Thank you for your purchase. lease follow the instructions below for correct assembly. B dowel x0 x1 bolt x H height adjuster x1 bracket x Q clip x R locking nut x K seal x S F x shelf plugx8 x8 L hinge x T x U bolt x 1 nut x V W safety strap x1 x1 X Y wall anchor x1 wall x1 WR: ny furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. ccordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping.the fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from those supplied. Z x10 slide railx slide railx slide railx slide railx Hardware Supplied plastic wedge glide x x1 x1 washer x Wall Strap *We recommend using a Flathead driver to tighten all locking nuts 100% before first use. lease clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%. hillips & Flathead drivers and hammer required 1
1 ttach 1x bracket () to panel [] using x s (). ttach 1x bracket () to panel [] using x s (). Tighten with a driver. over each bracket with 1x clip () as shown. nsert x bolts () into panel []. nsert x bolts () into panel [].
Q Q R Q 7 x R R ttach x slide rails (Q) to panel [] and secure with 9x s (). ttach x slide rails (R) to panel [] and secure with 9x s (). Tighten with a driver. ttach 1x bracket () to each panel [7] using x s (). Tighten with a driver. over each bracket with 1x clip () as shown.
6 7 7 1 ttach both panels [7] between panels [] and [] using x dowels () and secure with x locking nuts (). Tighten with a driver. nsert 8x bolts () into panel [1] as shown.
8 7 9 1 0 9 ttach panel [1] to panels [], [], [] and [] using 8x dowels () and secure with 8x locking nuts (). Tighten with a driver. Slide down panels [9] and [0] between the grooves in panels [], [], [] and [] to form the back of the unit.
9 10 8 8 ttach 1x bracket () to panel [8] using x s (). Tighten with a driver. over the bracket with 1x clip () as shown. ttach panel [8] to the rest of the unit using 8x dowels () and 8x s () as shown. 6
11 1 H U 11 U U 1 nsure slot in nut is facing incoming bolt. U 8 10 10 11 ttach panels [10] and [11] together as shown using x nuts () and x bolts ().Tighten with a driver. ttach panels [10] and [11] to panel [8] using 10x s (). ttach support leg [1] to panel [8] as shown. Screw the height adjuster (H) onto the support leg [1]. ttach x plastic glides (U) to the legs using a hammer. 7
1 1 L K T: f the doors are uneven or there is a gap in the middle, loosen or tighten the on the door hinge until they are sitting flush. L 1 1 K L 1 L 1 ttach x hinges (L) to panel [1] using x s (), and attach 1x seal (K) and secure with 1x (). ttach x hinges (L) to panel [1] using x s (). ow attach 1x seal (K) and secure with 1x (). ttach door hinges on panels [1] and [1] to the unit using 16x s (). Tighten with a driver. nsure the doors open and close easily. 8
1 16 K 1 16 K 17 1 B K 18 16 17 1 B 19 T 16 B 17 B 1 16 f a clip () is not catching on the seal (K), adjust the magnetic end by twisting it outwards. S nsert x bolts () and attach 1x seal (K) using 1x () to panel [1]. ttach side panels [16] and [17] using x locking nuts (). Slide base panel [18] down between the grooves of the side panels. ttach back panel [19] using x s (B). Turn drawer upside down and attach 1x slide rail (T) and 1x slide rail (S) to the side panels using x s (). Tighten with a driver. 9
17 18 1 strap washer F F 1 V 6 1 F 6 nsert 8x shelf plugs (F) into the unit at the desired height for the shelves and rest the shelf panels [6] onto them. nsure the shelves are balanced and stable. nsert the three assembled drawers, ensuring they slide along the rails smoothly. 1 1 Z W 1 ttach 1x wedges (1) to the back of the unit as shown, and secure with 1x s (). ow attach 1x safety strap (V) to the back edge of panel [1] using 1x washer (Z) and 1x (W). Tighten with a driver. 10
19 0 strap washer wall plug X Z Y nce assembled lift furniture into place, do not drag. Use a drill to create a small hole lining up with the top of the safety strap (V). Fasten to wall using 1x wall plug (X), 1x washer (Z) and 1x (Y). nsure unit is balanced and steady before use. You re done, enjoy! 11