Table of contents. Operating Instructions Home Theater Audio System. Step 1. Step 2. Step 3. Step 4. Model No. SC-HT17 SC-HT16 SC-HT15

Transcription

1 POWE PUT SEECTO %DIGITA H. BASS DOWN UP PHONES Operating Instructions Home Theater Audio System Model No. SC-HT Table of contents Dear customer Thank you for purchasing this product. Before connecting, operating or adjusting this product, please read the instructions completely. Please keep this manual for future reference. Before use IMPOT SAFET STUCTIONS... Supplied accessories... The remote control... is used in the illustrations unless otherwise mentioned. is only for the U.S.A. Step Speaker setup Step Home theater connections 8 Step Step Other connections 0 Settings Operations For Canada only: The word "Participant" is used in place of the word "Partner". Basic operations... Control guide... 6 The radio... 8 Other functions... 9 Making a recording... The ESET function... emote control operation guide... eference Specifications... istening caution... 6 Maintenance... 6 Product service... 6 Warranty (U.S.A.)... 7 Troubleshooting guide...back cover P PC PP QT799-P

2 IMPOT SAFET STUCTIONS ead these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. ) ead these instructions. ) Keep these instructions. 0) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Before use ) Heed all warnings. ) Follow all instructions. ) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. ) Only use attachments/accessories specified by the manufacturer. ) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. ) Unplug this apparatus during lightning storms or when unused for long periods of time. ) efer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. QT799 CAUTION ISK OF EECTIC SHOCK DO NOT OPEN CAUTION: TO EDUCE THE ISK OF EECTIC SHOCK, DO NOT EMOVE SCEWS. NO USE-SEVICEABE PATS SIDE. EFE SEVICG TO QUAIFIED SEVICE PESONNE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WANG: TO EDUCE THE ISK OF FIE, EECTIC SHOCK O PODUCT DAMAGE, DO NOT EXPOSE THIS APPAATUS TO A, MOISTUE, DIPPG O SPASHG AND THAT NO OBJECTS FIED WITH IQUIDS, SUCH AS VASES, SHA BE PACED ON THE APPAATUS. THE FOOWG APPIES ON THE U.S.A. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part of the FCC ules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: eorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ technician for help. Any unauthorized changes or modifications to this equipment would void the user s authority to operate this device. This device complies with Part of the FCC ules. Operation is subject to the following two conditions: () This device may not cause harmful interference, and () this device must accept any interference received, including interference that may cause undesired operation. The socket outlet shall be installed near the equipment and easily accessible or the mains plug or an appliance coupler shall remain readily operable.

3 %DIGITA UP PHONES Supplied accessories System SC-HT Please check and identify the supplied accessories. AC power supply cord System cable FM indoor antenna AM loop antenna (KCBCB00006) (KHAHA000) (SA0007-) Main unit SA-HT7 SA-HT6 SA-HT Front speakers SB-FS90 SB-FS880 SB-FS880 Surround speakers SB-FS880 SB-FS SB-FS Center speaker SB-PC90 SB-PC SB-PC Subwoofer SB-WA7 SB-WA6 SB-WA The remote control 6/6, AA, UM- Before use (NDAAAA0000) emote control transmitter Batteries (x ) Speaker cable(s) (EU77KK0) SC-HT (EU77KH0) (EE0A) ( m x ) SC-HT (EE0A) ( m x ) (EE0C) (0 m x ) ubber pads (KA007-KJ) Insert so the poles (+ and ) match those in the remote control. Do not use rechargeable type batteries. Use Aim at the sensor, avoiding obstacles, at a maximum range of 7 m ( feet) directly in front of the unit. POWE PUT SEECTO emote control signal sensor H. BASS DOWN Sticker sheet SC-HT 7 meters ( feet) Speaker stands (QCA09) Transmission window (QV0060) (x ) Speaker stands with long cables (QV0060A) (x ) Stand bases Screws (QV009-S) (XTN+FFN) (XTN+8FFN) (K7CXJCA0000) (x ) SC-HT (x ) (arge x 8) (Small x 8) SC-HT (XTN+FFN) (arge x ) (XTN+8FFN) (Small x ) Optical fiber cable Use the numbers indicated in parentheses when asking for replacement parts. (As of January 00) In U.S.A. to order accessories, refer to Accessory Purchases on page 7. Note Keep the transmission window and the unit s sensor free from dust. Operation can be affected by strong light sources, such as direct sunlight, and the glass doors on cabinets. Manufactured under license from Dolby aboratories. Dolby, Pro ogic and the double-d symbol are trademarks of Dolby aboratories. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. QT799

4 Step Speaker setup Supplied accessories Speaker stands with long cables Speaker stands (x ) (x ) SC-HT (x ) Stand bases (x ) SC-HT (x ) Front and surround speaker assembly Speaker setup Step To prevent damage or scratches, lay a soft cloth and perform assembly on it. For assembly, use a Phillips-head screwdriver. Attach the pipe to the base. Thread the speaker cable through the base. Untie the cable before threading. Secure the pipe to the base. Small screws (included) Insert the pipe. Ensure the screws are securely fastened by lightly tightening the left and right side screws alternately until fully tightened. Match the holes. The supplied stands are specially designed for use with this unit s speakers. Only use as indicated in this setup. Attach the stand to the speaker. Before attaching, check the speaker label. SB-FS90: Use as front speakers. Attach the stands with the short cables. SB-FS880: Use as surround speakers. Attach the stands with the long cables. arge screws (included) Speaker height Front Speakers Try to line up the middle of the speakers with the middle of the television. Surround speakers It is usually better to position the surround speakers a little higher. QT799 ou can also attach to the upper rear of the speaker. Ensure the stand is fastened on straight by lightly tightening the top and bottom screws alternately until fully tightened. There is no difference between the right and left speakers.

