PT-DZ21K2 S P E C F I L E. 3-Chip DLP Projector. As of August Specifications and appearance are subject to change without notice.

Transcription

1 S P E C F I L E Product Number : Product Name : 3-Chip DLP Projector As of August Specifications and appearance are subject to change without notice. 1/14

2 Specifications Main unit Power supply Power consumption DLP chip Lens Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency Panel size Display method Pixels SDI HDMI/DVI-D/ DIGITAL LINK RGB YPBPR (YCBCR) Video/S-Video V AC, 12 A, 50/60 Hz (3-wire single-phase) 2,060 W (2,100 VA) (0.3 W with STANDBY MODE set to ECO.* 1 9Wwith STANDBY MODE set to NORMAL.), max. 7,031 BTU (without light output: 6,758 BTU ) 24.4 mm (0.96 inches) diagonal (16:10 aspect ratio) DLP chip 3 (R, G, B), DLP projection system 2,304,000 (1,920 1,200) 3, total of 6,912,000 pixels Optional powered zoom/focus es 432 W UHM lamps ( 4) (four lamp system) m (701,000 inches) ( m (70600 inches) with the ET-D75LE8), 16:10 aspect ratio 20,000 lumens (four lamp) 90% 10,000:1 (full on/full off, in dynamic iris 3 mode) 1,920 1,200 pixels (Input signals that exceed this resolution will be converted to 1,920 1,200 pixels.) Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 372 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 2048 x 1080/24p, 2048/1080/24sF Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit): SMPTE ST 372 compliant: /24p, /24sF, 3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 424 compliant: 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1080/50p, 1080/60p, HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 480i, 576i Horizontal: khz, vertical: Hz, dot clock: MHz Horizontal: khz, vertical: Hz, dot clock: 162 MHz or less 480i (525i): fh khz; fv 4 Hz, 576i (625i): fh khz; fv 50 Hz, 480p (525p): fh khz; fv 4 Hz, 576p (625p): fh khz; fv 50 Hz, 720 (750)/60p: fh khz; fv 60 Hz, 720 (750)/50p: fh khz; fv 50 Hz, 1035/60i: fh khz; fv 60 Hz, 1080 (1125)/60i: fh khz; fv 60 Hz, 1080 (1125)/50i: fh khz; fv 50 Hz, 1080/25p: fh khz; fv 25 Hz, 1080/24p: fh 0 khz; fv 24 Hz, 1080/24sF: fh 0 khz; fv 48 Hz, 1080/30p: fh khz; fv 30 Hz, 1080/60p: fh khz; fv 60 Hz, 1080/50p: fh khz; fv 50 Hz fh: khz, fv: 4 Hz [NTSC/NTSC4.43/PAL-M/PAL60] fh: khz, fv: 50 Hz [PAL/PAL-N/SECAM] As of August /14

3 Optical axis shift Vertical Horizontal ±55% (±44% with the, % with the ET-D75LE90) from center of screen, powered ±20% (±15% with the, ±6% with the ET-D75LE90) from center of screen, powered NOTE: Optical axis shift function cannot be operated when used with the ET-D75LE50. Keystone correction range Vertical ±40 (vertical ±22 and horizontal ±15 with the ET-D75LE50, vertical ±28 and horizontal ±15 with the, vertical +5 and horizontal ±15 with the ET-D75LE90) Keystone correction range when using the Vertical ±45, horizontal ±40 optional upgrade kit ET-UK20* 3 (vertical ±40 and horizontal ±40 with the ET-D75LE1/2/10/20, vertical ±28 and horizontal ±15 with the, vertical ±22 and horizontal ±15 with the ET-D75LE5/50) Curved correction range Vertical ±20, horizontal ±15 (vertical ±8 and horizontal ±8 with the ET-D75LE5/50, Installation Terminals SDI IN 1 SDI IN 2 HDMI IN DVI-D IN DIGITAL LINK/LAN RGB 1 IN R, G, B Y, PB, PR (Y, CB, CR) S-Video signal RGB 2 IN R, G, B Y, PB, PR (Y, CB, CR) 3D SYNC 1 IN/OUT 3D SYNC 2 OUT SERIAL IN SERIAL OUT REMOTE 1 IN REMOTE 1 OUT REMOTE 2 IN vertical ±10 and horizontal ±10 with the ) Ceiling/floor, front/rear BNC 1, Dual-link 3G-SDI signal: SMPTE S T 425 compliant (Link 1) Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A) 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant BNC 1, Dual-link 3G-SDI signal: SMPTE S T 425 compliant (Link 2) Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B) 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant HDMI 19-pin 1, Deep Color, compatible with HDCP DVI-D 24-pin 1, DVI 1.0 compliant, HDCP compatible, for single link only RJ-45 Network connection / digital link connection (video/network/serial control) compliant with PJLink (class1),100base-tx, Art-Net compatible Deep Color, compatible with HDCP BNC 5 R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms Y: 1.0 Vp-p, C: Vp-p, 75 ohms D-sub HD 15-pin (female) 1 R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals. Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms BNC 1, 1.0 Vp-p, 75 ohms Input: TTL, high impedance. Output: TTL, max. 10 ma BNC 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 ma D-sub 9-pin (female) 1 for external control (RS-232C compliant) D-sub 9-pin (male) 1 for link control M3 jack 1 for wired remote control M3 jack 1 for link control D-sub 9-pin (female) 1 for external control (parallel) As of August /14

