1300 Industrial Road, Unit #19 San Carlos, CA 94070 FREE CALL 1-866-695-5862 US & Canada info@lumascape.com LS553LED Via Ingrade IP68 IK10 The LS553LED is a rugged, side emitting marker light constructed of 316 marine grade stainless steel. This luminaire is ideal for pathways, pedestrian malls and other public spaces. Some models are also suitable for use in low speed traffic areas. The construction and technology used in this luminaire ensures a long service life. OPTIONAL Specifications Lamp Source Approved Use Control Options IP Construction Installation Types Drive-over Static Load 1 W LED White (4 300 K typical) Warm white (3 000 K typical) Blue (470 nm) Other colors by request Suitable for wet locations Suitable for use in poured concrete Inherently protected Type IC 0-10 V (current sourcing) PWM On-site or factory programmable brightness IP68 316 marine grade stainless steel Pre-Installation Blockout Concrete pour, drive-over etc. Direct Burial Landscapes, planters etc. With 8-aperture version and pre-installation blockout One aperture - 2 200 lb (1 000 kg) Two aperture - 2 200 lb (1 000 kg) Four aperture - 3 300 lb (1 500 kg) Eight aperture - 4 400 lb (2 000 kg) s are with pre-installation blockout only 3.1 (78 mm) LS553LED Via Ø 3.5 (90 mm) LS553LED-xxx-xx-x-21-xx ½" NPT adapter. Luminaire provided with 6.5 ft (2.0 m) hook-up wire. Impact IK10 for 8 aperture model Standard Inclusions Remote Transformers / Power Supplies Order separately MicroAntiLeach wire entry Refer to section for application specific options Ø 3.7 (94 mm) Ø 3.7 (94 mm) Ambient Operating Temperature Surface Temperature Photometrics -4 F to 122 F (-20 C to +50 C) 113 F (45 C) Refer to 11.0 (280 mm) 11.0 (280 mm) Any luminaire can become hot - take care with appropriate use and placement LS553LED-xxx-xx-x-23-3-xx Includes pre-installation blockout with a ½" NPT adapter. Luminaire provided with 1' (0.3 m) hook-up wire. LS553LED-xxx-xx-x-23-4-xx Includes pre-installation blockout with 2 x ½" NPT adapters. Luminaire provided with 1' (0.3 m) hook-up wire. C1107US 6 Sep 2013
LS553LED Via Ingrade One aperture (1 x 120º) Four aperture (4 x 85º) 0.5 (1 3 mm) Two aperture (2 x 120º) Eight aperture (1) (8 x 40º) (1) Drive over is only available in stainless steel 8 aperture with pre-installation blockout LS553LED Pre-Installation Blockout Version LS553LED LAMP FINISH APERTURES CONDUIT CONNECTION INPUT VOLTAGE Wattage Color LED 1 W White (4 300 K typ.) 1W4 Warm white (3 000 K typ.) Blue (470 nm) 1H6 1B4 Stainless steel Black, powder coated White, powder coated Silver, powder coated SS CB CW CS One 1 Two 2 Four 4 Eight 8 (1) (1) Drive-over with eight aperture version only. ½" NPT adapter c/w 1' (0.3 m) hook-up wire 2 x ½" NPT adapter c/w 1' (0.3 m) hook-up wire 23-3 23-4 120-277 V, 50/60 Hz 09 12-15 V, 60 Hz or 12-13 (1) 0-10 V or PWM Dimmable Driver, 12-15 V, 60 Hz or 12-13-DIM (1) (1) Requires appropriate transformer. LS553LED Direct Burial Version LS553LED 21 LAMP FINISH APERTURES CONDUIT CONNECTION INPUT VOLTAGE Wattage Color LED 1 W White (4 300 K typ.) 1W4 Warm white (3 000 K typ.) Blue (470 nm) 1H6 1B4 Stainless steel Black, powder coated White, powder coated Silver, powder coated SS CB CW CS One 1 Two 2 Four 4 Eight 8 ½" NPT adapter c/w 6.5' (2.0 m) hook-up wire 21 120-277 V, 50/60 Hz 09 12-15 V, 60 Hz or 12-13 (1) 0-10 V or PWM Dimmable Driver, 12-15 V, 60 Hz or 12-13-DIM (1) (1) Requires appropriate transformer. Dimmable Wiring Diagram Reference Voltage LED Color Control Type Wiring Diagram 13-DIM Single Color PWM 2,3,4 C1107US 6 Sep 2013
