Technical Data Sheet 3 Scotchlite Reflective Material Series 6100 High Gloss Trim Series 6200 High Gloss Film Technical Data Sheet August 1999 Description 3M Scotchlite Reflective Material - High Gloss is designed to enhance the visibility of the wearer, in daytime, nighttime, or low-light conditions. 3M Scotchlite Reflective Material - Series 6200 High Gloss Film consists of highly retroreflective microprisms formed on flexible, glossy, and UV-stabilized polymeric film. A white flexible film sealed on the backside of the 3M Scotchlite Reflective Material - Series 6100 High Gloss Trim encapsulates the microprisms and protects the reflective product from dirt and moisture penetration. Fluorescent red-orange and fluorescent lime-yellow high gloss colors are conspicuous under daytime conditions, particularly at dawn or dusk. Color Product Number Daytime Color Reflected Color 6160 or 6260 White White 6183 or 6283 Orange Orange 6184 or 6284 Green Green 6185 or 6285 Blue Blue 6186 or 6286 Fluorescent Red red-orange 6187 or 6287 Fluorescent Yellow lime-yellow 6188 or 6288 Yellow Yellow 6189 or 6289 Red Red Retroreflective Performance The coefficient of retroreflection (R A, in cd/lux/m 2 ) is measured by methods traceable to either of the following retroreflective intensity testing procedures: ASTM E809 and E810 (R A ) CIE 54: 1982 (R ) The R A values were measured at the listed specific entrance and observation angles. The R A values are averages of readings taken from orientation angles that are 90 degrees apart unless stated differently. The 0 orientation angle is to be taken as downweb of 3M supplied rolls. Please contact your 3M representative for the proposed specifications. Product Daytime Entrance Observation Typical Minimum Number Color Angle Angle R A R A 6160 or White -4.0 0.2 700 330 6260 5.0 0.33 500 250 40 0.2 200 65 6187 or Fluorescent -4.0 0.2 700 330 6287 lime-yellow 5.0 0.33 500 250 40 0.2 200 65 6183 or Orange -4.0 0.2 450 200 6283 5.0 0.33 250 110 40 0.2 125 50 6188 or Yellow -4.0 0.2 450 200 6288 5.0 0.33 250 110 40 0.2 125 50 6184 or Green -4.0 0.2 300 150 6284 6189 or Red -4.0 0.2 200 100 6289 6186 or Fluorescent -4.0 0.2 170 60 6286 red-orange 6185 or Blue -4.0 0.2 75 30 6285
EN 471 and ANSI Performance 3M Scotchlite Reflective Material - 6160 White High Gloss Trim, 3M Scotchlite Reflective Material - 6260 White High Gloss Film, 3M Scotchlite Reflective Material - 6187 Fluorescent lime-yellow High Gloss Trim, and 3M Scotchlite Reflective Material - 6287 Fluorescent lime-yellow High Gloss Film are certified to the European Standard EN 471 High-visibility warning clothing as class 2 separate performance retroreflective materials. These products will meet or exceed the American National Standard for High-Visibility Safety Apparel, ANSI/ISEA 107-1999 Level 2 retroreflective performance. The initial photometric performance meets or exceeds the requirements in EN 471 Table 5 and ANSI/ISEA 107-1999 Table 5. The products are EN 471 certified for 75 washings at 60 C. Material subjected to the exposure tests listed below will maintain a minimum R A of 100 cd/lux/m 2 at -5 entrance angle and 0.2 observation angle unless stated otherwise. Initial Retroreflectivity:... EN 471 Class 2 (Table 5) ANSI/ISEA 107-1999 Level 2 (Table 5) Abrasion:............. pren 530 Method 2 5000 cycles Flexing:............... ISO 7854 Method A 7500 cycles Cold Fold:............. ISO 4675 (-20 C) Temperature Cycle:...... 12 hours @ (50±5) C 20 hours @ (-30±2) C Wash:................ ISO 6330 Method 2A 75 cycles @ 60 C wash and tumble dry @ 50 C Wet Reflectivity:........ EN 471 Annex A Physical Performance 3M Scotchlite Reflective Material - Series 6100 High Gloss Trim and 3M Scotchlite Reflective Material - Series 6200 High Gloss Film are subjected to the exposure tests listed below and will maintain a minimum R A of 100 cd/lux/m 2 at 0 orientation, -4 entrance angle and 0.2 observation angle unless stated otherwise. Performance Approved Test Feature Products Method Cold Flex: Series 6100 and 6200 ISO 4675 (-15 C) No cracks over a 3mm mandrel Wash: Retains Series 6100 and 6200 ISO 6330 Method 2A >80% of (except white and 15 cycles @ 40 C wash initial R A fluorescent lime- and @ 38 C tumble dry yellow, see EN 471 performance) Heat Resistance: Series 6100 and 6200 82 C for 30 minutes >75% of (except white and initial R A fluorescent limeyellow, see EN 471 performance) Wet Reflectivity: White, orange, green, EN 471 Annex A fluorescent lime-yellow, yellow Solvent Series 6100 and 6200 Wiped with a soft cloth Resistance: containing mineral Will not dissolve spirits, kerosene, or pucker unleaded gasoline, methanol, or VM&P Naphtha Wash:................ ISO 6330 Method 2A R A > 330 50 cycles @ 60 C wash (Average of 0 /90 ) and tumble dry @ 50 C
