Optical Broadband Platform NEW: Passive optical components

Transcription

1 Optical Broadband Platform NEW: Passive optical components Antennen Electronic

2 Optical Broadband Platform Optical broadband platform for up to 16 modules Equipped with 2 redundant power supply and fan units Wide selection of optical transmitters, amplifiers and return path receivers All optical and electrical connections are located on the rear panel. Test sockets are on the front panel Can be integrated in every HMS-conform monitoring system Pluggable control panel with LC display, LEDs and input keys Tuning and management also via web browser RS 485 remote monitoring and control interface Several optical broadband platforms can be managed using just one controller module Automatic redundant operation of adjacent modules High reliability due to dust-proof designed modules and large cooling ribs Models available for mains voltage ( V AC ) and direct voltage ( V DC ) Design: 19 racking, 4 height units (HU) Kathrein's KOBRA system offers a comprehensive broadband platform meeting all the requirements of optical transmission. A wide range of optical transmitters, amplifiers and return path receivers is complemented by individual units in 19 design. The foundation is based on the 19 broadband platform KBP 4000R, into which a total of 16 modules can be inserted. It is already equipped with two redundant power supply and fan units ensuring reliable operation. The product package additionally includes a pluggable control panel with LC display, status LEDs and input keys. A power bus system in the rear section of the platform enables direct module connection to the 24 V DC supply voltage, to the RS 485 remote supervision and control interface as well as to control panel management. The broadband platform is designed as a 4 HU module carrier and can also be adapted to ETSI cabinets. For use in hubs, for example, the remotely fed broadband platform 48 V DC variant (KBP 4048R) can also be used. Extensive management and monitoring facilities allow flexible and reliable operation in any net configuration. The provided pluggable control panel enables all required settings to be made on inserted devices. The net element controller module Ethernet (NCM 10) plays the leading role in this function. This unit establishes the connection between the control panel and all plugged-in modules via the RS 485 bus. The NCM 10 can thereby control up to three full KBP 4000R or 4048R broadband platforms. On the other hand, it converts the RS 485 data to SNMP/Ethernet and web browser/ Ethernet protocol. Thus, all settings and queries can be carried out via PC with a web browser. In addition, it is possible to integrate the broadband platform in any HMS-compatible monitoring system such as the KOM system from Kathrein. Together with the Kathrein optical compact receivers, the KOBRA can be used to set up an optical distribution system that meets each and every requirement. Modular design and a broad product programme make it possible to design anything in a costeffective fashion from simple optical feeds to classical HFC structures and video distribution in FTTH networks. Kathrein are continually enhancing their products and expanding their product range. Additional product variants are available upon request. 2 3

3 Functional and reliable - the optical broadband platform in detail The optical broadband platform KOBRA is designed with a sophisticated operation and management concept. The central element is the net element controller Ethernet "NCM 10. This module provides the interface to the rear RS 485 bus to which all platform modules are connected. In addition, it establishes the connection to external management systems, e.g. via web browser, or monitoring systems, such as HMS monitoring systems. Power supply Ethernet NCM VDC µp LC Display I/0 RS485 Input Keys 2 Power supply 3 Gerät 16 Two redundant power supply units, each equipped with double fan units, ensure high reliability. If service is required, the power supply units can even be exchanged under operational conditions (hot-pluggable). Ultimately, it enables local setting of all parameters through the control panel with display and input keys. Decentralized data storage in each individual module allows independent operation (without the controller module) after start-up. Ample cooling ribs guarantee long endurance of all active components. An additional advantage is the dust-proof design of all components. Slim modules, some with dual functions (e.g. return path receiver), ensure high functional density. Minimal space requirement increases cost-effectiveness and makes later upgrading easier. Despite their high output power, the optical amplifiers only require two or three slots. All test sockets are located on the front panel. This guarantees easy access for tests or measurements. The cooling air only flows along the cooling ribs and not through the modules themselves. Disturbances due to dust and dirt are therefore practically ruled out. The optical and RF interfaces are located on the rear panel of the platform, simplifying cabling in 19 racks. 4 5