Wiring Diagrams Diagram 2-0-10 V Dimming Via Current Sourcing Module, or Pulse Width Modulated Dimming (PWM) - Low Voltage LED Luminaire with d5 Driver on Circuit 120-277 V LSLED-24V96W277 Power Supply + Current Sourcing 0-10 V Control Module (by others) OR 0-10 V + 0-10 V Note: Check maximum current output of the current sourcing module. DO NOT exceed. Assume 2 ma per luminaire on control circuit. Pulse Width Modulated (PWM) Control Device (by others) NOTE: Reversed dimming signal polarity connection at the PWM Control device is correct. Observe correct polarity connections in all other locations Use compatibility table to determine maximum number of luminaires the power supply can support. Diagram 3-0-10 V Dimming - Low Voltage LED Luminaire with d5 Driver on 12-15 V AC Circuit LS-TWM Remote Magnetic Transformer 12-15 V AC 120-277 V LSLED-24V12W277 Power Supply (suitable NEMA enclosure required - by others) LS6133 0-10 V to PWM Dimming Signal Converter NOTE: Reversed dimming signal polarity connection at the LS6133 is correct. Observe correct polarity connections in all other locations 0-10 V wall box dimmer 0-10 V + 0-10 V OR Other 0-10 V signal Use compatibility table to determine maximum number of luminaires the power supply can support. NOTE: The above diagrams are intended to show electrical pathways between luminaires and ancillary devices. These diagrams are not intended to show type or color of cord/wire, wire gauge or approved use of the cord/wire supplied with luminaires. Consult the luminaire-specific cutsheet or the factory for detailed specifications.
Wiring Diagrams Diagram 4-0-10 V Dimming - Low Voltage LED Luminaire with d5 Driver on Circuit 120-277 V LSLED-24V96W277 Power Supply + LS6133 0-10 V to PWM Dimming Signal Converter (suitable NEMA enclosure required - by others) NOTE: Reversed dimming signal polarity connection at the LS6133 is correct. Observe correct polarity connections in all other locations 0-10 V wall box dimmer OR Other 0-10 V signal Use compatibility table to determine maximum number of luminaires the power supply can support. NOTE: The above diagrams are intended to show electrical pathways between luminaires and ancillary devices. These diagrams are not intended to show type or color of cord/wire, wire gauge or approved use of the cord/wire supplied with luminaires. Consult the luminaire-specific cutsheet or the factory for detailed specifications.
Transformers and Power Supply Compatibility Transformers and Power Supplies for Low Voltage LED Luminaires The following list of transformers and power supplies are for use with luminaires specifically described as being compatible with either 12 V AC (wirewound only) transformers or with 12- power supplies. Compatibility will be noted in the ordering code of the luminaire concerned, and will typically be referenced by Voltage '13' or '13-DIM'. In the case of '13-DIM' additional components may be required. Refer to the applicable wiring diagram/s. Compatibility with each transformer or power supply is indicated by the value mentioned, representing the maximum number of luminaires that may be powered from each transformer or power supply. Please note, this does not take into consideration voltage drop or ampacity limits of the branch circuit. For assistance, please contact factory. Wall Mounted Landscape Lighting Transformers Wall Mounted Transformers Class 2 Power Supply Direct Burial Transformer LS-TWM-1-300 LS-TWM-2-600 LS-TWM-3-900 LS-TWM-50 LS-TWM-100 LS-TWM-150 LS-TWM-250 LSLED-24V96W277 LS-TDB1-300 Voltage, 60 Hz, 60 Hz, 60 Hz, 60 Hz, 60 Hz, 60 Hz, 60 Hz 120-277 V, 50/60 Hz, 60 Hz Voltage 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12/13/14/15 V 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12 V, 60 Hz 12.5 V, 60 Hz Wattage 1 x 300 W circuit 2 x 300 W circuits 3 x 300 W circuits 50 W 100 W 150 W 250 W 96 W 300 W LS553LED 96 192 288 16 32 48 80 2* - 40 96 *Minimum number of luminaires.
