C98 series Compact, easytouse driver circuit The C98 series CMOS driver circuit is designed for photodiode arrays with amplifier. The C98 series operates a linear image sensor by just inputting two signals (MCLK and MRESET) and a signal 5 V supply. The C98 series is assembled on a compact board measuring 48 56 mm and allows downsizing of the measurement equipment. The C98 is intended for single use or parallel connections, while the C980 is suitable for cascade connections. Features Single power supply (5 V) operation Operation with two input signals (MCLK and MRESET) Compact: 48 56 5. t mm Applications Various types of image acquisition Optical detection equipment Compatible photodiode arrays with amplifier Driver circuit amplifier (sold separatery) for photodiode array Element size with amplifier Type no. Number of elements (pitch height) S86564, S86564G 64 0.8 mm 0.8 mm C98 S8658, S8658G 8 0.4 mm 0.6 mm C980 S86680, S8668G0 8 0.8 mm 0.8 mm S866640, S86664G0 64.6 mm.6 mm Note: These circuits do not support the S886556, S8866640, S86556 and S86556G. Absolute maximum ratings Parameter Symbol Condition Value Unit Supply voltage Vcc Ta=5 C 7 V Digital input voltage Ta=5 C V V Operating temperature Topr 0 to 50* C Storage temperature Tstg 0 to 70* C *: No condensation Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Specifications (Ta=5 C) Parameter Symbol Min. Typ. Max. Unit Rated voltage 4.9 5.0 5. V Current consumption Is 75 80 ma Digital input High level VIH.0 5 V Low level VIL 0 0.8 V MRESET pulse width (Low level) TpwstRESET 0 μs MCLK frequency f(clk) 40 4000 khz Digital rise/fall times ttlh/tthl 0 30 ns Data rate fv 0 000 khz Offset output Voffset 0.5 V saturation output* Vsat 4.5 V *: From offset value www.hamamatsu.com
C98 series Block diagram (C980) array with amplifier CN CLK RESET Trig EOS EXTSP Vms Vg Vdd Video Vref Vp Vp SW Controller Vp VR SW : TOP : END REF MCLK MRESET INSTART GAIN 5 V MCLK MRESET EXTSP GAIN 5 V The C98 does not have. KACCC087EH Timing chart Timing chart of first stage sensor when used singly or in cascade connection MCLK MRESET 3 4 5 6 7 8 9 0 Last stage sensor signal is output when used in cascade connection. Timing chart of second and subsequent stage sensors when used in cascade connection MCLK MRESET INSTART signal is output right after EXTSP signal input from previous stage Last stage sensor signal is output when used in cascade connection KACCC088EA
C98 series Connection examples Single or parallel readout example (C98) Simultaneous integration/output (effective for highspeed processing) amplifier C98 input/output cable (accessory) amplifier C98 amplifier C98 KACCC089EE Cascade readout example (C980) Simultaneous integration/serial output (Simplifies external processing circuit) amplifier C980 input/output cable (accessory) amplifier C980 Cascade connection cable (accessory) amplifier C980 KACCC090EF 3
C98 series Dimensional outlines (unit: mm) amplifier (sold separately) 5 C98 Driver circuit for photodiode with amplifier C98 56 3 38 4 ( ) R. 0 5. CN 8 3 8 C980 amplifier (sold separately) 5 Driver circuit for photodiode with amplifier C980 56 3 38 4 ( ) R. 0 5. CN 48 6 8 3 8.6 3.6.6 3.6 48 6 4 * S86564, S86564G, S8658, S8658G KACCA0357EB 4 * S86564, S86564G, S8658, S8658G KACCA04EE 4
C98 series Pin assignment of I/O connector CN [Connector type: 808700000 PRECIDIP (made by DURTAL) or equivalent] Pin no. Terminal Name I/O Description RESET O Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. CLK O Sensor scan sync signal. Sensor starts scanning in synchronization with this signal. 3 Trig I For A/D conversion timing signals. Positive logic 4 EXTST O High level at first stage during parallel or serial readout. At second and subsequent stages during serial readout, this outputs the EOS pulse of preceding stage. 5 Vms O High level at first stage during parallel or serial readout. At second and subsequent stages, this sets to Low level. 6 Vdd O Sensor supply voltage 7 Sensor 8 EOS I EOS (end of scan) signal of sensor. Negative logic 9 Video I Video output signal. Positive polarity 0 Vref O Reference voltage Vgain O Sensor gain switching H: high gain, L: low gain Vpd O voltage [Connector type: DF30P.5H (50) (made by Hirose Electric)] Used to connect the first stage to an external I/O during parallel readout or serial readout For the second and subsequent stages during serial readout, is used to connect to at preceding stage. Pin no. Terminal Name I/O Description MRESET I Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. MCLK I Sensor scan sync signal. Sensor and circuit start operating in synchronization with this signal. 