Assembly instructions
|
|
- Bridget Henry
- 5 years ago
- Views:
Transcription
1 Assembly instructions Model: MXR0024/KIT TV Aerial - 18 Element Kit Contact: Helpline: +44 (0) support@maxview.co.uk Web: Maxview reserve the right to change specifications without prior notice Iss 2
2 Pack contents check A B C D G E F H I J M K L N O P Q R S T U V A. Reflector Plate x 1 B. Support Arm x 1 C. Dipole x 1 D. Joining Plate x 2 E. Support Arm Bracket x 4 F. Washer x 4 G. M5 Nut x 4 H. M5 x 25mm Screw x 4 I. Screw x 1 J. Mast Clamp x 1 K. Rear Boom Assembly x 1 L. Front Boom Assembly x 1 M. Crank Mast x 1 N. 10m Coaxial Cable O. Coaxial Plug x 1 P. M5 x 35mm Bolt x1 Q. M5 25mm Bolt x 2 R. Screw x 4 S. Wall Plug x 4 T. Cable Clip x 8 U. M5 Nut x 3 V. Fixing Bracket
3 Assembly Join the 2 pieces of boom together using the joining plate, M5 x 25mm screws M5 nuts and 5mm Shake Proof Washers. Screw the Dipole firmly to the Boom. 3. Fit the support arm to boom of the aerial using the four joining plates. Secure with nuts and bolts. 4. Slide on and firmly push down the Reflector onto the groove of the Reflector Bung.
4 Connecting Coaxial Cable 1. 12mm 2. 18mm 28mm Using a sharp knife prepare the Coaxial Cable as shown. Loosen the screws on the 2 terminals in the Dipole. Feed the inner core to one of the terminals and the twisted braid into the other. Tighten screws and close Dipole Cap.
5 Fitting Coaxial Plug 1. Outer insulator Screw cap Braid Inner core Plug Inner insulator Claw 1. Cut cable to required length. 2. Unscrew coaxial plug and slide screw cap over cable. 3. Strip away approximately 23mm of outer insulation. 4. Gather strands of shielding braid together and wind back around the outer insulation. Remove foil shield. 5. Strip away about half of the inner insulation around inner core. Check that none of the shielding braid is touching the inner core. 6. Open claw, slide over screening braid and pinch to tighten. 7. Re-assemble connector and cut off inner core wire flush with plug.
6 Fixing Kit Installation Insert Mast into Fixing Bracket. Make sure the holes in the Mast align with the holes in the bracket. Insert nuts & bolts as shown and securely tighten using a 8mm spanner Mount bracket to a secure solid external wall or internal wooden beam using the screws and wall plugs if required. A 6mm drill bit will be required if using wall plugs.
7 3 Attach aerial to mast using the Mast Clamp.
8 Polarisation Tip: Look at outdoor aerials in your area to see which direction to point your aerial for best reception. (Note different model illustrated for example only) Aligning your aerial Horizontal mounting recommended for Main TV transmitters. Turn on your TV set. Refer to manufacturers instructions to tune your TV into the available digital/hd/3d channels. Select a tuned-in channel. Next, carry out the following procedures: 1. Turn your aerial to the LEFT until you lose the picture (if alone turn the volume up and turn until you hear a reduction in sound quality). 2. Remember this position and turn your aerial to the RIGHT until you lose the picture/sound again. 3. Now point the aerial in the centre of these two points and you will receive optimum reception. Digital & HD reception: Reception of digital terrestrial TV (DTT) signals is subject to: 1. Use with a DTT set top box or integrated TV with digital tuner/receiver 2. Satisfactory signal quality from DTT transmitter To receive terrestrial HD channels you will require the following: 1. An HD ready TV 2. Freeview HD receiver or TV with integrated Freeview HD tuner/receiver 3. HD signals must be transmitted in your local area. Visit for more information. Vertical mounting recommended for Relay TV transmitters. Safety warnings: > Before starting installation check structure is sound and check for hidden electrical wiring or plumbing. > When working on installations outside, beware of overhead power lines. > Observe safe working practices, tread carefully and ensure adequate lighting is available in loft/roof space. > Always follow manufacturer s operating and safety instructions before using tools and/or equipment. > Ladder safety - always read and follow the manufacturer s instruction label affixed to the ladder. > Ensure cable is correctly routed before fixing into position, taking care not to over tighten cable clips. > This product may contain small parts - keep out of reach of children. > After installation make regular maintenance checks. > If in doubt consult a qualified or professional aerial installer.
