CONTROL VISIO ASSISTANCE Our qualified technicians are at your disposal for: Electronics signals of medical gas networks by VISIO concept, (ISO 7396 norm) is the solution to prevent any defaults of medical gas networks. This system gives precise information about the gas pressure, together with a secure traceability of the failures. The analogical technology of the sensors allows a great precision and a good stability. - Optimizing the different network configurations - Helping you with installation and programming - Finding any eventual connecting default - Training your technicians on system. Full free service (excluding external expenses in case) Direct line 0033 (0)3 28 16 04 88 ACCESSORIES Waterproof analogical sensors provided with a cable of connecting and streamlined oxygen. Brass adapters for sensors mounting on the relaxation units and the pipes. Pressure sensor 0-16 atm ( G 1/4 ) VAL 303 Depression vacuum compact sensor 0-0.9 atm ( M 10 ) VAL 304 2 Pressure sensor 0-250 atm ( G 1/4 ) VAL 0302 3 Mounting valve system for G 1/4 ( 250 atm only ) VAL 0401 Reducer for compact sensors VAL 1201 VAL 303 VAL 304 VAL 0302 VAL 0202 VAL 1201 VAL 0401 Mounting box for compact sensors VAL 0202 caracteristics VISIO 5 VISIO 100 Logic way input 5 4 x 5 Analogic ways (sensors) 5 7 Emergency Battery 1H00 - Quantity of remote unit 0 20 max Recording Data processing 99 latest events Pre alarm No Yes Reset 15 min to 7 days 0 to 16 min Buzzer 1 Adjustable Languages 3 2 Networks pressures display Sequence Permanent Supply cuttingand error delays Yes Yes Type of default Logic pression Logic pression Sensors 4-20mA 4-20mA Programming On board On board or global system control Serie link RS 232 - RS 485 RS 232 - RS 485 Link GBS 1 synthesis + 5 direct links 1 synthesis + 4 dedicats Size - weight 166x160x133 mm - 1,8 kg 251x250x76 mm - 2 kg Box Waterproof Wall Mounted / Integrated Box SUPERVISION The VISIOSOFT System is a powerful control software. Up to 27 alarms units, it allows to remote parameters of each alarm unit, centralization of the defaults on the same printer and analyses problem at distance. The alarm units are together connected and to the computer by BUS 485. The VISIOTEL interface dispatches the information by telephone for hospitals which are distant. WALL UNIT INTEGRATION Wall integration VISIO 100 version allows a discreet integration of alarm system into a column or a depressurization box in the operating theatre or in the emergency units. Column Emergency units Wall mounting
VISIO 5 ALARM UNIT Visio alarm unit manages 5 analogical or logic inputs. The concerned gas pressures are on liquid crystal display. Several green and red leds confirms the normal use or the default of concerned gas. By its polyvalence you can also either use it for gas production (bottle, compressors) or inside hospital network control. VISIO 5 alarm unit, wall mounted box VAL 0001 VISIO 5 alarm unit, wall integrated box VAL 0010 VISIO 5 Battery VAL 0002 6 INSTALLATION AND MAINTENANCE Unibloc Alarm VISIO 5 with possible connection by bottom or rear. Release connectors of different sizes for avoiding any confusion. Supply power feeding 230 V 1,5 mm2 cable. All other wiring (sensors and reports) are in 2even cables SYT type with screen. Pre-programmed unit for a 4 secondary gas network. FUNCTIONALITIES Alarm led (red color); operation (green color) Gas identifications 5 logical/analogical ways. Supply power Battery default Led alarm Led transmission Buttons for parameters Buttons for concellation Test button for leds and display
Biolume Installation Directions 1 / 13 INSTALLATION DIRECTIONS VISIO5 Parc EURASANTE 310 rue Jules Valles 59120 LOOS - France +33 328.16. 04. 80 - fax +33 328.16. 04. 89 website www.biolume.com
Biolume Installation Directions 2 / 13 TABLE OF CONTENTS TABLE OF CONTENTS...2 USE AND DISPLAY...3 BATTERIES...4 DRILLING SIZE...5 ELECTRICAL CONNECTIONS...6 PARAMETERS...7 LIST OF DATA...11
Biolume Installation Directions 3 / 13 USE AND DISPLAY When connected, the unit displays the date of program version. VISIO 5 250701 Then, the unit successively displays the status of the different monitored medical gases. OXYGEN 4.0 b NITROUS 3.0 b AIR -500 m Above example can be different according to the input central alarm unit program. In case of default, the concerned medical gases are successively displayed and blink then NITROUS B 1.8 b OXYGEN H 6.3 b When the pressure is too low, B blinks. When the pressure is too high, H blinks. Simultaneously when default appears, the red led DEFAULT blinks so does the red led of gas display. The buzzer is activated. CAUTION : With 250701 software, medical gas leds do not blink. For stopping the buzzer, the technician must press on desactivation button. Then the defaults leds light but do not blink. If a new default appears, the default led blinks and the buzzer is reactivated. If, after acknowledgement, the default disappears, the "ERROR" led lights go off. The display appears like in statement If the default is acknowledged (do not disappear after a pre-recorded period), the buzzer is reactivated and the red led "ERROR" blinks again (general default and medical gas default).
