SlimLine. Compliant to DO-160D Document # Rev H. www. rosenaviation.com. www. rosenaviation.com

Transcription

1 10.4 Model DISPLAY SlimLine Number 1042 www. rosenaviation.com OEM SALES 8 Shackleford Plaza, Suite 201 Little Rock, AR Fax (501) Document # Rev H CORPORATE OFFICE 1020 Owen Loop South Eugene, OR Fax (541) DEALER & OPERATOR SALES 1121 Warren Ave, Suite 240 Downers Grove, IL Fax (630) Compliant to DO-160D www. rosenaviation.com

2 Table of Contents Introduction and Display Overview... 3 Display Diagram... 4 Pinouts... 6 Operation... 9 Specifications DO-160D Test MatrixDO-160D Test Matrix Troubleshooting Disclaimer Rosen Aviation Displays 1

3 1020 Owen Loop South Eugene OR

4 Introduction and Display Overview Introduction and Display Overview Welcome to the 1042 Technical Manual for the 10.4" LCD monitor This manual provides an overview of display details including: Pinouts Installation Operation Troubleshooting Specifications The 1042 base model includes the following features: 10.4" Diagonal Viewing Area NTSC/PAL/SECAM/RS170 (Composite Video) 640 x 480 Screen Resolution (VGA ) On Screen Display (OSD) Functions Status LED 28 Volt Operation Front Panel Menu Operation Rosen Aviation Displays 3

5 Display Diagram Display Diagram (Inches) (Shown) 10.4 LCD 4

6 Display Diagram (Shown) Rosen Aviation Displays 5

7 Pinouts Pinouts Slimline Base Receptacle Model & Connector: 9 Pin Male D-Subminiature Positronic SDM0000Z Mate: 9 Pin Female D-Subminiature Positronic SD9F0000X Pin # Monitor Signal 1 Reserved 2 +28V DC 3 DC Return 4 *Conn to pin 5 5 *Conn to pin 4 6 Reserved 7 Video Signal Input 8 Video Ground 9 Reserved Note: Pins 4 & 5 are internally connected. Slimline Base Receptacle Model Video Connector: BNC Plug, AMP Power Connector: Female 3 pin,.062" Molex Mating Video Connector: BNC Jack Mating Power Connector: Molex Mating Power Contact: Molex Pin # BNC signal BNC shield Molex 1 Molex 2 Molex 3 Monitor Signal Video Signal Video Return +28V DC DC Return Reserved Note: Base Receptacles sold separately LCD 6

8 Pinouts Pinouts Main Interface Signal The input connector on this display is a Positronic 0DD26M0000Z standard density D-sub) Recommended mating connector: Positronic : P/N 0DD26F0000X. Note: Mating connector kit provided MATING CONNECTOR LOADING VIEW 1. Red 2. Green 3. Blue 4. Reserved 5. Reserved 6. Red Return 7. Green Return 8. Blue Return 9. Reserved 10. Computer Ground 11. Power on / off 12. Reserved 13. Horizontal Sync 14. Vertical Sync Volt DC (+) 16. Reserved 17. Reserved 18. Reserved 19. Reserved 20. Video Shield 21. S Video Ground 22. Y-Signal 23. C-Signal 24. Video Signal Input (NTSC, PAL) Volt DC (+) 26. Power Supply Return DC (-) Rosen Aviation Displays 7

9 Pinouts Pinouts External Control Interface ( ) The external control interface is a 9-pin standard density D- subminiature male connector. Pin 1. Gnd Control Signal 2. Reserved 3. Menu 4. Adjust + 5. Select + 6. Reserved 7. Reserved 8. Adjust- 9. Select LCD 8

10 Operation Ensure that when plugging the arm into the base receptacle, the arm s slot faces toward the release button (as shown) and the connection is not forced. Operation Rosen Aviation Displays 9