5 ch ch arge screws Small screws Speaker cable(s) Sticker sheet (x 8) (x 8) ( m x ) SC-HT (x ) SC-HT (x ) SC-HT ( m x ) (0 m x ) (x ) Connect the speaker cables. Copper Silver Connect the speaker cables. Press the speaker cable into the groove. Speaker setup Step Thread the excess cable. Fasten the speaker cable to the base. Slot Attach the stickers to the speaker cables. Front speaker () Front speaker () Surround speaker () Surround speaker () Center speaker Front and surround speakers Use the speakers with long cables for the surround speakers (SB-FS880). SC-HT Front speakers About 0 cm ( ) About 0 cm ( ) FONT FONT ch FONT Center speaker About 0 cm ( ) FONT ch Surround and center speakers Use the long speaker cables for the surround speakers (SB-FS). About 0 cm ( ) CENTE CENTE SUOUND ch SUOUND ch QT799

6 Speaker setup Supplied accessories ubber pads SC-HT Placement and connections of speakers 6QT799Speaker setup Step Front speaker () Place the speakers. e.g., Surround speaker () Center speaker Front speaker () Subwoofer Surround speaker () SC-HT Surround speakers Place on a shelf or rack. Place the front, center, and surround speakers at approximately the same distance from the seating position. The angles in the diagram are approximate. Front speakers (left, right) Place on the left and right of the at seated ear height so that there is good coherency between the picture and sound. Center speaker Place underneath or above the center of the. Aim the speaker at the seating area. Surround speakers (left, right) Place on the side of or slightly behind the seating area, higher than ear level. Subwoofer The subwoofer can be placed in any position as long as it is at a reasonable distance from the. Note that some experimentation can yield the smoothest low frequency performance. Placement near a corner can increase the apparent output level, but can result in unnatural bass. Preventing the speakers from falling over Attach screw eyes (not included) to secure the speakers to a wall (diagram on the right). Obtain the screws appropriate to the walls and pillars to which they are going to be fastened. Consult with a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support. Improper installation may result in damage to the wall or speakers. If irregular coloring occurs on your television The supplied speakers are designed to be used close to a television, but the picture may be affected with some televisions and setup combinations. If this occurs, turn the television off for about 0 minutes. The television's demagnetizing function should correct the problem. If it persists, move the speakers further away from the television. Caution Positioning for best effect How you set up your speakers can affect the bass and the sound field. Note the following points. Attach the included rubber pads to the base of the center speaker ( and SC-HT: center and surround speakers). This prevents vibration from causing the speakers to move or fall over. Use pads per speaker. Place speakers on flat secure bases. Placing speakers too close to floors, walls, and corners can result in excessive bass. Cover walls and windows with a thick curtain. Attaching the rubber pads Bottom of surround speaker ( and SC-HT) Bottom of center speaker ubber pads ubber pads Note Keep your speakers at least 0 mm (/") away from the system for proper ventilation. screw eyes (not included) Speaker Wall The main unit and supplied speakers are only to be used as indicated in this manual. Failure to do so may lead to damage to the receiver and/or the speakers, and may result in the risk or fire. Consult a qualified service person if damage has occurred or if you experience a sudden change in performance. Do not attempt to attach these speakers to walls using methods other than those described in this manual.

7 Connect the speaker cables to the subwoofer. Subwoofer FONT () FONT () Copper Silver Attaching to a wall 0 - mm (-/6 - -/8 ).0-.0 mm (/8 - / ) Copper Silver mm (9/6 - /8 ) 7-9 mm (9/ - / ) 6 Ω FONT 80 mm (7-/6 ) 7 mm (6-7/8 ) Wall or pillar Screw (not included) Ω SUOUND SC-HT Other speaker setup options Ω CENTE SUOUND () SUOUND () CENTE SC-HT Surround speakers The wall or pillar on which the speakers are to be attached should be capable of supporting 0 kg ( lb.) per screw. Consult a qualified building contractor when attaching the speakers to wall. Improper attachment may result in damage to the wall and speakers. When mounting the speakers to walls, use a string (not included) to prevent them from falling (è page 6). (: front and surround speakers, and SC-HT: front speakers) Use of optional speaker cables are recommended when mounting. (ou can also remove the speaker cables from the pipes supplied with this system.) Note Never short-circuit positive (+) and negative ( ) speaker wires. Fitting optional speaker stands SC-HT Surround speakers mm, Pitch 0.8 mm Plate thickness +7 to 0 mm (9/ - /6 ) 60 mm (-/6 ) Speaker stands (not included) Observe the diameter and length of the screws and the distance between screws as shown in the diagram. The stands must be able to support over 0 kg ( lb.). The stands must be stable even if the speakers are in a high position. QT799 Speaker setup Step 7

8 Step Home theater connections Other accessories Stereo connection cable (not included) eft ight Coaxial cable (not included) Video connection cable (not included) S-Video cable (not included) Turn off all components before making any connections. To connect equipment, refer to the appropriate operating instructions. Home theater connections Step player (Monitor) VIDEO S-VIDEO MONITO OUT DV / VC S-VIDEO OUT S-VIDEO S-VIDEO terminals Use this connection for better picture quality than with the VIDEO terminals. (Monitor) FM GND CENTE MONITO OUT PB P B P B S-VIDEO MONITO OUT DV / VC AM P P P GAME/AUX OUT FONT SUOUND SUBWOOFE OUT OUT () (DV) () DV / VC / 6CH DV / VC GAME/AUX MONITO DV OPT OPT COAXIA AUDIO VIDEO COMPONENT VIDEO DIGITA FONT (, ) SUOUND SUBWOOFE (, ) AUDIO OUT CENTE VIDEO OUT DIGITA AUDIO OUT QT799 Player 8

9 To SA-HT7 Supplied accessories System cable AC power supply cord (x ) (x ) Changing the digital input settings ou can change the input settings for the digital terminals if necessary. Note the equipment you have connected to the terminals, then change the settings (è page ). Note The included AC power supply cord is for use with this unit only. Do not use it with other equipment. Do not use an AC power supply cord from any other type of equipment with this unit. Use digital connection to enjoy Dolby Digital or DTS. Notes on digital input This unit can decode the following signals: Dolby Digital, DTS PCM, including PCM with sampling frequencies of 96 or 88. khz It cannot decode: Other digital signals, such as MPEG Dolby Digital F signals from a laser disc player FM AM player GAME/AUX GND OUT DV / VC AUDIO () (DV) () OPT OPT COAXIA DIGITA SC-HT Home theater connections Step FONT (, ) AUDIO OUT DIGITA AUDIO OUT VIDEO OUT Connect the video cable directly to the. VIDEO player (Monitor) Subwoofer and AC power supply cord Subwoofer Household AC outlet (AC 0 V/60 Hz) AC power supply cord (included) Connect this cord after all other cables are connected. SC-HT Conserving power The unit consumes a small amount of power even when it is turned off with [8, POWE]. To save power when the unit is not to be used for a long time, unplug it from the household AC outlet. ou will need to reset some memory items after plugging in the unit. To disconnect Press the catch and pull out. Catch 7 Ω FM O AN G AC ~ A System cable (included) TO SB-WA7 A EXT AM GAME/AUX T QT799 9

