BATTERY-OPERATED WIRELESS PROJECTOR WITH RGB LEDS USER GUIDE July 2012 Version 1.0

Transcription

1 BATTERY-OPERATED WIRELESS PROJECTOR WITH RGB LEDS USER GUIDE July 2012 Version 1.0

2 English 1 - Safety information Important safety information airled-9x3tcb - Battery-operated wireless projector with RGB LEDs WARNING : This unit contains no user-serviceable parts. Do not open the housing or attempt any maintenance by yourself. In the unlikely even your unit may require service, please contact your nearest dealer. This unit is intended for indoor use only. Do not use it in a wet, or extremely cold/hot locations. Failure to follow these safety instructions could result in fire, electric shock, injury, or damage to this product or other property. Any maintenance procedure must be performed by a CONTEST authorised technical service. Basic cleaning operations must thoroughly follow our safety instructions. In order to avoid any electrical malfunction, please do not use any multi-socket, power cord extension or connecting system without making sure they are perfectly isolated and present no defect. This product contains non-isolated electrical components. Do not undertake any maintenance operation when it is switched on as it may result in electric shock. Symbols used This symbol signals an important safety precaution. The WARNING symbol signals a risk to the user s physical integrity. The product may also be damaged. The CAUTION symbol signals a risk of product deterioration. Recommendations concerning batteries 1 - Handling the battery: Never short-circuit the battery. A short-circuit creates a very high current which causes overheating and may lead to electrolyte leaks, gas emission or explosion. Do not drop or shock the battery as it my result in a degradation of its electrical properties. Keep the battery away from important heat sources as there is a risk of explosion. 2 - Modifying the battery: Do not weld cables directly on the battery as insulating components might be damaged by the heat. The battery is made up of 21 Lithium cells, do not try to separate them as it may result in a short-circuit. 3 - Chemical risks: Lithium batteries are usually not subject to leaks, but in the event of a skin contact with liquid leaking from the battery, please flush with water and seek medical advice immediately. 4 - Contact with fire: Do NOT incinerate or burn the battery as it may result in an explosion. 5 - Contact with liquids: Do NOT put the battery in contact with water, drinks, etc. Warning This product is equipped with Class 2 LEDs. Please avoid looking directly at the beam as it may cause severe eye injuries. Recycling your device As HITMUSIC is really involved in the environmental cause, we only commercialise clean, ROHS compliant products. When this product reaches its end of life, take it to a collection point designated by local authorities. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. 6 - Damaged battery: Do not use a shocked, disformed or leaking battery. If you suspect any suspicious smell, keep the battery away from any heat source to avoid risks of explosions or fire. 7 - Storage and periods of non-use: The battery must be stored at room temperature, being charged at 30 or 50%. During long periods of non-use it is recommended to charge the battery every 6 months to avoid excessive discharges. 8 - Lifespan: The battery works with chemical reactions, as a result its performances decreases even if it is not used for long periods. Moreover, the multiples charge-discharge cycles, temperature fluctuations etc. lead to battery deteriorations and can damage the device, e.g. in case of electrolyte leaks. If the battery does not hold charge properly, it means it has reached the end of its life and must be replaced. 9 - Recycling: Spent batteries must be taken care of by specific entities. Do not throw. Do not dispose of it in the environment Guarantee: This battery is considered as wearing part and is not covered by the guarantee. 2