DLMP Installation Instructions
DLMP Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420 [ ] 2 x
More informationSatellite Dish Installation Manual (Ver. 2) 1
Satellite Dish Installation Manual Provided by DiscoverNet, Inc. Satellite Dish Installation Manual (Ver. 2) 1 Table of Contents Section 1: Introduction Page 3 Section 2: Recommended Tools and Materials
More informationDLMP-45/45R Installation Instructions
DLMP-45/45R Installation Instructions Tools Needed Posidrive No.3 Screwdriver Large Flat Head Screwdriver 2x 10mm Spanner 1x 13mm Spanner Ø8mm Drill Ø6mm Drill Kit Contents [ ] 1x Tube 2.5M long 17420
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationChapter 4. Dish Antenna Installation. Installing a DISH 500 Antenna. Finding the Satellites
These instructions guide you through the installation of a satellite system which includes your receiver (included with this manual), and a DISH Pro DISH 500 antenna system that can be identified by the
More informationHE INSTRUCTION MANUAL
Outdoor Antenna Kit Model Number: HE170351 INSTRUCTION MANUAL OUTDOOR ANTENNA KIT Warranty Details REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH
More informationRegister your product and get support at www.philips.com/welcome SDV8625T/27 User manual Contents 1 Important 4 Safety 4 For indoor use 4 For outdoor use 4 Notice for USA 4 Notice for Canada 5 Recycling
More informationTurret Replacement Instruction Manual
Automatic Multi-Satellite TV Antenna Turret Replacement Instruction Manual for models RPSKLGL, RPSKSML, SK-LG00, SK-SM00, & RP-SWM For help, email help@winegard.com or call -800-788-7 568 Raising the Antenna
More informationA449-6S 70 CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-6S 70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951425 (7/93) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN
More informationCable ISOBUS Active Termination
ISOBUS Retrofit Kit Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity ISOBUS Retrofit Kit 4100843 1 Hex Head Bolt
More information75 Elliptical Antenna System
Instruction and Assembly Manual 75 Elliptical Antenna System 7291 NW 74th Street Miami, FL 33166 GlobeCast Technical Service: (888) 988-5288 Manufactured By: 2002 Channel Master LLC Printed in U.S.A. 8000915-02
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: LPDA 200 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationCoyote popup display set up instructions
Coyote popup display set up instructions Frame 1 2 3 Prepare frame for assembly by locating the purple hooks on top of the frame. Stretch frame to size, snapping magnetic locking arms together. Attach
More informationASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES
ASSEMBLY, INSTALLATION, AND REMOVAL OF CONTACTS AND MODULES FOR 75 OHM AND 75 OHM HD COAXIAL CONTACTS AND MODULES Table of Contents SECTION 1 RECEIVER CONTACT ASSEMBLY INSTRUCTIONS SECTION 2 ITA CONTACT
More informationA CENTIMETER FM YAGI ANTENNA MHz
ASSEMBLY AND INSTALLATION A449-70 CENTIMETER FM YAGI ANTENNA 440-450 MHz COMMUNICATIONS ANTENNAS 951424 (10/91) WARNING THIS ANTENNA IS AN ELECTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DEATH
More informationM2 Antenna Systems, Inc. Model No: 23CM35
M2 Antenna Systems, Inc. Model No: 23CM35 SPECIFICATIONS: Model... 23CM35 Frequency Range... 1250 To 1300 MHz *Gain... 20.94 dbi Front to back... 25 db Typical Beamwidth... E=17 H=18 Feed type... Folded
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: MOD 550 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont,
More informationTV55. Owner s Manual. Indoor/Outdoor Amplified TV Antenna
Owner s Manual Indoor/Outdoor Amplified TV Antenna Safety Precautions Warning! Use extreme caution when installing or removing an outdoor antenna that is located close to overhead wires such as power lines,
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS FROM 300 cm. UP TO 450 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system
More informationWINEGARD. TRAV LER Automatic Multi-Satellite TV Antenna. Model SK-3003 DIRECTV TRIPLE FEED INSTALLATION MANUAL. Made in the U.S.A.
