Technical operating data

Transcription

1 SubstiTUBE Advanced UO UN ST8AU-1.2m-16W-UN Preliminary Datasheet Innovative LED-lamp, easy and safe to use in CCG and ECG installations as direct retrofit. Energy saving potential of up to 63% by replacing 1.2 m T8 fluorescent tubes. Instant 100% light without flickering. No mercury. Applicable in warehouses, cold storage, supply rooms, corridors, industry, stairways, garages, etc; for applications with high operating hours. Technical operating data Product Color Colortemp. [K] Lum. Flux [lm] Voltage [V] / Frequency [Hz] Input current [A] Power [W] Radiance- Angle [ ] ST8AU-1.2m-16W- 865-UN ST8AU-1.2m-16W- 840-UN Cool Daylight Cool White 6500 K K V 50 / 60 Hz 75 ma 16 W 160 All Data are related to the entire lamp. Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data. Technical Features LED lamp in T8 shape with G13 socket Weight: 375g For operation at magnetic ballast without rewiring Direct Retrofit for CCG / ECG luminaires; replacement of lamp and included starter Extremely robust due to polycarbonate body Powerfactor > 0.9 Up to 50,000 h lifetime Switching cycles > Color Rendering Index (CRI) > 80 Overpower and short circuit protected High color homogeneity RoHS-conformity, no mercury Not dimmable Energy Efficiency Class: A++ ST8AU-1.2m-UN August 2016 Page 1 of 6

2 Minimum / Maximum ratings ST8AU- 1.2m-UN Maximum temperature at Tc test point 75 C Storage temperature Ts Ambient temperature Ta C C Drawings Product l d ST8AU-1.2m-UN 1200 mm 27,3 mm ST8AU-1.2m-UN August 2016 Page 2 of 6

3 Safety and Application notes The SubstiTUBE condition. Advanced UO UN must not be damaged or operated in a damaged When operating with CCG, the included SubstiTUBE Start has to be inserted as well. If the conventional starter is not replaced the SubstiTUBE Advanced will start blinking. Switch off immediately, the SubstiTUBE Advanced UO UN can be damaged! Lamp suitable for 50 Hz or 60 Hz operation Lamp suitable for high frequency operation Lamp not suitable for emergency operation Not usable in luminaires with serial lamp connection i.e. more than one tube at one magnetic ballast (tandem circuitry). The SubstiTUBE Advanced UO UN emits light only with a limited angle, not like a fluorescent tube with 360 output. The temperature range of this lamp is more restricted. SubstiTUBE Advanced UO UN is compatible with ECGs of various brand manufacturers. For further information regarding the tested ECGs a compatibility list can be found on the following page. The compatibility list is based upon testing conducted by the manufacturer in a lab simulated environment, and the results can vary in certain field applications due to a number of factors. OSRAM does not take over any responsibility, warranty or liability that these results can also be achieved by using the devices under other conditions, or when using successor models of the tested devices, or different models of the same manufacturer. In case of non-observance of the instructions, safety risks like overheating of SubstiTUBE or ECG may occur in rare cases. Due to the characteristic light distribution of the SubstiTUBE Advanced UO UN, the resulting luminaire light characteristic is likely to change. It is not guaranteed that e.g. standards for lighting at working places will be complied to after replacement. A photometric check of the installation is recommended. The effective energy savings depend on the efficiency of the luminaire setup to be replaced and should be considered individually in each case. Particularly magnetic ballast losses are reduced to ohmic losses and are normally only about 1 W. The SubstiTUBE Advanced UO UN is protected according to IP20. Applications with external risk of moisture and dust can be served with an adequately protected luminaire. SubstiTUBE products differ in their diameters and geometries from fluorescent lamps. Their use in open batten luminaires with gaskets is possible if no excessive force is expended during the fixing. Obtaining the necessary IP protection in open batten luminaires with gaskets cannot be ensured. ST8AU-1.2m-UN August 2016 Page 3 of 6