3 airled-9x3tcb - Battery-operated wireless projector with RGB LEDs English Instructions and recommendations 10 - Electric power supply : 1 - Please read carefully : We strongly recommend to read carefully and understand the safety instructions before attempting to operate this unit. 2 - Please keep this manual : We strongly recommend to keep this manual with the unit for future reference. 3 - Operate carefully this product : We strongly recommend to take into consideration every safety instruction. 4 - Follow the instructions: Please carefully follow each safety instruction to avoid any physical harm or property damage. 5 - Avoid water and wet locations : Do not use this product in rain, or near washbasins or other wet locations. 6 - Installation : We strongly encourage you to only use a fixation system or support recommended by the manufacturer or supplied with this product. Carefully follow the installation instructions and use the adequate tools. Always ensure this unit is firmly fixed to avoid vibration and slipping while operating as it may result in physical injury. 7 - Ceiling or wall installation : Please contact your local dealer before attempting any ceiling or wall installation. 8 - Ventilation : Please contact your local dealer before attempting any ceiling or wall installation. 9 - Heat exposure : Sustained contact or proximity with warm surfaces may cause overheating and product damages. Please keep this product away from any heat source such as a heaters, amplifiers, hot plates, etc... This product can only be operated according to a very specific voltage. These information are specified on the label located at the rear of the product Power cords protection: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at lugs, convenience receptacles and the point where they exit from the fixture Cleaning precautions : Unplug the product before attempting any cleaning operation. This product should be cleaned only with accessories recommended by the manufacturer. Use a damp cloth to clean the surface. Do not wash this product Long periods of non use : Disconnect the unit s main power during long periods of non use Liquids or objects penetration : Do not let any object penetrate this product as it may result in electric shock or fire. Never spill any liquid on this product as it may infiltrate the electronic components and result in electric shock or fire This product should be serviced when : Please contact the qualified service personnel if : - The power cord or the plug has been damaged. - Objects have fallen or liquid has been spilled into the appliance. - The appliance has been exposed to rain or water. - The product does not appear to operate normally. - The product has been damaged Inspection/maintenance : Please do not attempt any inspection or maintenance by yourself. Refer all servicing to qualified personnel Operating environment : Ambient temperature and humidity: C, relative humidity must be less than 85% (when cooling vents are not obstructed). Do not operate this product in a non-ventilated, very humid or warm place. 3

4 English airled-9x3tcb - Battery-operated wireless projector with RGB LEDs 2 - Main characteristics This is a unique battery-operated projector. Its infrared remote control and battery allow you to install it anywhere and launch its built-in programs to create a perfectly autonomous light show. It also features an AirDMX receiver/transmitter allowing you to wirelessly and remotely synchronise projectors. It is equipped with 9x3W LEDs to produce an incredible colour rendering without lamp changing, but always low power consumption and a very long lifespan. Housing and materials: - Black metal housing - Double hanging/mounting bracket - Rear display - Internal thermal protection Functions: - Built-in drop down display to: Configure the DMX address Choose the number of channels 2, 3, 4, 5 or 6 channels Step/Fade programs selection Choose the preset colours Slave mode Music-sensitive mode with mic sensitivity settings Customise the 20-step user program - Infrared remote control to remotely access all the functions 3 - Technical specifications Projector specifications 9x3W LEDs 3W RGB LEDs hours Beamwidth: 40 Light output: 1160 Lux at 3 metres DMX input/output via XLR IEC power input/output (daisy-chain up to 10 projectors) 7-channel AirDMX wireless receiver/transmitter Averange range of 100m in open space Frequency range: GHz ISM Compatible with the AirBox-ER1 Integrated 21-cell lithium-ion battery. Full charge : approximately 5 hours Autonomy : approximately 56 hours at full power and approximately 9 hours with colour changes Package contents: The package must contain the following articles: The projector The user guide A double mounting bracket An infrared remote control An IEC 2 pole + earth power cord Power consumption: 66W Power supply: 100/240V, AC - 50/60Hz Thermo-regulated cooling system Dimensions: 200 x 200 x 148 mm Net weight: 4.5 kg Dimensions

5 airled-9x3tcb - Battery-operated wireless projector with RGB LEDs English 4 - Descriptio 5 4 POWER OUT Function Display DMX IN 12 POWER IN MODE SET UP UP DOWN AC 100V-240V 60-50Hz DMX OUT WIRELESS INDICATOR ID SELECTOR BATTERY WIRELESS DMX ON OFF ON OFF RED GREEN YELLOW BLUE PURPLE CYAN WHITE TRANSMITTER ID WIRELESS INDICATOR COLOR 6 10 POWER ON OFF FUSE : 1A 11 ANTENNA Power input/output sockets Allow you to connect the projector to an electrical outlet and daisy chain several projectors. Caution: Do not accumulate more than 700W on the same electrical outlet. 2 Menu buttons MODE / ESC button Allows you to access menus and select a function. SETUP / ENTER button Allows you to configure the parameters of the functions chosen with the MODE button. UP and DOWN buttons Allow you to increase/decrease the adjustable values or browse the submenus. 3 DMX input 3-pin female XLR plug hardwired as follows : - Mass: 1 - Negative signal: 2 - Positive signal: 3 This socket is used to receive a DMX signal from another projector or from a DMX console. 4 DMX output 3-pin male XLR plug hardwired as follows : - Mass: 1 - Negative signal: 2 - Positive signal: 3 Use this socket to daisy chain projectors 5 Display This intuitive display allows you to configure your projector. Please refer to the next paragraphs for more details about the projector configuration. 6 WIRELESS DMX Switch Activates the wireless DMX function. Once activated, the airled-9x3tcb is able to receive and transmit DMX signals via WiFi. 7 BATTERY Switch Allows you to configure the battery. - When OFF, the battery is disconnected. - When ON, the projector is powered by the battery. If ON, please make sure the POWER switch is not ON and the projector is not plugged to an electrical outlet. 5