WINEGARD TRAV LER Automatic Multi-Satellite TV Antenna Model SK-3003 DIRECTV TRIPLE FEED MANUAL Made in the U.S.A. SK-3003 Winegard Company 3000 Kirkwood St. Burlington, IA 52601-2000 319/754-0600 FAX
More informationTV Lift System Model CL-65 Installation Instructions
TV Lift System Model CL-65 Installation Instructions Contact: Support@Nexus21.com Toll Free: (866) 500-5438 Phone: (480) 951-6885 Fax: (480) 951-6879 Revised: 01/17/17 Below is a parts list describing
More informationDigital Modulator Instructions
Product Code: CCT818 ANTIhum.com Digital Modulator Instructions Features Tunable output channel from 21-69, Push button channel selection, Microprocessor tuning, Channel Memory, Audio input, LED channel
More information2178-L/S Series Fiber Optic Splice Case with Gasket
2178-L/S Series Fiber Optic Splice Case with Gasket Instructions for: 2178-S Splice Case 2178-LS Splice Case 2178-LL Splice Case 2181-LS Cable Addition Kit May 1997 34-7041-9949-5-A 1 Table of Contents
More information3M Distribution Box (DDB)
3M Distribution Box (DDB) Merged Copper and Fiber Pole/Post Mount Enclosure Installation Instructions November 2015 78-0015-2736-1-A 2 November 2015 78-0015-2736-1-A Contents 1.0 General 2.0 Enclosure
More informationB2590/65SNZ. Crank-Up. Installation & Operation Instruction Manual NZ Iss 1
B2590/65SNZ Crank-Up Installation & Operation Instruction Manual 9111410NZ Iss 1 Useful Information Date of Purchase Retailer Installer Serial Number Contents Warranty P3 Safety Precautions P4 Introduction
More information3 SLiC Aerial Closure with Rubber End Seal
3 Aerial Closure with Rubber End Seal Instructions 1.0 General 1.1 This instruction bulletin describes the assembly of the 3M Aerial Closure with external bonding hanger brackets. These closures are suitable
More informationELLIPTICAL ANTENNA E0851B11
ELLIPTICAL ANTENNA E0851B11 INSTALLATION GUIDE E0851B11 Installation Manual Step 1: Finding a suitable antenna site A suitable antenna site requires an unobstructed view and a stable antenna mounting surface.
More informationGAP SUPER C ANTENNA. Installation and Assembly Instructions. GAP Antenna Products, Inc. 99 North Willow St Fellsmere, FL (561)
GAP SUPER C ANTENNA Installation and Assembly Instructions GAP Antenna Products, Inc 99 North Willow St Fellsmere, FL 32948 (561) 571-9922 WEBSITE http://www.gapantenna.com SAFETY NOTICE WARNING POWER
More informationInstallation instructions, accessories. Subwoofer. Volvo Car Corporation Gothenburg, Sweden. Page 1 / 29
Installation instructions, accessories Instruction No 30752136 Version 1.1 Part. No. 30752135 Subwoofer Volvo Car Corporation Subwoofer- 30752136 - V1.1 Page 1 / 29 Equipment A0000162 A0000161 A0801178
More informationNava Buffet Assembly Instructions
Thank you for your purchase. lease follow the instructions below for correct assembly. B dowel x0 x1 bolt x H height adjuster x1 bracket x Q clip x R locking nut x K seal x S F x shelf plugx8 x8 L hinge
More informationIndustrial Monitor Update Kit
Industrial Monitor Update Kit (Bulletin Number 6157) Installation Instructions 2 Table of Contents Table of Contents Industrial Monitor Update Kit... 3 Overview... 3 Part 1 - Initial Preparation... 5 Part
More informationMUK REAR PANEL ASSEMBLY ASSEMBLY INSTRUCTIONS
