Test Report. Applicant Address. : WALTOP International Corp. : 6F,No.19-1 Industry E.Rd.IV,Hsinchu Science Park,Hsin-Chu 30077,Taiwan,R.O.C.

Transcription

1 Test Report Product Name : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Model No. : Tablet: RCK-T7, RCK-T7S; Dongle: RCK-T7R, RCK-T7RS FCC ID. : Tablet: UBBRCKT7, Dongle: UBBRCKT7R pplicant ddress : WLTOP International Corp. : 6F,No.9- Industry E.Rd.IV,Hsinchu Science Park,Hsin-Chu 377,Taiwan,R.O.C. Date of Receipt : 27/4/3 Issued Date : 27/4/27 Report No. : 74H5-RFUSP5V The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Page: of 8

2 Test Report Certification Issued Date : 27/4/27 Report No. : 74H5-RFUSP5V Product Name pplicant ddress : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 : WLTOP International Corp. : 6F,No.9- Industry E.Rd.IV,Hsinchu Science Park,Hsin-Chu 377,Taiwan,R.O.C. Manufacturer : WLTOP International Corp. Model No. : Tablet: RCK-T7, RCK-T7S; Dongle: RCK-T7R, RCK-T7RS FCC ID. : Tablet: UBBRCKT7, Dongle: UBBRCKT7R Rated Voltage : C 2 V / 6 Hz EUT Voltage : C 2 V / 6 Hz Trade Name : WLTOP pplicable Standard : FCC CFR Title 47 Part 5 Subpart C Section 5.247: 25 Test Result : Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By : ( Sandy Chuang ) Reviewed By : ( Sheena Huang ) pproved By : ( Roy Wang ) Page: 2 of 8

3 TBLE OF CONTENTS Description Page. General Information EUT Description Operational Description Test Mode Tested System Details Configuration of tested System EUT Exercise Software Test Facility Peak Power Output Test Equipment Test Setup s Test Specification Uncertainty Test Result Conducted Emission Test Equipment Test Setup s Test Procedure Test Specification Uncertainty Test Result Test Photo Radiated Emission Test Equipment Test Setup s Test Procedure Test Specification Uncertainty Test Result Test Photo Band Edge Test Equipment Test Setup s Test Procedure Test Specification Uncertainty Test Result Occupied Bandwidth Test Equipment Test Setup Page: 3 of 8

4 6.3. s Test Specification Uncertainty Test Result Power Density Test Equipment Test Setup s Test Specification Uncertainty Test Result ttachement EUT Photograph Page: 4 of 8

5 . General Information.. EUT Description Product Name Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Trade Name WLTOP Model No. Tablet: RCK-T7, RCK-T7S; Dongle: RCK-T7R, RCK-T7RS Frequency Range 242~2479MHz Channel Number 78 Type of Modulation Direct Sequence Spread Spectrum (DSSS) ntenna Gain -.5dBi (Tablet) -3.67dBi (Dongle) Channel Control uto ntenna Type Soldered on PCB Component USB Cable Shielded,.5m, two ferrite cores bonded. Working Frequency of Each Channel Channel Frequency Channel Frequency Channel Frequency Channel Frequency Channel 242 MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel 9 24 MHz Channel MHz Channel MHz Channel MHz Channel 24 MHz Channel MHz Channel MHz Channel MHz Channel 242 MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Channel MHz Page: 5 of 8

6 Note:. This device is a Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 included a 2.4GHz receiving function, and 2.4GHz transmitting function. 2. These tests were conducted on a sample of the equipment for the purpose of demonstrating compliance with Part 5 Subpart C Paragraph for spread spectrum devices. 3. Regards to the frequency band operation; the highest rate that was included the lowest middle and highest frequency of channel were selected to perform the test, and then shown on this report. 4. This device is a composite device in accordance with Part 5 regulations. The function receiving was measured and made a test report that the report number is 74H5-RFUSPV2 under Declaration of Conformity. Page: 6 of 8

7 .3. Test Mode QuieTek has verified the construction and function in typical operation. ll the test modes were carried out with the EUT in normal operation, which was shown in this test report and defined as: Pre-Test Mode EMI Final Test Mode TX Mode : Transmit (Tablet) Mode 2: Transmit (Dongle) Mode : Transmit (Tablet) Mode 2: Transmit (Dongle) Page: 8 of 8