10 B B Step Other connections Other accessories Stereo connection cable (not included) eft ight Optical fiber cable (not included) Video connection cable (not included) S-Video cable (not included) recorder or VC COMPONENT VIDEO terminals This connection provides high quality pictures by separating the color (PB and P) and the luminance () signals. S-VIDEO terminals Use this connection for better picture quality than with the VIDEO terminals. P P B P B P P P PB COMPONENT VIDEO OUT S-VIDEO MONITO OUT DV / VC S-VIDEO OUT OUT MONITO DV COMPONENT VIDEO P Other connections Step TO SB-WA7 A 7 Ω EXT FM AM GAME/AUX GND P PB COMPONENT VIDEO CENTE MONITO OUT (Monitor) P B P B P P P OUT FONT SUOUND SUBWOOFE OUT OUT () (DV) () DV / VC / 6CH DV / VC GAME/AUX MONITO DV OPT OPT COAXIA AUDIO VIDEO COMPONENT VIDEO DIGITA P S-VIDEO S-VIDEO MONITO OUT DV / VC (Monitor) recorder or VC AUDIO OUT AUDIO VIDEO OUT VIDEO DIGITA AUDIO OUT recorder or VC SC-HT efer to the SC-HT SETUP GUIDE when connecting a DM-ES0 recorder. 7 Ω FM GND TO SB-WA AM A EXT GAME/AUX OUT DV / VC AUDIO () (DV) () OPT OPT COAXIA DIGITA recorder or VC AUDIO OUT AUDIO VIDEO OUT DIGITA AUDIO OUT QT799 0 VIDEO Connect the video cable directly to the. (Monitor)

11 B B Changing the digital input settings ou can change the input settings for the digital terminals if necessary. Note the equipment you have connected to the terminals, then change the settings (è page ). Note Use digital connection to enjoy Dolby Digital or DTS. Do not bend the optical fiber cable. (Input source) COMPONENT VIDEO terminals This connection provides high quality pictures by separating the color (PB and P) and the luminance () signals. S-VIDEO terminals Use this connection for better picture quality than with the VIDEO terminals. P P B P B P P P OUT MONITO DV COMPONENT VIDEO 7 Ω TO SB-WA7 EXT A FM AM GAME/AUX GND PB P P PB COMPONENT VIDEO OUT COMPONENT VIDEO CENTE MONITO OUT P B P B P P P OUT FONT SUOUND SUBWOOFE OUT OUT () (DV) () DV / VC / 6CH DV / VC GAME/AUX MONITO DV OPT OPT COAXIA AUDIO VIDEO COMPONENT VIDEO DIGITA P S-VIDEO MONITO OUT DV / VC S-VIDEO MONITO OUT DV / VC S-VIDEO OUT S-VIDEO Other connections Step AUDIO OUT VIDEO OUT VIDEO DIGITA AUDIO OUT (Input source) QT799 SC-HT 7 Ω 7 Ω FM FM GND GND TO SB-WA TO SB-WA A A EXT EXT AM AM GAME/AUX GAME/AUX OUT OUT DV / VC AUDIO DV / VC AUDIO () (DV) () OPT OPT COAXIA () (DV) () DIGITA OPT OPT COAXIA DIGITA AUDIO AUDIO OUT OUT DIGITA AUDIO DIGITA OUT AUDIO OUT

12 B Other connections Supplied accessories FM indoor antenna AM loop antenna (x ) (x ) Other accessories Stereo connection cable (not included) eft ight Video connection cable (not included) Antennas FM indoor antenna (included) Adhesive tape Fix the end of the antenna where reception is best. For best reception FM outdoor antenna (not included) Disconnect the FM indoor antenna. The antenna should be installed by a competent technician. Other connections Step TO SB-WA7 A 7 Ω EXT FM AM GND ed White GAME/AUX GND AM loop antenna (included) Black OUT DV / VC AUDIO Click! FONT SUOUND SUBWOOFE / 6CH FM outdoor antenna CENTE MONITO OUT P B P B P P P 7 Ω FM OUT OUT DV / VC GAME/AUX MONITO DV VIDEO COMPONENT VIDE 7 Ω coaxial cable PB EXT Antenna plug AM Keep the antenna cord away from players and other cords. Game machine or other AV equipment SC-HT 7 Ω FM GND CENTE MONITO OUT P P B P B FM GND -WA7 AM P P P AM A EXT GAME/AUX OUT DV / VC AUDIO FONT SUOUND SUBWOOFE / 6CH OUT OUT DV / VC GAME/AUX MONITO DV VIDEO COMPONENT VIDEO GAME/AUX OUT DV / VC AUDIO () (DV) OPT OPT DIGITA QT799 AUDIO OUT VIDEO OUT AUDIO OUT VIDEO OUT Connect the video cable directly to the. VIDEO Game machine Game machine (Monitor)

13 Step Settings Change the settings to suit your equipment to the environment in which you are using it. Before making any changes, read the descriptions of the settings, note the factory settings and ranges, and refer to the equipment s instructions. DISTANCE è See below D-PUT è See below D COMP è See page 0 A/D ATT è See page 0 POWE PUT SEECTO Switch on. %DIGITA POWE PUT SEECTO H. BASS DOWN UP PHONES DISTANCE D-PUT (digital input) Enter the distance of the front, center and surround speakers from the seating position. The factory settings are: FONT: CENTE: SUOUND: Enter the setup mode. Press at the same time. 0 FEET 0 FEET FEET SETUP Change the setting for the DIGITA terminals (OPT, OPT, COAXIA) on the rear of the unit if the equipment you have connected is different to that labeled. The factory settings are: : DV: : Enter the setup mode. Press at the same time. OPT OPT COAX SETUP Step Select DISTANCE. PUT SEECTO DISTANCE DISTANCE D COMP D-PUT A/D ATT Select D-PUT. PUT SEECTO D-PUT DISTANCE D COMP D-PUT A/D ATT Settings Select the speaker. FONT FONT CENTE SUOUND Select the input position. DV Change the setting. O epeat steps and 0 FEET FEET 0 FEET Change the setting. O epeat steps and OPT OPT OPT COAX Exit the setup mode. COMPETE Exit the setup mode. COMPETE Press at the same time. Press at the same time. Note ou can allocate only one piece of equipment per terminal. So for example if you change from OPT to OPT, DV will automatically switch to OPT. QT799

14 Settings Adjusting speaker output level ECEIVE DIVE SEECT AV SSTEM ECODE PAE ANAOG 6CH VC - / -BAND CH DIECT TUNG ENTE DISC 0 > = 0 SKIP SOW/SEACH u i t y STOP PAUSE PA g h q DIECT NAVIGATO FUNCTIONS TOP ENTE SUB / PA IST ETUN VO VO EC EC EC MODE /VIDEO MUTG PUT MODE SUBWOOFE - H.BASS/ -C.FOCUS -EVE/ -TEST TONE/ BAANCE EFFECT / / OFF SFC MUSIC AV/MOVIE Settings Step -EVE/ -TEST Press and hold Output the signal. Adjust the main volume. -EVE/ -TEST Select the speaker channel. / / Adjust the level. epeat steps and -EVE/ -TEST Press and hold Stop the test signal. QT799 C (center), S (right surround) and S (left surround) can be adjusted between 0 db and +0 db, with 0 db being the level of the front speakers. Adjust center and surround output to the same apparent level of the front speakers. For SW (subwoofer), you can select so there is no output, M for minimum output, a level between and 9, or MAX for maximum output. Adjust subwoofer output so it is balanced with the front speakers. Subwoofer output is easily influenced by the source. ou can also change its level while playing something for better effect (è page 9).

