Powerful blending and warping simplified

Transcription

1 HQView320/325/520/530 Projector edge blending and image warping Powerful blending and warping simplified The Optoma blending products, powered by industry leading technology from Calibre provides best-in-class blending and warping projection solutions. The unique collaboration between Optoma and Calibre ensures that traditionally time consuming and complex blending and warping projects are greatly simplified, reducing setup time.

2 HQView Series Edge blending explained Some applications call for an image that is brighter and higher resolution than can be provided by one projector. In this situation a single image can be created from multiple projectors but unless done well the image will show visible bands where the projected images overlap Edge-blending technology solves this problem by eliminating the visible banding and creating a single bright, high resolution image across the screen. Single projector, single image Single image, two projectors - image is bright but has a band because the image is not blended Single image, two blended projectors - A bright, high resolution image with no band

3 HQView Series Edge blending multiple projectors in an array makes it possible to create very bright, high-resolution very wide projection displays. By using the HQView320/325 or HQView520/530 you can precisely control multiple, edge-blended images seamlessly, quickly and easily. HQView320/325 and HQView520/530 Designed with the end-user applications in mind, the HQView Series let s you expertly edge-blend multiple, curved images seamlessly, on all four sides, for an unlimited number of projectors. Precisely control edge-blended images and warp displays to fit almost any projection surface flat or curved. The Optoma Advantage Traditionally blending solutions are time-consuming and complicated to set up with many incompatibilities between blending solutions and projectors. The Optoma blending solution removes this issue. Each Optoma ProAV projector model has been painstakingly tested with the HQView320/325/520/530 and a series of optimised presets developed that greatly reduces the complexity and time required to setup blending projects. If you do require help with your blending project, uniquely, the industry leading Optoma ProAv support team is on hand to support your complete blending project the blending boxes and the projectors as a single system. This greatly simplifies the support process for you and enables us to assist you get your blending projects back on track quickly and efficiently. For more than ten years Optoma has been one of the world s foremost projector designers and manufacturers - amongst the very few companies that focus exclusively on projectors. Today the Optoma range represents the evolution of projection expertise, honed and refined by manufacturing and supporting millions of projectors the world over. This knowledge and skill has been distilled into our products and support services which are designed specifically for demanding professional applications. Higher education Auditoriums Conference rooms Meeting rooms Lecture theatres Boardrooms Digital signage Post production Houses of worship Broadcast studios Stage shows Theatre Museums Large classrooms Live events Trade shows Exhibitions Projection Mapping

4 HQView320 HQV320 Harnessing the power of the Reon video processor from IDT, running state of the art HQV algorithms with expertly designed hardware and firmware from Calibre, HQView320 is a compact yet high performance image scaler with HDMI/DVI/Component/VGA input capability and HDMI/DVI output which provides stunning image quality for professional, broadcast and corporate AV users. HQView320 includes 4-sided soft edge blend for seamless blending of multiple projectors and flexible geometry correction functions able to correct image shape and projector misalignment by dragging and dropping each image corner, or by pin, barrel, rotation, or by keystone and rotation. Full warp mapping is also supported by HQView320. A flexible and intuitive PC application is included for easy warp map creation, or third-party generated warp maps can also be processed from automatic image alignment systems making HQView320 ideal for dual overlaid projector alignment in 3D projection systems. Best in class professional image processing in a compact affordable module Superior de-interlacing reduces image flicker and artefacts Remove picture noise from poor quality video sources, improve image detail Powerful geometry correction for off-axis projection, pin/ barrel and image rotation 4-Sided soft edge blend for tiling multiple projectors to produce large images Flexible warp mapping for curved screen projection, simulation and 3D alignment HDMI, DVI, VGA Analog, Component inputs for signals up 1080p & WUXGA HDMI/DVI output up to 1080p/WUXGA Flexible color calibration controls Gamma controls 10-bit signal inputs, 12-bit internal processing Selectable processing versus latency: best picture and low latency modes Latency as low as 0.25-frame progressive inputs, 1.25-frames interlaced inputs USB port for in-field firmware updates Programmable customer logo on menu TCP/IP remote control and Web Server Easy to navigate self-explanatory OSD menus Motion adaptive per pixel video de-interlacing, HD & SD Multi-directional diagonal de-interlace filter Automatic 3:2 & 2:2 pull-down detection with automatic film/video/video over film detection Chroma and Luma transient improvement Edge anti-aliasing 4-field full resolution SD & HD processing 4D Motion, Noise Adaptive HQV noise reduction for spatial and temporal noise Codec noise reduction for mosquito and block compression noise Powerful geometry correction capabilities Image rotation, pin/barrel correction 4-Sided soft edge blend Flexible warp mapping