Rev B. 13 August 2017 ASSEMBLY INSTRUCTIONS The Midnight Ultimate Keyer (MUK) consists of two functional assemblies: Rear Panel containing the interface and power connectors. Front Panel containing the
More informationFOSC 450 C6 and D6 Closures
FOSC 450 C6 and D6 Closures I N S T A L L A T I O N I N S T R U C T I O N Fiber Optic Splice Closure 1. General Product Information The FOSC 450 C6 and D6 fiber optic splice closures use compressed gel
More informationInstructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16)
Satellite multiswitch Instructions for Use P.154-UP (9/4) P.155-UP (9/8) P.150-UP-12 (9/12) P.150-UP-16 (9/16) EMP-CENTAURI is a registered trademark Dear Customer, Thank you for buying the EMP-Centauri
More informationInstructions for Use P.160-AP-8 (13/8) P.160-CP-8 (13/8) P.160-CP-12 (13/12) P.160-CP-16 (13/16)
Satellite multiswitch Instructions for Use P.160-AP-8 (13/8) P.160-CP-8 (13/8) P.160-AP-12 (13/12) P.160-CP-12 (13/12) P.160-AP-16 (13/16) P.160-CP-16 (13/16) EMP-CENTAURI is a registered trademark Dear
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used
More informationCellular Signal Booster
Drive 4G-X Cellular Signal Booster THE ALUMINUM CASING OF YOUR SIGNAL BOOSTER!! WILL ADJUST TO THE TEMPERATURE OF ITS ENVIRONMENT, BUT IS DESIGNED TO PROTECT THE SIGNAL BOOSTER TECHNOLOGY. FOR EXAMPLE,
More informationINSTRUCTION MANUAL. Model V-4R Collinear Gain Vertical for MHz. General SPECIFICATIONS
308 Industrial Park Road Starkville, MS 39759 USA, Ph: (662) 323-9538 FAX: (662) 323-651 Model V-4R Collinear Gain Vertical for 420-450 MHz INSTRUCTION MANUAL General The new Hy-Gain V-4R 70cm antenna
More informationSCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width
SCREEN WINCH SYSTEM INSTALLATION MANUAL FOR SCREENS UP TO 300 cm. of width Before installing the screen winch system, please read the following instructions carefully: The screen winch system must be used
More informationCheck what you have received against the component checklist and hardware above.
SSS SSPW SSW SSPB SSB Component Checklist Installation Instructions SYSTEMA Systema Monitor Spring Arm HARDWARE Display Mounting Spacers (x4) 3/4mm Allen Keys Display Mounting Screws M4 x 14mm (x1) Silver
More information18mm ECAM Cable Entry Port
18mm ECAM Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 18mm ECAM (External Cable Assembly Module) Cable Entry Port Kit is designed to accept fiber optic cables with external diameters
More informationLWX-1. Satellite Weather Radio Module Installation Instructions A
LWX-1 Satellite Weather Radio Module Installation Instructions 988-0158-13A Copyright 2009 Navico All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed
More informationAUDIO ROOF KIT P/N , , APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6
AUDIO ROOF KIT P/N 2882064, 2882065, 2882066 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationINSTALLATION GUIDE FOR THE MOTOR
INSTALLATION GUIDE FOR THE MOTOR Motor Horizon-Horizon ref 450907 MET542 This symbol indicates that the product must not be treated as household waste. The harmfull substances possibly contained in the
More informationCheck what you have received against the component checklist and hardware above.