15 Basic operations ENTE SUB / PA IST ETUN POWE PUT SEECTO %DIGITA H. BASS DOWN UP VO VO EC EC EC MODE /VIDEO MUTG PHONES PUT MODE SUBWOOFE - H.BASS/ -C.FOCUS -EVE/ -TEST POWE Switch on. GAME/AUX PUT SEECTO Select input. DV/VC Start play of the source. The unit sets the sound mode to suit the input signal. DOWN Adjust the volume. UP TONE/ BAANCE OFF OFF EFFECT / / SFC MUSIC AV/MOVIE SFC MUSIC AV/MOVIE () When playing video sources connected to The picture remains on the screen even if you select. Adding surround effects to stereo sources Using Dolby Pro ogicii Dolby Pro ogicii processor works not only on sources recorded with Dolby Surround, but also on any stereo source. Press to select a mode from the table at right. To cancel, press [OFF]. ou can make fine surround settings when in the MUSIC or PANOAMA mode. (è page ) MOVIE Use this mode when playing movie software, especially videotapes, recorded in Dolby Surround. MUSIC Adds surround effects to stereo sources. PANOAMA Sound is spread out more so you feel like you are surrounded by music. Using the Sound Field Control (SFC) Enjoy an enhanced sound experience with greater presence and spread by using these SFC modes with PCM or analog stereo sources. SFC MUSIC AV/MOVIE Press to select a mode from the tables at right. To cancel, press [OFF]. ou can adjust SFC effects. (è page ) MUSIC IVE Brings you up close for live stage performance and smoother vocals. POP/OCK For pop, rock, and other music that has a punch to it. VOCA For adding gloss to vocals. JAZZ Conveys the exciting and intimate atmosphere of a jazz club. DANCE For dance music and other sounds with a strong beat. PAT This mode uses the front and surround speakers so that sound is in stereo regardless of the direction you are facing. Operations Note Dolby Pro ogicii and SFC modes remain in effect until you turn the mode off. When input is PCM with sampling frequencies of 96 or 88. khz, you cannot add surround effects with Dolby Pro ogicii or SFC. When input is Dolby Digital or DTS, you cannot use SFC. AV/MOVIE DAMA For dramas and other material where dialog is important. ACTION For action movies and other material where impact is important. SPOTS To make you feel like you were in the stadium. MUSICA For musicals and other material where music is important. GAME Enjoy gaming with more impact. MONO For monaural sound. QT799

16 Control guide Main unit Standby indicator [] When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. [8, POWE] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. [% DIGITA, % P II, dts] ights to indicate the source s input signal and decoding format used. % DIGITA: Dolby Digital sources % P II: Dolby Pro ogicii decoder is being used dts: DTS sources [H.BASS] For enhancing the bass sound. The indicator lights when the feature is on. [] Volume control. %DIGITA POWE PUT SEECTO H. BASS DOWN UP PHONES emote control signal sensor [PUT SEECTO] For selecting input. The display changes as follows: GAME/AUX DV/VC [ ] For tuning the radio and presetting channels. [] For entering various settings. Press and hold to exit the mode. [PHONES] Headphone jack Plug type:. mm (/8") stereo Sound does not come from the speakers if you connect headphones. Avoid listening for prolonged periods of time to prevent hearing damage. Display Operations [DIGITA PUT] Program format indicators Show the channels contained in the digital input signal. They do not light when input is analog. : Front left channel C: Center channel : Front right channel S: Surround left channel S: If the surround channel is monaural. S: Surround right channel FE (ow Frequency Effects): Deep-bass effect. [D, ST, MONO] adio indicators D: A station is tuned. ST: A stereo FM broadcast is tuned. MONO: ou have switched to monaural mode to improve reception. [SEEP] Sleep timer indicator. [M] Flashes or lights during presetting. DIGITA PUT C S S S FE C.FOCUS CH MIX SFC D ST MONO SEEP M khz MHz 00Hz 0kHz QT799 6 [C.FOCUS, CH MIX, SFC] C.FOCUS: Appears when you are using Center Focus CH MIX: Appears when you are listening to a multi-channel source with headphones SFC: Appears when you are using an SFC mode General display Shows the input mode, radio frequency and other general information. [khz, MHz] Frequency unit indicators khz: AM, or PCM sampling frequency MHz: FM Spectrum analyzer display

17 emote control and Subwoofer This page describes the buttons used to control this unit. See the guide starting page for the buttons that control other units. [, ECEIVE] Standby/on button. [,,,,, 6, 7, 8, 9, 0] To enter radio frequencies and channels. [ 0, ENTE] To enter two digit channels. [DISC, DIECT TUNG] To enable selection of radio stations by frequency. [, CH, ] For selecting preset radio channels. [SUBWOOFE] For selecting subwoofer level. [-H.BASS/ C.FOCUS] For enhancing the bass sound. Press and hold to select center focus mode. [PUT MODE] For selecting AUTO, ANAOG or DIGITA. [TONE/BAANCE] To adjust the bass, treble and front speaker balance. [OFF] To cancel surround effect. [% P II] For selecting a Dolby Pro ogicii mode: MOVIE, MUSIC or PANOAMA. [MUSIC] For selecting SFC modes: IVE, POP/ OCK, VOCA, JAZZ, DANCE or PAT. [AV/MOVIE] For selecting SFC modes: DAMA, ACTION, SPOTS, MUSICA, GAME or MONO. ECEIVE DIVE SEECT 6 7 DIECT TUNG DISC DIECT NAVIGATO TOP SUB / PA IST PUT MODE SUBWOOFE TONE/ BAANCE SKIP u i g AV SSTEM EFFECT h ENTE > = 0 CH q FUNCTIONS ETUN VO VO EC EC EC MODE /VIDEO MUTG ENTE SOW/SEACH t y STOP PAUSE PA OFF PAE ANAOG 6CH ECODE VC - H.BASS/ -C.FOCUS - / -BAND -EVE/ -TEST / / SFC MUSIC AV/MOVIE [ PAE, ANAOG 6CH] [] [ ECODE] [VC] SC-HT [ PAE] [] [ ECODE] [VC] Input mode and remote control mode buttons. [ PAE, ANAOG 6CH] () Press and hold and input switches between 6-channel and -channel. [-/ BAND] For selecting. After selecting, press and hold to switch between FM and AM. [+,, ] To adjust the volume. [MUTG] To mute the volume. [-EVE/ TEST] Use when adjusting speaker level. Press and hold to start the speaker test signal. [EFFECT] Use when adjusting Dolby Pro ogicii or SFC effects. [ /, +/] First select EFFECT, EVE, TONE or BAANCE, then press [ /] or [+/] to adjust. Operations [AC ] This indicator lights when the unit is connected to the AC power supply. () When ANAOG 6CH input is selected: Set your player speaker output to "small", provided it has a speaker output setting function. QT799 7

