C7040 C704 Designed for back-thinned CCD area image sensor The C7040 and C704 are high sensitivity multichannel detector heads for use with back-thinned CCD area image sensors (S700/ S70 series, S500-007, S50-007S) that offer high UV sensitivity and quantum efficiency. The C7040 is designed for the non-cooled type (S700 series, S500-007), while the C704 for the one-stage TE-cooled type (S70 series, S50-007S) for detection at even lower light levels. Both the C7040 and C704 incorporate a low-noise driver/amplifier circuit that provides reliable operation from simple external signals. The C704 also includes a highly stable temperature controller that cools the sensor to a preset temperature level (Ts=-0 C) as soon as the power is turned on. If the cooler fails and causes internal circuitry to overheat, the built-in protection circuit automatically turns off the power to the thermoelectric cooler. Despite its compact size, the housing configuration is designed for good heat dissipation, and threaded mounting holes on the front panel allow connections to other devices such as monochrometers. The table (P.) shows back-thinned CCD image sensors for the C7040 and C704. The C7040 and C704 do not come with a CCD image sensor, so select the desired sensor and order it separately. Controller for multichannel detector head C7557-0 is also available. The software supplied with the C7557-0 allows easy control of the multichannel detector head and data acquisition. Features Designed for back-thinned CCD area image sensor* C7040: for non-cooled type (S700 series, S500-007) C704: for TE-cooled type (S70 series, S50-007S) Line binning operation* /area scanning operation Driver/amplifier circuit for low noise CCD operation Highly stable temperature controller (C704) Cooling temperature: -0 C ± 0.05 C Simple signal input operation Compact configuration Applications Fluorescence spectroscopy Raman spectroscopy Other low-light-level detection *: In normal CCD image sensors that receive light from the front surface, the active area is covered with electrodes for charge transfer. These electrodes cut off UV radiation incident on the image sensor and also reduce the quantum efficiency. In contrast, back-thinned CCD image sensors have a unique structure in which the back of the active area is finely ground to allow light to enter from the back surface. This structure ensures high UV sensitivity and quantum efficiency because incident light need not pass through the electrodes. *: The CCD area image sensor can be operated like a linear image sensor having a large active area by transferring all the pixel signals in the vertical direction to the horizontal register (this is referred to as line binning). www.hamamatsu.com
Selection guide The table below shows CCD area image sensors applicable for the C7040 and C704. Since the C7040 and C704 do not include a CCD area image sensor, so select the desired sensor and order it separately. Type no. C7040 C704 CCD area image sensor Type no. Number of pixels Number of effective pixels Image area [mm (H) mm (V)] S700-0906 5 64 5 58.88.9 S700-0907 5 8 5.88.98 S700-0908 5 56 5 50.88 6.000 S700-006 044 64 04 58 4.576.9 S700-007 044 8 04 4.576.98 S700-008 044 56 04 50 4.576 6.000 S500-007 044 8 04 4.576.98 S70-0906S 5 64 5 58.88.9 S70-0907S 5 8 5.88.98 S70-0908S 5 56 5 50.88 6.000 S70-006S 044 64 04 58 4.576.9 S70-007S 044 8 04 4.576.98 S70-008S 044 56 04 50 4.576 6.000 S50-007S 044 8 04 4.576.98 Note: CCD multichannel detector head C704 for two-stage TE-cooled CCD area image sensor S70-006/-007/-008 is also available. Absolute maximum ratings Parameter Symbol Min. Typ. Max. Unit Supply voltage (for digital circuitry) VD -0.5 - +7 VA+ - - +8 Supply voltage (for analog circuitry) VA- - - -8 VA - - +0 VD - - +7 V Supply voltage Vp - - +7 VF - - +4 Digital input voltage - - - VD (, ) Operating temperature C7040 0 - +50 Topr C704 +0 - +5* C7040-0 - +70 Storage temperature Tstg C704 0 - +50 C *: The maximum value may be lower, depending on the drive frequency and the number of sensor pixels. Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Electrical characteristics (Ta=5 C, VD=+5 V, VA+=+5 V, VA-=-5 V, VA=+4 V, VD=+5 V, Vp=+5 V, VF=+ V, unless otherwise noted) Parameter Symbol Min. Typ. Max. Unit Digital input High level VIH +.0 - VD (, ) V Low level VIL -0.5 - +0.8 V CLK frequency fclk - - MHz Data video readout frequency fv - - fclk/4 Hz Start pulse width tst /fclk - - s Digital output High level (Io=-6 ma) VIH +.0 - - V Low level (Io=+6 ma) VIL - - +0.8 V Power supply operating conditions Digital circuitry VD +4.75 +5.0 +5.5 V VA+ +4.5 +5.0 +5.5 V Analog circuitry VA- -4.5-5.0-5.5 V Voltage VA +.5 +4.0 +4.5 V VD +4.75 +5.0 +5.5 V Other Vp +4.75 +5.0 +5.5 V VF +.75 +.0 +.5 V VD (+5 VDC) - - - +00 ma VA+ (+5 VDC) - - - +00 ma VA- (-5 VDC) - - - -00 ma Current VA (+4 VDC) - - - +0 ma VD (+5 VDC)* 4 - - - +0 ma Vp (+5 DC)* 4 - - - +.5 A VF (+ VDC)* 4 - - +00 - ma *4: C704
