DATE: 04/03/2018 TO: The Contractor FROM: System Protection & Control Projects 20413 SUBJECT: Technical Specifications for Center Park APSTF Project PROJECT OVERVIEW This is a general specification that covers the work requirements for Center Park APSTF Project. Use this document in conjunction with the Cable Schedule, Cable Pull List, Wiring Diagrams (provided at a later date), Control House Power Panel Modifications (CP022LV3), Control House Plan View (CPL100), and other associated schematics/documentation that is given by JEA. SCOPE OF WORK JEA System Protection & Control Projects 20413 (SPCP) is requesting the Contractor to offload & install twenty (20) Control Panels. Procure run, and terminate AC/DC cable the new DC panels, and decommission and demolish existing Relay Control and DC panels. Perform terminations inside de-energized relay panels. Procure and install control house main tray system. Move or Relocate any interfering objects (furniture, boxes) prior to beginning work. SITE All work shall be performed at Center Park Substation (1895 Kernan Blvd, Jacksonville, Fl. 32216). 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7851/ SP&C Projects 20413
JEA POINT OF CONTACT & DEPARTMENT JEA point of contact and department for this work is: Muqeet S. Mujahid System Protection & Control Projects 20413 JEA Tower, 9 th Floor 21 West Church Street Jacksonville, Florida 32202 Phone: (904) 665-7222 Cell: (904) 625-4898 mujams@jea.com SCHEDULE OF WORK The Contractor shall mobilize after the issuance of Purchase Order (PO) from JEA. The Contractor is to note that this work shall be performed in phases dependent upon electrical outages granted by JEA s System Operations Control Center (SOCC). Therefore, once the outage has been granted by SOCC, The Contractor should have the ability to mobilize within 48-hour notice from JEA Project Manager. Once, the granted outage work has been completed The Contractor maybe asked to demobilize until the next outage has been granted. The Contractor shall follow Substation Construction Documents to determine the sequence of work. JEA has Electric System Security concerns, which require that this Work be completed on time. Therefore, time is of the essence. SEQUENCE OF WORK The Contractor shall provide all labor in order to have an orderly progression of this Work. The Contractor will be required to coordinate the Work Schedule with JEA SPCP department and the point of contact listed above. The Contractor shall be responsible for all 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7851/ SP&C Projects 20413
work coordination, timing, sequencing, and scheduling that is necessary to assure timely completion. Refer to all documentation to get familiarized with the sequence of this work. 1.0 CABLE SCHEDULE 1.1 The Contractor shall pull all cables as listed in the Cable Schedule. All control cable, Ethernet cable, coaxial, and fiber will be provided by JEA except cables from AC/DC source panels. The Contractor shall be responsible for providing these cables. 1.2 The Contractor shall pull all cable as listed in the Cable Schedule. 1.3 The cable should have sufficient slack such that they can be terminated to the new Relay Controls Panels and ample cable for making terminations. The cable should have enough slack to reach the floor of the panel and back to the top of control panel. 