9-CHANNEL MULTIVIEW. Model SG8100 OPERATING INSTRUCTIONS. Ú >Before operating this unit, please read manual thoroughlyù 3

Transcription

1 9-CHANNEL MULTIVIEW Model SG8100 Ú >Before operating this unit, please read manual thoroughlyù 3 OPERATING INSTRUCTIONS

2 SAFETY Before using this product, please follow the safety guidelines listed below: Ú >This unit is designed for indoor use. To prevent electrical shock injury, and fire hazard, please do not place this product outdoors, or in the rain, or in humid surroundings such as in a bathroom, laundry room, basement, or near a pool area. Ú >Do not attempt to service this unit by disassembling the cabinet This may expose you to dangerous voltage and other hazards. Refer all servicing to a qualified service center or return to provided. Ú >Should any liquid or solid object fall into the cabinet, or if you notice an unusual smell or smoke during operation, turn off the power and unplug the unit immediately. Have the unit checked by a qualified technician before further operation. Continued use without proper servicing may result in electrical shock and fire hazard. Ú >Use and connect only the accessories supplied for the unit. Do not use any other unauthorized accessories. Ú >If the cabinet is cracked or produces noise due to negligence or mishandling, turn power off and unplug the unit. Contact local qualified service center, or manufacturer as soon as possible. Ú 1 Note: Please follow the safety guidelines. For any further safety questions about this unit, please contact manufacturer or a qualified service center. ÙpNOTEÚ J 1.This equipment has been certified and found to comply with the limits regulated by FCC, EMC and LVD. Therefore, it is designed to provide reasonable protection against interference and will not cause interference with other appliance usage. However, it is imperative that user follows this manual's guidelines to avoid improper usage which may result in damage to the unit, electrical shock and fire hazard or injury. 2.In order to improve the feature functions and quality of this product, the specifications are subject to change without notice from time to time. 1

3 CHAPTER TABLE OF CONTENTS PAGE 1. Product Introduction Unpacking the unit Basic operations and controls Location and function of controls Key Functions on the Remote Setting up and operating procedures Connecting the cables Setting up the home security with alarm system Channel Auto-sequencing Alarm trigger Troubleshooting General feature and specifications General feature Specifications... 18

4 1. Product Introduction The LOREX MULTIVIEW has the ability to divide and display pictures on a CCTV monitor. It can be connected to up to 9 security cameras. This unit is able to provide various types of picture compositions. Through operation from the remote control, the user is able to select the number of pictures to appear on the screen. The picture composition can be selected from one to up to 9 different pictures on the same screen. Dividing the pictures on the same screen is one of the most basic functions the MULTIVIEW has to offer. Another distinguishing feature is that it can be connected to any CCD camera in conjunction with any sensor (i.e., frequency or infrared sensor) to become an easy to use home security system with complete security functions. When a sensor, if used, senses any intrusion, the picture window will appear on your screen and an alarm with a beeping sound will alert the viewer. In addition to the above two outstanding features the MULTIVIEW also has a built-in clock for user set up of time/date. Additional Features: You can also connect other A/V equipment (such as a DVD or camcorder) to your LOREX Multiview. You will need an RCA/BNC coupler (not included) for each device you wish to connect. 3

5 2. Unpacking the unit The unit carton contains the following items. If any of these items are missing, please contact the dealer from whom you purchased the unit for prompt replacement or call Pro-Video. 1. MULTIVIEW SYSTEM 1 with 9 A/V inputs and VCR IN 1 A/V output to VCR 1 A/V output to TV 2. Remote Control 1 with 2 size AA Alkaline Batteries 3.RCA two-color A/V cable 1 4.ADAPTER 1 AC 120V IN/ O/P : 12V 1.5A OR AC 230V IN/ O/P : 12V 1.5A 4

