Adaptabel AC Single Stroke Bells

Adaptabel AC Single Stroke Bells PLC Compatible 332 Series > Completely assembled, all hardware supplied > Universal Adaptaplate mounts directly on surface or electrical box > Shockproof die cast housing > Dustproof AGENCY APPROVALS > UL 464 Listed > FM Listed SPECIFICATIONS > Rated 400 hours at 50% duty cycle > Self-compensating solenoid plunger Adaptabel single stroke bells produce an individual, clearly defined note. When current is applied, the striker hits the gong once and stops. Coded, intermittent current may be used to cause the striker to hit the gong, pause and hit again for any given period. Ideal for use with momentary initiating contacts. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. See accessories on page 5-10. Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. See Accessories on page 5-10 for available options. > Corrosion resistant heat flowed epoxy finish 5-2

TECHNICAL INFORMATION 4 1/2" (114 mm) 4" Bell 2 13/32" (61 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 3 11/16" (94 mm) 10 1/2" (267 mm) 7 1/8" (181 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 332-4G5 24V AC 50/60 Hz 0.50 12 90 / 84 10 332-4N5 120V AC 50/60 Hz 0.10 12 250 332-6G5 24V AC 50/60 Hz 0.50 12 92 / 86 10 332-6N5** 120V AC 50/60 Hz 0.10 12 250 332-6R5 240V AC 50/60 Hz 0.05 12 1000 332-10G5 24V AC 50/60 Hz 0.70 16.8 98 / 92 5 332-10N5** 120V AC 50/60 Hz 0.14 16.8 130 *Gong Size in inches denoted by suffix in catalog number. ** Diode Polarized models avaiable. Order 332D-6N5 or 332D-10N5. Add "-R" for red. SIGNAL INPUT LOAD CHARACTERISTICS Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 332-4N5 120V AC 60 Hz 25 100 0.41/4.5 332-6N5 120V AC 60 Hz 25 100 0.40/4.6 332-10N5 120V AC 60 Hz 25 140 0.53/4.5 This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-3

Adaptabel AC Single Stroke Bells Explosionproof, NEMA Type 4 332EX Series > 6" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location AC single stroke bells produce a distinctive, loud, and clear individual note that is free of mechanical clatter. When current is applied, the striker hits the gong once and stops. Current may be coded to cause the striker to hit the gong intermittently. Ideal for use with momentary initiating contacts. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Used for coded signal applications such as paging. Also specified for timing, scheduling, and general alarm applications in: Refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-12

TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) Peak db at Cat No. Volts Current* 1m / 10 ft. Gong Size 332EX-6G5 24V AC 50/60 Hz 3.40A 92 / 86 6" (152 mm) 332EX-6N5 120V AC 50/60 Hz 0.43A 332EX-6R5 240V AC 50/60 Hz 0.20A 332EX-10G5 24V AC 50/60 Hz 3.40A 100 / 94 10" (254 mm) 332EX-10N5 120V AC 50/60 Hz 0.43A 332EX-10R5 240V AC 50/60 Hz 0.20A *Single pulse duration - 8 to 16 milliseconds 5-13

Adaptabel DC Single Stroke Bells PLC Compatible 333 Series > Universal Adaptaplate mounts directly on surface or electrical box > Indoor AGENCY APPROVALS > UL 464 Listed DC single stroke bells produce an individual, clearly defined note. When current is applied, the striker hits the gong once and stops. Coded, intermittent current may be used to cause the striker to hit the gong, pause and hit again for any given period. Ideal for use with momentary initating contacts. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. See AdaptaBel Accessories on page 5-10. 5-4

TECHNICAL INFORMATION 4" (102 mm) 4" Bell 2 15/32" (63 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 2 29/32" (74 mm) 10" (254 mm) 6" (152 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 333-4G1 24 0.30 7.2 90 / 84 73 333-6E1 12 0.60 7.2 18 333-6G1 24 0.30 7.2 92 / 86 73 333-6P1 125 0.06 7.5 1870 333-10G1 24 0.30 7.2 98 / 92 73 333-10P1 125 0.06 7.5 1870 *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 333-4G1 24V DC 5 300 1.57/0.0001 333-6G1 24V DC 5 300 1.72/0.0001 333-10G1 24V DC 5 300 1.3/0.000182 **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-5