4 19" Broadband platform for optical modules Net element controller module Ethernet KBP 4000R KBP 4048R Up to 16 modules can be inserted into the broadband platform Fitted with 2 redundant power supply and cooling fan units Power supplies can be exchanged under operation Plug-in controller with LC display, status LEDs and input keys Bus for: - 24 V DC module power supply - RS 485 remote monitoring and control interface - Controller management Models available for V AC and 48/60 V DC powering Automatic recognition of inserted modules Design: 19 racking, 4 height units (HU) Can be adapted to ETSI defined cabinets Note: The net element controller module Ethernet NCM 10 is required if modules are to be tuned to other settings and for monitoring purposes NCM Zum For management Management and und monitoring Überwachung of active aktiver modules in the in 19 der broadband 19 -Breitband- platform Plattform KBP 40xxKBP 40xx Umwandlung Conversion of von RS RS Daten data in to SNMP/Ethernet- and und Webbrowser/ Ethernet-Protokoll protocol Schnittstelle Interface to displays zu Displays and und input keys on Eingabetasten the front panel der Fronteinheit Automatische Automatic recognition Erkennung of aller modules an den RS connected 485-Bus to angeschlossenen the RS 485 bus Schnittstelle Ethernet interface Ethernet 10/100 10/100 Mbit/s Mbit/s for für SNMPv1 und and Webserver Flash Microcontroller-Technologie micro-controller technology for für schnelle rapid and und simple leichte software Software-Updates updates via über Ethernet die Ethernet-Schnittstelle interface LEDs zur for status Statusanzeige display Niedrige Low power Leistungsaufnahme consumption Hinweis: Note: Ein Up to NCM three 10 broadband kann bis zu platforms drei Breitband- Plattformen KBP 40xxR KBP can be 40xxR managed verwalten and und überwachen monitored by one NCM 10 module Type KBP 4000R KBP 4048R Order no Input voltage V AC: DC: Power consumption max. W < 240 < 240 Power consumption of inserted modules max. W < 192 < 192 Dimensions (W x H x D) mm 483 x 102 x x 102 x 476 LAN / WAN TCP/IP RJ45-Cable Ethernet NCM 10 Kobra Broadband Platform #1 Kobra Broadband Platform #2 Kobra Broadband Platform #3 µp LC Display RS 485 RS 485 I/O RS Input Keys RJ45 Cable RJ45 Cable Weight kg Type NCM 10 Order no Power consumption W

5 Directly modulated broadcast transmitters, 1310 nm, extremely linear 1303X2-E X2-E X2-E X2-E X2-E X2-E Opto-electrical conversion of the forward path signal Extremely linear, low-noise laser with pre-distortion technology Optical output power between 3 and 14 dbm Adjustable optical output level, 0 to -3 db (relative) Active narrowcast input (NC) with high decoupling to the broadcast signal (BC) Electronic tuning elements for attenuation, slope, output level, Optical Modulation Index (OMI) etc. Automatic load control for constant OMI RS 485 interface Optical interface: E-2000, 0.1 db-type (other connector types on request) Test socket for input signal Test socket for RF signal in front of the laser diode Type 1303X2-E 1305X2-E 1308X2-E 1311X2-E 1313X2-E 1314X2-E Order no Nominal output level optical dbm Wave length nm 1310 Optical output level range (relative) db 0 to -3 Optical return loss db > 45 RF frequency range MHz Nominal input level (5 % OMI, Broadcast) Nominal input level (5 % OMI, Narrowcast) Level range (BC), in relation to nominal input level, electronically settable Slope range (BC), electronically settable Level range (NC), electronically settable dbµv 80 dbµv 80 dbµv db dbµv Decoupling between BC and NC input db > 50 Return loss at 47 MHz db /oct., > 15 Return loss 5-65 MHz db > 18 Impedance Ω 75 Power consumption (operation) W 12 Power consumption (stand-by) W 4 CSO (CENELEC 42) dbc 68 CTB (CENELEC 42) dbc 69 NEW: Active narrowcast input 8 9