Transformer Specifications Transformers for Landscape Lighting Applications LS-TWM-1-300 300 W 12/13/14/15 V Circuits 1 Protection Electrostatic shield, magnetic breaker NEMA 3R Construction Stainless steel Dimensions H 17.6" (447 mm) W 6.8" (173 mm) D 6.19" (157 mm) 27 lb (12.3 kg) LS-TWM-3-900 900 W 12/13/14/15 V Circuits 3 Protection Electrostatic shield, magnetic breaker NEMA 3R Construction Stainless steel Dimensions H 18.6" (472 mm) W 7.8" (198 mm) D 6.19" (157 mm) 34 lb (15.5 kg) LS-TWM-2-600 600 W 12/13/14/15 V Circuits 2 Protection Electrostatic shield, magnetic breaker NEMA 3R Construction Stainless steel Dimensions H 17.6" (447 mm) W 6.8" (173 mm) D 6.19" (157 mm) 29 lb (13.2 kg) LS-TDB1-300 Magnetic transformer - direct burial 300 W 12.5 V Circuits 1 Protection Circuit breaker Approvals ETL (US and Canada) NEMA 12 Construction Reinforced composite Dimensions H 9" (229 mm) W 9" (229 mm) D 7" (178 mm) 8 lb (3.6 kg) Wall Mounted Transformers LS-TWM-50 or 240 V 50 W Circuits 1 NEMA 3R 4.4 lb (2 kg) LS-TWM-150 or 240 V 150 W Circuits 1 NEMA 3R 5.6 lb (2.5 kg) LS-TWM-100 or 240 V 100 W Circuits 1 NEMA 3R 4.8 lb (2.2 kg) LS-TWM-250 or 240 V 250 W Circuits 1 NEMA 3R 6.7 lb (3 kg)
Power Supply and Control Specifications Class 2 LED Power Supplies LSLED-24V96W277 Electronic DC power supply - wall mounted 120-277 V, 50/60 Hz 96 W / 4 A Circuits 1 Approvals CSA, CSA-US Location Wet location Dimensions H 12.32" (313 mm) W 2.54" (65 mm) D 1.67" (42 mm) 2 lb (0.9 kg) LSLED-24V12W277 Electronic DC power supply - NEMA enclosure required (by others) 120-277 V, 50/60 Hz 12 W / 0.5 A Circuits 1 Recognized, Class 2 IP rating IP66 Location Wet location Dimensions H 3.35" (85 mm) W 1.42" (36 mm) D 0.91" (23 mm) 0.282 lb (0.1 kg) Control Related Equipment LS6133 0-10 V to PWM translator - NEMA enclosure required (by others) 96 W max 4 A max Circuits 1 Recognized, Class 2 IP IP66 Dimensions H 5.2" (132 mm) W 1.3" (33 mm) D 1" (25 mm) 0.2 lb (0.1 kg) LS67100 DMX to PWM translator - dry location only 4 x 60 W max 4 x 2.5 A max Circuits 4 IP N/A Dimensions H 11.25" (286 mm) W 4.6" (117 mm) D 3.2 (82 mm) 0.5 lb (0.2 kg)