Adaptabel AC Vibrating Bells PLC Compatible 340 Series > Universal Adaptaplate mounts directly on surface or electrical box > Weatherproof by adding appropriate back box > Completely assembled, all hardware supplied > Shockproof die cast housing > Dustproof AGENCY APPROVALS > UL 464 Listed > FM Listed > CSFM Certified SPECIFICATIONS AC vibrating bells produce a long continuous ringing sound. The striker continues to strike the gong in rapid-fire action as long as current is applied. Universal Adaptaplate mounts directly on surface or fits any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box, or any plaster cover with mounting holes on 2 3/4" (70 mm) centers. 6" and 10" bells also mount on 4" (102 mm) square boxes. Specified for timing, scheduling, paging and general alarm applications. 4" (102 mm) sizes recommended for quiet office areas. 6" (152 mm) sizes for moderate noise level areas such as general factory areas. 10" (254 mm) sizes for loud areas such as heavy machine shops. Available with full cast grids and protective grilles. May be weatherproofed with the addition of a weatherproof box. See AdaptaBel Accessories on page 5-10 for available options. > Self-compensating solenoid plunger > Rated 400 hours at 50% duty cycle > Corrosion resistant heat flowed epoxy finish 5-6

TECHNICAL INFORMATION 4" Bell 4 1/2" (114 mm) 2 13/32" (61 mm) 10" Bell 4 13/16" (122 mm) 6" Bell 7 1/8" (181 mm) 3 11/16" (94 mm) 10 1/2" (267 mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 340-4E5 12 0.620 7.4 94 / 88 13 340-4FM 16 0.460 7.4 22 340-4G5 24 0.310 7.4 50 340-4N5 120 0.062 7.4 1300 340-4R5 240 0.031 7.4 5000 340-6E5 12 0.700 8.4 98 / 92 8 340-6FM 16 0.500 8.0 13 340-6G5 24 0.350 8.4 30 340-6N5 120 0.070 8.4 700 340-6R5 240 0.035 8.4 2650 340-10G5 24 0.350 8.4 102 / 96 30 340-10N5 120 0.070 8.4 700 340-10R5 240 0.350 8.4 2650 *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 340-4N5 120V AC 60 Hz 25 62 0.095/4 340-6N5 120V AC 60 Hz 25 70 0.15/4 340-10N5 120V AC 60 Hz 25 70 0.15/4 **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE 1. Pull wires through center hole and connect to binding post. 2. Slip Adaptabel onto sturdy hanger and push home. 3. Tighten front screw to complete installation. (Two screws on 4 inch bells) 5-7

Adaptabel DC Single Stroke Bells Explosionproof, NEMA Type 4 333EX Series > 6" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location DC single stroke bells produce a distinctive, loud, and clear individual note that is free of mechanical clatter. When current is applied, the striker hits the gong once and stops. Current may be coded to cause the striker to hit the gong intermittently. Ideal for use with momentary initiating contacts. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Used for coded signal applications such as paging. Also specified for timing, scheduling, and general alarm applications in refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-14

TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) Peak db at Cat No. Volts Current* 1m / 10 ft. Gong Size 333EX-6G1 24V DC 3.50A 92 / 86 6" (152 mm) 333EX-6P1 125V DC 0.52A 333EX-10G1 24V DC 3.50A 100 / 94 10" (254 mm) *Single pulse duration - 8 to 16 milliseconds 5-15

AdaptaBuzzer TM AC and DC Models > Vibrating Armature > Universal Adaptaplate mounts directly on surface or electrical box > Plug-in convenience > Corrosion resistant heat flowed epoxy finish AGENCY APPROVALS > 340A Series UL 464 Listed > 340A Series FM Approved 340A & 343A Series Edwards vibrating AdaptaBuzzers are the finest, heavy duty buzzers available. The AC models are volume adjustable. Universal Adaptaplate mounts directly on any single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box. Buzzer plugs into receptacle on mounting plate. For flush mounting accessories see page 5-10. Used for timing, scheduling, and paging applications. Use wherever a relatively low decibel signal of a different tone is required. 2 1/4" (57mm) 5 1/16" (128mm) 5-28 DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. 340A-G5 24V 50/60 Hz 0.250A 6.0 28 76 / 70 340A-N5 120V 50/60 Hz 0.050A 6.0 725 340A-R5 240V 50/60 Hz 0.025A 6.0 2900 343A-E1 12V DC 0.330 4.0 9.4 68 / 62 343A-G1 24V DC 0.150 3.6 28 343A-M1 75V DC 0.065 4.9 360 343A-P1 125V DC 0.070 8.8 1000

Adaptabel AC Vibrating Bells Explosionproof, NEMA Type 4 340EX Series > 6", 8" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III > NEMA Type 4 Hazardous location AC vibrating bells produce a distinctive, loud, and clear ringing sound that is free of mechanical clatter. The striker continues to strike the gong in rapid-fire action as long as current is applied. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Specified for timing, scheduling, paging, and general alarm applications in refineries, gasoline storage and dispensing areas, petrochemical manufacturers, spray paint areas, aircraft hangers, grain dust areas in graineries and flour mills, and industrial firms using flammable liquids. SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-16

TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C C 1 1/4" (32mm) 1 7/16" (37mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers 6" ± 1/8" (152mm ± 3mm) Mounting Brackets Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 8" 5 1/16" 5 1/4" 1 5/8" (203mm) (129mm) (133mm) (41mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) RMS db at Cat No. Volts Current 1m / 10 ft. Gong Size 340EX-6G5 24V AC 50/60 Hz 0.210A 90/84 6" (152mm) 340EX-6N5 120V AC 50/60 Hz 0.041A 340EX-6R5 240V AC 50/60 Hz 0.021A 340EX-8N5 120V AC 50/60 Hz 0.041A 95/89 8" (203mm) 340EX-10G5 24V AC 50/60 Hz 0.210A 94/88 10" (254mm) 340EX-10N5 120V AC 50/60 Hz 0.041A 340EX-10R5 240V AC 50/60 Hz 0.021A 5-17

General Purpose Bells Solid Brass Shell 432 Series Compact single-stroke bell sounding a crisp, clean tone. For low cost, light duty installations in factories, institutions, offices, and OEMs. Uses include: doorbells, extension signals, warning bells, and audible annunciation. Ideal for end of cycle timing, signaling, and paging. > Low cost > 2 1/2" Solid Brass Shell > Low current drain permits long wire runs 1 1/4" (32mm) 2 1/2" (64mm) 1 1/2" (38mm) DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft 432-G5 24V AC 0.350 8.4 33.0 78 / 72 432-N5 120V AC 0.065 7.8 864.0 78 / 72 5-25

Adaptabel DC Vibrating Bells PLC Compatible 435 Series > Universal Adaptaplate mounts directly on surface or electrical box > Weatherproof by adding 449 back box > 4", 6" 8" and 10" gong sizes AGENCY APPROVALS > UL 464 Listed DC vibrating bells produce a long continuous ringing sound. The striker continues to strike the gong in rapid-fire action as long as current is applied. Universal Adaptaplate mounts directly on surface or fits any single gang box, 3 1/4" (83mm), 3 1/2" (89mm), or 4" (102mm) octogon box, or any plaster cover with mounting holes on 2 3/4" (70mm) centers. 6" and 10" bells also mount on 4" (102mm) square boxes. The DC vibrating bell can be used in outdoor applications when mounted on Cat. No. 449 weatherproof back box. See AdaptaBel accessories on page 5-10. Specified for timing, scheduling, and general alarm applications. 5-8

TECHNICAL INFORMATION 6" Bell 4" Bell 2 29/32" 2 15/32" (74 mm) (63mm) 4" (102mm) 6" (152 mm) 10" Bell 4 13/16" (122 mm) 8" Bell 3 11/32" (85mm) 10" (254 mm) 8" (203mm) db at DC Coil Cat No.* Volts Amps VA 1m / 10 ft. Res (Ohms) 435-4C1 6 0.250 1.5 96 / 90 11 435-4E1 12 0.125 1.5 96 / 90 40 435-4G1 24 0.062 1.5 96 / 90 155 435-4J1 32 0.047 1.5 96 / 90 275 435-4P1 125 0.012 1.5 96 / 90 3000 435-6C1 6 0.250 1.5 98 / 92 11 435-6E1 12 0.125 1.5 98 / 92 40 435-6G1 24 0.062 1.5 98 / 92 155 435-6J1 32 0.047 1.5 98 / 92 275 435-6K1 48 0.031 1.5 98 / 92 620 435-6P1 125 0.012 1.5 98 / 92 3000 435-6S1 250 0.008 2.0 96 / 90 6100 435-8C1 6 0.250 1.5 99 / 93 11 435-8E1 12 0.125 1.5 99 / 93 40 435-8G1 24 0.062 1.5 99 / 93 155 435-8P1 125 0.012 1.5 99 / 93 3000 435-10E1 12 0.125 1.5 100 / 94 40 435-10G1 24 0.062 1.5 100 / 94 155 435-10P1 125 0.012 1.5 100 / 94 3000 435-10S1 250 0.008 2.0 96 / 90 6100 *Gong Size denoted by suffix in catalog number. *Gong Size in inches denoted by suffix in catalog number. SIGNAL INPUT LOAD CHARACTERISTICS** Light Source Operating Max. off state Continuous on Surge (inrush/duration) Cat. No. Voltage leakage current (ma) Current (ma) Amps/milliseconds 435-4G1 24V DC 5 62 1.06/0.0001 435-6G1 24V DC 5 62 1.14/0.000125 435-10G1 24V DC 5 62 1.14/0.000125 **This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal. Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs. 5-9