6 Optical return path receivers, twin Optical return path receiver, quad ORM 22E ORM 40E Opto-electrical conversion of return path signals Two receivers, with individual shut-down Two separate outputs with test sockets Redundant operation possible Optical power monitoring on all inputs Pilot-controlled Wide optical input power range RS 485 Interface Stand-by mode for unused receiver to reduce power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type (other connectors on request) TP #1 ICS #1 IN #1 OUT #1 µp RS485 Opto-electrical conversion of return path signals Four receivers, with individual shut-down Four separate outputs, each switchable to the test port Redundant operation possible Optical power monitoring on all inputs Pilot-controlled and optical power controlled AGC as well Wide optical input power range RS 485 Interface for supervision and control Line code evaluation Stand-by mode for unused receiver to reduce the power consumption Very low power consumption Optical interfaces: E-2000, 0.1 db-type (other connectors on request) Requires two slots in KOBRA KBP 40xx-R subrack LEDs LON µp µc PSK AGC Demod (opt. input power RS485 or pilot contr olled ) Optical input dBm Optical input dBm dB dB dB dB 20 db test point RF output >85dBµV 20 db test point RF output >85dBµV Optical input RF output dBm dB dB >85dBµV ICS #2 IN #2 OUT #2 Optical input 20 db test point RF output OR265-nn TP # dBm dB dB 20 db test point >85dBµV Type ORM 22E Type ORM 40E 10 Order no Optical interfaces E-2000 Optical wave length nm Optical input level range dbm -16 to +2 Optical return loss db > 40 RF frequency range MHz RF output level at OMI = 5 % dbµv 90 Frequency response db ± 0.75 Return loss db > 19 Pilot control range db 36 Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption, normal operation/stand-by W 3.5/1.5 Order no Optical interface E-2000 Optical wave length nm Detector responsivity A/W 0.8 Receiver noise current at -16 dbm pa/ Hz 2.5 Optical input level range dbm -16 to +2 Optical return loss db > 45 RF frequency range MHz RF output level at OMI = 5 % dbµv 75 Frequency response db ± 0.75 Return loss at 47 MHz db > 20 RF output connector F-type Test port connector F-type Pilot control range db 26 Frequency of ALC pilot tone khz Optical modulation index pilot % 5 Test sockets db 20 Impedance Ω 75 Power consumption normal operation (all 4 receivers active)/stand-by W 8/1.5 CINR at -11 dbm (4 QAM carrier with 2 MHz bandwidth, 10 % OMI) db 50 11

7 Optical amplifiers Broadband amplifier, MHz 113S-E S-E S-E S-E S-E S-E Amplifies optical signals in the 1550 nm range Optical output power 13 or 16.5 dbm respectively; 1-4 outputs, type dependant Monitoring of optical input and output levels and pump laser current 1 or 2 pump lasers, type dependant Automatic switch-off in case of low input level Low noise figure Stand-by mode for low power consumption Requires two or three slots in the optical broadband platform KBP 40xxR Optical interfaces: E-2000, 0.1 db-type (other connectors on request) TVO Broadband amplifier for universal use in forward and return paths For use in the optical broadband platform KOBRA Automatic load control (can be switched off) Frequency range MHz Gain db, electronically settable Slope range db, electronically settable Main input for broadcast signals and secondary input for narrowcast signals Test socket for output signal Stand-by mode for low power consumption RS 485 interface IN IN (coupled) CA1024 ATT, EQ µp OUT TP RS485 Type TVO 1024 Order no Frequency range MHz Type 113S-E 213S-E 413S-E 116S-E 216S-E 416S-E Order no Optical wave length nm Optical interfaces E-2000 Optical return loss db 50 Optical input level dbm Noise figure (at 0 dbm) db < 4.8 Optical output level per output dbm Optical output power tolerance ( / nm) db ± 0.5/0.8 No. of outputs No. of pump lasers Power consumption, operation W Power consumption, stand-by W No. of required slots in KBP 40xxR Gain, electronically settable db 0 to 24 Slope electronically settable db 0 to 16 Frequency response (7-870 MHz) db ± 0.8 Frequency response ( MHz) db ± 1.5 Input level narrowcast input 1), relative to main input db + 14 Max. output level 2), CSO > 60 db, CTB > 60 db dbµv 106 Return loss 5-65 MHz db > 18 Return loss MHz db 18-1/oct., > 15 Noise figure MHz db 6.5 Noise figure MHz db 7.5 Impedance Ω 75 Power consumption, normal operation W 9 Power consumption, stand-by mode W 1 1) 14 db directional coupler 2) CENELEC channel plan, 42 channels, flat 12 13