6 English airled-9x3tcb - Battery-operated wireless projector with RGB LEDs 8 Antenna WiFi antenna. Pull out this antenna when you are using the wireless DMX mode in order to get a better range. 9 POWER Switch Turns the projector ON/OFF. Note : The projector will not use the battery if this switch is on and it is connected to an electrical outlet. 10 Main fuse If need to replace the fuse, please make sure the new fuse has exactly the same characteristics as the original one. 11 LED WIRELESS INDICATOR This LED flashes in red when the wireless DMX function is activated. It also allows you to visualise which channel is currently used. 12 ID SELECTOR button Allows you to choose a channel for the airled- 9x3TCb to communicate with other devices. 7 channels are available. The LED WIRELESS INDICATOR has a different colour for each channel. Refer to paragraph 6.2 for more details. 5 - Internal menu Description of the submenus MODE ESC SETUP ENTER UP and DOWN Action 2 channels : macros and dimmer 3 channels : R, G and B DMX MODE DMX mode selection 4 channels : R, G, B and Dimmer/Strobe (flashes in the absence of signal) 5 channels : R, G, B, Dimmer and Strobe 6 channels : R, G, B, Dimmer, Strobe/Speed and Macros Address DMX address settings Strobe Strobe speed: S.000 = no strobe ; S.100 = full speed AUTO MODE Mic SU.00 = min sensitivity ; SU.31 = max sensitivity Red: 0-100% Green: 0-100% MANUAL MODE Blue: 0-100% Strobe Strobe speed: S.000 = no strobe ; S.100 = full speed SLAVE MODE Slave mode activation SLon = Slave mode activated SLoF = Slave mode deactivated Selection Choose one of the 5 colours and 10 sequences FIXED COLOURS MODE Strobe Speed Strobe speed: S.000 = no strobe ; S.100 = full speed Sequencing speed. SP.00 = no sequencing >> SP.99 = full speed 6

7 airled-9x3tcb - Battery-operated wireless projector with RGB LEDs English STEP sequencing CROSSFADE sequencing User program playing and edition User program steps programmation Remote control Speed Strobe Speed Strobe Play / Stop Duration Fade time Strobe Dimmer Number of steps Step selection Red Green Blue Remote control activation Step sequencing speed: SP.00 = no action >> SP.99 = full speed Strobe speed: S.000 = no strobe >> S.100 = full speed Crossfade sequencing speed: SP.00 = no action >> SP.99 = full speed Strobe speed: S.000 = no strobe >> S.100 = full speed PLAY = Plays the program / STOP = Stops the program Configures the duration of each step. t.001 = 0.1 second / t.255 = 25.5 seconds Configures the crossfade duration between each step. F.000 = no crossfade / F.100 = max crossfade Configures the strobe speed for all the steps. S.000 = no strobe / S.100 = Strobe at full speed Configures the main dimmer for all the steps. D.000 = Black-out / D.255 = Full power Allows you to choose the number of steps of the user program. From 1 to 20 steps. Allows you to choose the scene you want to modify. From 1-20 steps. (Depending on the number of steps previously determined) Configures the red levels for the chosen step Configures the green levels for the chosen step Configures the blue levels for the chosen step rc.on : The infrared remote control is activated rc.of : The infrared remote control is deactivated Battery More details about colours and macros Black-out Red: R255 - V000 - B000 Orange : R255 - V070 - B000 Yellow: R255 - V100 - B000 Green: R000 - V255 - B000 Cyan: R000 - V255 - B255 Blue: R000 - V000 - B255 Pink: R255 - V000 - B100 Displays the real battery charge level from 0-100% Magenta: R255 - V000 - B100 Cool white: R255 - V255 - B255 Warm white: R255 - V255 - B100 Macro 1: step Macro 2: crossfade Macro 3: crossfade Macro 4: crossfade Macro 5: crossfade Macros behaviour Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 8 fixed colours sequencing (Red, Orange, Yellow, Green, Cyan, Blue, Magenta, and Pink). Step transitions. Non-stop crossfade from Green to Blue Non-stop crossfade from Red to Orange Same sequencing as macro 1 with crossfade transitions Non-stop crossfade from Warm white to Cool white 7