5 HQView320 Inputs 1x Component analog video YPbPr(S) or RGBS/RGsB via 3 or 4 x BNC jack 1x DVI/HDMI with HDCP via DVI-I connector, supports HDMI with HDCP, 8/10/12 bit video compatible 1x VGA analog via DVI-I connector (common with DVI/HDMI input Supported video formats: HD 720p, 1080i, 1080psf (psf digital only), 1080p23.97/24/25/30, 1080p30, 1080p59.94, 1080p60 ED 480p, 576p SD 625i (576i), 525i (480i) Common Vesa graphics formats from 640x480 to 1920x1200 (with reduced blanking for 1920x1200 and 1600x1200 modes) Outputs 1x DVI/HDMI with HDCP (HDMI with deep color 8/10/12 bit support, via DVI connector.) 1x DVI/HDMI with HDCP via DVI-I connector, supports HDMI with HDCP, 8/10/12 bit video compatible 1x VGA analog via DVI-I connector (common with DVI/HDMI input) Supported Output formats: Common VESA formats from 640x480 to 1920x1200, 720p, 1080p Selectable I/O lock mode, or frame rate conversion mode Selectable aspect ratio conversion, or incoming aspect ratio preserve mode User Controls Remote control via RS232, TCP/IP API and Web Server. PC-based Warp Map Generator tool. Keypad for OSD menu access USB port for uploading software updates and new features. Power Requirements 12VDC@approx 1.5A, external VAC PSU included. Warranty 3-years return to base warranty covers parts and labour, shipping excluded. HQView model > Front LCD menu or OSD control OSD OSD OSD LCD DVI/HDMI Inputs x x x x Component Input x x x x Composite/S-Video Inputs - - x x VGA Analog Input x x x x HD-SDI Input G-SDI Input - - x x DVI/HDMI Output x x x x VGA Analog Output - - x x 3G-SDI Output - - x x 3G-SDI Audio embed/de-embed - - x x HQV Processing x x x x PIP/POP/PAP - - x x TCP/IP Control x x x x Low Latency Mode x x x x Flicker Filter for Interlaced Output Modes - - x x Geometry Correction, 4-Corner, Rotate x x x x Genlock (V-Lock) - - x x Pan, Zoom, Tilt x x x x Edge Blending x x x x Edge Blend Black Level Correction - x x x Auto pan/zoom/tilt of content for blending x x x x Projection Mapping/Warp x x x x