Adaptabel DC Vibrating Bells Explosionproof, NEMA Type 4 435EX Series > 6", 8" and 10" gong sizes > Low power drain for efficient operation over long wire runs > Completely assembled > Weatherproof > Diode Polarized Models available for use in electrically supervised circuits AGENCY APPROVALS > UL 1203 Listed > UL Listed for Class I, Divisions 1 and 2, Groups B, C and D; Class II, Divisions 1 and 2, Groups E, F and G; and Class III Hazardous location DC vibrating bells produce a distinctive, loud, and clear ringing sound that is free of mechanical clatter. The striker continues to strike the gong in rapid-fire action as long as current is applied. Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads for power connections. Specified for timing, scheduling, paging, and general alarm applications in: Refineries, gasoline storage and dispensing areas, Petrochemical manufacturers, Spray paint areas, Aircraft hangers, Grain dust areas in granaries and flour mills, and Industrial firms using flammable liquids. > NEMA Type 4 SPECIFICATIONS > Adjustment free selfcompensating plunger > Corrosion resistant finish 5-18

TECHNICAL INFORMATION B Mtg. Bracket 3/16" (5mm) C A 1 7/16" (37mm) 1 1/4" (32mm) Mounting hole positions for 3/8" (10mm) diameter (max) fasteners with washers Gong Dimensions Size A B C 6" 4 1/16" 4 13/16" 5/8" (152mm) (103mm) (122mm) (16mm) 8" 5 1/16" 5 1/4" 1 5/8" (203mm) (129mm) (133mm) (41mm) 10" 6 1/16" 5 3/8" 2 5/8" (245mm) (154mm) (137mm) (67mm) 6" ± 1/8" (152mm ± 3mm) Mounting Brackets RMS db at Cat No. Volts Current 1m / 10 ft. Gong Size 435EX-6C1 6 1.520 435EX-6E1 12 0.520 435EX-6G1 24 0.240 89/83 6" (152mm) 435EX-6K1 48 0.110 435EX-6P1 125 0.040 435EX-6S1 250 0.023 435EX-8G1 24 0.290 435EX-8K1 48 0.110 92/86 8" (203mm) 435EX-8P1 125 0.040 435EX-8S1 250 0.023 435EX-10E1 12 0.520 435EX-10G1 24 0.290 95/89 10" (254mm) 435EX-10P1 125 0.040 435DEX-6G1 + 24 0.290 89/83 6" (152mm) 435DEX-8G1 + 24 0.290 92/86 8" (203mm) 435DEX-10G1 + 24 0.290 95/89 10" (254mm) + Diode polarized for use in electrically supervised circuits. CSFM Listed 5-19

General Purpose Miniature Bells AC and DC Models 13 Series > 1", 2" and 3" sizes > Long Life > Dust proof covers > Adjustable volume Compact size and pleasant sound make these bells desirable for use in offices, apartment houses, intercom and telephone signaling, machinery and other OEM uses. Suitable for AC powered security systems with battery standby. > Grounded frame > External binding posts > Chrome plate finish D B C A DC Coil db at Dimension Cat No. Size Volts Amps VA Res (ohms) 1 m / 10 ft. A B C D 13-1AB 1" 5-10 DC 0.35 2.0 10 (25 mm) 6-12 AC 0.50 4.0 10 70 / 64 1 1/4" 3/4" 3 1/8" 1 3/4" 13-1G1 24 DC 0.20 4.8 120 (32mm) (19mm) (79mm) (44mm) 13-1G5 24 AC 0.20 4.8 85 13-2AB 2" 5-10 DC 0.40 2.5 8 (51 mm) 6-12 AC 0.50 4.0 8 71 / 65 1 3/4" 1 1/16" 3 29/32" 2 1/32" 13-2G1 24 DC 0.25 6.0 90 (44mm) (27mm) (99mm) (52mm) 13-2G5 24 AC 0.25 6.0 56 13-3AB 3" 5-10 DC 0.60 3.5 5 (76 mm) 6-12 AC 0.40 3.5 5 73 / 67 3" 1 9/16" 5 7/8" 3 1/2" 13-3G1 24 DC 0.25 6 44 (76mm) (40mm) (149mm) (89mm) 13-3G5 24 AC 0.25 6 30 5-22