8 .4. Tested System Details The types for all equipments, plus descriptions of all cables used in the tested system (including inserted cards) are: Test Mode Mode : Transmit (Tablet) Product Manufacturer Model No. Serial No. FCC ID Power Cord PC HP DTPC27 SG2295 DoC Non-shielded,.8m 2 Monitor CHI MEI 7E-9 3UC2955S249 DoC Non-shielded,.8m 3 Modem CEEX DM DoC Non-shielded,.6m 4 Walkman IW US-J22 I22 DoC -- 5 Modem CEEX DM DoC Non-shielded,.6m 6 Speaker Polk udio 25 N/ DoC -- 7 Mouse Logitech M-SBF83 HC DoC -- 8 Keyboard CER 63-TW2C N/ DoC -- 9 Printer HP C2642 MY75LD2XN DoC Non-shielded,.7m PEN Electromagneti M3-2 N/ DoC -- c induction pen Test Mode Mode 2: Transmit (Dongle) Product Manufacturer Model No. Serial No. FCC ID Power Cord PC HP DTPC27 SG2295 DoC Non-shielded,.8m 2 Monitor CHI MEI 7E-9 3UC2955S249 DoC Non-shielded,.8m 3 Modem CEEX DM DoC Non-shielded,.6m 4 Walkman IW US-J22 I22 DoC -- 5 Modem CEEX DM DoC Non-shielded,.6m 6 Speaker Polk udio 25 N/ DoC -- 7 Mouse Logitech M-SBF83 HC52284 DoC -- 8 Mouse Logitech M-SBF83 HC DoC -- 9 Keyboard CER 63-TW2C N/ DoC -- Printer HP C2642 MY75LD2XN DoC Non-shielded,.7m Page: 9 of 8

9 .5. Configuration of tested System Test Mode Mode : Transmit (Tablet) B Connection Diagram Monitor(2) PC () EUT Doagle (EUT) C Tablet (EUT) PEN Printer(9) I H G E D F Keyboard(8) Mouse(7) Speaker(6) Modem(5) Walkman(4) Modem(3) Signal Cable Type Signal cable Description Printer Cable Shielded,.2m B VG Cable Shielded,.8m, two ferrite cores bonded. C USB Cable Shielded,.5m, two ferrite cores bonded. D Modem Cable Shielded,.5m E Walkman Cable Non-Shielded,.6m F Modem Cable Shielded,.5m G Speaker Cable Non-Shielded,.2m H Mouse Cable Non-Shielded,.8m I Keyboard Cable Shielded,.5m Page: of 8

10 Test Mode Mode 2: Transmit (Dongle) B Connection Diagram Monitor(2) PC () EUT C Doagle (EUT) Printer() I H J F E D G Keyboard(9) Mouse(8) Mouse(7) Speaker(6) Modem(5) Walkman(4) Modem(3) Signal Cable Type Signal cable Description Printer Cable Shielded,.2m B VG Cable Shielded,.8m, two ferrite cores bonded. C USB Cable Shielded,.5m, two ferrite cores bonded. D Modem Cable Shielded,.5m E Walkman Cable Non-Shielded,.6m F Modem Cable Shielded,.5m G Speaker Cable Non-Shielded,.2m H Mouse Cable Non-Shielded,.8m I Keyboard Cable Shielded,.5m J Mouse Cable Shielded,.m Page: of 8

11 .6. EUT Exercise Software Setup the EUT and simulators as shown on.5 2 Turn on the power of all equipment. 3 Notebook PC reads data from disk. 4 Data will be transmitting through EUT. 5 The transmitting status will be shown on the monitor. 6 Repeat the above procedure (4) to (5) Page: 2 of 8