4 Power cord length Cabinet materials Dimensions (W H D): Weight* 6 Operation noise* 2 Operating temperature Operating humidity 3.0 m (9 10 in) Molded plastic * 4 800* 5 mm (24-7/ /32* /2* 5 inches) (without ) Approx. 41 kg (90.4 lbs) (without ) 46 db (quad lamp operation) 0 45 C ( F)* 7 10%80% (no condensation) Remote control unit Power supply Operation range* 8 Dimensions (W H D) Weight 3 V DC (AA/R6 type battery 2) Approx. 30 m (98 5 in) when operated from directly in front of the signal receptor mm (1-7/8 7-5/32 1-3/32 inches) Approx. 150 g (5.3 oz) (including batteries) Supplied accessories Power cord with security lock ( 1) Wireless/wired remote control unit ( 1) Batteries for remote control (AA/R6 type 2) Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software) ( 1) Optional accessories (0.91.1:1) (1.31.7:1) (1.72.4:1) (2.44.7:1) (4.67.4:1) ( :1) (0.7:1) (0.36:1) Lens motor cover Ceiling mount bracket Projector mount bracket Frame Smoke cut filter Upgrade kit Auto sreen adjustment upgrade kit Replacement lamp unit Replacement lamp unit for portrait mode Replacement filter unit ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 ET-D75LE50 ET-D75LE90 ET-D75MC1 ET-PKD520H (for high ceilings) ET-PKD520S (for low ceilings) ET-PKD520B ET-PFD510 ET-SFR510 ET-UK20 ET-CUK10 (except in the United States) ET-LAD520 (one bulb) ET-LAD520F (a set of four bulbs) ET-LAD520P (one bulb) ET-LAD520PF (a set of four bulbs) ET-EMF510 Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. *1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal. *2 Measurement, measuring conditions, and method of notation all comply with ISO international standards. *3 Up to a total of ±55 during simultaneous horizontal and vertical correction. *4 With legs at shortest position. *5 Excluding the optional. *6 Average value (excluding the optional ). May differ depending on models. *7 The operating temperature range is 0 C to 40 C (32 F to 104 F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature range is 0 C to 35 C (32 F to 95 F), and the projector cannot be used in places at high altitude. The operating temperature range is 0 C to 40 C (32 F to 104 F) when the ET-LAD520P/LAD520PF lamp is mounted and the projector is used in portrait configuration. The operating temperature range is 0 C to 35 C (32 F to 95 F) when the FAN CONTROL is set to HIGH ALTITUDE MODE (for altitudes from 1,400 m to 2,700 m (4,593 ft to 8,858 ft) above sea level). When the projector is used with the ET-SFR510 Smoke Cut Filter, the operating temperature range is 0 C to 30 C (32 F to 86 F). *8 Operation range differs depending on environments. As of August /14