8 English airled-9x3tcb - Battery-operated wireless projector with RGB LEDs 6 - Advanced functions Charging the battery To charge the battery, plug your projector to an electrical outlet and the the POWER and BATTERY switches to ON. The display flashes during charging operations and the number of bars indicate the charge level. The different charge levels are as follows: 1 - : Battery level between 75% and 100%. 2 - : Battery level between 50% and 75%. 3 - : Battery level between 25% and 50%. 4 - : Battery level below 25%. The battery must be urgently charged since the projectors shuts off before the battery being fully discharged. The display stops flashing when the battery is fully charged. When using the battery, the display lights on and the first bar quickly flashes to indicate the battery level is below 25% and the projector might automatically switch off soon Using the wireless DMX mode (AirDMX) The WiFi transmission system allows you to synchronise several units without using any DMX cable. You can synchronise several units by using the master/slave mode or like any regular DMX daisy-chaining installation. The units must use the same communication channel to be synchronised. To do so, use the ID SELECTOR button and choose one of the 7 available channels. The LED WIRELESS INDICATOR will light on with a different colour for each channel. You will find below the channels and their corresponding colour: Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 Red Green Yellow Blue Purple Cyan White The LED WIRELESS INDICATOR has 3 different status when the units are communicating: 1 - LED constantly on : No DMX or WiFi signal. 2 - LED flashing in red : The projector is currently transmitting a signal. 3 - LED flashing in green : The projector is currently receiving a signal. Note : The unit transmitting a DMX signal is in transmission mode Using the USER mode (customisable program) Editing the program Go to the Edit menu by pressing MODE, then press SETUP. 1 - Use the SC.XX submenu to configure the number of steps of the program. 2 - Use the St.XX submenu to edit the first scene: St.01, then configure the red, green and blue levels with the r.xxx, g.xxx and b.xxx submenus. 3 - Press St-XX to move onto the next step. The number of customisable steps depends on the choice you made with the SC.XX submenu. (The menu goes back to step 1 each time a step is edited.) 4 - Repeat steps 2 and 3 as many times as you have steps to edit Program settings Use the MODE button to reach the USer menu, then press SETUP. 1 - Use the PLAY/STOP submenu to launch or stop the program. 2 - Use the t.xxx submenu to configure the duration of the steps. 3 - Use the F.XXX submenu to configure the crossfading. 4 - Use the S.XXX submenu to configure the strobe speed. 5 - Use the d.xxx submenu to configure the main dimmer. Note : Settings from the USER menu affects all the program steps. 8

9 airled-9x3tcb - Battery-operated wireless projector with RGB LEDs English 7 - The various DMX channels channel mode CHANNEL 1 CHANNEL 2 DMX values Effect DMX values Effect Off Red Orange Yellow Green Cyan Blue Pink Magenta Dimmer from 0-100% Cool white (6000 K) Warm white (3200 K) Colour macro Colour macro Colour macro Colour macro Colour macro Music-sensitive mode Note : - Colour macros are described in paragraph The music-sensitive mode is a sequence of the 10 preset colours in a loop channel mode Mode 4 canaux DMX values Effect CHANNEL Red from 0-100% CHANNEL Green from 0-100% CHANNEL Blue from 0-100% channel mode DMX values Effect CHANNEL Red from 0-100% CHANNEL Green from 0-100% CHANNEL Blue from 0-100% CHANNEL Main dimmer from 0-100% Slow to fast strobe Full power DMX values Effect CHANNEL Red from 0-100% CHANNEL Green from 0-100% CHANNEL Blue from 0-100% CHANNEL Main dimmer from 0-100% CHANNEL No function Slow to fast strobe 9