SA46S SA46W SA46B SA46PB Component Checklist Installation Instructions SYSTEMA Systema Monitor Arm 460mm HARDWARE Display Mounting Spacers (x4) Display Mounting Screws Arm Assembly VESA monitor head M4
More informationSnail Fence InteleCell Deployment Guide
Snail Fence InteleCell Deployment Guide Preparation 1. Prepare deployment trip by making sure you have the following materials and tools when you fly up to the site: InteleCell NEMA Enclsoure (grey plastic
More informationWaterVue TV Installation & User Manual
WaterVue TV Installation & User Manual 19 Waterproof TV Dimensions of TV Front screen 486mm x 340mm x 3mm Mounting Plate 467mm x 324mm x 48mm 24 Waterproof TV Dimensions of TV Front screen 576mm x 395mm
More information2100/2200/4100/6200 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors
00/00/400/600 & MPB Series Bottom Mount Drive Pack. for Standard Load Parallel Shaft 60 Hz Gearmotors Installation, Maintenance & Parts Manual DORNER MFG. CORP. INSIDE THE USA OUTSIDE THE USA P.O. Box
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual. ver 3.0.
ver 3.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationAssembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door
CHAPTER 8 Assembling and Mounting the Presentation Display, Speakers, Speaker Screens, and Table Door July 13, 2012, This document provides you with the procedures you perform to assemble and mount the
More informationTV44. Owner s Manual. Amplified/Outdoor Satellite Dish Clip-on Antenna
TV44 Owner s Manual Amplified/Outdoor Satellite Dish Clip-on Antenna Safety Precautions 1 Warning! Use extreme caution when installing or removing an outdoor antenna that is located close to overhead wires
More informationOWNER'S MANUAL SIGNAL COMMANDER
OWNER'S MANUAL SIGNAL COMMANDER THIS MANUAL CONTAINS INSTRUCTIONS FOR: LPDA 100 - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DIAGRAM - WARRANTY AntennaTek, Inc. 425 S. Bowen, # 4 Longmont,
More informationAutomatic Connector MHV Connectors MHV Introduction MHV series connectors Contents Polarized mating interfaces Anti-Rock mating interfaces
Automatic s 2004 Automatic. All rights reserved. pdf 1.0 3-18-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable Plugs...................
More informationInstallation Manual Wall Mounting
Installation Manual Wall Mounting EN FR IT NL CZ PL DigiDish 33 DigiDish 45 Satman 33 Satman 45 Multytenne 45 EN FR IT Dear customer, thank you for purchasing one of the quality products produced by TechniSat.
More informationMobile TV & Radio Reception Products
Mobile TV & Radio Reception Products HGV & Commercial Vehicle Product Range Pack contents. Available in grey or white. Europe s best selling Omni-directional aerial B2344 Omnimax Pro The Omnimax Pro is
More informationNava Entertainment Unit Assembly Instructions
ava ntertainment nit ssembly nstructions Thank you for your purchase. Please follow the instructions below for correct assembly. B dowel x2 x8 H locking nut x22 Q x32 x10 x10 K bracket x P bolt x22 height
More information3M Better Buried Closures
3M Better Buried Closures Instructions March 2016 78-0015-2945-8-A Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Closure Selection Guide... 4 4.0 LHS End Cap Installation... 5 5.0 Cable Preparations...
More informationHCS - HES Cabling Systems
HCS - HES Cabling Systems Installation Manual for HCS High-Capacity Fiber-Optic Rack-Mount Cabinets Be sure to read and completely understand this procedure before applying product. Be sure to select the
More informationHN Connectors. Automatic Connector. Introduction. Contents. 631/ FAX 631/
Connectors Introduction 2004 Automatic Connector. All rights reserved. pdf 1.0 4-13-04 Contents Specifications........................... 2 Straight Cable Plugs...................... 3 Right Angle Cable
More information3M Fiber Optic Wall Mount Enclosure 8430 Series
3M Fiber Optic Wall Mount Enclosure 8430 Series Installation Instructions January 2014 3 78-0013-9429-1-A Table of Contents 1.0 Description...3 2.0 Parts...4 3.0 Assembly...4 4.0 Mounting the Enclosure...6
More informationASSEMBLY AND INSTALLATION 3 ELEMENT 6 METER BEAM
ASSEMBLY AND INSTALLATION A50-3S 3 ELEMENT 6 METER BM COMMUNICATIONS ANTENNAS 951364 (12/94) WARNING THIS ANTENNA IS AN ELTRICAL CONDUCTOR. CONTACT WITH POWER LINES CAN RESULT IN DTH, OR SERIOUS INJURY.