12 .7. Test Facility mbient conditions in the laboratory: Items Test Item Required (IEC 68-) ctual Temperature ( C) FCC PRT 5 C 5.27 Humidity (%RH) Conducted Emission Barometric pressure (mbar) Temperature ( C) FCC PRT 5 C Humidity (%RH) Band Edge (DSSS) Barometric pressure (mbar) Temperature ( C) FCC PRT 5 C Humidity (%RH) Occupied Bandwidth (DSSS) Barometric pressure (mbar) Temperature ( C) FCC PRT 5 C Humidity (%RH) Peak Power Output (DSSS) Barometric pressure (mbar) Temperature ( C) FCC PRT 5 C Humidity (%RH) Power Density (DSSS) Barometric pressure (mbar) Temperature ( C) FCC PRT 5 C Humidity (%RH) Radiated Emission (DSSS) Barometric pressure (mbar) Site Description: January 24, 25 File on Federal Communications Commission Laboratory Division 7435 Oakland Mills Road Columbia, MD 246 Registration Number: Site Name: Site ddress: ccredited by CNL ccreditation Number: 33 Effective through: September 27, 27 ccredited by NVLP NVLP Lab Code: Effective through: September 3, 27 Quietek Corporation No.75-, Wang-Yeh Valley, Yung-Hsing, Chiung-Lin, Hsin-Chu County, Taiwan, R.O.C. TEL : / FX : service@quietek.com 33 ILC MR Page: 3 of 8

13 2. Peak Power Output 2.. Test Equipment The following test equipment are used during the test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Spectrum nalyzer R&S FSP/ 5 Oct., 26 2 No. OTS Sep., 26 Note: ll equipment upon which need to calibrated are with calibration period of year Test Setup EUT RF Cable SM Connecter Spectrum nalyzer 2.3. s The maximum peak power shall be less Watt Test Specification ccording to FCC CFR Title 47 Part 5 Subpart C Section 5.247: Uncertainty The measurement uncertainty is defined as ±.27 db. Page: 4 of 8

14 2.6. Test Result Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Peak Power Output Test Mode Mode : Transmit (Tablet) Date of Test 27/4/2 Test Site No. OTS Channel No. Frequency Measure Level (MHz) (dbm) (dbm) Result Watt= 3 dbm Pass Watt= 3 dbm Pass Watt= 3 dbm Pass Channel Channel 38 Ref 2 dbm * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] dbm GHz Ref 2 dbm * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] dbm GHz PK VIEW PK VIEW Center 2.42 GHz 5 MHz/ Span 5 MHz PRN Tx Channel Bandwidth 2 MHz Power -.59 dbm Center 2.44 GHz 5 MHz/ Span 5 MHz PRN Tx Channel Bandwidth 2 MHz Power -.39 dbm Date: 2.PR.27 4:48:4 Date: 2.PR.27 4:5:34 Channel 79 Ref 2 dbm * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] -4.6 dbm GHz PK VIEW Center GHz 5 MHz/ Span 5 MHz PRN Tx Channel Bandwidth 2 MHz Power -.73 dbm Date: 2.PR.27 4:53:48 Page: 5 of 8

15 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Peak Power Output Test Mode Mode 2: Transmit (Dongle) Date of Test 27/4/2 Test Site No. OTS Channel No. Frequency Measure Level (MHz) (dbm) (dbm) Result Watt= 3 dbm Pass Watt= 3 dbm Pass Watt= 3 dbm Pass Channel Channel 38 Ref 2 dbm - PK * VIEW -2 * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] -.78 dbm GHz Ref 2 dbm - PK * VIEW -2 * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] dbm GHz * Center 2.42 GHz 5 MHz/ Span 5 MHz PRN Center 2.44 GHz 5 MHz/ Span 5 MHz PRN Tx Channel Bandwidth 2 MHz Power dbm Tx Channel Bandwidth 2 MHz Power -.6 dbm Date: 2.PR.27 5:3:25 Date: 2.PR.27 5:5: Channel 79 Ref 2 dbm * tt 3 db * RBW MHz * VBW MHz * SWT 5 ms Marker [T ] -2.9 dbm GHz PK VIEW Center GHz 5 MHz/ Span 5 MHz PRN Tx Channel Bandwidth 2 MHz Power dbm Date: 2.PR.27 5:7:8 Page: 6 of 8