Electrical and optical characteristics (Ta=5 C, Ts=-0 C, VD=+5 V, VA+=+5 V, VA-=-5 V, VA=+4 V, VD=+5 V, Vp=+5 V, VF=+ V) Parameter Symbol Min. Typ. Max. Unit Spectral response range λ - 00 to 00 - nm Full well capacity Vertical 40 0 - Fw Horizontal 800 000 - ke - Conversion gain* 5 Sv - 5 - µv/e - Dark current* 6 C7040 (Ta=5 C) - 00 000 DS C704 (Ta=-0 C) - 0 e - /pixel/s Readout noise Nr - 0 - e - rms Dynamic range Drange - - - Photoresponse nonuniformity* 7 PRNU - ± ±0 % *5: Including the circuit gain *6: At MPP mode. Vertical register value. The actual value equals the sum of the vertical direction because of the binning operation. *7: Measured at 50 % of the full well capacity Specifications for temperature controller (C704) (Ta=5 C, VD=+5 V, VA+=+5 V, VA-=-5 V, VA=+4 V, VD=+5 V, Vp=+5 V, VF=+ V) Parameter* 8 Symbol Min. Typ. Max. Unit Cooling temperature Ts - -0-9 C Temperature control range Ts -0.05 - +0.05 C Power dissipation of TE-cooler element Pp - - 7 W Cool down time to reset temperature to - - 5 min Setting temperature for overheat protection* 9 To - +45 - C *8: Other functions include error display, automatic power off, and detection of electrical opens and shorts by the thermosensor. *9: Temperature on the rear of the case (where the fan is installed) Spectral response (without window) Quantum efficiency (%) 00 90 80 70 60 50 40 0 0 0 Front-illuminated CCD (Typ. Ta=5 C) S700/S70 series S500-007 S50-007S 0 00 400 600 800 000 00 Wavelength (nm) KMPDB008EC
Dark current vs. temperature 000 (Typ.) 00 Dark current (e - /pixel/s) 0 0. 0.0-50 -40-0 -0-0 0 0 0 0 Temperature ( C) KMPDB056EA Device structure (S700/S70 series) Thinning 5 0 4 -bevel V Thinning 4 45 45 H 4-bevel signal out n V=58,, 50 H=5, 04 4 5 8 9 0 Blank (4 pixels) n signal out Blank (4 pixels) 6-bevel 6-bevel KMPDC006EB 4
Block diagram (C704) P+ P- TE-cooler CCD area image sensor S70 series TH+ TH- OD RD OG IGH, IGH IGV, IGV PV, PV, TG PH, PH SG RG SS, ISV, ISH OS Regulator VDD VEE Driver Pre-amp Temperature controller * TH.H Inverter Clamp Timing generator LED Low-pass filter Buffer Vp (+5V) P.GND VD (+5V) VF (+V) F.GND Temp monitor Cooling control VD (+5V) VA+ (+5V) VA- (-5V) A.GND VA (+4V) Start CLK EOS Trigger Mode select Data video * The C7040 does not include the temperature controller and TE-cooler. KACCC0078EB 5
Timing chart (line binning operation) Start CLK PV PV TG PH PH SG RG Clamp EOS Trigger Data video V-ch V-ch V-ch(M) H-ch H-ch H-ch0 H-ch H-ch(N-0) H-ch(N-9) H-ch(N) M=64, 8, 56 N=5, 044 V-ch--V-ch, V-ch (M-)--V-ch (M): Isolation pixels H-ch--H-ch4, H-ch (N-)--H-ch (N): Blank pixels H-ch5--H-ch0, H-ch (N-9)--H-ch (N-4): Isolation pixels KACCC0079EC KACCC0079EC 6
Pin connections of "SIGNAL I/O" connector 5-pin D-sub connector 8 7 6 5 4 5 4 0 9 KACCC0069EA Pin no. Terminal name Description Mode select Digital input signal used to select between the line binning operation and area scanning operation. HCMOS compatible. High level or left open: line binning operation Low level: area scanning operation Data video Analog video output. Positive polarity. VA+ (+5 V) Analog power supply 4 VA- (-5 V) Analog power supply 5 VD (+5 V) Digital power supply 6 Start Digital input signal for initializing the circuit. HCMOS compatible. Positive logic. The interval of the Start pulses determines the integration time of the CCD image sensor. 7 CLK Digital input signal for operating the circuit. HCMOS compatible. Rising edge operation. 8 EOS Digital output signal for indicating end-of-scan of the image sensor. HCMOS compatible. Negative logic. 