1.4 The Contractor shall leave enough slack in the cable to accommodate for any changes to the Control Panel(s) layout inside the control house. 1.5 Cable lengths listed in the Cable Schedule are approximate. The Contractor shall be responsible of all cable length prior to cutting. 1.6 The Contractor is responsible for providing the Owner with accurate As Built revision of the Cable Schedule. 1.7 The Contractor will be responsible for labeling all cables as listed in the Cable Schedule. 2.0 TERMINATIONS 2.1 The Contractor shall be responsible for all terminations into the new de-energized control panels. Wiring diagrams to be provided by JEA at a later date. The Contractor shall include cost of terminating twenty (20) JEA Standard cabinet style relay control panels. 2.2 The Contractor shall NOT do any terminations into any energized control panels. 2.3 Please note that coaxial and Ethernet cables procured by JEA are terminated by the manufacturer. 2.4 All fiber cable terminations shall be ST unless otherwise specified. 2.5 The Contractor shall be responsible for running and terminating all AC/DC cables from AC/DC load centers to the panels. 3.0 SPLICES 3.1 All run of control and instrument cable shall be continuous. Splices in control cable shall NOT be permitted. 4.0 LABELING OF CABLE The Contractor shall install all cables mentioned in the cable schedule and pull list as a part of this work. This shall require that the Contractor perform each of the following: 4.1 All cables are to be labeled: A. At both ends. 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7851/ SP&C Projects 20413
B. When entering and leave the cable trench. C. Where exiting station electrical equipment, to include all AC/DC power panels, power circuit breakers, junction boxes, etc. 4.2 Cable identification tags will be attached to the cable in a manner approved by JEA Project point of contact. The Contractor shall provide corrosion resistant tags for the cables. For exterior application plastic cable ties shall not be permitted. 4.3 Outdoor cable identification tags shall be ½ wide stainless steel, Dymo M1011 system, unless otherwise approved by the Project Representative. Indoor cable identification tags shall be RhinoPRO ½ flexible nylon labels black on white, Manufacturer part # 18488, unless otherwise approved by the Project Representative. Indoor labels shall be secure with two plastic ties. 4.4 All cable identification tags will have the appropriate cable number clearly stamped in no less than ¼ high characters. Cable names are specified on the Cable Schedule attached to these Specifications. 5.0 MATERIALS PICK UP 5.1 The Contractor shall be responsible to pick up cable reels from other JEA substations or various JEA Storerooms. 5.2 The Contractor shall be responsible for providing equipment and labor to pick up cable reels from above mentioned location and bring them to the site at Center Park substation. 5.3 The Contractor shall be responsible to drop unused cable/cable reels to JEA storeroom, location to be provided later. 6.0 CONTROL S Follow Center Park APSTF Project Construction Guidelines and Instructions documents for Control Panel placement sequencing. Work sequence shall be as follows: 6.1 JEA SPC tech will inform JEA SPCP Project Manager upon completion of the relay panel de-termination. 