16 3. Conducted Emission 3.. Test Equipment The following test equipment are used during the test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Remark Test Receiver R & S ESCS 3/825442/8 Sep., 26 2 rtificial Mains Network R & S ENV42/8484/ Feb., 27 Peripherals 3 LISN R & S ESH3-Z5/825562/2 Feb., 27 EUT 4 Pulse er R & S ESH3-Z2/ Feb., 27 5 No.2 Shielded Room N/ Note: ll equipment upon which need to calibrated are with calibration period of year Test Setup Page: 7 of 8

17 3.3. s FCC Part 5 Subpart C Paragraph 5.27 s Frequency MHz QP V Remarks : In the above table, the tighter limit applies at the band edges Test Procedure The EUT and simulators are connected to the main power through a line impedance stabilization network (L.I.S.N.). This provides a 5 ohm /5uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN that provides a 5ohm/5uH coupling impedance with 5ohm termination. (Please refers to the block diagram of the test setup and photographs.) Both sides of.c. line are checked for maximum conducted interference. In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to NSI C63.4: 23 on conducted measurement. Conducted emissions were invested over the frequency range from.5mhz to 3MHz using a receiver bandwidth of 9kHz Test Specification ccording to FCC Part 5 Subpart C Paragraph 5.27: Uncertainty The measurement uncertainty is defined as ± 2.26 db. Page: 8 of 8

18 3.7. Test Result Site : QuieTek Shielding Room2 Time : 26/4/9-9:39 : CISPR_B_M_QP Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) * QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 9 of 8

19 Site : QuieTek Shielding Room2 Time : 26/4/9-9:39 : CISPR_B_M_V Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) * VERGE VERGE VERGE VERGE VERGE VERGE Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 2 of 8

20 Site : QuieTek Shielding Room2 Time : 26/4/9-9:44 : CISPR_B_M_QP Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line2 Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) * QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 2 of 8

21 Site : QuieTek Shielding Room2 Time : 26/4/9-9:44 : CISPR_B_M_V Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line2 Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) * VERGE VERGE VERGE VERGE VERGE VERGE Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 22 of 8

22 Site : QuieTek Shielding Room2 Time : 26/4/9-2: : CISPR_B_M_QP Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) QUSIPEK QUSIPEK QUSIPEK QUSIPEK 5 * QUSIPEK QUSIPEK Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 23 of 8

23 Site : QuieTek Shielding Room2 Time : 26/4/9-2: : CISPR_B_M_V Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) VERGE VERGE 3 * VERGE VERGE VERGE VERGE Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 24 of 8

24 Site : QuieTek Shielding Room2 Time : 26/4/9-2:4 : CISPR_B_M_QP Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line2 Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) * QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK QUSIPEK Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 25 of 8

25 Site : QuieTek Shielding Room2 Time : 26/4/9-2:4 : CISPR_B_M_V Margin : EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : SR3_LISN(6) - Line2 Tablet Receiver X86/X86 Power : C 2V/6Hz Note : Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Detector Type (MHz) VERGE 2 * VERGE VERGE VERGE VERGE VERGE Note:. ll Reading Levels are Quasi-Peak and average value. 2. " * ", means this data is the worst emission level. 3.Measurement Level = Reading Level + Correct Factor Page: 26 of 8

26 4. Radiated Emission 4.. Test Equipment The following test equipment are used during the test: Item Equipment Manufacturer Model No. / Serial No. Last Cal. X Test Receiver R & S ESCS 3 / /7 Jan., 27 2 X Spectrum nalyzer dvantest R326C / N/ 3 X Pre-mplifier HP 8447D / N/ 4 X Bilog ntenna Chase CBL62B / 2455 Sep., 26 5 X Spectrum nalyzer R & S FSP4 / 5 ug., 26 6 X Pre-mplifier HP 8449B / 3823 Feb., 27 7 X Horn ntenna Schwarzbeck BBH 92D / BBH92D32 Jul., 26 8 No. OTS Sep., 26 Note:. ll equipments that need to calibrate are with calibration period of year. 2. N/ Ca.Date is used to Pre-test, not final test Test Setup Under GHz Test Setup: bove GHz Test Setup: Page: 29 of 8