9 A.GND Analog ground 0 A.GND Analog ground VA (+4 V) Analog power supply Digital ground Digital ground 4 Digital ground 5 Trigger Digital output signal for A/D conversion. HCMOS compatible. Positive logic. Pin connections of "TE CONTROL I/O" connector (C704) 9-pin D-sub connector 5 4 9 8 7 6 KACCC0075EA Pin no. Terminal name Description VD (+5 V) Digital power supply Temp monitor Analog output signal of the temperature of the CCD image sensor Cooling control Digital input signal for starting to cool down. HCMOS compatible. High level or left open: cooling Low level: stand-by 4 Vp (+5 V) Power supply for the thermoelectric cooler in the CCD image sensor (Please use AWG 8 wire) 5 VF (+ V) Power supply for cooling fan 6 Ground 7 Ground 8 P.GND Power supply return of the thermoelectric cooler mounted in the CCD image sensor (Please use AWG 8 wire) 9 F.GND Power supply return for cooling fan Available for using same power supply (+5 V) for "+VD" and "+Vp" Caution: Do not connect "VD" and "Vp" together on the backside of the 9-pin D-sub connector. These may be connected (shorted) at the power supply end, not 9-pin D-sub connector. 7
Dimensional outlines (unit: mm) C7040.7 0.5 0. 4.0 Focal plane 00.0 6.0.0 90.0 80.0 60.0 50.0 Focal plane 8.0 50.0 (4 ) M depth 4 KACCA006EC C704 4.0 5.0.4 0.5 Focal plane 77.0 00.0 6.0.0 90.0 80.0 60.0 50.0 Focal plane 8.0 50.0 (4 ) M depth 4 KACCA006EC 8
Pin connections TE controller Power supply Controller VF (+V) F.GND VP (+5V) P.GND VD (+5V) Cooling control 9 8 7 6 5 4 I/O signal Pulse generator Power supply Controller CLK Start VD (+5V) VA+ (+5V) VA- (-5V) VA (+4V) A.GND Mode select 5 4 0 9 8 7 6 5 4 S/H or A/D Oscilloscope Analog input A.GND S/H input CH GND Ext.Trig GND KACCC0076EC Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions Disclaimer 9
Multichannel detector head controller C7557-0 When connected to a HAMAMATSU multichannel detector head and a personal computer, the C7557-0 allows easy control of the detector head and data acquisition by using dedicated software that comes with the unit. Suitable multichannel detector head C700/-0, C70/-0, C705/-0,, C704, C7044, C780, C78, C806-0, C806-0, C050, C05, C5964 series, C889 Accessories for C7557-0 Spare fuse (.5 A)* 0 AC cable to conversion adapter USB cable Detector head connection cables (for SIGNAL I/O and TE CONTROL I/O terminal of multichannel detector head) CD-R (MCD USB driver, software, operation manual) MOS adapter *0: Contained in the holder just above the AC cable connector on the C7557-0 rear panel. Connection example Shutter* timing pulse AC cable (00 to 40 V included with C7557-0) Trig. Dedicated cable (included with C7557-0) POWER SIGNAL I/O TE CONTROL I/O USB cable (included with C7557-0) Image sensor + Multichannel detector head C7557-0 PC (USB.0/.0) [Windows 7 (-bit, 64-bit)/ Windows 8 (64-bit)/ Windows 8. (64-bit)] KACCC040ED Information described in this material is current as of December 07. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 6- Ichino-cho, Higashi-ku, Hamamatsu City, 45-8558 Japan, Telephone: (8) 5-44-, Fax: (8) 5-44-584 U.S.A.: Hamamatsu Corporation: 60 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: () 908--0960, Fax: () 908--8, E-mail: usa@hamamatsu.com Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 0, D-8 Herrsching am Ammersee, Germany, Telephone: (49) 85-75-0, Fax: (49) 85-65-8, E-mail: info@hamamatsu.de France: Hamamatsu Photonics France S.A.R.L.: 9, Rue du Saule Trapu, Parc du Moulin de Massy, 988 Massy Cedex, France, Telephone: -() 69 5 7 00, Fax: -() 69 5 7 0, E-mail: infos@hamamatsu.fr United Kingdom: Hamamatsu Photonics UK Limited: Howard Court, 0 Tewin Road, Welwyn Garden City, Hertfordshire AL7 BW, United Kingdom, Telephone: (44) 707-94888, Fax: (44) 707-5777, E-mail: info@hamamatsu.co.uk North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 5 6440 Kista, Sweden, Telephone: (46)8-509 0 00, Fax: (46)8-509 0 0, E-mail: info@hamamatsu.se Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, int. 6, 000 Arese (Milano), Italy, Telephone: (9)0-9 58 7, Fax: (9)0-9 58 7 4, E-mail: info@hamamatsu.it China: Hamamatsu Photonics (China) Co., Ltd.: B0, Jiaming Center, No.7 Dongsanhuan Beilu, Chaoyang District, Beijing 0000, China, Telephone: (86) 0-6586-6006, Fax: (86) 0-6586-866, E-mail: hpc@hamamatsu.com.cn Taiwan: Hamamatsu Photonics Taiwan Co., Ltd.: 8F-, No. 58, Section, Gongdao 5th Road, East District, Hsinchu, 00, Taiwan R.O.C. Telephone: (886)0-659-0080, Fax: (886)0-659-008, E-mail: info@hamamatsu.com.tw 0 Cat. No. KACC04E7 Dec. 07 DN