General Purpose Bells AC and DC Models 55 Series Economy single magnet bell. Exposed striker, vibrating bell comes with an enclosed grounded terminal and case. For low cost, light duty installations in factories, institutions, offices, and OEMs. Used as doorbells, extension signals, warning bells, and audible annunciators. Especially suitable for AC powered security systems with battery backup. > 4" and 6" gong sizes > AC and DC Models > Low Voltage > Gray finish > Low current drain permits long wire runs B C A DC Coil db at Dimension Cat No. Size Volts Amps VA Res (ohms) 1m / 10 ft. A B C 55-4AM 4" 6V DC 0.85A 5.1 2.2 4" 2 1/8" 7 3/8" (102mm) 8V AC 1.10A 8.8 2.2 74 / 68 (102mm) (54mm) (187mm) 55-4G5 24V AC 0.20A 4.8 20.0 55-6AM 6" 6V DC 0.80A 4.8 1.9 6" 2 5/8" 10 5/8" (152mm) 8V AC 1.00A 8.0 1.9 80 / 74 (44mm) (27mm) (99mm) 55-6G5 24V AC 0.20A 4.8 24.0 5-23

General Purpose Bells AC and DC Models > 3", 4" and 6" gong sizes > Low current drain permits long wire runs > Supplied with weatherproof gasket for outdoor applications > Corrosion resistant gray finish 156G Series Self-contained underdome monitor bell. Weatherproof, insulated, and grounded vibrating bell with concealed plunger. Mounts on 3 3/4" (95mm) bolt circle. For low cost, light duty installations in factories, institutions, offices, and OEMs. Uses include doorbells, extension signals, warning bells and annunciation. Suitable for AC systems with battery backup. B A db at Dimension Cat No. Size Volts Amps 1m / 10 ft. A B 156G-3AM 3" 6-8V DC 8-10V AC 0.80 156G-3AX (76 mm) 12-18V DC 0.20 3" 1 7/8" 156G-3G1 24V DC 0.15 78 / 72 (76mm) (48mm) 156G-3G5 24V AC 0.30 156G-4AM 4" 6-8V DC 8-10V AC 0.80 4" 1 7/8" 156G-4G1 (102 mm) 24V DC 0.15 82 / 76 (102mm) (48mm) 156G-4G5 24V AC 0.30 156G-6AM 6-8V DC 8-10V AC 0.80 156G-6AW 6" 20-24V DC 0.15 86 / 80 6" 2 5/16" 156G-6G1 (152 mm) 24V DC 0.15 (152mm) (59mm) 156G-6G5 24V AC 0.30 5-24

General Purpose Dixie Bell TM Fully Enclosed > Low voltage > AC and DC operation > Attractive snap-on covers > Enclosed binding posts > Corrosion resistant metallic finish 720 Series Low cost, non adjustable bell which may be operated off of a 590 transformer or DC power. Universal economy bell widely used in homes, apartment houses, plants, OEMs. Especially suitable for AC powered security systems with battery standby. For office installation, see Cat. No. 13 Series Bells on page 5-22 or Cat. No. 15 and 115 Series Buzzers on pages 5-34 and 5-35. For combination bell and buzzer see Cat. No. 730 Dixie Buzabel TM on page 5-38. 3" (76mm) 1" (25mm) 5 1/4" (133mm) DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft 720 6-8V AC 1.20A 7.0 1.5 84 / 78 3-6V DC 5-26

Nubel General Purpose Bells AC and DC Models 740 & 744 Series Low cost, non adjustable bell which may be operated off of a 590 transformer or DC power. Universal economy bell widely used in homes, apartment houses, plants, OEMs. Especially suitable for AC powered systems with battery standby. For office installation, see Cat. No. 13 Series Bells on page 5-22 or Cat. No. 15 and 115 Series Buzzers on pages 5-34 and 5-35. For combination bell and buzzer see Cat. No. 730 Dixie Buzabel TM on page 5-38. > AC and DC Models > Low Voltage > Exposed gong > Attractive snap-on covers > Enclosed binding posts > Corrosion resistant metallic finish B C A DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C 740 6-8V AC 1.20 7.0 1.5 84 / 78 2 1/2" 1 1/4" 5 3/4" 3-6V DC (64 mm) (32 mm) (146 mm) 744 6-8V AC 1.20 10.0 1.5 84 / 78 4" 1 3/4" 6 7/8" 3-6V DC (102mm) (44mm) (175mm) 5-27