27 4.3. s Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 2dB below the level of the fundamental or to the general radiated emission limits in paragraph 5.29, whichever is the lesser attenuation. FCC Part 5 Subpart C Paragraph 5.29 s Frequency MHz 3-88 uv/m dbuv/m bove Remarks :. RF Voltage = 2 log RF Voltage (uv) 2. In the bove Table, the tighter limit applies at the band edges. 3. Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system Test Procedure The EUT and its simulators are placed on a turn table which is.8 meter above ground. The turn table can rotate 36 degrees to determine the position of the maximum emission level. The antenna can move up and down between meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to NSI C63.4:23 on radiated measurement. On any frequency or frequencies below or equal to MHz, the limits shown are based on measuring equipment employing a quasi-peak detector function and on any frequency or frequencies above MHz the radiated limits shown are based upon the use of measurement instrumentation employing an average detector function. When average radiated emission measurement are included emission measurement below MHz, there also is a limit on the radio frequency emissions, as measured using instrumentation with a peak detector function, corresponding to 2 db above the maximum permitted average limit. The bandwidth below GHz setting on the field strength meter is 2 khz and above GHz is MHz Test Specification ccording to FCC Part 5 Subpart C Paragraph 5.247: Uncertainty The measurement uncertainty 3MHz GHz as ±3.9dB GHz 26.5Ghz as ±3.9dB Page: 3 of 8

28 4.7. Test Result 3MHz-GHz Spurious: Site : CB3 Time : 27/4/9-3:56 : FCC_CLSS_B_3M_QP Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_3-G(265) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Detector Type Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak 6 * Quasi-Peak Note:. ll Reading Levels are Quasi-Peak value. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. Page: 3 of 8

29 Site : Site Time : 27/4/9-3:57 : FCC_CLSS_B_3M_QP Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_3-G(265) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Detector Type * Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Note:. ll Reading Levels are Quasi-Peak value. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. Page: 32 of 8

30 Site : Site Time : 27/4/9-3:59 : FCC_CLSS_B_3M_QP Margin : 6 EUT : : Wireless Tablet Receiver X86 Power : C 2V/6Hz Probe : FCC_RF_3-G(265) - HORIZONTL Note : TX-39 Mode 2: Transmit (Dongle) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Detector Type Quasi-Peak Quasi-Peak Quasi-Peak 4 * Quasi-Peak Quasi-Peak Quasi-Peak Note:. ll Reading Levels are Quasi-Peak value. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. Page: 33 of 8

31 Site : Site Time : 27/4/9-4: : FCC_CLSS_B_3M_QP Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_3-G(265) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode 2: Transmit (Dongle) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Detector Type Quasi-Peak 2 * Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Quasi-Peak Note:. ll Reading Levels are Quasi-Peak value. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. Page: 34 of 8

32 Harmonic & Spurious: Site : Site Time : 27/4/2-4:59 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX- Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 35 of 8

33 Site : Site Time : 27/4/2-5: : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX- Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Peak verage Detector Type PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 36 of 8

34 Site : Site Time : 27/4/2-5: : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode : Transmit (Tablet) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 37 of 8

35 Site : Site Time : 27/4/2-5:3 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Peak verage Detector Type PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 38 of 8

36 Site : Site Time : 27/4/2-5:5 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-78 Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Peak verage Detector Type PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 39 of 8

37 Site : Site Time : 27/4/2-5:6 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT :Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-78 Mode : Transmit (Tablet) Frequency (MHz) Correct Factor Reading Level Measure Level Margin Peak verage Detector Type PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 4 of 8

38 Site : Site Time : 27/4/2-5:6 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX- Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 4 of 8

39 Site : Site Time : 27/4/2-5:7 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX- Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 42 of 8

40 Site : Site Time : 27/4/2-5:9 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 43 of 8

41 Site : Site Time : 27/4/2-5:2 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-39 Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 44 of 8

42 Site : Site Time : 27/4/2-5:2 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - HORIZONTL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-78 Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK PEK 4 * PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 45 of 8