More information3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462-FN and 3M High Gel Re-enterable Encapsulant 8882)
3M Better Buried Closure (with 3M Scotchlok Shield Bond Connector 4462FN and 3M High Gel Reenterable Encapsulant 8882) Instructions April 2016 78813509979C Contents: 1.0 General... 1 2.0 Kit Contents...
More information2178 Fiber Optic Splice Case and 2181 Cable Addition Kit
2178 Fiber Optic Splice Case and 2181 Cable Addition Kit Instructions January 1994 Issue 1, 34-7029-6387-6 1 2 Contents: 1.0 General... 4 2.0 Specifications... 4 3.0 Kit Contents... 5 SECTION 1: 2178 Splice
More informationFully ly Automaticti. Motorised Satellite t TV System. User s manual REV
REV. 1.0 Fully ly Automaticti Motorised Satellite t TV System User s manual Customer Help Line: 1300 139 255 Support Email: support@satkingpromax.com.au Website: www.satkingpromax.com.au www.satkingpromax.com.au
More informationGENUINE PARTS CAUTION
GENUINE PARTS SATELLITE RADIO INSTALLATION INSTRUCTIONS 1. DESCRIPTION: SATELLITE RADIO SYSTEM 2. PART NUMBERS: XM tuner kit 999U9-NV003 XM antenna kit 999U9-VR000 Sirius tuner kit 999U9-NV004 Sirius antenna
More information3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx Preparing drop cable with micro-tubes
FIST-GCOG2-Dx24 I N S T A L L A T I O N I N S T R U C T I O N FTTH closure for micro-tubes and micro-cables Content 1 Introduction 2 Kit content 3 Closure preparation 3.1 Work-stand 3.2. Opening FIST-GCOG2-Dx24
More informationTFT-150R-G. Tape Shield Cable (page 2) Suggested Installation Equipment (not supplied with kit) Wire Shield Cable (page 7)
TFT-150R-G 5-15kV Cold Applied Indoor (5-8kV Indoor and Outdoor) Termination for Copper Tape, Wire Shield, Lead Sheath, and UniShield Cable Suggested Installation Equipment (not supplied with kit) Cable
More informationLANmark PCB patch panel, 1HU INSTALLATION GUIDE. LANmark PCB patch panel, 1 HU
LANmark PCB patch panel, 1HU INSTALLATION GUIDE LANmark PCB patch panel, 1 HU Document information Document reference Release September 2001 Published by Contact address BRO-009 LANmark PP 1HU 0701 Nexans
More informationSite Installation Model MP-8433
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationSite Installation Model MP-8424
Site Installation Model MP- Rev. //0 SCOREBOARD SITE INSTALLATION INSTRUCTIONS CAUTION: All American Scoreboards (AAS) recommends the sign be installed by a licensed contractor, and must meet all local
More informationE4200 Antenna Installation Instructions: 1. Soldering required (here is the list of tools you will need)
Thank you for purchasing the 6 Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. Next we will teach you how to setup the DD-WRT firmware which
More informationReplacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly
Replacing the PanelMate epro PS, PanelMate epro PS EE, and PanelMate epro PS OD 7685x-12 Series Backlight Assembly Introduction The Backlight Replacement Kit provides a replacement backlight for the PanelMate
More informationPower Rack with Lat Pull
Power Rack with Lat Pull BD-7 Owner's Manual VA0900 D SAFETY & PRECAUTIONS IMPORTANT: READ ALL PRECAUTIONS CAREFULLY BEFORE USING THIS PRODUCT. RETAIN OWNER'S MANUAL FOR FUTURE REFERENCE. Note: This item
More informationTECHNICAL GUIDE. TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L
TECHNICAL GUIDE TOUGH GUN ThruArm G1 Series Robotic MIG Guns for FANUC Robots 100iC, 100iC-12, 100iC-6L, 100iC-7L, 120iC, 120iC-10L, 120iC-12L INSTALLATION MAINTENANCE TECHNICAL DATA OPTIONS EXPLODED VIEW
More informationDLP ANTENNA INSTRUCTION MANUAL. Dielectric LLC 22 Tower Road Raymond, Maine Phone:
DLP ANTENNA INSTRUCTION MANUAL Dielectric LLC 22 Tower Road Raymond, Maine 04071 Phone: 800-341-9678 TABLE OF CONTENTS Section Title Page Warnings 1 Return Policy. 1 Factory Tests... 1 Antenna Description....