3 O For A/D conversion timing signals. Positive logic 4 O EOS (end of scan) signal of all sensors during parallel or serial readout. Negative logic 5 INSTART I NC (no connection) at first stage during parallel or serial readout. At second and subsequent stages during serial readout, this receives the EOS pulse of preceding stage. 6 GAIN I setting for sensor gain H: high gain, L: low gain 7 Circuit 8 5 V I 5 V power supply 9 O Video output signal. Positive polarity 0 A. O Video [ is installed only for C980. Connector type: DF3P.5H (50) (made by Hirose Electric)] Used to connect to at next stage during serial readout. Pin no. Terminal Name I/O Description MRESET I Sensor scan start signal. Pulse width at High level nearly equals sensor integration time. MCLK I Sensor scan sync signal. Sensor starts scanning in synchronization with this signal. 3 O For A/D conversion timing signals. Positive logic 4 O EOS (end of scan) signal of all sensors during parallel or serial readout. Negative logic 5 EXTSP O Video signal scan start signal at second stage during serial readout. Negative logic 6 GAIN I setting for sensor gain H: high gain, L: low gain 7 Circuit 8 5 V I 5 V power supply 9 O Video output signal. Positive polarity 0 A. O Video NC No connection NC No connection Note: is installed only for serial readout. Pin no. to 4 and 6 to 0 connect to the same pin No. of as common lines. 5
C98 series Parallel readout and serial readout settings (C980) <Parallel readout setting> 3 4 Set SW and SW to OFF as shown at left. <First stage setting for serial readout> 3 4 Set SW to OFF and SW to as shown at left. <Second stage to second from last stage setting for serial readout> 3 4 Set SW and SW to as shown at left. <Last stage setting for serial readout> 3 4 Set SW to and SW to OFF as shown at left. KACCC09EA 6
C98 series Accessory (unit: mm) C98 input/output cable C980 input/output cable Cascade connection cable input/output cable This cable connects to an external device (power supply, pulse generator, etc.). Connector: DF30S.5C (made by Hirose Electric) Terminal: DF3630SCFA (gold plating) Cable: Conforms to UL06 AWG8 Cascade connection cable This cable connects between and for serial readout. Connector: [] DF30S.5C (made by Hirose Electric) [] DF3S.5C (made by Hirose Electric) Terminal: DF3630SCFA (gold plating) Cable: Conforms to UL06 AWG8 [] [] [] 00 00 KACCC098EB KACCC0773EA Pin no. Color Pin no. Color Brown 6 Blue Red 7 Purple 3 Orange 8 Gray 4 Yellow 9 White 5 Green 0 Black Pin no. Color Pin no. Color Brown 7 Purple Red 8 Gray 3 Orange 9 White 4 Yellow 0 Black 5 Green No cable 6 Blue No cable Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions Disclaimer Information described in this material is current as of April 07. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTICS K.K., Solid State Division 6 Ichinocho, Higashiku, Hamamatsu City, 4358558 Japan, Telephone: (8) 5343433, Fax: (8) 53434584 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: () 90830960, Fax: () 90838 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 0, D8 Herrsching am Ammersee, Germany, Telephone: (49) 853750, Fax: (49) 85658 France: Hamamatsu Photonics France S.A.R.L.: 9, Rue du Saule Trapu, Parc du Moulin de Massy, 988 Massy Cedex, France, Telephone: 33() 69 53 7 00, Fax: 33() 69 53 7 0 United Kingdom: Hamamatsu Photonics UK Limited: Howard Court, 0 Tewin Road, Welwyn Garden City, Hertfordshire AL7 BW, United Kingdom, Telephone: (44) 70794888, Fax: (44) 70735777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 6440 Kista, Sweden, Telephone: (46) 85090300, Fax: (46) 8509030 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, int. 6, 000 Arese (Milano), Italy, Telephone: (39) 09358733, Fax: (39) 0935874 China: Hamamatsu Photonics (China) Co., Ltd.: B0, Jiaming Center, No.7 Dongsanhuan Beilu, Chaoyang District, Beijing 0000, China, Telephone: (86) 065866006, Fax: (86) 06586866 Cat. No. KACC087E3 Apr. 07 DN 7