8 Externally modulated transmitters (19" design), 1550 nm Optical amplifiers (19" design) ESA 1085XA-E ESA 1085XA-E Opto-electrical conversion of forward path signals Designed for operation with optical amplifiers (EDFAs/YEDFA) Excellent parameters enable design of optical distribution systems over 100 km in length Very low-noise, narrow-band DFB laser Optical modulator with 2 optical outputs Automatic RF gain control: CW carrier, video or manual Settable SBS threshold up to 19 dbm Service interface: HTTP/SNMP Ethernet LC display and LEDs on front panel: Optical wavelength nm (ITU channel 23) Additional wavelengths and optical output levels on request Optical interfaces E-2000, 0.1 db-type (other connectors on request) Test socket -20 db Two power supply modules, pluggable/exchangeable during operation Design: 19 racking, 1 height unit, depth 600 mm Power supply 230 V AC or 48 V DC /60 DC, type dependant OBV OBV OBV OBV Amplifies optical signals in the 1550 nm range Optical output power 16.5 or 20 dbm, 8-32 outputs, type dependant Monitors optical input and output levels as well as pump laser current ErYb-doped optical amplifier Low noise figure LC display, LEDs and input keys on front panel RS 485 interface for management Ideal for FttH or HFC applications Optical interfaces: LC/APC Design: 19 racking, 1 height unit (HU) Two power supply modules, pluggable/exchangeable during operation 14 Type ESA 1085XA-E ESA 1085XA-E Order no Optical interfaces E-2000 Optical wave length nm Optical output level dbm 2 x 8.5 Relative intensity noise (RIN) dbc/hz -160 Input level, per TV channel, nominal dbµv 80 AGC dynamic range db Return loss at 47 MHz db / oct., > 15 Frequency range MHz Frequency response, MHz db ± 0.75 Test socket db -20 ± 1 RF interfaces F-type connector (female) Voltage supply V AC ± ± 72 DC Power consumption W 60 Type OBV 1616 OBV 3216 OBV 820 OBV 1620 Order no Optical wave length nm Optical return loss db 45 Optical input level dbm Noise figure (at 0 dbm) db < 5.5 Optical output power per output dbm Optical decoupling, input db 35 Optical decoupling, output db 35 No. of outputs W Power consumption, max. W Supply voltage V AC