6 3. Basic operations and controls 3-1. Location and function of controls ÙpFront Panel ON/STANDBY : Power on mode (running) or standby mode. 2. AL RS : Alarm Reset-Resets Multiview to normal state. 3. LIVE/TAPE : Select video source from either normal video input (LIVE) or VCR tape. 4. BELL MUTE & PANIC(2) : BELL MUTE : Turns buzzer sound off in case of alarm PANIC (2) : In an emergency, press the key twice to trigger all alarms & sensors. 5. IRR : Remote control sensor. 6. POWER : Power light indicator. 7. SEQ : Turns auto-sequence mode ON/OFF. 8. PROG : Channel programming. 9. MENU : Starts menu dialog session. 10. ENTER : Data entry key. 11. EXIT : Exit menu dialog. 12. PIP ON : Turns PIP window display ON/OFF. 13. CH : Main channel up/down key. 14. SUB : SUB channel up/down key. 14 NOTE N ote:fora detailed description offunction keys,please referto P7 & P8. 5

7 ÙpRear Panel A/V INPUT (BNC connector for video and RCA connectors for mono audio) 2. VCR Loop terminal 3. A/V output : 1. For VCR recording 2. For TV input 4. 12V/500mA DC generally for CCD camera power. 5. Sensor input terminal (normally closed) 6. Dry contact output, activated in case of alarm triggered. 7. DC power inlet. 6

8 3-2. Key Functions on the Remote (1) POWER Power on/off (2) MENU Gives you a list of options from which to choose. (3) 1 ~ 9 Numeric buttonsú J 1.Select equipment to be operated 2.Select the page number for the particular picture mode (4) PIP ON This key brings up both the main and window pictures simultaneously on the screen. Window picture appears on the right top corner of the screen. (5) ENTER Press this key after each selected choice from the MENU. (6) CH Ù 1 UP/DOWN key allows for selections on main screen. (7) This UP/DOWN key allows for SUB selections on the window screen. (PIP) (8) SEQ Press this button will toggle ON/OFF of auto-sequence mode. (2) (8) (1) (3) (4) (5) (6) (7) 7

9 3-2. Key Functions on the Remote (Cont d) (9) PROG Pressing this button will enable the system to start detecting every video channel for one cycle. A video channel with valid signal input is marked as activated, whereas a video channel with no signal input is marked as idle. In normal operation, an idle channel is shown in blue. (10) LIVE/TAPE Live indicates the normal video coming from 9 input terminals. TAPE indicates the video coming from the VCR Loop terminal. The key is used to switch the videos between normal input and VCR Loop. (11) BELL MT & (1) PANIC(2) In an alarm ( i.e.. any of PIR has been triggered) Multiview will start beeping. Press this key to turn the buzzer sound off. (2) In normal case ( no PIR has been triggered) Click this key twice to set Multiview in panic mode,( both the buzzer and output are turned on and the VCR starts recording. Note : the two clicks should not be longer than 1.5 sec apart. (12) AL RS Alarm Reset Press this twice within 1.5 sec to reset Multiview to normal, ( resumes screen display and stops VCR recording ) (13) EXIT Terminates the present selected choice and returns to the first choice. (9) (13) (11) (12) (10) 8

10 4. Setting up and operating procedures 4-1.Connecting the cables Note: (1) To change settings, press PROG Key to re-scan channels and to re-set active/idle channels. (2) When sensor is not triggered in an event of emergency, press PANIC(2) key twice successively to activate Multiview s internal buzzer, output 1, and output 2. Press AL RS key twice to cancel the activation. (3) When using a DC 12V output, be sure not to exceed 500mAmp or the operation of the Multiview may be affected. VCR VCR out VCR CCD CCD camera CCD CCD camera CCD CCD camera To VCR To TV TV Trigger VCR PIR power AC Adapter SIR EN Trigger SIREN 9

