Quick Start Guide. Step 1: Disconnect all alternate video sources to the screen. Step 3: Connect Barfly computer to scaler

Transcription

1 Quick Start Guide Rev. 01 May 2010 This guide is intended as a brief overview of the Barfly installation process. For a complete copy of the Barfly Installation and Setup Guide (p/n ), visit the TouchTunes/Barfly Dashboard at Before performing these procedures, ensure that AC power is switched off. Step 1: Disconnect all alternate video sources to the screen. See page 9 of Installation and Setup Guide. The scaler accepts only component and composite inputs. If your video source has only an RF (coaxial) output, you will require a tuner and the necessary adapter cables (included with kit EK3). Step 3: Connect Barfly computer to scaler See page 11 of Installation and Setup Guide. Satellite receiver Cable box DVI to Step 2: Connect video source to scaler See page 11 of Installation and Setup Guide. Composite - OR - - OR - Barfly computer Connect the and outputs from the Barfly computer to their respective ports on the scaler * 1. Note: port on Barfly computer is located adjacent to the AC power inlet. Composite Step 4: Connect Barfly computer to the Internet See page 15 of Installation and Setup Guide. Modem or Router to DVI cable to DVI cable Barfly computer - *OR - RF (coax.) *Special case; tuner required. does not accept coax input. 1. Ensure that the venue s router or modem has a working Internet connection. 2. Connect the network cable coming from the modem or router to the network port on the back of the computer. 1 of 7 1. For Dell Optiplex computer, use cable instead of DVI to.

2 Step 5: Connect scaler to display See page 17 of the Installation and Setup Guide. The following are some common configurations. video DVI to BARFLY Computer RS-232 Kit SK1 Configuration 1: Barfly system located at the * 1 CV-57BB (TX) Extender over CAT5 CV-57BB (RX) Extender over CAT5 CAT5 Kit EK8 Front Rear Rear Front video DVI to BARFLY Computer RS-232 Kit SK1 Configuration 2: Barfly system remote to * 1 1. For Dell Optiplex computer, use cable instead of DVI to. 2 of 7

3 BARFLY computer DVI to CAT5 Kit EK1 CV-927D and Extender Over CAT5 Part of Kit SK1 Configuration 3: Barfly system remote to scaler at * 1 1. For Dell Optiplex computer, use cable instead of DVI to. 3 of 7

4 Kit SK3 SP-5002E 1x2 Distribution Amplifier From Fig. 1, 2 or 3 as needed CV-57BB (TX) Extender over CAT5 CV-57BB (RX) Extender over CAT5 CAT5 Kit EK8 Front Rear Rear Front Configuration 4:Dual screen single scaler Kit EK2 CV-509 /DVI to / Converter From Fig. 1, 2 or 3 as needed -component breakout cable Front Rear Configuration 5: to component conversion 4 of 7

5 Kit EK10 CV-105 DVI & Audio to Converter Audio From Fig. 1, 2 or 3 as needed DVI Front Rear NOTE: Audio signal comes from video source not scaler. Configuration 6: DVI and audio to conversion video Splitter Part of Kit SK2 BARFLY computer DVI to Part of Kit SK2 USB to adapter cable video Kit SK1 Configuration 7: Dual scaler * 1 1. For Dell Optiplex computer, use cable instead of DVI to, and two (2) cables instead of USB to. 5 of 7

6 Step 6: Install the Hard Drive See page 24 of the Installation and Setup Guide. 1. Ensure that the Barfly computer is powered OFF. 2. Align the hard drive tray with its slot on the front panel of the computer. 3. Insert the hard drive tray in the slot and then gently push the tray in until it is completely seated. 1. Connect your laptop computer and the Barfly computer to available LAN ports on the router. Router Operator s portable computer Barfly Computer To scaler 2. Open a Web browser and establish a connection to the Barfly computer by typing the IP address into the address field, concatenated with the string /operator. Enter operator and flyonthewall for username and password, respectively, when prompted. 4. Using your fingers, push in and then tighten the thumb screw (clockwise) on the hard drive tray until the thumb screw is securely tightened. Step 7: Power up the scaler and computer See page 26 of the Installation and Setup Guide. 1. Power up the scaler by connecting the AC adaptor to the 5V DC inlet on the rear panel and to a properly grounded electrical outlet. 5V DC inlet Main power switch 2. Power up the computer and allow it the time necessary to boot up. Step 8: Calibrate the scaler See page 27 of the Installation and Setup Guide. 3. When the welcome screen displays, press Start to begin the calibration process and follow the on-screen instructions. Contacting TouchTunes/Barfly Support If you need help with or have questions about this document, contact TouchTunes by: Using the links on the Contacts page on the TouchTunes Dashboard at Calling TouchTunes 24/7 Service Hotline at , and selecting option 2 for Barfly. To help us assist you more effectively with problem reports, the following information may be required when contacting TouchTunes Support: Venue you are calling about that has the Barfly system. Thorough problem description. Time the problem started. 6 of 7

7 Any environmental issues that may have caused the problem. Actions already taken to attempt a correction. TouchTunes Interactive Networks, Inc. 400 Sainte Croix Avenue, Suite 200 E Montreal, Quebec, Canada, H4N 3L4 TouchTunes Interactive Networks, Inc Salt Creek Lane, Suite 100 Arlington Heights, IL USA Technical Support of 7