6 HQView325 HQV Scaler with Warp Mapping Edge Blend & HDMI/DVI In/Out Harnessing the power of the ReonTM video processor running state of the art HQVTM algorithms with expertly designed hardware and firmware from Calibre, HQView325 is a highly flexible warp and blend scaler for professional, broadcast and corporate AV users. HQView325 features 4-sided soft edge blend with multi-region black level correction for seamless blending of multiple projectors. It also includes flexible geometry correction functions able to correct image shape and projector misalignment by dragging and dropping each image corner, or by pin/barrel, rotation or by keystone and rotation. Full warp mapping is also supported by HQView325. A PC application is included for easy warp map creation or third-party generated warp maps can also be processed from automatic image alignment systems making HQView325 ideal for stacked projector alignment and curved screen multi-projector tiling. HQView325 has digital I/O compatible with DVI and HDMI including deep colour support. Best in class professional image processing in a compact affordable 1U format Improve video image quality with better detail and clarity Powerful geometry correction for off-axis projection, pin/ barrel, image rotation 4-Sided soft edge blend for tiling multiple projectors to produce large images Flexible warp mapping for curved screen projection, simulation and 3D alignment HDMI, DVI & VGA inputs with signal compatibility up to 1080p & WUXGA HDMI/DVI multifunction output Motion adaptive per pixel video de-interlacing, HD & SD Multi-directional diagonal de-interlace filter Automatic 3:2 & 2:2 pull-down detection with automatic film, video and video over film detection Chroma and Luma transient improvement Edge anti-aliasing 4-field full resolution SD & HD processing 4D Motion, Noise Adaptive HQV noise reduction for spatial and temporal noise Codec noise reduction for mosquito and block compression noise Direct input selection keys allow input selection without using menu system Flexible colour calibration controls Gamma controls Selectable processing versus latency: best picture and low latency modes Latency as low as 0.25-frame progressive inputs, 1.25-frames interlaced inputs I/O Lock and Free Run selectable output modes USB port for in-field firmware updates Programmable customer logo on menu TCP/IP remote control and Web Server Easy to navigate self-explanatory OSD menus Powerful geometry correction capabilities Pan, Zoom, Tilt Image rotation, pin/barrel correction 4-Sided edge blend with 48-bit processing & multi-region black level correction Flexible warp mapping

7 HQView325 Inputs 1x HDMI with HDCP support, 8/12 bit deep colour compatible. Audio de-embed from HDMI of SPDIF compatible formats 1x DVI with HDCP support 1x VGA Analog via 15HDD Supported video formats: HD 720p, 1080i, 1080psf, 1080p23.97/24/25/30, 1080p30, 1080p50, 1080p59.94, 1080p60 ED 480p, 576p SD 625i (576i), 525i (480i) Common VESA graphics formats from 640x480 to 1920x1200 (with reduced blanking for 1920x1200 and 1600x1200 modes) Outputs 1x DVI/HDMI with HDCP (HDMI with deep color 8/10/12 bit support, via DVI connector) 1x S/PDIF digital audio via RCA Supported Output formats: DVI/VGA common VESA formats 640x480 to 1920x1200, 720p, 1080p Selectable I/O lock or frame rate conversion mode Selectable aspect ratio conversion User Controls Remote control via RS232, TCP/IP API and Web Server. PC-based Warp Map Generator tool Keypad for direct input selection and control of common adjustments as well as OSD menu access. USB port for uploading software updates and new features Power Requirements VAC, 35W typical Warranty 3-years return to base warranty covers parts and labour. HQView model > Front LCD menu or OSD control OSD OSD OSD LCD DVI/HDMI Inputs x x x x Component Input x x x x Composite/S-Video Inputs - - x x VGA Analog Input x x x x HD-SDI Input G-SDI Input - - x x DVI/HDMI Output x x x x VGA Analog Output - - x x 3G-SDI Output - - x x 3G-SDI Audio embed/de-embed - - x x HQV Processing x x x x PIP/POP/PAP - - x x TCP/IP Control x x x x Low Latency Mode x x x x Flicker Filter for Interlaced Output Modes - - x x Geometry Correction, 4-Corner, Rotate x x x x Genlock (V-Lock) - - x x Pan, Zoom, Tilt x x x x Edge Blending x x x x Edge Blend Black Level Correction - x x x Auto pan/zoom/tilt of content for blending x x x x Projection Mapping/Warp x x x x