Biolume Installation Directions 4 / 13 BATTERIES The VISIO 5 unit is standard provided with batteries securing its use and also the sensors power feeding (for at least 1 hour in case power is cut off). Contrary to the VISIO 4 unit, no Shunt battery is necessary. For stopping the VISIO 5 unit, you must disconnect the power supply (230V), then you have to disconnect and reconnect the plug of the battery. In this case, the VISIO 5 type does not use any power. The units are offered with half-charged batteries. Please put the batteries on charge for 24 hours for a full charge. In case of total discharge, 48 hours are necessary. We recommend to replace the batteries every 2 years (EC medical).
Biolume Installation Directions 5 / 13 DRILLING SIZE
Biolume Installation Directions 6 / 13 ELECTRICAL CONNECTIONS C22 L1 C23 C32 C21 Z5 R35 D10 Z6 C27 D12 C30 IC D13 P2 L2 L3 D14 C28 D15 R32 R33 R34 R38 R39 IC10 D11 C26 D16 C25 D17 L4 FU8 FU5 BIOL04A-C T4 T5 T6 T7 T8 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R50 R51 R52 R53 R54 T9 T10 T11 T12 T13 C34 J4 R58 R59 R60 R61 R62 C31 FU4 T0A1 D18 FU1 T0A1 FU2 K5 L N T0A1 K3 RL1 K4 NO NF C ALARME RL2 RL3 RL4 RL5 RL6 K6 K7 K2 NO1 NF1 NO2 NF2 NO3 NF3 C1 NO4 NF4 NO5 NF5 C2 V+ A B 0V GTC1 GTC2 GTC3 GTC4 GTC5 RS485 EN5 VC5 EN4 VC4 EN3 D19 VC3 R65 EN2 R66 D20 VC2 R67 EN1 R68 D21 VC1 R69 R70 K1 D22 R71 R72 D23 R73 R74 FU11 F1A BIOLUME BIOL04A-F K5 Connector Power supply 230V : plug the (+) on "L", the neutral on "N" and connect to the earth. K4 Connector Switches for the connection of the GBC switch-relay. From left to right, the contacts are "neutral", "use" and "common". In case of alarm (or low battery level), the contacts "common" and "use" shut. K6 & K7 Connectors Switches for the connection of the GBC switch-relay. From left to right, the contacts are "neutral" and "use". The common of the channels 1, 2 and 3 has to be connected to C1. The common of the channels 4 and 5 has to be connected to C2. In case of alarm (or low battery level), the contacts "common" and "use" shut. K1 Connector Connectors switches sensors. 5 free available channels : from EN1 to EN5. These channels can be used either analogical or logical channel according to the programming of the VISIO 5. Feeding of sensors by VC1 to VC5). CAUTION : These signals are not connected together. You must link the sensor to the same source EN and VC.