18 The radio DIECT TUNG DISC 0 ENTE > = 0 CH ECEIVE DIVE SEECT DIECT TUNG ENTE DISC 0 > = 0 u g DIECT NAVIGATO TOP SKIP AV SSTEM ECODE i h PAE ANAOG 6CH VC CH SOW/SEACH t - / -BAND y STOP PAUSE PA q FUNCTIONS POWE PUT SEECTO %DIGITA H. BASS DOWN - / - / -BAND -BAND UP PHONES ENTE Press and hold SUB / PA IST VO EC EC EC MODE PUT MODE SUBWOOFE /VIDEO - H.BASS/ -C.FOCUS ETUN VO MUTG -EVE/ -TEST Select. Select FM or AM. Select the frequency. Auto tuning starts if you press and hold the button. TONE/ Direct tuning Input the frequency of the station. emote control. Press [-/ BAND] to select..press and hold [-/ BAND] to select FM or AM.. Press [DISC, DIECT TUNG]..Press the numbered buttons to enter the frequency. e.g. To select 07.9 MHz, press [] [0] [7] [9] If you do not press a button while the cursor is flashing, the display returns to the frequency being received. If the frequency has not been input correctly, EO will be displayed. Automatic presetting Manual presetting Preset the stations one at a time. Preparation: Tune to the station you want to preset. Main unit. Press [] to select MEMO..Press [ or ] to select the channel.. Press [] to store. To cancel Press and hold []. For your reference FM stations can also be preset in the MONO mode. Selecting channels Operations The FM stations the unit can receive are preset in channels to 0. The AM stations the unit can receive are preset in channels to 0. (FM stations are replaced if any were preset in these channels.) Preparation: Select FM or AM. Main unit. Press [] to select MEMO..Press and hold [ ]. The tuner presets all the stations it can receive into the channels in ascending order. If you press and hold [ ], it starts from the current frequency. During automatic presetting, the memory indicator (M) flashes and the frequency scrolls. The memory indicator and channel numbers are displayed for a second when a station is preset. The last station to be preset is displayed when presetting finishes. To cancel Press and hold []. emote control Press [, CH, ]. or Press the numbered buttons. For channels to 9, press the corresponding number. For channels 0 or over, press [ 0, ENTE], then the two digits. e.g. To select channel : [ 0, ENTE] [] [] FM mode ou can improve FM reception by switching reception to monaural. Main unit.press [] to select FM MODE..Press [ or ] to select MONO. Select AUTO to cancel.. Press []. MONO lights. QT799 8 To switch between FM and AM on the main unit. Press [] to select BAND.. Press [ or ] to select FM or AM.. Press [].

19 Other functions DIECT TUNG ENTE DISC 0 > = 0 u g SKIP i h SOW/SEACH t y STOP PAUSE PA q DIECT NAVIGATO FUNCTIONS TOP H. BASS SUBWOOFE ENTE MUTG SUB / PA IST ETUN PUT MODE VO EC EC EC MODE PUT MODE SUBWOOFE /VIDEO - H.BASS/ -C.FOCUS VO MUTG -EVE/ -TEST - H.BASS/ -C.FOCUS TONE/ BAANCE EFFECT / / OFF SFC MUSIC AV/MOVIE POWE PUT SEECTO %DIGITA H. BASS DOWN UP PHONES TONE/ BAANCE / / Input mode H.Bass This unit automatically detects whether input is digital or analog, but you can fix the input mode. emote control Press [PUT MODE] to select "AUTO", "ANAOG" or "DIGITA". Tone ou can adjust the level of the bass and treble. emote control.press [TONE/BAANCE] to select BASS or TEBE.. Press [ /] or [+/] to adjust bass/treble. Note Input signals must be either analog or PCM, and Dolby Pro ogicii and SFC must be off. () ou cannot adjust the tone if ANAOG 6CH is selected. Balance ou can adjust the balance of the front speakers. emote control. Press [TONE/BAANCE] to select BAANCE..Press [ /] or [+/] to adjust. Subwoofer level emote control Press [SUBWOOFE]. Adjust the level in steps: SW M, SW, SW 0, SW, and SW MAX. Select SW to stop output. Note Sound can be distorted if you raise the volume while subwoofer level is high. educe subwoofer level if this occurs. () ou cannot adjust the subwoofer level if ANAOG 6CH is selected. ou can enhance low-frequency sound so that heavy bass sound can be heard clearly, even if the acoustics of your room are not optimal. emote control Press [-H.BASS/ C.FOCUS]. Main unit Press [H.BASS]. The indicator lights. To cancel Press [-H.BASS/ C.FOCUS] or [H.BASS] again. Note ou cannot use H.Bass when you are using headphones. Actual effect depends on the disc. Center focus (Disc where the dialogue is recorded in the center channel) ou can make the sound of the center speaker seem like it is coming from within the television. emote control Press and hold [-H.BASS/ C.FOCUS]. C.FOCUS lights. The factory setting is off. The center focus cannot be used in the following cases: When input signal is PCM or analog stereo. () When ANAOG 6CH is selected. Muting emote control Press [MUTG]. To cancel Press [MUTG] again. Muting is also canceled when the unit is turned off. Operations QT799 9

