र य गक स थ न प द र न ह नगर, क र ल 609 605 NATIONAL INSTITUTE OF TECHNOLOGY PUDUCHERRY Nehru Nagar, Karaikal 609 605 NIQ No.: NITPY / 015-16/ECE/ DE & CE LAB / Q00 Date: 05-0-016 NOTICE INVITING QUOTATION Procurement of IC TESTER & TRAINER KITS, OSCILLOSCOPES, FG S, DECADE BOXES AND ANALOG METERS National Institute of Technology Puducherry invites separate sealed quotations from the reputed vendors for supply of the following items: Sl. No Equipment name Required quantity 1 Digital IC Trainer Kit Digital IC Tester 1 IC Tester 1 Cathode Ray Oscilloscope 5 Function Generator 6 Decade Resistance box 7 Decade Inductance box 8 Decade Capacitance box 9 voltmeter 10 9 16 The complete details of specification and the items to be supplied is given in Annexure I. Eligibility conditions and method of submission of bidding documents, etc. are given in Terms and Condition. Last Date & Time: Submission of Quotation: 8-0-016 up to 0:00 pm Opening of Quotation in the presence of available bidders: 8-0-016 at 0:0 pm Sd/- Registrar (i/c)
र य गक स थ न प द र न ह नगर, क र ल 609 605 NATIONAL INSTITUTE OF TECHNOLOGY PUDUCHERRY Nehru Nagar, Karaikal 609 605 Terms & Conditions 1. Separate sealed quotations are invited for Supply of IC TESTER & TRAINER KITS, OSCILLOSCOPES, FG S, DECADE BOXES AND ANALOG METERS as per the details given in the Annexure I:. The sealed quotations should reach The Registrar, National Institute of Technology Puducherry, II Floor, PKEC Campus, Nehru Nagar, Karaikal - 609605 on or before 8-0-016 up to 0:00 pm and they will be opened on the same day at :0 PM in the presence of available bidders. The offers will not be considered if received after the bid closing date and time.. The quotations should be sealed and superscripted as Quotation for supply of IC TESTER & TRAINER KITS, OSCILLOSCOPES, FG S, DECADE BOXES AND ANALOG METERS. The rates should be inclusive of all taxes, freight, packing, forwarding, etc. 5. The rate quoted shall on FOR destination basis at our premises. 6. The firm should have been in existence for at least last three years (proof to be attached) 7. The quote is not transferable. 8. The offers received through telex / tele-fax / e-mail will not be accepted by the Institute under any circumstances. 9. The Institute shall not be responsible for any delay / loss or non-receipt of quotes by post / courier service. 10. No unsolicited correspondence shall be entertained after the submission of the offer. 11. Quoting merely the lowest price does not confer any right to any bidder for award of supply order. The Institute reserves the right to select any bid on the grounds of quality, offer of additional / special features, compatibility, etc. 1. The Institute also reserves the right to reject any bids with sub-standard products even if they are found to be lowest. 1. The period of delivery exceeding three months is not normally allowed. 1. Full particulars regarding the make, manufacturing specifications and standards, guarantee period, and descriptive literature should accompany the quotation. 15. The price and the delivery period should be clearly stated in the quotation. 16. If any articles are not up to the prescribed quality or specification it is liable for outright rejection.