8 HQView520 HQV520 Harnessing the power of the ReonTM video processor from IDT, running state of the art HQV algorithms with expertly designed hardware and firmware from Calibre, HQView520 is a highly flexible image scaler and scan converter which provides stunning image quality for professional, broadcast and corporate AV users. HQview520 features 4-sided soft edge blend for seamless blending of multiple projectors and includes flexible geometry correction functions able to correct image shape and projector misalignment by dragging and dropping each image corner, or by pin/barrel, rotation or by keystone and rotation. Full warp mapping is also supported by HQView520. A PC application is included for easy warp map creation or third-party generated warp maps can also be processed from automatic image alignment systems making HQView520 ideal for dual overlaid projector alignment in 3D systems. HQView520 has 3G-SDI input and out connectivity with backwards compatibility with HDSDI and SDSDI. A Genlock input is provided for studio/staging, compatible with bi or tri-level sync or black & burst. Best in class professional image processing in a compact affordable 1U format Use as a routing switcher and universal interface for 3G-SDI, HD-SDI, DVI or HDMI switching and distribution systems, projectors and displays Improve video image quality with better detail and clarity Superior de-interlacing reduces image flicker and artefacts Remove picture noise from poor quality video sources Powerful geometry correction for off-axis projection, pin/ barrel, image rotation 4-Sided soft edge blend for tiling multiple projectors to produce large images Flexible warp mapping for curved screen projection, simulation and 3D alignment Genlock and I/O Lock for in-camera and edge blend use 3G-SDI, HDMI, DVI, VGA Analog, Component YPbPr, RGsB/RGBS, Composite & S-Video inputs with signal compatibility up to 1080p & WUXGA 3G-SDI, HDMI/DVI & VGA Analog outputs Motion adaptive per pixel video de-interlacing, HD & SD Multi-directional diagonal de-interlace filter Automatic 3:2 & 2:2 pull-down detection with automatic film, video and video over film detection Chroma and Luma transient improvement Edge anti-aliasing 4-field full resolution SD & HD processing 4D Motion, Noise Adaptive HQV noise reduction for spatial and temporal noise Codec noise reduction for mosquito and block compression noise Direct input selection keys allow input selection without using menu system Flexible color calibration controls Gamma controls 10-bit signal inputs, 12-bit accurate internal processing Selectable processing versus latency: best picture and low latency modes Latency as low as 0.25-frame progressive inputs, 1.25-frames interlaced inputs I/O Lock, Genlock/Frame Sync and Free Run selectable output modes Flicker filter for interlaced output modes USB port for in-field firmware updates TCP/IP remote control and Web Server Easy to navigate self-explanatory OSD menus Powerful geometry correction capabilities Pan, Zoom, Tilt Image rotation, pin/barrel correction 4-Sided soft edge blend Flexible warp mapping