More informationInstallation Overview
Installation Overview Overview This chapter presents cable preparation and installation procedures for coaxial cables. Many connectors and special-purpose installation tools required for these cables are
More informationPC-250. SMD Taped Parts Counter Operator s Manual. ISO 9001:2008 Certified. V-TEK, Incorporated 751 Summit Avenue Mankato, MN USA
PC-250 SMD Taped Parts Counter Operator s Manual ISO 9001:2008 Certified V-TEK, Incorporated 751 Summit Avenue Mankato, MN 56001 USA (P) 507-387-2039 (F) 507-387-2257 www.vtekusa.com Dear Customer: All
More informationUser Guide SiriUS ConneCt tuner
User Guide Sirius ConneCt TUNER Congratulations on your purchase of the SIRIUS Connect SCH1P2 Satellite Radio Tuner! Your new SCH1P2 SIRIUS Connect Satellite Radio Tuner is designed to work with SIRIUS-Ready
More informationHome Signal Distribution Kit SXHDK2. Installation Guide
Home Signal Distribution Kit SXHDK2 Installation Guide Table of Contents Introduction.................................................... 3 Safety and Care Information.... 4 What s in the Box?... 5 Combiner
More informationOptical Distribution Box 300 Installation Guide. Version : R0.0
Optical Distribution Box 300 Installation Guide Document No. : OD16-546-L-01 Version : R0.0 Date: 21-Mar-2018 IMPORTANT INSTRUCTIONS When using fiber optic equipment, basic precautions should always be
More information2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table
FIST-GCO2-F INSTALLATION INSTRUCTION GCO2-FC GCO2-FD Content 1 Introduction 2 General 2.1 Kit Contents 2.2 Elements needed from the FIST installation kit 2.3 Tools 2.4 Cable preparation table 3 Installation
More information18W Low Energy Dusk-Dawn Bulkhead E-290B
18W Low Energy Dusk-Dawn Bulkhead E-290B INSTALLER GUIDE V1.0-12/06 IQ-ABH01-PH-18-PR IQ Europe Limited Sandbeck Lane, Wetherby LS22 7TW. Visit us at www.iq-europe.co.uk Installation helpline 0871 717
More informationElectric Wall/Ceiling Projection Screen Saker Series User s Guide
Electric Wall/Ceiling Projection Screen Saker Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen s Black
More informationGrowmaster Assembly Instructions
Growmaster ssembly Instructions Item No. Part Sect. Ref. Size mm Quantity Item No. Part Sect. Ref. Size mm Quantity 1001 15 M6 x 12 86x 97x 108x 1067 6 295 16 M6 9 10 113x 1301 7 30 9x 1 13x 5 7 3.5 x
More informationSetup Guide. Read me BefoRe unpacking!
Setup Guide Read me BefoRe unpacking! Package Contents In The Replicator package The Replicator SD card (in The Replicator SD card slot) In the Accessory Box found within The Replicator frame Single or
More informationHardware installation
Hardware installation 5. Place and fix the OMT to the interface without tightening the screws. Figure 291: Place and fix the OMT to the interface Note: Take care to place the OMT with the engraved ARROW
More informationFIST-GCOG2-Dx6. Follow all local safety regulations related to optical fiber plant elements.