Biolume Installation Directions 7 / 13 PARAMETERS This chapter contains all information which will allow you to read, check and program and to adapt the use of the unit for a specific configuration in which it is installed. The parameters can be modified according to your requirements via the LCD display and the four buttons M, C, D and U. When the VISO 5 type is power supplied, pressing on one of the buttons switches on the display during 5 seconds. The parameters are recorded in an EEPROM memory (or E2PROM type), which keeps the information even when the VISIO 5 is totally out of supply. Every parameter is identified by an abbreviated name and a line (hexadecimal basis (with figures : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F), corresponding with the position where it is recorded into the EEPROM memory. The display indicates for every parameter, its address, its abbreviated name and its value. 00C TP1 0015 mn Access to the different lines of the notice Accessible lines from 006 to 025 for the access of parameters. The 000 address is the main display for the pressures or the defaults (previous chapter). (The 000 address is not displayed but is implicit). The address is automatically forced to 000 when the 4 buttons of parameters are not activated during one minute. This can be also done by pressing simultaneously on CLEAR buttons. The addresses from 001 to 005 allow to permanently display the medical gas pressures which are connected to input from 1 to 5 : 001 OXYGEN 2.6 b 002 NITROUS 4.3 b 003 AIR 12.5 b 004 VACUUM -400 m Only the first five letters of the name of medical gas are displayed. If an input is configured as a logical input, the pressure value is replaced by OK or DEFAULT : 005 CHANNEL5 OK 005 CHANNEL5 DEFAULT
Biolume Installation Directions 8 / 13 EXAMPLE : Set the display to the 000 address by pressing simultaneously on CLEAR buttons. (the address 000 is not displayed, it is implicit recorded) OXYGENE 5.1b Each press on U button adds 1 to the address. Each press on D button adds 10 to the address. A simultaneous pressing on C et D buttons resets the address to 000. 001 OXYGEN 5.1 b 011 TP2 015 mn 001 OXYGEN 5.1 b The address 000 is automatically forced to 000 when the 4 buttons of parameters are not activated during one minute. This can be also done by pressing simultaneously on CLEAR buttons. How to change the program No possible modification of parameter if supply feeding of the alarm is switch off. Numerical program Each press on U button, increases by 1 the indicated value. Each press on D button, increases by 10 the indicated value. Each press on C button, increases by 100 the indicated value. Each press on M button, increases by 1000 the indicated value. Reset the address to 000 and press once on D button, then 3 times on U button in order to choose the address 13 Press on MODIF buttons. simultaneously Press on M, C, D, U buttons to change the value of this specified time. MDF TP3 0010 mn MDF TP3 1255 mn 1x 2x 4x 5x
Biolume Installation Directions 9 / 13 Record the new parameter by pressing the VALID button simultaneously. If the value of the parameter is not correct, it is automatically modified. 016 TP3 1255 mn Or cancel the modification by pressing again on the MODIF buttons simultaneously 016 TP3 0010 mn By pressing on CLEAR buttons simultaneously, the program value is reset to 000 : MDF TP3 0010 mn MDF TP3 0000 mn Choice from a list : The U button allows to change the choice from a list : 009 CAP1 0/16b MDF CAP1 0/16b MDF CAP1 0/250b MDF CAP1 N.C. MDF CAP1 0/-0.9b 009 CAP1 0/-0.9b
Biolume Installation Directions 10 / 13 Choice of language Two possibilities are offered to speak your language. They appear at the address 006 under the title : FRANCE, ENGLAND, DENMARK,... Press 6 times on D button in order to select the 006 address. Press on MODIF buttons simultaneously Press on U button and choose the required language 006 COUNTRY FRANCE MDF COUNTRY FRANCE MDF COUNTRY Record the required language of the unit by pressing on VALID buttons simultaneously. 006 PAYS ENGL In above example, the used language will be English.