9 HQView520 Inputs 2x Composite Video CVBS (NTSC, PAL & SECAM), 1x via BNC jack and 1x via Cinch/RCA 1x YC/S-Video via 4 pin mini DIN 1x Component analog video YPbPr(S) or RGsB/RGBS via 3 or 4 x BNC jack 1x HDMI with HDCP, 8/10/12 bit video compatible, 10-bit internal processing depth. Audio strip-off of SPDIF compatible formats 1x DVI with HDCP 1x VGA Analog via 15HDD 1 x 3G-SDI, accepts 3G, HD and SD SDI signals via BNC supports 4:2:2 and 4:4:4 formats with audio de-embed 1x Genlock (V-Lock) input via BNC, accepts bi-level, tri-level sync or black & burst, 50/59.94/60Hz formats Supported video formats: HD 720p, 1080i, 1080psf (psf digital only), 1080p23.97/24/25/30, 1080p30, 1080p50, 1080p59.94, 1080p60 ED 480p, 576p (not via SDI) SD 625i (576i), 525i (480i) Common VESA graphics formats from 640x480 to 1920x1200 (with reduced blanking for 1920x1200 and 1600x1200 modes) Multi standard support for CVBS & YC in PAL, NTSC, SECAM formats with selectable 3D comb for composite Note: PIP and edge blend are mutually exclusive so cannot be used simultaneously Outputs 1x 3G-SDI 1x DVI/HDMI with HDCP (HDMI with deep color 8/10/12 bit support, via DVI connector) 1x VGA Analog via 15HDD 1x S/PDIF digital audio via RCA NB: 3G-SDI and VGA Analog outputs are disabled with HDCPencrypted input. Not all outputs are available simultaneously Supported Output formats: DVI/VGA common VESA formats 640x480 to 1920x1200, 720p, 1080p 3G-SDI in SMPTE formats 480i, 576i, 720p, 1080i, 1080p with selectable audio embed Selectable Genlock (V-Lock), I/O lock or frame rate conversion mode Selectable aspect ratio conversion Selectable vertical temporal filter for flicker reduction of interlaced outputs (edge blend not available in this mode) User Controls Remote control via RS232, TCP/IP API and Web Server. PC-based Warp Map Generator tool Keypad for direct input selection and control of common adjustments as well as OSD menu access. USB port for uploading software updates and new features Power Requirements VAC, 35W typical Warranty 3-years return to base warranty covers parts and labor, shipping excluded. HQView model > Front LCD menu or OSD control OSD OSD OSD LCD DVI/HDMI Inputs x x x x Component Input x x x x Composite/S-Video Inputs - - x x VGA Analog Input x x x x HD-SDI Input G-SDI Input - - x x DVI/HDMI Output x x x x VGA Analog Output - - x x 3G-SDI Output - - x x 3G-SDI Audio embed/de-embed - - x x HQV Processing x x x x PIP/POP/PAP - - x x TCP/IP Control x x x x Low Latency Mode x x x x Flicker Filter for Interlaced Output Modes - - x x Geometry Correction, 4-Corner, Rotate x x x x Genlock (V-Lock) - - x x Pan, Zoom, Tilt x x x x Edge Blending x x x x Edge Blend Black Level Correction - x x x Auto pan/zoom/tilt of content for blending x x x x Projection Mapping/Warp x x x x

10 HQView530 Universal HQV Scaler Switcher-Scan Converter with Warp Mapping, Edge Blend & 3G-SDI In/Out and LCD display for fast easy set-up in the field. Harnessing the power of the Reon video processor running state of the art HQVTM algorithms with expertly designed hardware and firmware from Calibre, HQView530 is a universal image scaler and scan converter which provides stunning image quality for professional, broadcast and corporate AV users. HQView530 features 4-sided soft edge blend with multi-region black level correction for seamless blending of multiple projectors and includes flexible geometry correction functions able to correct image shape and projector misalignment by dragging and dropping each image corner, or pin/barrel, rotation or keystone and rotation. Full warp mapping is also supported by HQView530. A PC application is included for easy warp map creation or third-party generated warp maps can also be processed from automatic image alignment systems. HQView530 has 3G-SDI input and out connectivity with backwards compatibility with HDSDI and SD-SDI. For in-camera use a Genlock input is provided for compatible with bi or tri-level sync or black & burst. Best in class professional image processing in a compact affordable 1U format Front panel jog-wheel and LCD display for fast easy set-up in the field Use as a routing switcher and universal interface for 3G-SDI, HD-SDI, DVI or HDMI switching and distribution systems, projectors and displays Improve video image quality with better detail and clarity Superior de-interlacing reduces image flicker and artefacts Remove picture noise from poor quality video sources Powerful geometry correction for off-axis projection, pin/ barrel, image rotation 4-Sided soft edge blend for tiling multiple projectors to produce large images Flexible warp mapping for curved screen projection, simulation and 3D alignment Genlock and I/O Lock for in-camera and edge blend use 3G-SDI, HDMI, DVI, VGA Analog, Component YPbPr, RGsB/RGBS, Composite & S-Video inputs with signal compatibility up to 1080p & WUXGA 3G-SDI, HDMI/DVI & VGA Analog outputs Motion adaptive per pixel video de-interlacing, HD & SD Multi-directional diagonal de-interlace filter Automatic 3:2 & 2:2 pull-down detection with automatic film, video and video over film detection Chroma and Luma transient improvement Edge anti-aliasing 4-field full resolution SD & HD processing 4D Motion, Noise Adaptive HQV noise reduction for spatial and temporal noise Codec noise reduction for mosquito and block compression noise Direct input selection keys allow input selection without using menu system Flexible colour calibration controls Gamma controls 10-bit signal inputs, 12-bit accurate internal processing Selectable processing versus latency: best picture and low latency modes Latency as low as 0.25-frame progressive inputs, 1.25-frames interlaced inputs I/O Lock, Genlock/Frame Sync and Free Run selectable output modes Flicker filter for interlaced output modes USB port for in-field firmware updates TCP/IP remote control and Web Server Easy to navigate self-explanatory front panel menus Powerful geometry correction capabilities Pan, Zoom, Tilt Image rotation, pin/barrel correction 4-Sided edge blend with 48-bit processing & multi-region black level correction Flexible warp mapping