17. At the time of dispatch of articles, Delivery Note should be given along with the articles. 18. The list of Items is attached as Annexure I The firms may quote any single items or whole items separately as the case may be. 19. Failure to supply the item indented within delivery time will result in automatic cancellation of Supply Orders. Such automatic cancellation empowers the Institute to purchase the items from other available sources and to recover the difference between the prices so paid and those payable under the contract. Also failure to comply with the general spirit of the contract will lead to termination of contract and effecting purchases required from outside sources and to recover the loss in such kind of purchase from supplier. 0. In case of failure to supply within the time specified in the Purchase order, a penalty/ld of 0.5% of the total value per week or a part thereof shall be levied subject to a maximum of 7.5% in respect of items which are not supplied. The decision of National Institute of Technology Puducherry shall be final in this regard. Date: 05-0-016 -Sd/- Registrar (i/c) Accepted the terms & Conditions Name, Sign & seal of the vendor
ANNEXURE I Procurement of IC TESTER & TRAINER KITS, OSCILLOSCOPES, FG S, DECADE BOXES AND ANALOG METERS NITPY s Specifications Sl. No Equipment name Specification Required quantity 1 Digital IC Trainer Kit Power Supply Special Supplies +5V/1A,±1V/500mA Ripple Less than 1mV Regulation Less than 0.1% Protection Protection against Load and short circuit BCD to Segments Seven Segment Decoder TTL 1Hz to 1MHz Clocks Indication LED of output Mono High & Low pulse IC Sockets Four 16 Pin ZIF Sockets Physical Parameters Accessories Logic I/P and O/P Weight Bread Board Fuse Manual Patch cords One 8 Pin Socket 1 No s Less than 8 Kg One attached the trainer kit 1A No s One set 0 No s(each one kit) Digital IC Tester Test Range TTL 7/5 TTL 7/5 CMOS 0/5DRIVExxx/ VLSI, Interface, Memory, User Test Time Average Search Time less than 5sec Display LCD/LED display Power source 0V 50Hz supply & Provision for battery (in case of power failure) Weight Less than 5 Kg 1
IC Tester Cathode Ray Oscilloscope 5 Function Generator Test Range Op-amps, Comparators, Regulators, Opto-isolators, switches / Multiplexers, Transistor arrays, Timer ICs Test Time Average Search Time less than 5 sec Display LCD/LED display Power 0V 50Hz supply & Provision for battery (in case of source power failure) Weight Less than 5 Kg High luminance, light and handy, reliable. Fully sealed long live vertical mode switch. Triggering Level Lock Function, Automatic Synchronize Function, 10 times sweep magnification. Technical specifications Accessories Type Operating Modes. Vertical deflection (Y) Horizontal deflection (X) Time Base Test Frequency Sensitivity Power Supply Manual Connecting probes 0MHz Dual Channel. Channel I, channel II, Channel I and II Alternate or chopped, X-Y Operation Band with; 0Mhz, Band with;.5mhz, 5mv to 0V 0.5us/cm-0.s,magnifier; X10(+-5%). 50 Hz, Continuity test beep sound 1m V/DIV. 0VAC, Power :6.5VA One set 0 o s(each one kit) Wave forms: Sine, Triangular, Square, Ramp, TTL An CMOS, External Voltage Controlled frequency Function, Duty Cycle Control with signal Inversion Capability, Two- Step (-0 db X ) and variable attenuator. 1 Range Output Amplitude 0.Hz to MHz in 7 Decade ranges 0-0V PP 6 Decade Resistance box Technical specifications Accessories Frequency Read Out Frequency variation Amplitude variation Offset Protection Maximum frequency resolution Display Power supply Manual Connecting probes Digital frequency counter (LCD display) Fine control 0-0V PP Coarse variation control ±DC offset variable control Output protected against short circuit 100 MHz 6 Digit LED 0V, 50HZ,AC One set 0 o s(each one kit) 6 Dials Dial 1). 10 10 decades = 100 Dial ). 100 10 decades = 1K Dial ). 1K 10 decades = 10K Dial ). 10K 10 decades = 100K Dial 5). 100K 10 decades = 1M Dial 6). 1M 10 decades = 10M Technical specifications Number of Dials 10 to 10
7 Decade Inductance box Technical specifications M - 6 Dials Power W Accuracy ± % 5 Dials Dial 1) 10 H 10 decades = 100 H Dial ) 100 H 10 decades = 1mH Dial ) 1mH 10 decades = 10mH Dial ) 10mH 10 decades = 100mH Dial 5) 100mH 10 decades = 1H Number of Dials 10 µh to 1 H 5 Dials Voltage 50V (Max) Accuracy ± % 8 9 Decade Capacitance box Technical specifications 5 Dials Dial 1) 100pf 10 decades = 1nf Dial ) 1nf 10 decades = 10nf Dial ) 10nf 10 decades = 100nf Dial ) 100nf 10 decades = 1 f Dial 5) 1 f 10 decades = 10 f Number of Dials 100 pf to 10MFD 5 Dials Voltage 50V (Max) Accuracy ± % (0-5V) voltmeter TOLERANCE % 10 (0-0V) voltmeter TOLERANCE % 11 ( (0-0V) voltmeter TOLERANCE % 1 (0-0 ma)
TOLERANCE % 1 (0-00 ma) TOLERANCE % 1 (0-00μA) TOLERANCE % 15 (0-10mA) TOLERANCE % Date:05-0-016 -Sd/- Registrar ( i/c)