Dixie Buzzer TM & Dixie Buzabel TM Low voltage > Low voltage > Attractive snap on covers > Fully enclosed > Satin aluminum finish > Cat. No. 725 - enclosed binding posts > Cat. No. 730 - enclosed terminals 725 & 730 Series The Cat. No. 725 is a low cost, fully insulated, non adjustable buzzer. The Cat. No. 730 is a low cost, non adjustable combination bell and buzzer with grounded frame. May be operated using AC power supplied by a 590 transformer or from DC power. See Transformer Catalog Page 11-2. Universal economy buzzer or bell and buzzer combination widely used in homes, apartment houses, plants, and OEMs. A 1" (25mm) B 5-36 DC Coil db at Cat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft A B 725 6V AC 1.20A 7.2 1.0 88 / 82 1 3/4" 2 3/4" (45mm) (69mm) 730 6V AC 0.7A 4.2 3 88 / 82 3" 5 1/4" 3-6V DC 1.4A 8 3 (76mm) (133mm) 6-8V AC 60 Hz 1.4A 8 3

Miniature Lungen TM Buzzer AC and DC Models 15 Series > Adjustable volume > Chrome cover; zinc plated base Compact, dependable buzzer designed for long life and trouble-free installations. For installation in commercial buildings, offices, and OEM applications. B C D A 5-34 DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D 15-0AJ 5-8V DC 0.2 1.2 10 6-10V AC 0.3 2.4 10 71.5 / 65.5 1 5/8" 1 15/32" 1/2" 1 13/32" 15-0G1 24V DC 0.1 2.4 120 (41mm) (37mm) (13mm) (36mm) 15-0G5 24V AC 0.2 4.8 85 15-1AB 5-10V DC 0.3 2 8 6-12V AC 0.45 3.5 8 2 1/8" 1 13/16" 19/32" 1 53/64" 15-1E1 12V DC 0.2 2.4 20 74 / 68 (54mm) (46mm) (15mm) (46mm) 15-1G1 24V DC 0.1 2.4 90 15-1G5 24V AC 0.25 6 56 15-2AB 5-10V DC 3.5 2 6 6-12V AC 3.0 3 6 75 / 69 2 5/8" 2 3/8" 15/16" 2 3/32" 15-2G1 24V DC 0.15 3.6 60 (66mm) (60mm) (24mm) (53mm) 15-2G5 24V AC 0.25 6 40 15-3AB 5-10V DC 0.3 2 5 6-12V AC 0.4 2.5 5 3" 2 1/2" 7/8" 2 3/8" 15-3E1 12V DC 0.2 2.4 20 80.5 / 74.5 (76mm) (64mm) (22mm) (60mm) 15-3G1 24V DC 0.2 4.8 44 15-3G5 24V AC 0.25 6 30

Miniature Lungen TM Buzzer AC Operation 115 Series Compact, dependable buzzer designed for long life and trouble-free installations. For installation in commercial buildings, offices, and OEM applications. > Adjustable volume > Chrome cover > Zinc plated base > Contact-less B C D A DC Coil db at Dimension Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D 115-1AC 8V AC 0.4 3.2 12.5 79 / 73 2 5/32" 1 9/32" 5/8" 1 25/32" 115-1G5 24V AC 0.2 4.8 80 (55mm) (32mm) (16m) (45mm) 115-2AC 8V AC 0.5 4 6.5 83 / 77 2 5/8" 1 11/16" 25/32" 2 3/32" 115-2G5 24V AC 0.2 4.8 45 (66mm) (43mm) (20mm) (53mm) 115-4AC 8V AC 0.45 4 3.6 86 / 80 3 7/16" 2 3/16" 1 1/8" 2 27/32" 115-4G5 24V AC 0.25 6 28 (87mm) (55mm) (28mm) (72mm) 5-35

Midi Vibrating Horns Compact size 118 & 123A Series Edwards 118 Series DC and 123A Series AC Midi Vibrating Horns are designed primarily for security systems and for signaling devices on an OEM basis. Supplied with mounting bracket and simply attaches to mounting surface using #8-32 screw. Used for security systems, office machines, low-voltage trouble alarms, home appliances, data monitoring systems, computers, and timing devices. > Low power drain > Compact size > Shock resistant > Easy surface mount installation SPECIFICATIONS > Temperature range: -40 to 180 F (-40 to 82 C) > Weight: 3 oz (85g) 3/16" (5mm) 2 1/32" (51mm) 1 3/4" (45mm) A 6" (152mm) 2 wires on AC DC Coil db at Width Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. (A dimension) 118-E1 12V DC 0.07A 0.84 25.5 92 / 86 1 11/64" 118-G1 24V DC 0.03A 0.72 102.0 (30mm) 123A-E5 12V AC 60 Hz 0.4A 4.8 10.0 92 / 86 1 3/16" 123A-G5 24V AC 60 Hz 0.2A 4.8 40.0 (30mm) 123A-N5 120V AC 60 Hz 0.04A 4.8 1200.0 5-37