5 Dimensions 70 (2-3/4) 800 (31-1/2) 730 (28-3/4) unit : mm (inch) NOTE: This illustration is not drawn to scale. 244 (9-19/32) 244 (9-19/32) 620 (24-13/32) 291 (11-15/32) 177 (6-31/32) 36 (1-13/32) 47 (1-27/32) 608 (23-15/16) Terminals Remote 1 input 2 Remote 1 output 3 Remote 2 input 4 Serial input 5 Serial output D sync 1 input/output 7 3D sync 2 output 8 SDI 1 input 9 SDI 2 input 10 RGB 1 Input 11 RGB 2 input 12 DVI-D input 13 HDMI input 14 LAN/DIGITAL LINK connector As of August /14

6 Standard setting-up position H Upper edge of projected image ø60.5 (2-3/8) * (16-1/2 21-7/32) * 2 (22-1/ /32) *1 When the protrudes to the maximum. 212 mm (8-11/32) with the 125 mm (4-29/32) with the ET-D75LE mm (4-3/4) with the ET-D75LE mm (4-3/4) with the ET-D75LE mm (4-7/8) with the ET-D75LE mm (10) with the ET-D75LE8 203 mm (8) with the ET-D75LE50 Projected image L * (11-23/32) 432 (18) *2 Adjustable in 40 mm (1-9/16) steps. L Lower edge of projected image 157 (6-3/16) H unit : mm (inch) Projected image L 314 (12-3/8) 87.5 (3-7/16) 175 (6-7/8) 87.5 (3-7/16) 157 (6-3/16) NOTE: Illustrations show the projector installed using optional ceiling mount bracket ET-PKD520H/ET-PKD520B and an optional.this illustration is not drawn to scale. Caution: All construction work should be done by a qualified technician. When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or dropping, attach the wire that is included with the projector between the mounting bracket and the ceiling. As of August /14

7 Projection distance for 16:10 aspect ratio screen (/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Screen size (diagonal) [m] / [in] ET-D75LE10 Distance to screen (L) Zoom ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 min. max. min. max. min. max. min. max. min. max. min. max. ET-D75LE50 Unit: meters Height from the edge of screen to center of (H) es Except Fixedfocus 1.78 / / / / / / / / / / / / / / / / Screen size (diagonal) [m] / [in] ET-D75LE10 Distance to screen (L) Zoom ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 min. max. min. max. min. max. min. max. min. max. min. max. ET-D75LE50 Unit: feet Height from the edge of screen to center of (H) es Except Fixedfocus 1.78 / / / / / / / / / / / / / / / / The value for L (distance to screen) varies slightly within ±5% depending on the zoom characteristics. At the shortest projection distance, the zoom characteristics may cause slight image distortion. When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. NOTE: When the ET-D75LE50 is mounted, the optical shift function cannot be used. As of August /14

8 Projection distance for 16:9 aspect ratio screen (/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Screen size (diagonal) [m] / [in] ET-D75LE10 Distance to screen (L) Zoom ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 min. max. min. max. min. max. min. max. min. max. min. max. ET-D75LE50 Unit: meters Height from the edge of screen to center of (H) es Except Fixedfocus 1.78 / / / / / / / / / / / / / / / / Screen size (diagonal) [m] / [in] 1.78 / 70 ET-D75LE10 Distance to screen (L) Zoom ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 min. max. min. max. min. max. min. max. min. max. min. max ET-D75LE Unit: feet Height from the edge of screen to center of (H) es Except Fixedfocus / / / / / / / / / / / / / / / The value for L (distance to screen) varies slightly within ±5% depending on the zoom characteristics. At the shortest projection distance, the zoom characteristics may cause slight image distortion. When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. NOTE: When the ET-D75LE50 is mounted, the optical shift function cannot be used. As of August /14

9 Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 es ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) ET-D75LE50 L (m) = (diagonal screen size in inches) Aspect ratio 16:9 es ET-D75LE10 ET-D75LE20 ET-D75LE30 ET-D75LE40 ET-D75LE8 minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches) ET-D75LE50 L (m) = (diagonal screen size in inches) Distances calculated with the above equations will include slight deviations. As of August /14