11 HQView530 Inputs 1 x HDMI with HDCP, 8/10/12 bit video compatible, 10-bit internal processing depth. Audio strip-off of SPDIF compatible formats. 1 x DVI with HDCP 1 x VGA Analog via 15HDD 1 x 3G-SDI, accepts 3G, HD and SD SDI signals via BNC supports 4:2:2 and 4:4:4 formats with audio de-embed 2 x Composite Video CVBS (NTSC, PAL & SECAM), 1 x via BNC jack and 1x via Cinch/RCA 1 x YC/S-Video via 4 pin mini DIN 1 x Component analog video YPbPr(S) or RGsB/RGBS via 3 or 4 x BNC jack Supported video formats: HD 720p, 1080i, 1080psf (psf digital only), 1080p23.97/24/25/30, 1080p30, 1080p50, 1080p59.94, 1080p60 ED 480p, 576p (not via SDI) SD 625i (576i), 525i (480i) Common VESA graphics formats from 640x480 to 1920x1200 (with reduced blanking for 1920x1200 and 1600x1200 modes) Multi standard support for CVBS & YC in PAL, NTSC, SECAM formats with selectable 3D comb for composite Outputs 1x 3G-SDI 1x DVI/HDMI with HDCP (HDMI with deep colour 8/10/12 bit support, via DVI connector) 1x VGA Analog via 15HDD 1x S/PDIF digital audio via RCA NB: 3G-SDI and VGA Analog outputs are disabled with HDCPencrypted input. Not all outputs are available simultaneously Supported Output formats: DVI/VGA common VESA formats 640x480 to 1920x1200, 720p, 1080p 3G-SDI in SMPTE formats 480i, 576i, 720p, 1080i, 1080p with selectable audio embed Selectable Genlock (V-Lock), I/O lock or frame rate conversion mode Selectable aspect ratio conversion Selectable vertical temporal filter for flicker reduction of interlaced outputs (edge blend not available in this mode) Note: PIP and edge blend are mutually exclusive so cannot be used simultaneously User Controls Front panel jog-wheel and LCD menu display for fast set-up. Keypad for direct input selection. Remote control via RS232, TCP/IP API and Web Server. PC-based Warp Map Generator tool USB port for uploading software updates and new features Power Requirements VAC, 35W typical Warranty 3-years return to base warranty covers parts and labour. HQView model > Front LCD menu or OSD control OSD OSD OSD LCD DVI/HDMI Inputs x x x x Component Input x x x x Composite/S-Video Inputs - - x x VGA Analog Input x x x x HD-SDI Input G-SDI Input - - x x DVI/HDMI Output x x x x VGA Analog Output - - x x 3G-SDI Output - - x x 3G-SDI Audio embed/de-embed - - x x HQV Processing x x x x PIP/POP/PAP - - x x TCP/IP Control x x x x Low Latency Mode x x x x Flicker Filter for Interlaced Output Modes - - x x Geometry Correction, 4-Corner, Rotate x x x x Genlock (V-Lock) - - x x Pan, Zoom, Tilt x x x x Edge Blending x x x x Edge Blend Black Level Correction - x x x Auto pan/zoom/tilt of content for blending x x x x Projection Mapping/Warp x x x x