43 Site : Site Time : 27/4/2-5:22 : FCC_SpartC_5.247_H_3M_PK Margin : 6 EUT : Tablet: Wireless Tablet X86/X86; Dongle: Wireless Probe : FCC_RF_G-8G(25-3) - VERTICL Tablet Receiver X86/X86 Power : C 2V/6Hz Note : TX-78 Mode 2: Transmit (Dongle) Frequency Correct Factor Reading Level Measure Level Margin Peak verage Detector Type (MHz) PEK PEK 3 * PEK PEK Note:. ll Readings below GHz are Quasi-Peak, above are performed with peak and/or average measurements as necessary. 2. *, means this data is the worst emission level. 3. Measurement Level = Reading Level + Correct Factor. 4. The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 46 of 8

44 4.8. Test Photo Test Mode : Mode : Transmit (Tablet) Description: Front View of Radiated Emission Test Setup (Bi-Log) Test Mode : Mode : Transmit (Tablet) Description: Back View of Radiated Emission Test Setup (Bi-Log) Page: 47 of 8

45 Test Mode : Mode : Transmit (Tablet) Description: Front View of Radiated Emission Test Setup (Horn) Page: 48 of 8

46 5. Band Edge 5.. Test Equipment The following test equipment are used during the test: RF Conducted Measurement: Item Equipment Manufacturer Model No. / Serial No. Last Cal. Spectrum nalyzer R & S FSP / 56 Mar., 27 2 No. OTS Sep., 26 RF Radiated Measurement: Item Equipment Manufacturer Model No. / Serial No. Last Cal. X Spectrum nalyzer R & S FSP4 / 5 ug., 26 2 X Pre-mplifier HP 8449B / 3823 Feb., 27 3 Loop ntenna R & S HFH2-Z2 / /4 Sep., 26 4 BiconiLog ntenna Schwarzbeck VULB 966 / 6 Sep., 26 5 Bilog ntenna Chase CBL62B / 2455 Sep., 26 6 X Horn ntenna Schwarzbeck BBH 92D / BBH92D32 Sep., 26 7 No. OTS Sep., 26 Note:. ll equipments that need to calibrate are with calibration period of year. 2. Mark X test instruments are used to measure the final test results. Page: 5 of 8

47 5.2. Test Setup RF Conducted Measurement: RF Radiated Measurement: 5.3. s In any khz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 2 db below that in the khz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. ttenuation below the general limits specified in Section 5.29(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in Section 5.25(a), must also comply with the radiated emission limits specified in Section 5.29(a) (see Section 5.25(c)). Page: 52 of 8

48 5.4. Test Procedure The EUT and its simulators are placed on a turn table which is.8 meter above ground. The turn table can rotate 36 degrees to determine the position of the maximum emission level. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. The antenna can move up and down between meter and 4 meters to find out the maximum emission level. Both horizontal and vertical polarization of the antenna are set on measurement. In order to find the maximum emission, all of the interface cables must be manipulated according to NSI C63.4:23 on radiated measurement. The bandwidth below GHz setting on the field strength meter is 2 khz, above GHz are MHz Test Specification ccording to FCC Part 5 Subpart C Paragraph 5.247: Uncertainty The measurement uncertainty Conducted is defined as ±.27dB Radiated is defined as ± 3.9dB Page: 53 of 8

49 5.7. Test Result Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode : Transmit (Tablet) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (Peak Detector) Reading Probe Cable Emission Frequency Channel No. Level Factor Loss Level (MHz) (db/m) Peak verage Result (Horizontal) Pass (Vertical) Pass Horizontal Marker 4 [T] RBW MHz RF tt db Vertical Marker 4 [T] RBW MHz RF tt db Ref Lvl db V VBW MHz Ref Lvl db V VBW MHz 97 db V GHz SWT 2 ms Unit db V 97 db V GHz SWT 2 ms Unit db V [T] db V GHz [T] db V GHz [T] 5.77 db V [T] 6.67 db V GHz 2 [T] 27.6 db V GHz 2 [T] 26.5 db V 2.3 GHz 2.3 GHz 7 3 [T] db V 7 3 [T] db V VIEW 2.4 GHz IN M VIEW 2.4 GHz IN M FCC SpartC Margin -3 ETSI_3328 Margin -3 Start 2.35 GHz MHz/ Stop GHz Start 2.35 GHz 2. MHz/ Stop GHz Date: 9.PR.27 :25:4 Date: 8.PR.27 2:3:57 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 54 of 8