20 Other functions TOP PUT SEECTO PUT MODE SUB / PA IST ENTE ETUN VO VO EC EC EC MODE /VIDEO MUTG PUT MODE SUBWOOFE - H.BASS/ -C.FOCUS -EVE/ -TEST TONE/ BAANCE EFFECT / / OFF SFC MUSIC AV/MOVIE %DIGITA POWE PUT SEECTO H. BASS DOWN UP PHONES A/D attenuator Sleep timer Operations QT799 Turn the A/D attenuator on if OVEFOW lights frequently when using -channel analog input. Main unit.press [ and ] at the same time to enter the setup mode.. Press [PUT SEECTO] to select A/D ATT..Press [ or ] to select ON or OFF..Press [ and ] at the same time to exit the setup mode. Dynamic range compression Change this setting to listen to software recorded with Dolby Digital at low volume (such as late at night) and maintain audio clarity. It reduces the peak level in loud scenes without affecting the sound field. Main unit.press [ and ] at the same time to enter the setup mode.. Press [PUT SEECTO] to select D COMP..Press [ or ] to select OFF, STANDAD or MAX..Press [ and ] at the same time to exit the setup mode. OFF: The software is played with the original dynamic range (factory setting). STANDAD: The level recommended by the producer of the software for household viewing. MAX: The maximum allowable compression (recommended for night viewing). Dimmer Dim the display for better viewing in a darkened room. Main unit. Press [] to select DIMME..Press [ or ] to select OFF or ON.. Press []. The SEEP timer can turn the unit off after a set time. It does not control any other components. Main unit. Press [] to select SEEP..Press [ or ] to select the desired time. The display changes as follows: OFF v SEEP 0 v SEEP 60 v SEEP 90 v SEEP 0 (minutes). Press []. The display dims even when the dimmer is OFF. To check the setting. Press [] to select SEEP.. Press [ or ] once. The time remaining appears.. Press []. To change a setting epeat the procedure from the beginning. PCM/DTS fix mode In rare cases, the unit may have trouble recognizing the digital signals on discs. With the PCM signals on CDs, this may cause the beginning of a track to be cut off. Engage the PCM FIX mode if this occurs. With DTS, the signals may not be recognized at all. Engage the DTS FIX mode if this occurs. While the input source is selected: emote control.press [PUT MODE] to select DIGITA.Press and hold [PUT MODE] for four seconds. The current mode is displayed. Press again to change the mode. Each time you press the button: AUTO PCM FIX DTS FIX When a FIX mode is on, the unit cannot process other signals. This may cause noise to be output. Select AUTO if this occurs. The mode returns to AUTO when you switch the unit to standby. For your reference If you are playing a DTS CD that contains both DTS and PCM, but it isn t playing properly, then do the following after step above: On the Main unit. Press [] to select DTS-PCM.. Press [ or ] to select ON.. Press []. If this causes noise to occur, return the setting to OFF. (This setting is effective for each digital source.) 0

21 Other functions Making a recording TOP SUB / PA IST ENTE ETUN PUT SEECTO EFFECT VO EC EC EC MODE PUT MODE TONE/ BAANCE SUBWOOFE EFFECT /VIDEO - H.BASS/ -C.FOCUS VO MUTG -EVE/ -TEST / / -EVE/ -TEST OFF SFC MUSIC AV/MOVIE / / POWE PUT SEECTO %DIGITA H. BASS Center Width Control "C-WDTH" ou can adjust the effect of MUSIC and PANOAMA with the center width control. This adjustment helps you realize a more natural sound image when listening to music. Move sound out into the front speakers to improve the overall front image, or add sound to the center speaker to fix the center image. ou can choose a level between 0 (the center speaker is dominant) and 7 (center sound is spread out). The default level is. emote control. Press [EFFECT] to select C-WDTH..Press [ /] or [+/] to adjust the effect. Dimension Control "DIMEN" ou can adjust the effect of MUSIC and PANOAMA with the dimension control. ou can make up for differences in the output level of the front and surround speakers. ou can choose a level between and + Increase the level to move sound to the front speakers, decrease to move it to the surround speakers. The default is level 0. emote control. Press [EFFECT] to select DIMEN..Press [ /] or [+/] to adjust the effect. ecording on other equipment ou can record to a unit connected to DV/VC OUT. ou can record any analog source except DV/VC..Press [PUT SEECTO] to select the source to be recorded.. Begin recording. Follow your recording unit s operating instructions..start the source to be recorded. Note () When you select ANAOG 6CH mode, only sound from the front left and right channels is recorded. This unit cannot record digital sources. Connect through the analog terminals and select "ANAOG" input. The ESET function Adjusting SFC effects ou can adjust the sound field by adjusting the level of the speakers and the delay time of the surround speakers. These adjustments can be made for each SFC mode. To adjust the speaker level emote control.press [-EVE/ TEST] to select the speaker channel. Each time you press the button: C S S SW.Press [ /] or [+/] to adjust the level. C, S, and S: 0 db to +0 db SW: (off) M 9 MAX To adjust the delay time emote control. Press [EFFECT].. Press [ /] or [+/] to change the delay time. The default is 0 msec. (0 msec 00 msec) POWE PUT SEECTO The operation settings for the unit will be initialized to the settings made at the time of shipment. However, any preset radio stations will not be erased. %DIGITA. Press [] to select ESET..Press [ or ] to select ES. To cancel, select NO..Press []. H. BASS Operations QT799

22 emote control operation guide This remote control can operate Panasonic and Technics audiovisual components that have remote control sensors. ou may need to change the remote control code. (è page ) Note that this remote control cannot operate some equipment and that it may not be able to perform some operations. ECEIVE DIVE SEECT AV SSTEM PAE ANAOG 6CH ECODE VC - / -BAND Watching s Switch on AV SSTEM Switch on the television and select input /VIDEO DIECT TUNG DISC 0 ENTE > = 0 CH SKIP SOW/SEACH u i t y STOP PAUSE PA g h q DIECT NAVIGATO FUNCTIONS Switch off SC-HT PAE SC-HT PAE PAE ANAOG 6CH PAE ANAOG 6CH ECODE ECODE Switch on the player and start play or or AV SSTEM AV SSTEM PA q AV SSTEM TOP Operating the player/ recorder SUB / PA IST ENTE ETUN DIECT NAVIGATO 6 VO VO EC EC EC MODE /VIDEO MUTG PUT MODE SUBWOOFE TONE/ BAANCE EFFECT - H.BASS/ -C.FOCUS -EVE/ -TEST / / TOP Show disc menus SUB / PA IST ENTE > = 0 Start play from a selected item OFF SFC MUSIC AV/MOVIE VO Show disc menus ENTE SKIP u i Skip items during play FUNCTIONS Select and enter menu items SOW/SEACH t y Search through the disc Operations DIVE SEECT Switch between and HDD [ recorder with HDD] When you cannot switch to the disc or hard disk drive, after performing the following operations, press the button again.. While pressing [ENTE], press and hold [8] or [9] for approximately seconds.. Press [ ECODE]. The factory setting is [9]. EC MODE Select a recording mode Show player menus ETUN VO DIECT TUNG DISC Clear menus or return to previous menus EC Specify a disc [-disc changer] Start recording (Press and hold) PAUSE h Start slow-motion play PAUSE h To view frame-by-frame STOP g Stop play SOW/SEACH t y PAUSE h Pause play QT799 When using a Panasonic recorder Change the unit s remote control code to match the remote control code of the recorder. Preparations: Check the remote control code of the recorder. For about one second hold down both [ENTE] and the button ([], [] or []) which the same number as the remote control code set by the recorder. The factory setting is [].