4 SubstiTUBE Advanced UO UN may also be driven directly on line voltage. In order to grant a safe operation mode please refer to the installation instructions for further information. Photobiological Safety of lamps and lamp systems according to IEC Risk Group: Exempt Installation Instructions for CGG Make sure that the supply voltage is disconnected. Carefully remove the fluorescent tube and starter according to the lamp holder type. Insert SubstiTUBE Advanced UO UN and SubstiTUBE Start properly. Remark: Please use the starter which is enclosed in the packaging! Below an example for typical lamp holder types is described Turn the conventional lamp 90 degrees and take it out of the socket. Remove the conventional starter by turning it. Insert and latch the SubstiTUBE Start into starter socket. Insert SubstiTUBE Advanced UO UN into socket and locate into position by turning 90. Press safety buttons on each side of the lamp and connect SubstiTUBE to supply voltage Check light emission direction. ST8AU-1.2m-UN August 2016 Page 4 of 6

5 Circuit diagram of a retrofitted CCG luminaire ST8AU-1.2m-UN August 2016 Page 4 of 6

6 Installation Instructions for ECG Below an example for typical lamp holder types is described Make sure that the supply voltage is disconnected (1). Turn the conventional lamp 90 (2) and take it out of the socket carefully (3). Insert SubstiTUBE Advanced UO UN into socket (4) and locate into position by turning 90 (5). Activate tube by pushing the two safety buttons (6), (7). Connect SubstiTUBE Advanced UO UN to supply voltage (8). Check light emission direction ST8AU-1.2m-UN August 2016 Page 5 of 6

7 Compatibility list Luminous flux will change in dependency of used ballast. SubstiTUBE Advanced Universal 1.2 m OSRAM QT FIT8 1x36 1x OSRAM QTP8 2x36 2x OSRAM QT FIT8 2x36 2x OSRAM QT Fit 5/8 1x x OSRAM QTP-OPTIMAL 1x x OSRAM QTP8 1x36 1x OSRAM QTP-OPTIMAL 2x x OSRAM QT Fit 5/8 2x x BAG BCS36.1FX-11 1x BAG BCS36.2FX-11 2x Helvar EL2x36/40s 2x Helvar EL1x36/40/18s 1x Helvar EL2x36ngn 2x Helvar EL2x36HF 2x Philips HF-B 136 TL-D EII V 1x Philips HF-S 336 TL-D II V 3x Philips HF-S 236 TL-D II V 2x Philips HF-S 136 TL-D II V 1x Philips HF-P 336 TL-D III V 3x Philips HF-P 236 TL-D EII V 2x Philips HF-B 236 TL-D V 2x Philips HF-P 136 TL-D III V 1x Philips HF-P 236 TL-D III V 2x Philips HF-P 136 TL-D III V 1x Philips HF-P 336 TL-D EII V 3x Tridonic PC 2x36 T8 TOP sl 2x Tridonic PC 2x36 T8 PRO sl 2x Tridonic PC 1x36 T8 TOP sl 1x Tridonic PC 1/30 T8 PRO 1x Tridonic PC 1x36 T8 PRO lp 1x Tridonic PC 1/36 T8 PRO sc 1x Trilux D E 136W 1x Vossloh ELXc x Vossloh ELXc x Vossloh ELXc x ST8AU-1.2m-UN August 2016 Page 4 of 6

8 Ordering guide Product name Light color EAN* S-Unit** ST8AU-1.2m-16W-865-UN Cool Daylight / 6500 K ST8AU-1.2m-16W-840-UN Cool White / 4000 K x 1 * EAN: Ordering number per single module ** S-Unit: Lamps per shipping unit Sales and Technical Support Sales and technical support is given by the local OSRAM subsidiaries. On our worldwide homepage all OSRAM subsidiaries are listed with complete address and phone numbers. Further Information Downloads: Eulumdat /IES files, CE declaration In process OSRAM GmbH Head Office: Marcel-Breuer-Strasse Munich, Germany Phone ST8AU-1.2m-UN August 2016 Page 6 of 6