11 4-2. Setting up the home security with alarm system Operating Multiview MENU When key is pressed, screen displays the picture illustrated on the right. Press CH <up> and <down> keys to select 1-8 for function or setting. Functions 1-8 can also be accessed by pressing the numbers 1-8 directly. 1. SINGLE 2. TWIN 3. MULTI-PICTURE 4 4. MULTI-PICTURE 6 5. MULTI-PICTURE 9 6. SECURITY 7. DWELL 8. TIME/DATE (1) Press key number 1, screen displays a full screen size picture as illustrated on the right. Press CH <up> and <down> keys to select channels 1-8. CH1 (main) (2) Press key number 2, screen displays a split picture as illustrated on the right. Press CH <up> and <down> keys to select (MAIN) picture s channels 1-8. Press SUB <up> and <down> keys to select (SUB) picture s channels 1-8. CH1 (MAIN) CH2 (SUB) 10

12 (3) Press key number 3, screen displays a picture illustrated on the right. Press CH <up> and <down> keys to select (MAIN) picture s channels 1-9. MAIN channel is displayed in real time. Press SUB <up> and <down> keys to select (SUB) picture s channels. SUB 1-3 channels are displayed in auto sequence cycle. CH1 (MAIN) CH3 (SUB2) CH2 (SUB1) CH4 (SUB3) (4) Press key number 4, screen displays a picture illustrated on the right. Press CH <up> and <down> keys to select (MAIN) picture s channels 1-9. MAIN channel is displayed in real time. Press SUB <up> and <down> keys to select (SUB) picture s channels. SUB 1-5 channels are displayed in auto sequence cycle. CH1 (main) CH4 SUB3 CH2 SUB1 CH3 SUB2 CH5 CH6 SUB4 SUB5 (5) Press key number 5, screen displays a picture illustrated on the right. Press CH <up> and <down> keys to select (MAIN) picture s channels 1-9. MAIN channel is displayed in real time. MAIN and SUB 1-8 channels are displayed in auto sequence cycle. CH1 CH2 CH3 (MAIN) SUB1 SUB2 CH4 CH5 CH6 SUB3 SUB4 SUB5 CH7 CH8 CH9 SUB6 SUB7 SUB8 Note:1)In realtim e m ode (Single ortwin M ode ),w hen the video source is lost, the m ain channelscreen w ilturn red,and the sub channelw ilturn Blue 2)In M ulti-m ode (4/6/9 M ode ),when the video source is lost,the m ain channelscreen w ilturn red,and the sub channelw illturn black. 11

13 (6) Press key number 6, screen displays a picture illustrated on the right. SENSOR1 CH1 OFF Press CH <up> and <down> keys to move the flashing cursor. Moving sequence: ch1-off-ch2-off-ch3-off. Press SUB <up> and <down> keys to change row 2, the value alters among channels 1-9. Press SUB <up> and <down> keys to change row 3, the display switches between on/off. SENSOR2 CH2 OFF SENSOR3 CH3 OFF This menu is to set up the correspondence between sensor and input video channels. For example: SENSOR 2 CH3 ON When sensor #2 is triggered, the main window immediately displays the video of channel 3. (7) Press key number 7, the screen prompt the following text SEQ DWELL 15 ALR DWELL 15 Two values (time of sequencer dwell and alarm dwell) are left to setup. The value is adjustable. Use CH <up> and <down> keys to select items between SEQ DWELL and ALR DWELL. Use SUB <up> and <down> keys to alter item value. Each value can be selected from press EXIT key to quit this operation. 12