11 Operation Operation (Cont) Utilities : User Setting : User Timeout DPMS : adjust the OSD menu timeout period in a step of 5 seconds : Disable / Enable the DPMS function Auto Source Select : Off - Disable auto source select function. Low - Auto source select enable ONLY in power up. High - Auto source select ALWAYS enable. Gamma : 1.0 (Default setting) OSD Setting : OSD Horz Position : move the OSD menu horizontally OSD Vert Position : move the OSD menu vertically OSD Background : Translucent / Opaque OSD Rotate : Normal / Rotate Freeze Frame : Freeze the image (use + button) Zoom : Zoom level : enable the zoom in function on the image displayed. Use + button to zoom in the image. e - button to decrease the zoomed image. Horizontal Pan : Vertical Pan : Us Direct Access #1: Define the hot key function ( + and - ) for one of the following adjustments : Brightness / Contrast / Volume / Freeze / Zoom / Video Source* / PIP Direct Access #2: Define the hot key function ( SEL UP and SEL DN ) for one of the following adjustments : Brightness / Contrast / Volume / Freeze / Zoom / Video Source* / PIP Display Orientation : Normal / Horizontal Inverse / Vertical Inverse / Inverse Calibrate RGB Gain : Color Calibration (DISPLAYED IN PC MODE ONLY) Load Factory Defaults : Recall factory default settings. * By pressing the hot key, the source is in sequence of Analog RGB/Composite Video/S- Video/Component Video LCD 10

12 Operation Operation (Cont) Volume : Adjust the audio volume level (functions only if the audio add-on installed) Exit menu (V1.00) The OSD settings chosen will be stored in memory. The OSD menu can be cleared from the screen by moving the selection bar to the EXIT icon pressing the + button otherwise it will automatically clear after a few seconds (time-out period) of non-use. Rosen Aviation Displays 11

13 Specifications Specifications LCD Performance Screen Resolution (pixels) Display Viewing Area 640 w x 480 h 8.31 x 6.24 In Viewing Angle ( At contrast ratio 10:1 ) Horizontal ±70º Vertical Contrast Ratio Backlight Lamp Life (hours) 45º up 55º down 300:1 (typical) 50,000 hrs Screen Brightness 350 cd/m 2 Mechanical Packaging Weight ( Monitor only) 5.75 lbs.(max) Power Requirements 28VDC 700 ma Nominal Video Performance Video Standards NTSC, PAL, SECAM, RS-170 Video input 1V peak-to-peak, 75 Ohms Operating Temperature 0ºC - 50ºC Warranty 2yr 10.4 LCD 12

14 DO-160 Test Matrix 10.4 Monitor DO-160D Test Matrix Section Description Category 4 Temp & Alt A1 5 Temp Variation C 6 Humidity A 7 Op Shock & Crash Safety B 8 Vibration SB 9 Explosion Proofness X 10 Waterproofness X 11 Fluids Susceptibility X 12 Sand & Dust X 13 Fungus Resistance X 14 Salt Spray X 15 Magnetic Effect X 16 Power Input A 17 Voltage Spike B 18 AF Cond Suscept Pwr A 19 Induced Signal Suscept Z 20 RF Suscept (Cond&Rad) TTX 21 Emission of RF Energy M 22 Lightning Induced Trans X 23 Lightning Direct Effects X 24 Icing X 25 Electrostatic Discharge X X= Not Tested Technical Support For field support or to order parts, contact Rosen Aviation Displays at: or visit us at: Rosen Aviation Displays 13

15 Troubleshooting Troubleshooting PROBLEM POSSIBLE SOLUTION No Power No Video Verify that the pinout is correct Push and hold the power switch for about one second Verify that the monitor is getting power and the pinout is correct Verify that the video source is on and has a tape or DVD installed Verify signal at monitor end. Use an oscilloscope or another monitor Verify that the monitor is in the right mode setting Screen is Black Screen is Blue Red LED is on Color Needs Adjusting Image is Distorted Verify that the monitor is getting power and the pinout is correct Verify that the video source is on and has a tape or DVD installed Verify all connections Verify signal at monitor end. Use an oscilloscope or another monitor Verify that the pinout is correct Verify that the video source is on and has a tape or DVD installed This indicates that the monitor is powered but is receiving no signal See the Operator's Manual, pg 9 Menus Verify that the pinout is correct Verify that a signal is present and accurate Examine system for pinched or damaged cables Notes Always use an oscilloscope to verify video or RGB signals Always use a multimeter to verify voltages Always check actual results against requirements in the Operator's Manual 10.4 LCD 14

16 Rosen Aviation Displays 15

17 Disclaimer Disclaimer All information, including illustrations, is believed to be reliable. Users and/or installers, however, should independently evaluate the suitability of each product for their application. Rosen makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use or installation. Rosen s only obligations are those in the Rosen Standard Terms and Conditions of Sales for this product, and in no case will Rosen be liable for any incidental, indirect or consequential damages arising from the sale, resale, use or misuse of the product. Specifications are subject to change without notice. Rosen reserves the right to make changes - without notification to buyer - to materials or processing that do not affect compliance with any applicable specifications LCD 16