TECHNICAL BULLETIN INTRODUCTION. Bad Boy Luminaire Baseplate Retrofit. Parts, Tools, and Supplies

Transcription

1 TECHICAL BULLETI Product: Bad Boy Spot Luminaire Manufacturer: PRG Subject: Baseplate Retrofit Bulletin o: BAD-014 Date: ITRODUCTIO Bad Boy Luminaire Baseplate Retrofit It has been determined that some Bad Boy baseplates have the possibility for weakness at the two slots where the safety cables are attached. In extreme cases the outer edge of the slot can break off, leaving nowhere to attach the safety cable. In order to prevent this problem, all Bad Boy baseplates should be replaced. This technical bulletin provides a procedure for replacing the baseplate. This procedure applies to the following locations: + Australia, Germany, Japan, UK When complete, the TEAM inspection should be completed by UK locations. For all other locations, the fixture serial numbers to badboyservice@prg.com PRG Dallas will perform this retrofit for all orth American locations. Please coordinate this with your Asset Management. Baseplate Parts, Tools, and Supplies KIT, BASEPLATE RETROFIT EA LABEL, COMPLIACE, BAD BOY EA ASSY, BASEPLATE RETROFIT EA SCREW, 3/8-16 x 1-1/4 FLAT EA UT, 3/8-16 YLO ISERT KIT, BAD BOY BASEPLATE RETROFIT TOOL LOCTITE, 242 THREADLOCKER ADHESIVE, 1.69 oz. BLUE SCREWDRIVER, PHILIPS ROUD BLADE, #2 TIP, 1" BLADE, ULTRA-GRIP SCREWDRIVER, PHILIPS ROUD BLADE, #2 TIP, 8" BLADE, ULTRA-GRIP WRECH, 3/8" SQUARE DRIVE W/ SOCKET RELEASE, 5-75 FT-LBS ADJUSTABLE CLICK- STYLE SOCKET, 3/8" SQUARE DRIVE 6-POIT STD, 9/16" SIZE, 1-1/8" LEGTH PLIERS, 8-1/4" LOG-OSE EXTRA REACH, " JAW LEGTH, 5/32" TIP PLIERS, WIRE-CUTTIG W/SPRIG RETUR, OVAL, 6-3/8" LEGTH, 7/8" JAW HEX KEY, 7/32" MOLDED SMOOTH-GRIP T-HADLE, 4" BLADE WRECH, 9/16" SIZE 8-5/8" LEGTH, RATCHETIG COMBO BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 1 OF 8

2 PROCEDURES Replacing the Baseplate WARIG: Remove power from luminaire before performing any maintenance procedures. To replace the baseplate: Step 1. Remove power from luminaire and allow components to cool for at least 5 minutes. Step 2. Remove Enclosure Covers as follows: a. At each Enclosure Cover, loosen two captive screws (Figure 1). b. Remove cover by pulling straight out until lip clears yoke support. CAUTIO: The Enclosure Covers are not identical. One is for the Intake side and one for the Exhaust side. Be sure to re-install covers in the proper location. Exhaust Cover PRG Sticker Intake Cover Mesh Screen Captive Screw (2) Figure 1: Removing Upper Enclosure Covers BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 2 OF 8

3 Step Step 3. Remove EMI Ballast Enclosure as follows: a. Disconnect the following wiring (Figure 2): 1) APS Cable. 2) Two Fan Cables. 3) Ground Cable. 4) Lamp Power Ballast Output Cables (white and black). b. At EMI Ballast Enclosure, remove four x 3/8" PPB Black SEMS screws. (Assembly will still be connected by wiring.) c. Move EMI Ballast Enclosure away from the luminaire as far as the cabling will allow. (This will provide access to disconnect the remaining cables.) d. At EMI Filter, disconnect two output cables. e. Cut tie-wrap to free Lamp Power Ballast Output Cables. f. Remove EMI Ballast. 4. Remove Interface/LVS Module as follows: a. At Interface/LVS Module, remove four x 3/8" PPB SEMS screws (Figure 3). b. At left side of Interface/LVS Module, disconnect the following wiring: 1) Fan cable. 2) APS Control Line cable. 3) eutral (white) cable. 4) Line (black) cable. 5) Ground cable. c. At right side of Interface/LVS Module, disconnect the following wiring: 1) Fan cable. 2) CA Bus cable. 3) Power cables (red and black). d. Remove Interface/LVS Module. BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 3 OF 8