Color Specifications The initial chromaticity coordinates for 3M Scotchlite Reflective Material - Series 6100 High Gloss Trim and 3M Scotchlite Reflective Material - Series 6200 High Gloss Film with a white backing, as measured in accordance with ASTM E1164-94, are within the color boxes defined below: 6160 & 6260 White x 0.303 0.368 0.340 0.274 y 0.287 0.353 0.380 0.316 6183 & 6283 Orange x 0.550 0.630 0.581 0.516 y 0.360 0.370 0.418 0.394 6184 & 6284 Green x 0.007 0.248 0.177 0.026 y 0.703 0.409 0.362 0.399 6185 & 6285 Blue x 0.144 0.244 0.190 0.066 y 0.030 0.202 0.247 0.208 6186 & 6286 Fluorescent red-orange x 0.610 0.535 0.570 0.655 y 0.390 0.375 0.340 0.344 6187 & 6287 Fluorescent lime-yellow x 0.387 0.356 0.398 0.460 y 0.610 0.494 0.452 0.540 6188 & 6288 Yellow x 0.498 0.557 0.479 0.438 y 0.412 0.442 0.520 0.472 6189 & 6289 Red x 0.655 0.569 0.595 0.690 y 0.345 0.341 0.315 0.310 Performance While use of 3M Scotchlite Reflective Material enhances visibility, no reflective material can guarantee absolute visibility, particularly in adverse weather conditions. Performance will vary depending upon actual use, exposure condition and maintenance. Users should test reflective material to satisfy conformance to their own requirements. Application Instructions Whenever two or more pieces of Scotchlite reflective material - series 6100 high gloss trim and Scotchlite reflective material - series 6200 high gloss film are used together on a single surface or as a set, they should be matched to ensure uniform color and reflectivity. Sewing to Fabrics: Sew in place with no more than 8 stitches per inch (2.54 cm), and not less than 1/8 (3mm) from the edge of the material. Thread recommendation: 100% polyester. To reduce sticking, apply a non-stick material (e.g., silicone or nylon) to the bottom of the presser foot. Welding to Fabrics: Scotchlite reflective material - series 6100 high gloss trim and Scotchlite reflective material - series 6200 high gloss film are composed primarily of vinyl materials and will weld suitably to most PVC films with any of the following methods: radio frequency (RF), high frequency (HF), dielectric, or ultrasonic. Adhesion to specific films will vary with the lubricants, pigments, plasticizers, and fillers used to make the PVC film. It is important for the user to test adhesion with each new lot and new vendor. RF Sealing: The most widely used method of sealing is RF. It has the advantage of being able to handle patches and trims using a step-and-repeat
process. This allows for the equipment to be used for a wide range of uses at a very economical price. Typically the price for this equipment will range from $20,000 to $50,000. For more information, please refer to our 3M Scotchlite Reflective Material High Gloss Film Application Guide for Welding. Screen Printing: Below are several inks that can be used for printing on top of the vinyl surface of 3M Scotchlite Reflective Material - Series 6100 High Gloss Trim and 3M Scotchlite Reflective Material - Series 6200 High Gloss Film. All inks should be continuously tested to ensure acceptable adhesion in the event of changes occurring in the manufacturing process or composition of the ink. Prior to printing, wiping the surface with a soft cloth lightly dampened with alcohol may help ink adhesion. Ink Ink Type Manufacturer 3M Scotchlite Transparent 3M Traffic Control Process Color Materials Division Series 990 Intl: 651-733-8726, 1-800-553-1380, Fax: 651-733-5012 3M Scotchcal Transparent 3M Commercial Screen Printing Graphics Division Ink Series 9700 UV Intl: 651-737-3136, 1-800-328-3908, Fax: 