Biolume Installation Directions 11 / 13 LIST OF DATA 006 COUNTRY FRANCE DENMARK FRANCE Shows the used language for the menus. The values can be chosen between France, English, Denmark and so on... 007 CODE 0000 9999 1234 This parameter allows to protect the parameters owing to a code. If the exposed value is zero, the modification of the parameters is not allowed. If the exposed value is not zero, the modification of the parameters is allowed. To change the parameters : register the code and enter. If the registered code is not correct, the value 0000 is exposed. To forbid the modification of the parameters, register the code 0000. To change the code, register the old code, enter, register the new code and enter. CAUTION : This function is not available for the 250701 version of the software. 008 ENT1 OXYGEN CHANNEL4 OXYGEN Type of medical gas controlled by sensor n 1. It can be chosen in the following list : OXYGEN, NITROUS, AIR, VACUUM. 009 CAP1 N.C. 0/250b 0/16b Type of sensor connected to input n 1, it can be chosen in the following list : NC (not connected = input not used), 0/16b, 0/250b, 0/0.9b, Digital (logical input : "TOR"), means that input is all or nothing. Contrary to VISIO 4, the selection digital / analogic input is automatic. 00A MINI1 5% of sensor 95% of sensor 03.3 Pressure value under which the default is detected for input n 1. The default appears if the pressure is strictly lower than the MINI 1 value 5%. If the value of the parameter is lower or higher than the sensor scale, it is automatically modified. In the case of a digital sensor, the values are in percent.
Biolume Installation Directions 12 / 13 00B MAXI1 5% of sensor 95% of sensor 05.9 Pressure value 1 above which the default is detected for input n 1. The notes concerning the MINI1 parameter also applies to this parameter. MAXI1 must always be higher than MINI1. If not, MAXI1 is automatically equal to MINI1. Caution : If CAP1 = 0/0.9b For a negative pressure sensor, the absolute value of MAXI1 must be higher than the absolute value of MINI1. For example : if pressure must remain between -600 mb and -100mb : you must consider the parameter -600 for the value MAXI1 and -100 for MINI1. 00C TP1 5 mn 9999 mn 15 min After the above mentioned periods (in minutes), the buzzer is activated if the default does not disappear after validation. The maximum value of the period is 9999/60=166h (7 days) Here are a few useful values : Expected TP1 time ¼ hour 15 ½ hour 30 1 hour 60 2 hours 120 3 hours 180 4 hours 240 6 hours 360 12 hours 720 24 hours 1440 36 hours 2160 2 days 2880 3 days 4320 4 days 5760 5 days 7200 6 days 8640
Biolume Installation Directions 13 / 13 The following addresses repeat the 00D to 020 parameters only for 2,3, 4 and 5 inputs. 00D ENT2 OXYGEN CHANNEL4 NITROUS 01E CAP2 N.C. 0/250b 0/16b 00F MINI2 0 100 % de CAP2 02.6 010 MAXI2 0 100 % de CAP2 04.7 011 TP2 5 mn 9999 mn 15 mn 012 ENT3 OXYGEN CHANNEL4 AIR 013 CAP3 N.C. 0/250b 0/16b 014 MINI3 0 100 % de CAP3 03.0 015 MAXI3 0 100 % de CAP3 05.3 016 TP3 5 mn 9999 mn 15 mn 017 ENT4 OXYGEN CHANNEL4 VACUUM 018 CAP4 N.C. 0/250b 0/-0.9b 019 MINI4 0 100 % de CAP3-370 m 01A MAXI4 0 100 % de CAP3-854 m 01B TP4 5 mn 9999 mn 15 mn 01C ENT5 OXYGEN CHANNEL4 CHANNEL5 01D CAP5 N.C. 0/250b Digital 01E MINI5 0 100 % de CAP3 000 % 01F MAXI5 0 100 % de CAP3 050 % 020 TP5 5 mn 9999 mn 15 mn Reserved for a future use : 021 TX1 CHANNEL1 022 TX2 CHANNEL2 023 TX3 CHANNEL3 024 TX4 CHANNEL4 025 TX5 CHANNEL5 These parameters gather the extra program medical gases which are added to the data OXYGEN, NITROUS, AIR, VACUUM. Eight characters are available for each text. In modification mode, the U touch allows to change the letter on the cursor. The authorised characters that can be integrated are : space, 0 to 9 and A to Z. The D key allows to move the cursor.