9 FTTx CATV splitter 19", 1 HU FTTx CATV splitter WDM 19", 1 HU BOS 264LC BOS 432LC racking (1 HU) Suitable for up to 2 x 64 fibres Includes two independent optical 1:64 splitters or four independent 1:32 splitters Combined input and outputs with LC/APC connectors ITU G compliant Broadband PLC splitter Integrated fibre tray BOW 064LC BOW 232LC racking (1 HU) to feed in CATV signals with 1550 nm in GBE-FTTx and PON-FTTx networks Suitable for up to 64 fibres Single-fibre solution for Triple Play systems with CATV overlay Data inputs with LC or LC/APC connectors CATV input and combined outputs with LC/APC connectors ITU G compliant Type BOS 264LC BOS 432LC Order no Configuration 2 x 1:64 4 x 1:32 Wave length range nm Max. insertion loss per splitter ¹) db Uniformity db < 1.0 < 1.0 Polarisation dependent loss db Typ. isolation (directivity) db Min. return loss db Temperature range (operational) C Temperature range (storage) C Relative humidity (non-condensing) % Max. optical output mw < 300 < 300 Dimensions (W x H x D) mm 482 x 45 x x 45 x 196 Fibre type (Core diameter/sheathing diameter/ outer diameter) µm 9/125/250 9/125/250 Type of optical connection LC/APC LC/APC Type BOW 064LC BOW 232LC Order no Configuration 1 x 1:64 with WDM 2 x 1:32 with WDM Wave length data downstream nm Wave length data upstream nm Wave length CATV downstream nm Typ. insertion loss data ¹) db Max. insertion loss CATV ¹) db Typ. isolation data upstream to CATV db Min. return loss db Temperature range (operational) C Temperature range (storage) C Relative humidity (non-condensing) % Max. optical output mw < 300 < 300 Dimensions (W x H x D) mm 482 x 45 x x 45 x 196 Fibre type (Core diameter/sheathing diameter/ ¹) Einschließlich opt. Steckverbindungen outer diameter) µm 9/125/250 9/125/250 ¹) Including opt. connectors ¹) Including opt. connectors 16 17

10 Optical splitters Optical taps BOV BOV BOV BOV BOV 002-CWDM BOV 003-CWDM BOV 004-CWDM Optical splitters for universal application Low insertion loss Optimised for 1310 and 1550 nm wave lengths Optical connectors: E-2000 (other connector types available on request) High reliability Ultra-compact design, including pigtails BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC Optical splitters for universal application Low insertion loss Optimised for 1310 and 1550 nm wave lengths Optical connectors: E-2000 (other connector types available on request) Ultra-compact design, including pigtails Type BOV 002 BOV 003 BOV 004 BOV 008 BOV 002- CWDM BOV 003- CWDM BOV 004- CWDM Order no Optical wave length nm 1310 and Splitting ratio 1:2 1:2 1:2 1:8 1:2 1:2 1:2 Typ. insertion loss ¹) db Max. insertion loss ¹) db Uniformity db Optical isolation, outputs db 50 ¹ ) Without connector Type BOC 003 BOC 004 BOC 005 BOC 006 BOC 007 BOC 008 BOC 009 BOC 010 BOC 012 BOC 014 Order no Optical wave length nm 1310 und 1550 Typ. tap loss ¹ ) db Tap loss tolerance db +/ / / / / / / / / /- 1.5 Typ. through loss ¹ ) db Through loss tolerance Optical isolation, outputs db +/ /- 0.3 db

11 Optical patch cables/optical couplers OFC 050/E yellow OFC 150/E yellow OFC 300/E yellow OFC 050/E red OFC 150/E red OFC 300/E red OFC 300/SC OFC 300/LC OFC 300/LC-E Optical patch cables for universal application 2.5 mm patch cord Type OFC 050/E yellow OFC 150/E yellow OFC 300/E yellow OFC 050/E red OFC 150/E red OFC 300/E red OFC 300/ SC OFC 300/ LC OFC 300/ LC-E Order no Length cm Diameter of patch cord mm Opt. attenuation of connectors db OKU 01/SC OKU 01/SC-E OKU 01/E Optical couplers for universal application Available types: - OKU 01/SC: SC/APC both ends - OKU 01/SC-E: Optical connection adapter SC/APC to E OKU 01/E: E-2000 both ends The products described must only be installed by qualified specialists. Please consult the provided instruction manuals for safety instructions that are to be considered during use /1/0509/JH/Pf Subject to modification. Technical data represent typical values. Internet: catv@kathrein.de KATHREIN-Werke KG Phone +49 (0) Fax +49 (0) Anton-Kathrein-Str. 1-3 P. O. Box Rosenheim GERMANY Antennen Electronic