651-736-4233 9700 Series - All Opaque & Naz-Dar/KC Coatings Purpose Screen Ink Transparent Ph: 312-943-8338, Fax: 312-943-8215 3M Scotchcal Transparent 3M Commercial Screen Printing Graphics Division Ink Series 4400 Intl: 651-737-3136, 1-800-328-3908, Fax: 651-736-4233 NOTE: Scotchlite reflective material - series 6200 high gloss film is shipped with a polyester liner on top of the vinyl film for easy handling. This polyester liner can be removed either before or after the RF sealing process, but before sewing or screen printing. NOTE: Scotchlite reflective material - series 6200 high gloss film does not require a sealing film to be retroreflective. However, we do recommend the application of a sealing film to keep out dirt and water that could result in decreased reflectivity. NOTE: Dyes may migrate when placed in direct contact with vinyl and some fabrics. Prior to application, Scotchlite reflective material - series 6100 high gloss trim and Scotchlite reflective material - series 6200 high gloss film must be kept separate and should be tested for dye migration. Care and Maintenance Instructions Important: Test each application according to appropriate care instructions required for the finished product. Actual life of Scotchlite reflective material - series 6100 high gloss trim and Scotchlite reflective material - series 6200 high gloss film depends on cleaning method and wear conditions. Wash: Machine wash, 60 C (140 F) Bleach: Do not bleach Dry: Tumble dry medium, 50 C (122 F) Iron: Do not iron Dry-clean: Do not dry-clean
Product Availability 3M Scotchlite Reflective Material - Series 6100 High Gloss Trim and 3M Scotchlite Reflective Material - Series 6200 High Gloss Film are available in rolls with the following standard widths and lengths: Product Width Width Splices Standard Number Tolerance Allowed Roll Length 6100 1, 1 3/8, 1.5, ±1/32 2 per 100 yd. & 2, 25 mm, (±0.8 mm) roll max. 100 m 50.8 mm, 70 mm 6100 51.5 mm ±0.5 mm 2 per 100 m roll max. Order and Product Information To order 3M Scotchlite Reflective Material Products, contact 3M Personal Safety Products Department Customer Service at 800-328-7098 Ext. 2. Storage and Shelf Life Store in a cool, dry area and use within two years after date of receipt. Store rolls in original shipping cartons. Return partially used rolls to the carton or suspend horizontally through the core. Cut sheets should be stored flat. 6200 89 cm +6.4 mm, none 50 m -0 mm
Important Notice to Purchaser: Except where prohibited by law, 3M makes the following limited warranty in place of any others, express or implied, including any implied warranties or conditions of MERCHANTABILITY or fitness for a particular purpose or any implied warranty or condition commonly found in the industry: 3M shall replace or, at its option, refund the price paid to 3M for any 3M Scotchlite Reflective Material or other 3M reflective products ( Products ) which at the time of shipment to 3M s purchaser do not meet 3M s published Product specifications. Because of the unlimited variety of potential applications for Products, BEFORE production use, the User (which may be a converter or end product manufacturer or others) must determine that the Products are suitable for the intended use and are compatible with other component materials. User is solely responsible for determining the proper amount and placement of Products. While reflective Products enhance visibility, no reflective product can ensure visibility or safety under all possible conditions. 3M shall not be liable in contract or in tort, for any indirect, incidental, special, or consequential damages (including, without limitation, lost profits, goodwill and business opportunity) relating to the use or inability to use the Products. 3 Personal Safety Products Department 3M Safety and Security Systems Division 3M Center, Building 225-4N-14 St. Paul, MN 55144-1000 800-328-7098, Ext. 2 3M Canada P. O. Box 5757 London, Ontario, Canada N6A 4T1 800-364-3577 3M Mexico Avenida Santa Fe #55 Col. Santa Fe, CP01210 Delegacion Alvaro Obregon Telephone: 270-21-62 Fax: 270-22-94 10% post-consumer waste paper Printed in the USA. Copyright 1999, 3M IPC. All rights reserved. 75-0500-3167-5