ava ntertainment nit ssembly nstructions Thank you for your purchase. Please follow the instructions below for correct assembly. B dowel x2 x8 H locking nut x22 Q x32 x10 x10 K bracket x P bolt x22 height adjuster x1 clip x L seal x R hinge x S T x2 bolt x 1 V W safety strap x1 x1 X Y wall anchor x1 wall x1 WR: ny furniture that is not anchored to a wall has the potential to tip over in certain circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake. ccordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor with all furniture sold and we recommend these are used to prevent your product tipping.the fixing device provided should fit most wall types, but please note that different wall materials may require different fixing devices from those supplied. Z nut x slide railx2 slide railx2 slide railx2 slide railx2 Hardware Supplied plastic wedge glide x x12 x12 washer x2 Wall Strap *We recommend using a lathead driver to tighten all locking nuts 100% before first use. Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%. Phillips & lathead drivers and hammer required 1
ava ntertainment nit ssembly nstructions 1 2 P ttach 1x bracket () to panel [] using 2x s (). ttach 1x bracket () to panel [] using 2x s (). Tighten with a driver. over each bracket with 1x clip () as shown. Q ttach 1x slide rail (P) to panel [] and secure with 3x s () as shown. ow insert 2x bolts () into panel []. ttach 1x slide rail (Q) to panel [] and secure with 3x s () as shown. ow insert 2x bolts () into panel []. 2
ava ntertainment nit ssembly nstructions 3 P 6 LP Q ttach 1 x slide rail (P) to one side of panel [] and secure with 3x s (). lip the panel over as shown. ttach 1x slide rail (Q) and secure with 3x s (). Tighten with a driver. nsert 2x bolts () into panel [6]. 3
ava ntertainment nit ssembly nstructions 6 6 6 ttach panel [] to panel [6] using 2x dowels () and secure with 2x locking nuts (). ttach panels [] and [] to panel [6] using x dowels () and secure with x locking nuts (). Tighten with a driver.
ava ntertainment nit ssembly nstructions 8 2 3 1 1 nsert 8x bolts () into the underside of panel [1]. ttach panels [2], [3], [] and [] to the bolts in panel [1] using 8x dowels () and secure with 8x locking nuts (). Tighten with a driver.
ava ntertainment nit ssembly nstructions 9 10 10 9 2 9 8 3 Slide down panels [9] and [10] along the grooves between panels [2], [3], [] and [] to form the back of the unit. ttach 2x brackets () to panel [8] using x s (). Tighten with a driver. over each bracket with 1x clip () as shown. 6
ava ntertainment nit ssembly nstructions 11 back slot 12 8 12 2 11 11 3 12 ttach panel [8] to the rest of the unit using 10x dowels () and secure with 10x s () as shown. Tighten with a driver. nsure slot in nut is facing incoming bolt. ttach panels [11] and [12] together using x nuts () and x bolts () as shown. Tighten with a driver.
ava ntertainment nit ssembly nstructions 13 13 T T 12 L K L 11 1 12 H 1 T 8 T K 1 L L ttach leg panels [11] and [12] to panel [8] using 10x s () and tighten with a driver. ttach leg support [13] to panel [8] as shown. Screw the height adjuster (H) onto the support leg [13]. ttach x plastic glides (T) to the legs using a hammer. ttach 2x hinges (L) to panel [1] and secure with x s (). ttach 1x seal (K) using 1x (). ttach 2x hinges (L) to panel [1] and secure with x s (). ttach 1x seal (K) using 1x (). Tighten with a driver. 8
ava ntertainment nit ssembly nstructions 1 T: f the doors are uneven or there is a gap in the middle, loosen or tighten the on the door hinge until they are sitting flush. 1 K 1 K 1 1 ttach door panels [1] and [1] at the hinges using x s (). Tighten with a driver. nsure the doors swing easily open and closed. f a clip () is not catching on the seal (K), adjust the magnetic end by twisting it outwards. 9
ava ntertainment nit ssembly nstructions K 18 18 19 B B 20 21 18 18 19 19 B B 19 S 18 R nsert x bolts () and attach 1x seal (K) using 1x () to panel []/[]. ttach side panels [18] and [19] using x locking nuts (). Slide base panel [20] down between the grooves of the side panels. ttach back panel [21] using x s (B). Turn drawer upside down and attach 1x slide rail (S) and 1x slide rail (R) to the side panels using x s (). Tighten with a driver. nsert drawers [] and [] into the unit as shown. nsure they slide smoothly and easily along the rails. 10
ava ntertainment nit ssembly nstructions 19 20 strap washer wall plug strap 1 washer 1 V Z 1 1 X Z Y W 1 1 ttach 12 x wedges () to the back of the unit as shown, and secure using 12x s (1). ow attach 1x safety strap (V) to the back edge of panel [1] using 1 x washer (Z) and 1 x (W). Tighten with a driver. nce assembled lift furniture into place, do not drag. se a drill to create a small hole lining up with the top of the safety strap (V). asten to wall using 1x wall plug (X), 1x washer (Z) and 1x (Y). nsure unit is balanced and steady before use. You re done, enjoy! 11