12 HQView320/325/520/530 Automatic Geometric Alignment The HQView320/325/520/530 are Scalable Ready certified meaning that they can be used with Scalable Display Technologies products for automatic geometric alignment of displays. This software-driven, camera-based system automatically aligns displays with unsurpassed accuracy and speed, further simplifying the setup of blending and warping projects. Worldwide technical and commercial support Optoma Europe Optoma Europe Ltd. 42 Caxton Way The Watford Business Park Watford Hertfordshire WD18 8QZ UK Tel: +44 (0) Fax: +44 (0) Optoma Deutschland GmbH WIESENSTRASSE 21 D40549 Düsseldorf Germany Tel: +49 (0) Fax: +49 (0) Optoma France Batiment E avenue Edouard Vaillant Boulogne Billancourt France Tel. : +33 (0) Fax: +33 (0) Optoma Spain C/ José Hierro,36 Of. 1C Rivas VaciaMadrid Madrid Spain Tel: Fax: Optoma Benelux Optoma Benelux BV Randstad BW Almere The Netherlands T: +31 (0) F: + 31 (0) Local Representatives Turkey UAE Poland Russia Italy Optoma Scandinavia Optoma Scandinavia Lerpeveien 25 Postboks 9515 Åskollen 3038 Drammen Norway Tel: Fax: Optoma USA Optoma USA Headquarters 3178 Laurelview Ct. Fremont, CA Tel: (510) Fax: (510) Atlanta Sales Office 7000 Central Park NE, Suite 570, Atlanta, GA Tel: (678) Fax: (770) Canadian Sales Office 2420 Meadowpine Blvd, Suite 105, Mississauga, ON L5N 6S2, CANADA Tel: (905) Optoma Asia Taiwan Optoma Corporation Taipei Office 5F., No. 108, Minchiuan Rd., Shindian City, Taipei Taiwan 231, R.O.C. Tel:: Fax:: Taichung Office 7F-5, No.3, Lane 2, 1st Rd, Taichung Industrial Park, Xitun Dist., Taichung City, 40767, Taiwan, R.O.C. Tel:: Fax:: Kaohsiung Office Rm. D, 7F, No.108, Zhonghua 3rd Rd., Qianjin Dist., Kaohsiung City 80145, Taiwan, R.O.C. Tel:: Fax:: China Shanghai Office 5F, No Kaixuan Road, Changning District, Shanghai Tel: Fax: Beijing Office 20D apartment 3, Build No.3, Yindu Tower, No 48 ZhiChun road, HaiDian district, Beijing Tel: Fax: *8018 ShenYang Office Room1201, building C3, Wulihe Tower, No 4-1 WenTi road, HePing district, ShenYang Tel:: Fax:: Xi an Office Room 1310, building B, ShiMao tower, GuanDongZheng street, Xi an Tel: Fax: GungZhou Office Room 602, NanTie Tower, No.57 No.1ZhongShan road, YueXiu district, GungZhou Tel: / Fax: ChongQing Office Room 9-2, building 19 HuaYuMingDu, ShiQiaoPu, ChongQing Tel: Fax: ChengDu Office Room A3 floor 20, building A Time digital square, No.1 South RenMin road, ChengDu Tel: / Hong Kong Office Unit A, 27/F., Dragon Centre, 79 Wing Hong Street, Cheung Sha Wan, Kowloon, Hong Kong Tel:: Fax:: Copyright 2012, Optoma Europe Ltd. All other product names and company names used herein are for identification purposes only and may be trademarks or registered trademarks of their respective owners. DLP, BrilliantColor and the DLP logo are registered trademarks of Texas Instruments. Some images may be simulated. All images of products are for representation purposes only. Whilst every care is taken to provide accurate images of our products, actual products may differ slightly. Some product images may have been digitally altered by us to add an Optoma logo to the front panel. Optoma reserves the right to amend or alter actual product or product images without notice. All specifications are subject to change without notice. Errors and omissions excepted V2-31/10/12