6.2 JEA SPCP project representative will then give The Contractor 48 hour notice to mobilize and commence their work of removing existing control panels which were de-terminated in 6.1 6.3 The Contractor will be responsible for removing existing de-terminated cable from the existing control panel and the panel itself. 6.4 Once existing control panels are removed. New control panels will be placed & bolted. 6.5 The Contractor shall be responsible for properly leveling the panels, and ensuring all access doors are operable. 6.6 The Contractor shall be responsible for connecting the control house ground to newly installed control panels. 6.7 All existing marked cables will be transferred over to the new Control Panel. 6.8 The Contractor shall be responsible for providing & installing wire-way, race-way or conduit system a rigid pathway for the cable to make transition between existing 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7851/ SP&C Projects 20413
substation cable tray and the new panels such that undue stress is not placed on the control cables such as RGS conduits. 6.9 The Contractor shall be responsible for modifying existing wire-ways and conduits to fit the new control panels. 6.10 All cables pulled to the control panels shall be sized to reach the floor of the panel and back to the top of control panel. 7.0 GPS ANTENNA INSTALLATION 7.1 The Contractor shall be responsible for appropriately mounting the GPS Antenna to the exterior of the Control House roof or wall as appropriate. 7.2 The Contractor shall be responsible for creating an appropriate opening for wiring from the GPS Antenna to be run inside the Control House via conduit if an existing opening is not available. 7.3 The Contractor shall be responsible for providing conduits and fittings needed for GPS antenna installation. 8.0 INVESTMENT RECOVERY SPCP will be coordinating internally with Investment Recovery Operations (IRO) in regards to the proper disposal of the scrap metal and control cable removed from service. All salvageable material, i.e. demoed copper cable, panels, relays, are property of JEA. When the Contractor commences work, there will be two scrap metal containers (one for the scrapped steel and one for the control cable) and it is the Contractor responsibility to perform the following: 8.1 The Contractor shall be responsible to properly dispose of the scrapped steel into the proper container that is located on site (JEA will have the containers properly labeled to prevent confusion). 8.2 The Contractor shall be responsible to properly dispose of the control cable into the proper container that is located on site (JEA will have the containers properly labeled to prevent confusion). 8.3 The Contractor shall NOT put any form of trash into the two scrap metal containers that are dedicated for scrap metal and control cable. 8.4 The Contractor shall be responsible for disposing of all trash that is a byproduct of their work regardless if the trash was created by material that was given by JEA such as empty cable reels. 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7851/ SP&C Projects 20413