FIST-GCOG2 I N S T A L L A T I O N I N S T R U C T I O N TC-986-IP Rev A, Mar 2017 www.commscope.com FIST-GCOG2-Dx6 Content 1 Introduction 2 General 2.1 Abbreviations 2.2 Kit contents 2.3 Tools 2.4 Accessories
More informationWINEGARD TRAV LER Automatic Multi-Satellite TV Antenna
WINEGARD TRAV LER Automatic Multi-Satellite TV Antenna Model SK-7002 MANUAL STA R CHOICE A SHAW Company 1 888 554-STAR SK-7002 Winegard Company 3000 Kirkwood St. Burlington, IA 52601-2000 319/754-0600
More information2179-CD Series Fiber Optic Splice Closure. Installation Instructions
2179-CD Series Fiber Optic Splice Closure Installation Instructions 1.0 Product Introduction The new 3M TM 2179-CD Series Fiber Optic Splice Closure can be used in buried, underground, aerial, and pedestal
More informationWINEGARD INSTALLATION MANUAL. Model GM Carryout Ladder Mount for mounting pipes with outer diameters between 1 to 1-1/8
WINEGARD INSTALLATION MANUAL Model GM-3000 Carryout Ladder Mount for mounting pipes with outer diameters between 1 to 1-1/8 WARNING: DO NOT USE THE LADDER MOUNT AS A STEP! NOT INTENDED FOR USE WITH THE
More informationFixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v August 2009
Fixed Audio Output for the K2 Don Wilhelm (W3FPR) & Tom Hammond (NØSS) v. 2.1 06 August 2009 I have had several requests to provide a fixed audio output from the K2. After looking at the circuits that
More informationTable 4-1: Rating Levels
OBJECTIVES 1. Describe various level ratings that apply to telecommunication cables and jacks and identify where each is implemented. 2. Describe the various levels of the cabling category rating systems.
More informationMODEL... MXL012/55NZ MXL012/65NZ SIMPLICITY AT IT S BEST SET UP & USER MANUAL REGISTERED COMMUNITY DESIGN NO
SIMPLICITY AT IT S BEST MODEL... MXL012/55NZ MXL012/65NZ SET UP & USER MANUAL REGISTERED COMMUNITY DESIGN NO.2207746. PATENT PENDING SIMPLICITY AT IT S BEST THANK YOU! For purchasing this product, we trust
More informationBTT rev. a Bob s TechTalk #8
BTT rev. a Bob s TechTalk #8 Bob s TechTalk #8 by Bob Eckweiler, AF6C Coaxial Connectors: (Part I of III) UHF and N Connectors and MMCX/MCX Series. There are many other connectors that are less common
More informationCONSTRUCTION SPECIFICATION FOR TRAFFIC SIGNAL EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 620 APRIL 2017 CONSTRUCTION SPECIFICATION FOR TRAFFIC SIGNAL EQUIPMENT TABLE OF CONTENTS 620.01 SCOPE 620.02 REFERENCES 620.03 DEFINITIONS 620.04
More informationTVP-20 / RVP-412 CCTV VIDEO-PLEXER
TVP-20 / RVP-412 CCTV VIDEO-PLEXER INSTRUCTION BOOK IB640701 4-1-2003 TABLE OF CONTENTS DESCRIPTION 3 MOUNTING INSTRUCTIONS 3 RVP-412 MOUNTING INSTRUCTIONS 3-4 HOW TO CABLE THE TVP-20 5 HOW TO CABLE THE
More information27mm ECAM Double Cable Entry Port
27mm ECAM Double Cable Entry Port Instructions October 2006 1.0 Introduction The 3M 27mm ECAM Double Cable (External Cable Assembly Module) Entry Port is designed to accept fiber optic loose tube & central
More informationElectric Wall/Ceiling Projection Screen Saker Tab-Tension Series User s Guide
Electric Wall/Ceiling Projection Screen Saker Tab-Tension Series User s Guide Important Safety & Warning Precautions Make sure to read this user s guide and follow the procedures below. Caution: The screen
More informationSATELLITE DISH ANTENNA
SATELLITE DISH ANTENNA SELF-INSTALLER S GUIDE Safety Information DANGER! Avoid Powerlines! When following the instructions in this guide to install and connect the satellite antenna and connections, take
More informationInteractive Satellite Terminal Installation / Validation Manual
Installation / Validation Manual Version October 5, 2016 Index INTERACTIVE SATELLITE TERMINAL 1. FCC COMPLIANCE... 3 2. TECHNICAL FEATURES...4 3. GENERAL DESCRIPTION...5 4. ELEMENTS CONTAINED IN THE TERMINAL...6
More information