50 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode : Transmit (Tablet) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (verage Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result (Horizontal) Pass (Vertical) Pass Horizontal Vertical Marker 4 [T] RBW MHz RF tt db Marker 4 [T] RBW MHz RF tt db Ref Lvl 6.6 db V VBW Hz Ref Lvl 5.23 db V VBW Hz 97 db V GHz SWT 27 s Unit db V 97 db V GHz SWT 3 s Unit db V [T] 6.6 db V LIMIT CHECK : FILED GHz LINE FCC_SpartCFailed [T] db V 9 4 [T] 5.23 db V LIMIT CHECK : FILED GHz LINE ETSI_332Failed [T] db V GHz 2 [T] 4.59 db V GHz 2 [T] 4.58 db V 2.3 GHz 2.3 GHz 7 3 [T] 6.6 db V 7 3 [T] 8.32 db V 2.4 GHz IN 2.4 GHz IN VIEW M VIEW M FCC SpartC Margin ETSI_3328 Margin -3-3 Start 2.35 GHz MHz/ Stop GHz Start 2.35 GHz 2. MHz/ Stop GHz Date: 9.PR.27 :27:38 Date: 8.PR.27 2:37:47 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 55 of 8

51 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode : Transmit (Tablet) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (Peak Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result 78(Horizontal) Pass 78(Vertical) Pass Marker 4 [T] Horizontal RBW MHz RF tt db Marker 4 [T] Vertical RBW MHz RF tt db Ref Lvl db V VBW MHz Ref Lvl db V VBW MHz 97 db V GHz SWT 2 ms Unit db V 97 db V GHz SWT 2 ms Unit db V [T] db V 4 [T] db V GHz GHz [T] 5.9 db V [T] db V GHz 2 [T] db V GHz 2 [T] 3.49 db V GHz GHz 7 3 [T] db V 7 3 [T] db V 2.5 GHz IN 2.5 GHz IN VIEW M VIEW M ETSI_3328 Margin ETSI_3328 Margin -3-3 Start GHz MHz/ Stop 2.5 GHz Center GHz MHz/ Span MHz Date: 8.PR.27 22:3:23 Date: 8.PR.27 22:52:38 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 56 of 8

52 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode : Transmit (Tablet) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (verage Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result 78(Horizontal) Pass 78(Vertical) Pass Marker 4 [T] Horizontal RBW MHz RF tt db Marker 4 [T] Vertical RBW MHz RF tt db Ref Lvl 5.4 db V VBW Hz Ref Lvl 5.8 db V VBW Hz 97 db V GHz SWT 8.8 s Unit db V 97 db V GHz SWT 8.8 s Unit db V [T] 5.4 db V GHz 9 4 [T] 5.8 db V LIMIT CHECK : PSSED GHz [T] db V [T] db V GHz 2 [T] 5. db V GHz 2 [T] 5. db V GHz GHz 7 3 [T] 5.28 db V 7 3 [T] 5.28 db V 2.5 GHz IN 2.5 GHz IN VIEW M VIEW M 6 6 2M ETSI_3328 Margin ETSI_3328 Margin -3-3 Start GHz MHz/ Stop 2.5 GHz Center GHz MHz/ Span MHz Date: 8.PR.27 22:38:4 Date: 8.PR.27 22:55:46 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 57 of 8

53 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode 2: Transmit (Dongle) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (Peak Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result (Horizontal) Pass (Vertical) Pass Horizontal Vertical Marker 4 [T] RBW MHz RF tt db Marker 4 [T] RBW MHz RF tt db Ref Lvl 3.63 db V VBW MHz Ref Lvl 3.45 db V VBW MHz 97 db V GHz SWT 2 ms Unit db V 97 db V GHz SWT 2 ms Unit db V [T] 3.63 db V 4 [T] 3.45 db V GHz GHz [T] db V [T] 63.2 db V GHz 2 [T] 3. db V GHz 2 [T] db V 2.4 GHz 2.3 GHz 7 3 [T] db V 7 3 [T] 3.43 db V 2.3 GHz IN 2.4 GHz IN VIEW M VIEW M ETSI_3328 Margin ETSI_3328 Margin -3-3 Center GHz MHz/ Span MHz Start 2.35 GHz MHz/ Stop GHz Date: 8.PR.27 23:26:8 Date: 8.PR.27 23:36:57 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 58 of 8