SYSTEM PROTECTION & CONTROL PROEJCTS 20413 CABLE SCHEDULE UCABLE NOTES:U 1. TYPE B, BS, F, AND FO CABLE SHALL BE FURNISHED BY THE OWNER, UNLESS OTHERWISE SPECIFIED. 2. THE CONTRACTOR SHALL FURNISH ALL OTHER CABLE, AS SPECIFIED. 3. CONTRACTOR IS RESPONSIBLE FOR VERIFYING ALL CABLE LENGTHS. CABLE LENGTHS LISTED ARE APPROXIMATE. A - B - BS - C - F - FO - S - M - UCABLE LEGEND:U THHN INSULATED COPPER CONDUCTOR, RATED 600V CONTROL CABLE SHIELDED CONTROL CABLE RHW, THHW, OR THWN INSULATED COPPER CONDUCTOR, RATED 600V INSTRUMENT CABLE FIBER OPTIC CABLE SINGLE CONDUCTOR MULTIPLE CONDUCTOR FILE: CENTER PARK CABLE SCHEDULE DATE: 1/30/18 PAGE: 1 OF 3
CABLE SCHEDULE CABLE # FROM TO VOLT SIZE #C S/M TYPE LNGTH ckt ft CONDUIT # PAGE.: 2 OF 3 REMARKS CONTROL HOUSE AC POWER P3/AC AC POWER PNL PNL 3 600 10 3 M BS ~100 PNL 3 THRU 5 AC POWER P3P4/AC PNL 3 PNL 4 600 10 3 M BS ~25 PNL 3 THRU 5 AC POWER P4P5/AC PNL 4 PNL 5 600 10 3 M BS ~35 PNL 3 THRU 5 AC POWER P6/AC AC POWER PNL PNL 6 600 10 3 M BS ~100 PNL 6 THRU 8 AC POWER P6P7/AC PNL 6 PNL 7 600 10 3 M BS ~25 PNL 6 THRU 8 AC POWER P7P8/AC PNL 7 PNL 8 600 10 3 M BS ~35 PNL 6 THRU 8 AC POWER P9/AC AC POWER PNL PNL 9 600 10 3 M BS ~100 PNL 9 THRU 11 AC POWER P9P10/AC PNL 9 PNL 10 600 10 3 M BS ~25 PNL 9 THRU 11 AC POWER P10P11/AC PNL 10 PNL 11 600 10 3 M BS ~35 PNL 9 THRU 11 AC POWER P12/AC AC POWER PNL PNL 12 600 10 3 M BS ~100 PNL 12 THRU 14 AC POWER P12P13/AC PNL 12 PNL 13 600 10 3 M BS ~25 PNL 12 THRU 14 AC POWER P13P14/AC PNL 13 PNL 14 600 10 3 M BS ~50 PNL 12 THRU 14 AC POWER P15/AC AC POWER PNL PNL 15 600 10 3 M BS ~100 PNL 15 THRU 17 AC POWER P15P16/AC PNL 15 PNL 16 600 10 3 M BS ~25 PNL 15 THRU 17 AC POWER P16P17/AC PNL 15 PNL 17 600 10 3 M BS ~35 PNL 15 THRU 17 AC POWER P18/AC AC POWER PNL PNL 18 600 10 3 M BS ~100 PNL 18 THRU 20 AC POWER P18P19/AC PNL 18 PNL 19 600 10 3 M BS ~25 PNL 18 THRU 20 AC POWER P19P20/AC PNL 19 PNL 20 600 10 3 M BS ~35 PNL 18 THRU 20 AC POWER P22/AC AC POWER PNL PNL 22 600 10 3 M BS ~100 PNL 22 THRU 23 AC POWER P22P23/AC PNL 22 PNL 23 600 10 3 M BS ~50 PNL 22 THRU 23 AC POWER CONTROL HOUSE 125VDC BATTERY SYSTEM P3/DC1 3 DCP1 600 8 2 M C ~100 DC POWER P3/DC2 3 DCP2 600 8 2 M C ~100 DC POWER P4/DC1 4 DCP1 600 8 2 M C ~100 DC POWER P4/DC2 4 DCP2 600 8 2 M C ~100 DC POWER P5/DC1 5 DCP1 600 8 2 M C ~100 DC POWER P5/DC2 5 DCP2 600 8 2 M C ~100 DC POWER P6/DC1 6 DCP1 600 8 2 M C ~100 DC POWER P6/DC2 6 DCP2 600 8 2 M C ~100 DC POWER P7/DC1 7 DCP1 600 8 2 M C ~100 DC POWER P7/DC2 7 DCP2 600 8 2 M C ~100 DC POWER P8/DC1 8 DCP1 600 8 2 M C ~100 DC POWER P8/DC2 8 DCP2 600 8 2 M C ~100 DC POWER P9/DC1 9 DCP1 600 8 2 M C ~100 DC POWER P9/DC2 9 DCP2 600 8 2 M C ~100 DC POWER P10/DC1 10 DCP1 600 8 2 M C ~100 DC POWER
CABLE SCHEDULE CABLE # FROM TO VOLT SIZE #C S/M TYPE LNGTH ckt ft CONDUIT # PAGE.: 3 OF 3 REMARKS P10/DC2 10 DCP2 600 8 2 M C ~100 DC POWER P11/DC1 11 DCP1 600 8 2 M C ~100 DC POWER P11/DC2 11 DCP2 600 8 2 M C ~100 DC POWER P12/DC1 12 DCP1 600 8 2 M C ~100 DC POWER P12/DC2 12 DCP2 600 8 2 M C ~100 DC POWER P13/DC1 13 DCP1 600 8 2 M C ~100 DC POWER P13/DC2 13 DCP2 600 8 2 M C ~100 DC POWER P14/DC1 14 DCP1 600 8 2 M C ~100 DC POWER P14/DC2 14 DCP2 600 8 2 M C ~100 DC POWER P15/DC1 15 DCP1 600 8 2 M C ~100 DC POWER P15/DC2 15 DCP2 600 8 2 M C ~100 DC POWER P16/DC1 16 DCP1 600 8 2 M C ~100 DC POWER P16/DC2 16 DCP2 600 8 2 M C ~100 DC POWER P17/DC1 17 DCP1 600 8 2 M C ~100 DC POWER P17/DC2 17 DCP2 600 8 2 M C ~100 DC POWER P18/DC1 18 DCP1 600 8 2 M C ~100 DC POWER P18/DC2 18 DCP2 600 8 2 M C ~100 DC POWER P19/DC1 19 DCP1 600 8 2 M C ~100 DC POWER P19/DC2 19 DCP2 600 8 2 M C ~100 DC POWER P20/DC1 20 DCP1 600 8 2 M C ~100 DC POWER P20/DC2 20 DCP2 600 8 2 M C ~100 DC POWER P22/DC1 22 DCP1 600 8 2 M C ~100 DC POWER P22/DC2 22 DCP2 600 8 2 M C ~100 DC POWER P23/DC1 23 DCP1 600 8 2 M C ~100 DC POWER P23/DC2 23 DCP2 600 8 2 M C ~100 DC POWER