10 Chip DLP Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. When the except the is mounted 0.2H H (Width of projected image) 0.2H When the is mounted 0.15H H (Width of projected image) 0.15H 0.55V 0.44V V (Height of projected image) 0.12V 0.12V V (Height of projected image) 0.12V 0.12V 0.55V 0.44V Standard postition of projected image NOTE: Because the ET-D75LE50 is a fixed short-throw, the shift function cannot be used with it. Standard postition of projected image Installable angle Install the projector at an angle within the range shown below. Vertical direction The projector may be installed at a vertical angle of 360. Horizontal direction The projector may be installed at a horizontal angle of ± Vertical direction in portrait mode with the ET-LAD520P/LAD520PF mounted The projector may be installed at a vertical angle of ±15. Horizontal direction in portrait mode with the ET-LAD520P/LAD520PF mounted The projector may be installed at a horizontal angle of ± NOTE: The projector cannot be vertically installed all by itself. Also, the terminal side must face downward when vertically installed. As of August /14

11 List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 khz to 100 khz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,920 1,200 pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution. Display mode NTSC/NTSC4.43/PAL-M/PAL60 PAL/PAL-N/SECAM 480i (525i) 576i (625i) 480i (525i) 576i (625i) 480p (525p) 576p (625p) 720/60p 720/50p 1080/60i 1080/50i 1080/24p 1080/24sF 1080/25p 1080/30p 1080/60p 1080/50p 2K/24p 2K/24sF 2K/24sF 2K/24sF 2K/24sF VGA400 VGA480 SVGA MAC16 XGA MXGA MAC21 Display resolution (dots)* i i i i i i Scanning frequency H V (khz) (khz) (1440) 480i* (1440) 576i* Dot clock frequency (MHz) Format VIDEO/S-VIDEO SDI/RGB/YCBCR HDMI/DVI-D/ HDMI/DVI-D/ RGB/YCBCR SDI/HDMI/DVI-D/ RGB/YPBPR SDI* 3 /HDMI/DVI-D/ RGB/YPBPR 4 SDI* SDI* HDMI/DVI-D/RGB *1 The i appearing after the resolution indicates an interlaced signal. *2 Pixel-Repetition signal (dot clock frequency MHz) only *3 SDI 1 only. *4 For dual-link connection only. As of August /14

12 Display mode MSXGA SXGA SXGA+ WXGA UXGA60 WSXGA WUXGA Display resolution (dots) * * Scanning frequency H V (khz) (khz) Dot clock frequency (MHz) * * Format HDMI/DVI-D/RGB RGB HDMI/DVI-D/RGB RGB * Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking). As of August /14

13 List of compatible 3D signals The 3D signals that can be input to this projector are shown in the table below. Display mode 720/60p 720/50p 1080/60i 1080/50i 1080/24p 1080/24sF 1080/25p 1080/30p 1080/60p 1080/50p VGA480 SVGA XGA MXGA MSXGA SXGA SXGA+ WXGA UXGA60 WSXGA+ WUXGA Display resolution (dots)* 1 i i * 3 * 3 Scanning frequency H V (khz) (khz) Dot clock frequency (MHz) * 3 * HDMI Frame packing Side by side* 2 Top and bottom DVI-D Side by side* 2 Top and bottom Line by line Frame sequential *1 The i appearing after the resolution indicates an interlaced signal. *2 Compatible with half-resolution signals. *3 Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking). As of August /14

14 Display mode 720/60p 720/50p 1080/60i 1080/50i 1080/24p 1080/24sF 1080/25p 1080/30p 1080/60p 1080/50p VGA480 SVGA XGA MXGA MSXGA SXGA SXGA+ WXGA UXGA60 WSXGA+ Display resolution (dots)* 1 i i WUXGA * 4 * 4 * 4 * 4 Scanning frequency H V (khz) (khz) Dot clock frequency (MHz) RGB1/RGB2 Side by side* 2 Top and bottom *1 The i appearing after the resolution indicates an interlaced signal. *2 Compatible with half-resolution signals. *3 SDI 1 only. *4 Compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking). Line by line SDI1/SDI2 Frame Side sequential side* by 2 * 3 Top and bottom * 3 Line by line HDMI & DVI-D Simultaneoutaneoutaneous Simul- Simul- Simultaneous RGB1 & RGB2 SDI1 & SDI2 3G-SDI Level B * 3 As of August /14