23 /VC Watching ECEIVE DIVE SEECT AV SSTEM PAE ANAOG 6CH ECODE VC - / -BAND Switch on AV SSTEM /VIDEO DIECT TUNG DISC 0 ENTE > = 0 CH SKIP SOW/SEACH u i t y STOP PAUSE PA g h q DIECT NAVIGATO FUNCTIONS Switch off Switch on the television and select input AV SSTEM TOP SUB / PA IST PUT MODE SUBWOOFE TONE/ BAANCE EFFECT ENTE ETUN VO VO EC EC EC MODE /VIDEO MUTG - H.BASS/ -C.FOCUS -EVE/ -TEST / / Operating the CH Change channels sequentially ENTE > = 0 Select channels directly SUB / PA IST VO ETUN VO Adjust the volume OFF SFC MUSIC AV/MOVIE Watching videotapes Switch on AV SSTEM /VIDEO Switch on the television and select input Switch off VC VC AV SSTEM AV SSTEM Switch on the player and start play PA q AV SSTEM Operations Operating the video deck CH Change channels sequentially ENTE > = 0 Select channels directly SOW/SEACH t y ewind or fast-forward STOP g Stop play PAUSE h Pause play QT799

24 emote control operation guide Using this remote control to operate equipment manufactured by Panasonic, Technics, and other companies It can also operate some other brands of televisions, video cassette players, and players. Check the table for the brand and enter the code as follows. ECEIVE DIVE SEECT 6 7 DIECT TUNG DISC DIECT NAVIGATO TOP SKIP u i g AV SSTEM PAE ANAOG 6CH ECODE VC ENTE h > = 0 - / -BAND CH SOW/SEACH t y STOP PAUSE PA q FUNCTIONS Changing the codes VC player VC SC-HT PAE PAE ANAOG 6CH Press and hold the button corresponding to the equipment The remote control outputs the on/off signal. If the code is correct, the equipment turns on or off. If it doesn t, try entering another code. e-enter the codes after you change the batteries Enter the first digit Enter the second digit SUB / PA IST PUT MODE SUBWOOFE TONE/ BAANCE EFFECT ENTE ETUN VO VO EC EC EC MODE /VIDEO MUTG - H.BASS/ -C.FOCUS -EVE/ -TEST / / Code table VC player PANASONIC 0,0,6 0,0,09, 0,0 AIWA APEX 0,,6 BOSE 9 VC OITON PHICO 06,07 0,09,,0 PIONEE 0,0, player PHIIPS 06 0,09, 0,6 OFF SFC MUSIC AV/MOVIE DENON 0,7 POKAUDIO 6 FEGUSON 0 QUASA 0 0,0,09, FISHE,,,8, AITE FUNAI 08,0 8 G.E. 0,0,07,09 0,0, GODSTA 07, 7 CA 0,07,09,,, 0,0,0,09 0,,,,6 0 SABA 0 GO-VIDEO SAMPO Operations HAMAN KADON HITACHI 0,07 09,0, JVC 9,,,8 9,0 09 SAMSUNG 0 SANO,8, SHAP 08, 6,7 08 SHTOM KENWOOD,9 SIVANIA 8 KH SMC KONIKA 9 KOSS SON 0 0,06,07, 6,7 0,6,7 8 XI 0,06,07,0, 0,,, 8,7,0 SVANIA 06,07, 0,09,,0 SMPHONIC 7 0 MAGNAVOX 06,07,,, 0,09, TECHNICS 0 MTEK 8 THOMSON 0 MITSUBISHI 07,,6,,,8,9 06 TOSHIBA 0,, 0 NEC 07, 9,,,8 VENTUE QT799 NEXTBASE 7 NODMENDE 0 ONKO, VIATA AMAHA 0,,0 ZENITH 8,0 0 07,