14 FO R NTSE/NO R TH AM ER ICAN SYSTEM S: (8) Press key number 8, the screen will prompt the following text. hh:hour AM hh:mm ON/OFF mm:minutes YY:Year MM:DD:YY MM:Month (N orth Am erican) DD:Day Press CH <up> and <down> to toggle between AM/PM. Then press ENTER. The cursor will move to Hour-field. Use CH <up> and <down> to change the value between Then press ENTER. The cursor will move to the first digit of Minute-field. Use CH <up> and <down> to change the value between 0 and 5. Then press ENTER. The cursor will move to the last digit of Minute-field. Use CH <up> and <down> to change the value between 0 and 9. Then press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the value of Day. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the value of Month. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the value of year. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to switch ON/OFF the display of Press EXIT to return normal screen display. Note:aftera powerfailure,the tim e/date screen willblink 00:00 (hh:m m ).You w ilneed to re-enterthe new tim e/date. 13

15 . FO R PAL/EUR O PEAN SYSTEM S: (8) Press key number 8, the screen will display the following text. hh:hour mm:minutes hh:mm ON/OFF YY:Year DD:MM:YY MM:Month (European system ) DD:Day Use CH <up> and <down> to change the number between Then press ENTER. The cursor will move to the first digit of the Minute-field. Use CH <up> and <down> to change the number between 0 and 5. Then press ENTER. The cursor will move to the last digit of the Minute-field. Use CH <up> and <down> to change the number between 0 and 9. Then press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the day. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the month. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to change the year. Press ENTER. The cursor will move to next field. Use CH <up> and <down> to switch ON/OFF Press EXIT to return normal screen display. 13 N ote:aftera pow erfailure,the tim e/date screen w illblink 00:00 (hh:m m )You w il need to re-enterthe new tim e/date. 5. Channel Auto-sequencing (1) Automatic video sequencing is only valid when the screen is displayed in SINGLE and TWIN mode. The incoming videos are displayed in real time when user enables automatic sequence by pressing <seq> button. The automatic sequence logic begins to switch videos in sequence. (2) When <seq> key is pressed, SEQ wording displays on the lower right corner of the screen. Press any key except LIVE/TAPE & Program key to cancel SEQ function. 14

16 6. Alarm trigger When any sensor is triggered: (1) Multiview s internal buzzer is activated. (2) Output 1 (NO and NC) is activated and triggers siren or light. (3) Output 2 (NO and NC) is activated and triggers VCR to be ON. For example : SENSOR 1 CH2 ON SENSOR 2 CH3 ON SENSOR 3 CH1 ON a. If screen is displayed in 4/6/9 mode, in an event of sensor #2 being triggered, screen changes display to SINGLE MODE picture. If sensor #1 is triggered following sensor #2, then the screen changes display to TWIN MODE picture. If sensor #3 is triggered following sensor #1 and #2, then sensor #1 picture displays on the <main> window, sensors #2 and #3 pictures display on the <sub> windows. The <sub> windows auto switch every 3 seconds. If all 3 sensors are activated, when AL DWELL time setting is less than 15 seconds, AL DWELL would be set at 15 seconds. When AL DWELL is over, 4/6/9 mode returns. b. If screen is displayed in Single/Twin mode, when AL DWELL is over, screen returns to Single Mode. (4) When sensor is triggered, date/time automatically displays on the screen. (5) When trigger is activated, <BELL MT> can be pressed to turn off Multiview s internal buzzer. (6) When trigger is activated, <AL RS> key can be pressed twice to turn off Mutiview's internal buzzer, output 1, and output 2. (7) When in 4/6/9 multi-picture mode, press the channel number key directly to access the matching channel s picture which appears in Single mode automatically for observation. Press the same number key to return to 4/6/9 multi-picture mode. 15

17 7. Trouble shooting Before operating the unit, please read this manual thoroughly. If you encounter problems with your unit, go through the check list below. Symptom Power light is not on Cause and Remedy Make sure power cord is connected to an D.C. INLET. No picture or sound Check that all CCD equipments power is switched ON. Check if all cable is connected correctly and securely Remote control does not operate Make sure batteries are installed properly Test battery condition NOTE Should any problem persist after you have made these checks, consult qualified service personnel. Do not attempt to open unit. Electrical shock or injury could result. 16

18 Design and specifications subject to change without notice.