10 English airled-9x3tcb - Battery-operated wireless projector with RGB LEDs channel mode CHANNEL 6 CHAN. 5 CHAN. 4 CHAN. 3 CHAN. 2 CHAN. 1 MODE DMX value Function Black-out No strobe Blue ( ) From 0-100% Green ( ) From 0-100% Red ( ) From 0-100% Red Orange Yellow Green Cyan Blue Pink Magenta Cool white (6000 K) Strobe ( ) From slow to fast - From 0,1Hz to 20Hz Main dimmer ( ) From 0-100% No function No function No function Warm white (3000 K) Macro Macro Macro Macro 4 Speed ( ) From slow to fast Macro Music-sensitive sequence Mic sensitivity Note : - Colour macros are described in paragraph The music-sensitive mode is a sequence of the 10 preset colours in a loop. 10

11 airled-9x3tcb - Battery-operated wireless projector with RGB LEDs English 7 - Infrared remote control The infrared remote control supplied with the projectors allows you to remotely access all the functions of the projectors. The infrared sensor is located on the front of the projector. Note : The remote control can also be used when the projector is in DMX mode. 1 - Black out button: Turns the projectors ON or OFF. 2 - A (AUTO RUN) button: Activates the automatic mode. Automatic colour changes. 3 - PROG (SELECT PROG) button: Launches built-in programs. Select a program among the 10 fixed colours selections (red, green, cyan...), Color Jumping (fast colour sequencing) and Color Dream (slower colour sequencing) by pressing the + and - buttons. Note : Fixed colours can also be chosen with the 0 to 9 buttons. The sequencing is as follows: 0 = black-out ; 1 = Red ; 2 = Green ; 3 = Blue ; 4 = Orange ; 5 = Yellow; 6 = Magenta, 7 = Cyan, 8 = Cool white and 9 = Warm white. 4 - F button (FLASH): Activates or deactivates the Flash mode. Increase or decrease the flash speed with the + and - buttons of the remote control. 5 - SP button: Allows you to configure the Color Jumping and Color Dream programs speed. Increase or decrease the speed with the + and - buttons of the remote control. 6 - D button (DMX MODE): Activates the DMX mode of the projectors. 7 - DMX mode selection There are 5 different DMX modes. You will need to select a DMX mode before controlling your projector in DMX mode ; Press the D button (DMX MODE) and use the + and - buttons to switch from one mode to another : - When the LEDs are red, the projector is currently using the 2-channel mode. - When the LEDs are green, the projector is currently using the 3-channel mode. - When the LEDs are blue, the projector is currently using the 4-channel mode. - When the LEDs are red and green, the projector is currently using the 5-channel mode. - When the LEDs are red and blue, the projector is currently using the 6-channel mode. 8 - SA button: Activates the music-sensitive mode. 9 - SL button (SLAVE): Activates the slave mode SET ADDR buttons and 0, 1, 2, 3, 4, 5, 6, 7, 8 and 9: Allows you to configure your projectors DMX address. For instance, if you want to configure the address 245 : - Press S, all the LEDs are flashing to indicate the beginning of the process. - Press 2, the green LEDs of your projectors lit up to indicate the hundreds digit has been saved. - Press 4, the blue LEDs of your projector lit up to indicate the tenths digit has been saved. - Then press 5. All the LEDs will flash to confirm you the address has been saved properly. To configure the address 002: - Press S, all the LEDs are flashing to indicate the process beginning. - Press 0, the green LEDs of your projectors lit up to indicate the hundreds digit has been saved. - Press 0, the blue LEDs of your projector lit up to indicate the tenths digit has been saved. - Then press 2. All the LEDs will flash to confirm you the address has been saved properly R, G and B buttons : Adjusts colours brightness, R for red, G for green and B for blue. Increase or decrease their brightness with the + and - buttons. 11

12 Because CONTEST takes the utmost care in its products to make sure you only get the best possible quality, our products are subjects to modifications without prior notice. That is why technical specifications and the products physical configuration might differ from the illustrations. Make sure you get the latest news and updates about the CONTEST products on CONTEST is a trademark of HITMUSIC S.A. - Zone Cahors sud FONTANES - FRANCE