4 1 BALLAST POLARITY 2 TO CABLE ASSY BALLAST COTROL FROM CHASSIS GD STUD AC EUT WHT FROM EMI FILTER PCB AC LIE BLK L CABLE LAYOUT - REAR VIEW x 3/8" PPB Black SEMS Screw (4) TO LEFT EXTESIO FA 1 BALLAST COTROL EMI Ballast Enclosure TO RIGHT EXTESIO FA 2 BALLAST COTROL BLACK WHITE 1 2 FROT VIEW SIDE VIEW Fan LAMP WIRES APS Fan EMI Ground EMI Output Cables EMI Filter EMI Filter Ground - Loctite #242 ote: Be careful to maintain correct polarity of the lamp wires during re-assembly. Figure 2: Removing EMI Ballast Enclosure BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 4 OF 8

5 C3 Power Cables: FA Low Voltage DC Output BLACK AC Line Input WHITE BLACK C1 L Do not disconnect cables from positions 4 & 5 RED 2 GR/YEL 1 LVS DETAIL Enclosure CA Bus Fan x 3/8" PPB SEMS Screw (4) Fan L GD Interface/LVS Module WHT BLK WHT BLK GD POWERCO GD LVS GD Figure 3: Removing Interface/LVS Module BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 5 OF 8

6 Serial umber Step 5. Remove and save Compliance Label (with serial number and barcode) as shown in Figure 4. This Fixture requires a supplemental Safety Serial umber Figure 4: Removing Compliance Label from Baseplate Step 6. Remove Baseplate from luminaire as follows: a. At bottom of Baseplate, remove four 8-32 x 3/4" PF screws which secure Coverstrap (Figure 5). b. Remove four 3/8-16 x 1-1/4" socket screws and nuts securing Baseplate to Pan Tube. Discard hardware. c. Remove Baseplate. ote: Luminaire Head not shown for clarity. Coverstrap Pan Tube 3/8-16 ylon Insert ut (4) - DISCARD Baseplate 8-32 x 3/4" PF Screw (4) 3/8-16 x 1-1/4" Flat Socket Screw (4) - DISCARD Figure 5: Removing Baseplate BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 6 OF 8

7 Step 7. Remove remaining Baseplate components as follows: a. Remove entire Battery Assembly by removing two 6-32 x 1/4" PPZ screws. b. Remove EMI Filter by removing two 6-32 x 1/4" PPZ screws. c. Discard Baseplate x 1/4" PPZ Screw (2) 6-32 x 1/4" PPZ Screw (2) EMI Filter Battery Assembly Baseplate Figure 6: Disassembling Baseplate Step 8. Install Battery Assembly and EMI Filter on new Retrofit Baseplate ( ). (Refer to Figure 6) Step 9. Reattach Baseplate to Pan Tube using EW hardware included in kit. (Refer to Figure 5.) Torque 3/8-16 hardware to 30 ft-lbs. Step 10. Secure Coverstrap to Baseplate. (Refer to Figure 5.) Apply Loctite 242 to 8-32 x 3/4" screws. Step 11. Reinstall Interface/LVS Module. (Refer to Figure 3.) Step 12. Reinstall EMI Ballast. (Refer to Figure 2.) BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 7 OF 8