DATE: 04/03/2018 TO: THE CONTRACTOR FROM: System Protection & Control Projects 20413 SUBJECT: Construction Specifications for Center Park Substation Note 1: Any work performed without receiving a written electronic authorization from System Protection & Control Projects 20413 (SPCP), shall result in the contractor not being paid for all work performed without authorization. Note 2: It shall be the responsibility of the contractor to receive an electronic written authorization from JEA SPCP for any additional work, which may result in a change order. JEA SPCP Contact Information mujams@jea.com Muqeet Mujahid (904)-665-7222 (904)-625-4898 hamidd@jea.com Darrell Hamilton (904)-665-7137 (904)-207-4200 Note 3: Use this document in conjunction with the issued Cable schedule, Control House Plan, Control House Conduit Plant, Control House Conduit Details, AC/DC Low Voltage Plan & Details, Technical Specifications and other forms of documentation given by JEA for performing this work successfully. Note 4: THE CONTRACTOR shall follow instructions below to meet JEA SPCP s expectations. Due to strict system outages, THE CONTRACTOR shall ensure that their crews will be able to mobilize within 48 hours upon receiving notice from JEA SPCP Project Manager. Note 5: When reviewing the wiring diagrams, please follow the following conventions, WIRING DIAGRAMS TO BE PROVIDED AT A LATER DATE: Anything that is covered in a yellow hatch is considered removed and is not to be terminated into the panel. Anything that is done in blue is considered to be a note and is used merely to provide guidance If the wiring diagram is updated at later point, all changes will be shown in green. Note 6: All material is property of JEA. 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7137/ SP&C Projects 20413
SCOPE OF WORK JEA System Protection & Control Projects 20413 (SPCP) is requesting The Contractor to perform the following tasks for the Center Park substation: 1. The Contractor shall be responsible to pick up cable reels from other JEA substations or various JEA storerooms. 2. The Contractor maybe required to move interfering furniture items or boxes to make way for their work. 3. The Contractor shall offload twenty (20) relay panels once they arrive at Center Park substation. 4. The Contractor shall make all provisions and install the new twenty (20) Control Panel(s), remove existing panels and discard them in dumpster provided by Investment Recovery Operations. 5. The Contractor shall be responsible for all terminations into the new de-energized control panels wiring diagrams to be provided by JEA at a later date. The Contractor shall include cost of terminating twenty (20) JEA Standard cabinet style relay control panels. 6. The Contractor shall be responsible for procuring and running AC cables from the AC source to new relay control panels as per provided cable schedule. 