAST RECEPTION Poor sound or sound. Poor picture or picture. Poor reception on some channels. Poor color or no color. Picture wobbles or drifts. CATV reception. Horizontal or diagonal bars on screen. reception above channel. TV shuts off. Closed - Caption is not activated. Display is not shown in your language. Station or Cable TV may have problems, try another station. Check Volume adjustments. Check for sources of possible interference. Station or Cable TV may have problems, try another station. Check antenna or Cable TV connections, reorient antenna. Check for sources of possible interference. Check picture control adjustments. Station or Cable TV may have problems, try another station. Station signal is weak, reorient antenna to receive weaker station. Check for sources of possible interference. Station or Cable TV may have problems, try another station. Make sure channels are set into memory. Check picture control adjustments. Check antenna or Cable TV connections, reorient antenna. Check for sources of possible interference. Station or Cable TV may have problems, try another station. Make sure channels are set into memory. Cable TV company is scrambling signal. Check antenna or Cable TV connections, reorient antenna. Check all Cable TV connections. Set TV/CABLE selection to the CABLE position. Station or Cable TV system problems, try another station. Check antenna or Cable TV connections, reorient antenna. Check for sources of possible interference. Make sure TV/CABLE selection is in the appropriate position. If antenna is used, check UHF antenna connections. broadcast on station tuned. Auto shut off feature worked. Sleep Timer is set. Power interrupted. TV station experiencing problems or program tuned is not closed captioned. Try another channel. Check Cable TV connection or VHF/UHF antenna, reposition or rotate antenna. Press CLOSED CAPTION button to turn on the closed caption decoder.,, -,, -, Select proper language in the menu options. DVD SYMPTOMS POSSIBLE SOLUTIONS PAGE Playback doesn t start. disc is loaded. The disc may be dirty. Clean up the disc. The unit cannot play CD-ROMs, etc. picture. TV/DVD selector is not set correctly. 9 sound. Check the input selector of the ampli er is set properly. The unit is in the special playback mode. Select the correct Audio Input/Output position on AV ampli er. - Picture is distorted during fast The picture will be distorted occasionally. - reverse/forward playback. Stopping playback, search, slowmotion play, repeat play, or Some discs may not do some of the functions. - program play, etc. cannot be performed. on-screen display. Set Display to On. The unit or remote operation key is not functioning. Playback does not start when the title is selected. Audio soundtrack and/or subtitle language is not changed when you playback a DVD. Turn off the unit and unplug the AC power cord for several minutes, then replug it. Check the RATING LEVEL setup. Multilingual language is not recorded on the DVD disc. Some discs have no subtitles. subtitle. Subtitles are cleared. Press the SUBTITLE button. Angle cannot be changed. Multi-angles are not recorded on the DVD disc. appears on the screen. The function is prohibited with the unit or the disc. REMOTE CONTROL The remote control does not function. Aim the remote control at the remote sensor. Operate within approx. meters or reduce the light in the room. Clear the path of the beam. The batteries are weak. Replace the batteries. Check the batteries are inserted correctly. 9 - Others JXA(Eng).indb // :: Others Reception disturbances Speci cations Most types of television interference can be remedied by adjusting the height and position of the VHF/UHF antenna. Outdoor antennas are recommended for best results. The most common types of television interference are shown below. If one of these symptoms appear when the TV/DVD is connected to a Cable TV system, the disturbance may be caused by the local Cable TV company broadcast. IGNITION Black spots or horizontal streaks may appear, the picture may utter or drift. Usually caused by interference from automobile ignition systems, neon lamps or AC powered tools and appliances such as drills or hair dryers. General Power supply Power consumption Weight Dimensions Operating temperature Operating humidity Television AC V Hz (with supplied AC adapter) Operation: W, Stand by: W (with supplied AC adapter). lbs (. kg) Width: -/ inches ( mm) Height: -/ inches (. mm) Depth: 9-/ inches ( mm) C- C ( F- F) Less than % RH ( condensation) LCD panel -inch diagonal (Screen size is approximate.) Display method Color TFT LCD Number of pixels (Horizontal) x (Vertical) GHOSTS Ghosts are caused by the television signal following two paths. One is the direct path and the other is re ected by tall buildings, hills or other large objects. Changing the direction or position of the antenna may improve the reception. Tuner type F-Synth VHF: - Receiving channels UHF: -9 CATV: - (A, A-~A-, A~I, J~W, W+~W+) Antenna input VHF/UHF Speaker -/ x -/ inches (. x. mm), x Audio output power.w +.W DVD/CD Player SNOW If the TV/DVD is located far from the TV station, in a fringe reception area where the signal is weak, small dots may appear in the picture. If the signal is extremely weak, the installation of a larger external antenna may be necessary. Signal system Applicable disc Pickup Input/Output NTSC. DVD (cm, cm). CD (cm, cm) -Lens, -Beams System Others S-Video input (Y). V (p-p),, negative sync., Mini DIN -pin x (C). V (p-p), RADIO FREQUEY INTERFEREE (RFI) Caused by two-way radios, this type of interference produces moving ripples or diagonal streaks in the picture. Some cases may cause a loss of contrast in the picture. Changing the direction and position of the antenna or installing an RFI lter may improve the picture. (Y). V (p-p),, negative sync., pin jack x ColorStream video input (PB, PR). V (p-p),, pin jack x Video input. V (p-p),, negative sync., pin jack x Audio input dbm, k, negative sync., pin jack (L/R) x Digital audio output (Coaxial). V (p-p),, pin jack x Headphone ø.mm stereo mini jack x Accessories Remote control (DC-LB)... CARE AND MAINTENAE To prevent re or shock hazard, disconnect the TV/DVD from the power source before cleaning. Use caution when cleaning or wiping the plastic parts. Batteries (R/AAA)... AC adapter... AC cord (for AC adapter)... - matching transformer... Owner s manual (this booklet)... This model complies with the above speci cations. Designs and speci cations are subject to change without notice. This model may not be compatible with features and/or speci cations that may be added in the future. JXA(Eng).indb // :: JXA(Eng).indb // ::