Strap Mounted Buzzer Low power drain > High voltage Cat. No. 1064 > Adjustable volume > Zinc-plated finish > Low power drain permits long wire runs > 1064 has terminal connectors > 1065 has flying leads 1064 & 1065 Series Flush mounted, heavy duty buzzer designed for standard outlet box installation. The 1064 Series are provided with terminals for wiring connections. The 1065 Series are provided with flying leads for wiring connections Installs in standard outlet boxes using any standard wall plate. Low cost, quality buzzer widely used in homes, apartment houses, plants, and OEMs. AGENCY APPROVALS > UL 464 Listed 1" (25mm) 3 3/4" (95mm) 2 3/8" (60mm) 3 3/16" (81mm) 1 3/8" (35mm) Cat. No. 1064 Shown DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. 1064-G5 24V AC 50/60 Hz 0.25A 6 36 82 / 76 1064-N5 120V AC 50/60 Hz 0.05A 6 925 1064-R5 240V AC 50/60 Hz 0.025A 6 3600 1065-G5 24V AC 50/60 Hz 0.25A 6 36 82 / 76 1065-N5 120V AC 50/60 Hz 0.05A 6 925 1065-R5 240V AC 50/60 Hz 0.025A 6 3600 5-32

High Voltage Buzzer Low power drain 1066 Series Designed for standard outlet box installation. Provided with leads for wiring connections. Low cost, quality buzzer widely used in homes, apartment houses, plants, and OEMs. > High voltage > Adjustable volume > Zinc-plated finish > Low power drain permits long wire runs AGENCY APPROVALS > UL Recognized 1 1/4" (32mm) 13/16" (21mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. 1066-G5 24V AC 50/60 Hz 0.25A 6 36 80 / 74 1066-N5 120V AC 50/60 Hz 0.05A 6 925 1066-R5 240V AC 50/60 Hz 0.025A 6 3600 5-33

Flush-Call Strap Mounted Signals Low voltage 660 Series The Edwards 660 Series are compact, strap-mounted buzzers and bells designed for flush mounting in standard electrical boxes. > Low voltage > Easy flush mounting Designed for installation in standard outlet boxes. Requires a 590 transformer (page 11-2) and push button. Transformer and pushbutton may be mounted in same 3 gang outlet box with a minimum depth of 1 3/4" (44 mm) using a Cat. No. 593 transformer mounting plate (page 11-4). Used for residential and commercial door signals and interoffice communications and signaling. 660/661 662 Typical Wiring Diagram 1 3/4" (44mm) A 590 Transformer 8/10V AC 115V AC 3 5/8" (92mm) DC Coil db at Cat No. Name Voltage Current* VA Res. (ohms) 1m / 10 ft. Depth (A) 660 Ringcall TM Bell 8-10V AC 1.5A 15 4.75 86 / 80 1 3/8" (35 mm) 661 Buzacall TM Buzzer 8-10V AC 1.3A 13 6 86 / 80 7/8" (22 mm) 662 Tucall TM Bell/Buzzer 8-10V AC 1.5A 15 4.75 86 / 80 1 3/8" (35 mm) *Current ratings at 10V AC. 5-39

AdaptaBuzzer TM Weatherproof DC & AC Models B-8698 & B-8699 Series Edwards B-8698 & B-8699 AdaptaBuzzers are the finest, heavy duty buzzers available. Sound is produced by the hammer action of a vibrating armature against the cover and starts and stops instantly with current impulse. The cover is secured to the unit's cast box by a cast aluminum threaded ring and sealed with a neoprene gasket. Two mounting lugs are provided for wall mounting. A 1/2" (13mm) tapped conduit entrance is provided on one side for field wiring. Wiring connections are made in the base and the cover assembly plugs into a receptacle in the base. Ideal for use in areas where a louder signal would be distracting. Often used for timing, scheduling, paging, and general alarm applications. Typical indoor and weatherproof installations include construction sites, shipping docks, and paper mills. > Heavy gauge steel cover > Die cast aluminum housing > Vibrating armature > Gray finish AGENCY APPROVALS > B-8699 Series UL 464 Listed > NEMA Type 3R Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-8698-E1 12V DC 1.5 18 4.8 95/89 B-8698-G1 24V DC 1.0 24 21.5 75 db min. B-8698-P1 125V DC 0.2 25 103 B-8698-S1 240V DC 0.1 24 600 B-8699-G5 24V AC 60 Hz 1.1 26.4 5.0 95/89 B-8699-N5 120V AC 60 Hz 0.2 24 146 75 db min. 5-29