25 Specifications (IHF 78) n AMPIFIE SECTION MS output power of each channel driven 0 % total harmonic distortion khz front CH [] 70 W per channel (6 Ω) [] [SC-HT] 70 W per channel ( Ω) khz surround CH 70 W per channel ( Ω) khz center CH 60 W per channel ( Ω) 00 Hz subwoofer CH 60 W per channel ( Ω) Total MS output power [] 000 W [] [SC-HT] 800 W ated minimum sine wave MS power output % total harmonic distortion (Dolby Digital mode) 0 Hz-0kHz front CH [] 00 W per channel (6 Ω) [] [SC-HT] W per channel ( Ω) 0 Hz-0 khz surround CH W per channel ( Ω) 0 Hz-0 khz center CH 0 W per channel ( Ω) Hz-0 Hz subwoofer CH 0 W per channel ( Ω) Total FTC output power [] 80 W [] [SC-HT] 70 W ated minimum sine wave MS power output % total harmonic distortion (Stereo mode) 0 Hz-0 khz front CH [] 90 W per channel (6 Ω) [] [SC-HT] W per channel ( Ω) -0 Hz subwoofer CH 0 W per channel ( Ω) Total FTC output power [] 0 W [] [SC-HT] 0 W Total harmonic distortion Half power at khz (Front CH) [] 0. % (6 Ω) [] [SC-HT] 0. % ( Ω) Input sensitivity, DV/VC,, GAME/AUX S/N (IHF A), DV/VC,, GAME/AUX Input impedance, DV/VC,, GAME/AUX Tone controls BASS TEBE n VIDEO SECTION () Output voltage at V input (unbalanced) Maximum input voltage Input/output impedance 00 mv, IHF 66 7 db (8 db, IHF 66) 7 kω 0 Hz, +0 to -0 db 0 khz, +0 to -0 db Digital input OPTICA COAXIA ±0. Vp-p. Vp-p 7 Ω n FM SECTION Frequency range MHz Sensitivity. dbf ( µv, IHF '8) 0 db quieting sensitivity MONO 8. dbf (. µv, IHF '8) STEEO 8. dbf ( µv, IHF '8) Total harmonic distortion MONO 0. % STEEO 0. % S/N MONO 7 db STEEO 6 db Frequency response 0 Hz- khz, + db, - db Image rejection at 98 MHz 0 db Stereo separation khz 0 db Antenna terminal 7 Ω (unbalanced) n AM SECTION Frequency range 0-70 khz Sensitivity 0 µv/m Selectivity 0 db n SPEAKE SECTION Front speaker (:SB-FS90) (:SB-FS880) (SC-HT:SB-FS880) Type [] Way, Speakers, Bass-ref. [] [SC-HT] Way, Speaker, Bass-ref. Speaker unit Full range [] 8 cm (-/8 ) cone type x, 6 Ω [] [SC-HT] 8 cm (-/8 ) cone type, Ω Super tweeter [] 6 cm (-/8 ) ing Shaped Dome type, 6 Ω [] [SC-HT] 6 cm (-/8 ) ing Shaped Dome type, Ω Input power (IEC) [] 70 W (Max) [] [SC-HT] 70 W (Max) Output sound pressure level [] 8 db/w (.0 m) [] [SC-HT] 8 db/w (.0 m) Crossover frequency 7 khz Frequency range Dimensions (W x H x D) Mass [] 7 Hz-0 khz (-6 db) 90 Hz- khz (-0 db) [] [SC-HT] 78 Hz-0 khz (-6 db) 90 Hz- khz (-0 db) 60 x 7 or x 69 mm (0-/'' x 6-/8'' or 8-9/6'' x 0-9/6'') []. kg (9.6 lb.) [] [SC-HT].9 kg (8.6 lb.) Surround speaker (:SB-FS880) (:SB-FS) (SC-HT:SB-FS) Type Way, Speaker, Bass-ref. Speaker unit Full range 8 cm (-/8 ) cone type, Ω [] Super tweeter 6 cm (-/8 ) ing Shaped Dome type, Ω [] [SC-HT] Tweeter Piezo type, Ω Input power (IEC) 70 W (Max) Output sound pressure level [] 8 db/w (.0 m) [] [SC-HT] 80 db/w (.0 m) Crossover frequency [] 7 khz [] [SC-HT] khz Frequency range [] 78 Hz-0 khz (-6 db) 90 Hz- khz (-0 db) [] [SC-HT] 8 Hz-0 khz (-6 db) 9 Hz-7 khz (-0 db) Dimensions (W x H x D) Mass [] 60 x 7 or x 69 mm (0-/'' x 6-/8'' or 8-9/6'' x 0-9/6'') [] [SC-HT] 00 x x mm (-/6'' x -/'' x -/8'') [].9 kg (8.6 lb.) [] [SC-HT] 0.9 kg (. lb.) Center speaker (:SB-PC90) (:SB-PC) (SC-HT:SB-PC) Type Way, Speakers, Bass-ref. Speaker unit Full range 6. cm (-/ ) cone type x, Ω [] Super tweeter 6 cm (-/8 ) ing Shaped Dome type, Ω [] [SC-HT] Tweeter 6 cm (-/8 ) cone type, Ω Input power (IEC) 60 W (Max) Output sound pressure level 8 db/w (.0 m) Crossover frequency khz Frequency range [] 0 Hz-0 khz (-6 db) 0 Hz- khz (-0 db) [] [SC-HT] 0 Hz- khz (-6 db) 0 Hz- khz (-0 db) Dimensions (W x H x D)0 x 8 x 9. mm (- /8'' x -/6'' x -/'') Mass. kg (. lb.) Active subwoofer (:SB-WA7) (:SB-WA6) (SC-HT:SB-WA) Type Way Speaker, Bass-ref. Speaker unit (Woofer) [] cm (-7/8 ) cone type, Ω [] [SC-HT] cm (-/8 ) cone type, Ω Output sound pressure level [] 8 db/w (.0 m) [] [SC-HT] 80 db/w (.0 m) Frequency range [] Hz-0 Hz (-6 db) 8 Hz-90 Hz (-0 db) [] [SC-HT] 0 Hz-0 Hz (-6 db) Hz-80 Hz (-0 db) Dimensions (W x H x D) [] 8 x 0 x 0 mm (-7/'' x -/6'' x 0-/'') [] [SC-HT] 00 x 67. x 9 mm (7-7/8'' x -7/6'' x 9-/8'') Mass [] kg (. lb.) [] [SC-HT]. kg (.9 lb.) n GENEA Power supply AC 0 V, 60 Hz Power consumption (Main unit) W (Subwoofer) [] 90 W [] [SC-HT] 0 W Dimensions (W x H x D) (Main unit) 0 x 6 x 60 mm (6-/6'' x -/'' x 0-/'') Mass (Main unit) [].9 kg (. lb.) [] [SC-HT].8 kg (.0 lb.) Power consumption in standby mode: Notes:. Specifications are subject to change without notice. Mass and dimensions are approximate.. Total harmonic distortion is measured by the digital spectrum analyzer. For main unit Marking sign is located on bottom of the unit. W eference QT799

26 istening caution EST. 9 Selecting fine audio equipment such as the unit you ve just purchased is only the start of your musical enjoyment. Now it s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most importantly, without affecting your sensitive hearing. We recommend that you avoid prolonged exposure to excessive noise. Sound can be deceiving. Over time your hearing comfort level adapts to higher volumes of sound. So what sounds normal can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFOE your hearing adapts. To establish a safe level: Start your volume control at a low setting. Slowly increase the sound until you can hear it comfortably and clearly, and without distortion. Once you have established a comfortable sound level: Set the dial and leave it there. Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening for a lifetime. CAUTION! DO NOT STA O PACE THIS UNIT A BOOKCASE, BUIT- CABET O ANOTHE CONFED SPACE. ENSUE THE UNIT IS WE VENTIATED. TO PEVENT ISK OF EECTIC SHOCK O FIE HAZAD DUE TO OVEHEATG, ENSUE THAT CUTAS AND AN OTHE MATEIAS DO NOT OBSTUCT THE VENTIATION VENTS. CAUTION! Do not place anything on top of this unit or block the heat radiation vents in any way. In particular, do not place tape decks or CD/ players on this unit as heat radiated from it can damage your software. User memo: DATE OF PUCHASE DEAE NAME DEAE ADDESS TEEPHONE NUMBE The model number and serial number of this product can be found on either the back or the bottom of the unit. Please note them in the space provided below and keep for future reference. MODE NUMBE SEIA NUMBE Maintenance If the surfaces are dirty To clean this unit, wipe with a soft, dry cloth. Never use alcohol, paint thinner or benzine to clean this unit. Before using chemically treated cloth, carefully read the instructions that came with the cloth. Product Service eference. Damage requiring service The unit should be serviced by qualified service personnel if: (a) The AC power supply cord or the plug has been damaged; or (b) Objects or liquids have gotten into the unit; or (c) The unit has been exposed to rain; or (d) The unit does not operate normally or exhibits a marked change in performance; or (e) The unit has been dropped or the cabinet damaged.. Servicing Do not attempt to service the unit beyond that described in these operating instructions. efer all other servicing to authorized servicing personnel.. eplacement parts When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.. Safety check After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working condition. Product information For product information or assistance with product operation: In the U.S.A., refer to Customer Services Directory on page 7. In Canada, contact the Panasonic Canada Inc. Customer Care Centre at , or visit the website ( or an authorized Servicentre closest to you. QT799 The servicer will require all components to service your system. Therefore, should service ever be necessary, be sure to bring the entire system. 6