8 L I S T R TM 8617AMBASSADOR ROW Bad Boy Luminaire DALLAS, TX 75247U.S.A IP20 OT FOR RESIDETIAL USE VAC IMPROPERE A L'USAGE DOMESTIQUE 50 / 60 Hz SUITABLE FOR DRY LOCATIOS OLY 15A Max. EMPLACEMET SECS FOR USE BY QUALIFIED PERSOEL OLY 6061-T6 T A =50C 0 THIS DEV ICE COMPLIES WITH PART15 OF THE FCC RULES. OPE RATIO IS SUBJECT TO THE FOLLOWIG TWO CODITIOS: (1) THIS DEV ICE MAY OT CAUSE HAR MFUL ITERFE RECE, AD (2)THIS DEV ICE MUSTACCEP TAY ITERFERECE RECEIVE D, ICLUDIG ITERFERECE THAT MAY CAU SE UDES IRED OPE RATIO. WARIG: RISK OF FIRE AD ELECTRIC SHOCK. 0 T MI. DISTACE FROM HEAD TO MAX =140 C 1.50M FLAMMABLE OBJECTS: 0.5M COFORMS TO R UL STD 1573 C L I S T E D US CERTIFIED TO CA/CSA STD E598-1 CA/CSA STD E Serial umber Step 13. Apply new Compliance Label ( ) to Baseplate. Ensure label is oriented as shown in Figure 7. Step 14. Transfer serial number and TEAM barcode labels from old Compliance Label to new Compliance Label. ote: It is not necessary to reapply the Supplemental Safety Label. Install in orientation shown here 2200Watts IPUT RATIG: WARIG: RISK OF POSSIBLE LAMP EXPLOSIO. SERVICE AD MAITEACE SHOULD BE PERFORMED OLY BY QUALIFIED PERSOEL AS DETERMIED BY PRG LIGHTIG. PROTECTIVE CLOTHIG AD PROCEDURES AS OUTLIED I THE PRG USER MAUAL MUST BE FOLLOWED. CAUTIO: SERIOUS IJURY MAY RESULT A PROPER MEAS OF VETIG MUST BE PROVIDED. FROM THE GEERATIO OF OZOE BY THIS LAMP SYSTEM. Compliance Label (new) 8617 AMBASSADOR ROW DALLAS, TX U.S.A. TM Bad Boy Luminaire IPUT RATIG: 2200 Watts IP20 OT FOR RESIDETIAL USE VAC IMPROPERE A L'USAGE DOMESTIQUE 50 / 60 Hz SUITABLE FOR DRY LOCATIOS OLY 15A Max. EMPLACEMET SECS FOR USE BY QUALIFIED PERSOEL OLY THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIO IS SUBJECT TO THE FOLLOWIG TWO CODITIOS: (1) THIS DEVICE MAY OT CAUSE HARMFUL 6061-T6 ITERFERECE, AD (2) THIS DEVICE MUST ACCEPT AY ITERFERECE RECEIVED, ICLUDIG ITERFERECE THAT MAY CAUSE UDESIRED OPERATIO. WARIG: RISK OF POSSIBLE LAMP EXPLOSIO. SERVICE AD MAITEACE SHOULD BE PERFORMED OLY BY QUALIFIED PERSOEL AS DETERMIED BY PRG LIGHTIG. PROTECTIVE CLOTHIG AD PROCEDURES AS OUTLIED I THE PRG USER MAUAL MUST BE FOLLOWED. CAUTIO: SERIOUS IJURY MAY RESULT FROM THE GEERATIO OF OZOE BY THIS LAMP SYSTEM. A PROPER MEAS OF VETIG MUST BE PROVIDED. WARIG: RISK OF FIRE AD ELECTRIC SHOCK. T A = C T MI. DISTACE FROM HEAD TO MAX =140 C 1.50M FLAMMABLE OBJECTS: 0.5M C E D US COFORMS TO UL STD 1573 CERTIFIED TO CA/CSA STD E598-1 CA/CSA STD E Serial umber TEAM Barcode (from old label) Serial umber (from old label) Figure 7: Applying ew Compliance Label to Retrofit Baseplate Step 15. Power up and test as follows: a. Apply power to luminaire and allow it to calibrate. b. Verify no errors are present. c. Strike lamp and allow it to warm up to full power. d. Douse lamp. Step 16. Complete TEAM inspection (UK only). For all other locations, fixture serial numbers to badboyservice@prg.com BULLETI O: BAD-014 BAD BOY BASEPLATE RETROFIT PAGE 8 OF 8