AdaptaBuzzer TM Explosionproof > Cast aluminum housing and cover > Corrosion resistant heat flowed powder epoxy finish AGENCY APPROVALS > UL 1203 Listed B-KM-8140 & B-8141 The Edwards B-KM-8140 & B-8141 series AdaptaBuzzers are quality, heavy duty AC & DC buzzers designed for use in hazardous locations. The sound is produced by the hammer action of a vibrating armature against the cover. The buzzers are provided with two mounting lugs for wall mounting. A 1/2" (13mm) tapped conduit entrance is provided on one side for field wiring. Wiring connections are made in the base of the unit and the cover assembly plugs into a receptacle in the base. For use in hazardous location areas where a distinctive, lower db buzzer signal is required for timing, scheduling, paging, and general alarm applications. Typical installations include petroleum plants, gas plants, grain elevators, flour and paper mills, textile plants, and tankers. Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) 5-30 DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-KM-8140-G5 24V AC 60 Hz 1.1 19.2 5.0 95 / 89 B-KM-8140-N5 120V AC 60 Hz 0.2 24 146 75 db min. B-KM-8140-R5 240V AC 60 Hz 0.1 24 750 B-8141-G1 24V DC 0.8 19.2 21.5 95 / 89

Mineguard TM Mine Buzzers MSHA Certified B-8140-M & B-8141-M The Edwards B-8140-M & B-8141-M Mineguard series are quality, heavy duty buzzers suitable for use on permissible mining equipment. They are available in AC and DC voltages. The sound is produced by the hammer action of a vibrating armature against the cast aluminum cover. A one piece cast aluminum cover provides an effective explosion-proof seal; the seal is secured by a hex screw in the cover. For power connections, the unit features an installed 33" (84mm) power cord and conduit hose constructed of flame retardant neoprene. The buzzer is provided with two mounting lugs for wall mounting. For use in all mining applications. Designed to withstand the constant vibration associated with mining equipment such as loaders, carriers, and conveyors. > Heavy duty cast aluminum housing and cover > Corrosion resistant heat flowed powder epoxy finish AGENCY APPROVALS > MSHA Certified No. X/P-3116-1 > Conforms with MSHA 30 CFR, Part 18 for methane and air mixtures Tap 1/2" (13mm) IP 5 1/2" (140mm) 6 3/8" (162mm) 5 3/8" (137mm) 2 holes 3/8" (10mm) dia. 3" (76mm) DC Coil db at Cat No. Volts Amps VA Res (ohms) 1m / 10 ft. B-8140-M-G5 24V AC 60 Hz 1.1 19.2 5.0 B-8140-M-N5 120V AC 60 Hz 0.2 24 146 95 / 89 B-8140-M-R5 240V AC 60 Hz 0.1 24 740 B-8141-M-G1 24V DC 0.8 19.2 21.5 95 / 89 B-8141-M-S1 250V DC 0.1 25 600 5-31

Lumatone Electronic Signals Audio or Audio/Visual E100 Series > Low cost and size > Solid state, long life > High impact polystyrene case > Pulsating audio or audio/visual models available > Terminal connections SPECIFICATIONS > Operating temperature range: -32 to 131 F (-0 to 55 C) > Frequency: 2.8 khz Edwards Lumatone signals are designed to demand attention in quiet and moderate noise areas. The signal s output can be varied by controlling the applied voltage. The signal s low power consumption makes them suitable for battery operated equipment and allows them to be turned on and off by integrated circuits, SCRs and transistors. Simply unscrew front housing and insert threaded portion through a 1 5/32" (29mm) panel hole. Screw front housing back on. Signal can accommodate panel thickness up to 3/16" (5mm). Used for security systems, computers, appliances and industrial, process control, communication and restaurant equipment. DECIBELS VS. VOLTAGE FOR LUMATONE AUDIO SIGNALS Typical at Normal Temperature 100 90 1.75"* (44mm) 1.31" (33mm) db at 1 foot 80 70 1.44" (37mm) 1.64" (42mm) 60 5-38 6 8 10 12 14 16 18 20 22 24 Volts DC *Does not include panel thickness Max. Operating Pulsating LED Cat No. Description Voltage Current VA Rate Intensity E102A Steady audio 12V DC 10 ma 0.12 N/A N/A 24V DC 18 ma 0.44 N/A E103A Pulsating audio 12V DC 10 ma 0.12 90 N/A 24V DC 18 ma 0.44 60 E104A Steady visual/audio 12V DC 16 ma 0.20 N/A 1.3 mcd 24V DC 30 ma 0.75 N/A E105AE Pulsating visual/audio 12V DC 16 ma 0.20 90 1.3 mcd 24V DC 30 ma 0.75 60