7. The Contractor shall be responsible for procuring and running DC cables from the DC panels to new relay control panels as per cable schedule. The Contractor shall terminate all cables inside the new DC panels and de-energized relay panels. 8. The Contractor shall connect the panel ground to the control house ground. The Contractor shall be responsible to provide all equipment material to make these ground connections. 9. The Contractor shall put all the decommissioned equipment into the correct scrap metal container located on site for Investment Recovery Operation to pick up (NO trash is to put into the containers). 10. The Contractor shall dispose of all trash that is a byproduct of their work regardless if the trash was created by material that was given by JEA such as empty cable reels. 21 West Church Street, 9 th Floor/ Jacksonville, FL 32202-3105/ 904.665.7137/ SP&C Projects 20413
125 V.D.C. 125 V.D.C. BATTERY BANK No. 1 BATTERY BANK No. 2 225 AMP MAIN 225 AMP MAIN PNL#1 1 2 PNL#2 PNL#1 1 2 PNL#2 EAST BUS PNL#3 3 4 9T6T7 CONTROL PNL#12 EAST BUS PNL#3 3 4 9T6T7 CONTROL PNL#12 WEST BUS PNL#4 5 6 XFMR T7 PNL#13 WEST BUS PNL#4 5 6 XFMR T7 PNL#13 933 PNL#5 7 8 INTEGRATION PNL#14 933 PNL#5 7 8 INTEGRATION PNL#14 RTU No. 1 9 20A 20A 10 COMM C1 AND C2 FUTURE RTU No. 2 9 20A 20A 10 COMM C3 AND C4 PNL#21 11 12 XFMR T7LS PNL#15 PNL#21 11 12 XFMR T7LS PNL#15 919 PNL#6 13 14 XFMR T6LS PNL#16 919 PNL#6 13 14 XFMR T6LS PNL#16 926 PNL#7 15 16 851 PNL#17 926 PNL#7 15 16 851 PNL#17 XFMR T1 PNL#8 17 18 853 PNL#18 XFMR T1 PNL#8 17 18 853 PNL#18 DC LIGHT CIRCUIT 19 20A 100A 20 BATTERY CART BATTERY BANK No. 1 SPARE 19 20A 100A 20 BATTERY CART BATTERY BANK No. 2 PNL#31 21 22 21 22 PNL#30 PNL#31 PNL#30 PNL#33 23 24 23 24 PNL#32 PNL#33 PNL#32 918 PNL#9 25 852 PNL#19 918 PNL#9 25 852 PNL#19 XFMR T2 PNL#10 27 845 PNL#20 XFMR T2 PNL#10 27 845 PNL#20 XFMR T6 PNL#11 WEST BUS PNL#22 XFMR T6 PNL#11 WEST BUS PNL#22 EAST BUS PNL#23 EAST BUS PNL#23 D.C. NO. 1 D.C. NO. 2 SAVED BY: cikoj 3/7/2018 11:14:52 AM NO. REVISIONS TO DRAWING BY DATE APPROVED NO. REVISIONS TO DRAWING BY DATE APPROVED ENGINEERING DESIGNED CHECKED APPROVED DRAFTING PRELIMINARY FINAL DESIGN PLOTTED BY DATE SPCP 03/2018 DDH 03/2018 BY DATE CIKOJ 3/8/18 SCALE: NONE T7 & 918 ADDITIONS CONTROL HOUSE S 230kV/138kV LOW PROFILE SYSTEM PROTECTION & CONTROL PROJECTS 20413 IFB. NO.: DESIGN FILENAME: CP022LV3.DGN DRAWING NO.: SHEET NO.: CP022LV3
D.C. A.C. UNIT NO. 1 5'-0" 1 A.C. UNIT NO. 2 C H G #1 3'-6" FAULT 939 #1 934 #2 933 #3 919 #4 926 #5 XFMR T1 #6 918 #7 XFMR T2 #8 XFMR T6 #9 9T6T7 CONTROL #10 XFMR T7 #11 EAST BUS #12 WEST BUS #13 BATTERY ROOM#1 BATTERY ROOM#2 9'-6" C H XFMR. T1 #30 G #2 FEEDER #31 XFMR. T2 #32 9'-6" FEEDER #33 3'-6" COMM FAULT RTU 834 #21 INTEGRATION #23 854 #22 852 #20 853 #19 851 #18 XFMR T6 LS #17 XFMR T7 LS #16 EAST BUS #15 WEST BUS #14 5'-0" BATHROOM D.C. 2 A.C. "CH" SAVED BY: cikoj 3/8/2018 10:44:58 AM NO. REVISIONS TO DRAWING BY DATE APPROVED NO. REVISIONS TO DRAWING BY DATE APPROVED ENGINEERING DESIGNED CHECKED APPROVED DRAFTING PRELIMINARY FINAL DESIGN PLOTTED BY DATE SPCP 03/2018 DDH 03/2018 BY DATE CIKOJ 3/8/18 SCALE: NONE CONTROL HOUSE LAYOUT EQUIPMENT NAME SYSTEM PROTECTION & CONTROL PROJECTS 20413 IFB. NO.: DESIGN FILENAME: CPL100.DGN DRAWING NO.: SHEET NO.: CPL100