54 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode 2: Transmit (Dongle) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (verage Detector) Reading Probe Cable Emission Frequency Channel No. Level Factor Loss Level (MHz) (db/m) Peak verage Result (Horizontal) Pass (Vertical) Pass Horizontal Marker 4 [T] RBW MHz RF tt db Vertical Marker 4 [T] RBW MHz RF tt db Ref Lvl 5.8 db V VBW Hz Ref Lvl 5.75 db V VBW Hz 97 db V GHz SWT 29 s Unit db V 97 db V GHz SWT 29 s Unit db V [T] 5.8 db V LIMIT CHECK : FILED GHz LINE ETSI_332Failed [T] db V [T] 5.75 db V GHz [T] 6.44 db V GHz 2 [T] 7.68 db V GHz 2 [T] 4.64 db V 2.4 GHz 2.3 GHz 7 3 [T] 4.62 db V 7 3 [T] 8.9 db V VIEW GHz IN M VIEW GHz IN M ETSI_3328 Margin -3 ETSI_3328 Margin Center GHz MHz/ Span MHz Start 2.35 GHz MHz/ Stop GHz Date: 8.PR.27 23:29:25 Date: 8.PR.27 23:39:46 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 59 of 8

55 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode 2: Transmit (Dongle) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (Peak Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result 78(Horizontal) Pass 78(Vertical) Pass Horizontal Vertical Marker 4 [T] RBW MHz RF tt db Marker 4 [T] RBW MHz RF tt db Ref Lvl 29.9 db V VBW MHz Ref Lvl 3.48 db V VBW MHz 97 db V GHz SWT 2 ms Unit db V 97 db V GHz SWT 2 ms Unit db V [T] 29.9 db V 4 [T] 3.48 db V GHz GHz [T] db V [T] 6.65 db V GHz 2 [T] 27.4 db V GHz 2 [T] 28.3 db V GHz GHz 7 3 [T] 28.6 db V 7 3 [T] db V VIEW 2.5 GHz IN M VIEW 2.5 GHz IN M ETSI_3328 Margin ETSI_3328 Margin -3-3 Start GHz MHz/ Stop 2.5 GHz Start GHz MHz/ Stop 2.5 GHz Date: 8.PR.27 23:47:55 Date: 9.PR.27 :3:36 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 6 of 8

56 Product Tablet: Wireless Tablet X86/X86; Dongle: Wireless Tablet Receiver X86/X86 Test Item Band Edge Test Mode Mode 2: Transmit (Dongle) Date of Test 26/4/9 Test Site No. OTS RF Radiated Measurement: (verage Detector) Channel No. Frequency (MHz) Reading Level Probe Factor (db/m) Cable Loss Emission Level Peak verage Result 78(Horizontal) Pass 78(Vertical) Pass Marker [T] Horizontal RBW MHz RF tt db Marker 4 [T] Vertical RBW MHz RF tt db Ref Lvl db V VBW Hz Ref Lvl 5.26 db V VBW Hz 97 db V GHz SWT 8.8 s Unit db V 97 db V GHz SWT 8.8 s Unit db V [T] db V LIMIT CHECK : FILED GHz LINE ETSI_332Failed 2 [T] 5. db V 9 4 [T] 5.26 db V LIMIT CHECK : FILED GHz LINE ETSI_332Failed [T] 58.9 db V GHz 3 [T] 5.33 db V GHz 2 [T] 5.4 db V 2.5 GHz GHz 7 4 [T] 5.6 db V 7 3 [T] 5.3 db V GHz IN 2.5 GHz IN 6 VIEW M 6 VIEW M ETSI_3328 Margin ETSI_3328 Margin -3-3 Start GHz MHz/ Stop 2.5 GHz Start GHz MHz/ Stop 2.5 GHz Date: 8.PR.27 23:54:2 Date: 9.PR.27 :8:2 Note: The average measurement was not performed when the peak measured data under the limit of average detection. If the readings given are average, peak measurement should also be supplied. Page: 6 of 8