Measurement of Modulation Spectrum on GSM/DCS/PCS Mobiles acc. to GSM
|
|
- Robert Simpson
- 6 years ago
- Views:
Transcription
1 Measurement of Modulation Spectrum on GSM/DCS/PCS Mobiles acc. to GSM.0- Application Note MA0_E Subject to change Roland Minihold 98-0 Products: Application Firmware FSE-K0 Spectrum Analyzer FSE + FSE-B7 Digital Radiocommunication Tester CMD 5/55/5
2 Contents. Overview. Problem. Solution 4. Activating the Burst Trigger Output on Option CMD-B7 5. Ordering Information. Annex: Setting Up an External Trigger Circuit. Overview Fast and correct measurement of the spectrum due to modulation of GSM900/DCS800/PCS900 mobile phones according to GSM.0- is problematic due to the IDLE bursts. The suggested solution using Radiocommunication Tester CMD and Option CMD-B7 allows fast measurement of the spectrum due to modulation with the FSE and the Application Firmware FSE-K0 in the complete frequency band without the measured values being affected by the IDLE burst.. Problem For measurements on GSM/DCS/PCS mobile phones using the FSE and Application Firmware FSE-K0, correct triggering is a precondition for accurate measurement of the spectrum due to modulation according to GSM.0-. General trigger capabilities of FSE with FSE-K0: VIDEO: Internal triggering to the video signal is only possible with measurements at the channel frequency (phase/frequency error, carrier power, power vs time). The internal video trigger cannot be used for out-ofchannel measurements (transient spectrum, spectrum due to modulation and spurious measurement). RF POWER: The internal trigger to RF power often is not sufficiently sensitive or broadband for measurements of the spectrum due to modulation in the TX or RX band. EXTERN: Using the FRAME trigger (eg of CMD) as an external trigger leads to incorrect results of the spectrum due to modulation measurement. The reason is the IDLE burst which occurs at every th frame (the mobile is IDLE at every th frame, see Fig. ). This is a problem especially when measuring the spectrum due to modulation where invalid measurement results will also be averaged (ie values measured during the IDLE burst). Using the MULTIFRAME signal of the CMD as an external trigger allows correct measurement of the spectrum due to modulation, but the measurement time would be increased significantly (the period of the MULTIFRAME signal is 0 ms). MULTIFRAME FRAME (Frame Trigger) Bursts Burst Trigger (output signal of digital circuit shown here) IDLE Burst Fig. : Timing of the CMD signals MULTIFRAME, FRAME, the bursts and the burst trigger shown here. The bursts are delayed by slots (577 µs each) relative to the FRAME signal. Every th burst is an IDLE burst. MA0_E ROHDE & SCHWARZ
3 .. Solution A possible solution is the new option CMD-B7 for the CMD. It comprises a digital circuit which suppresses the IDLE burst and produces a real burst trigger. The CMD is used to configure the mobile phone according to the requirements and in addition it supplies the burst trigger signal for the FSE at the rear BNC connector RAMP/TRIG. Thus fast measurements can be made with the aid of FSE and FSE-K0, with the IDLE burst being suppressed. NOTE: The jumper at X on this option has to be changed from position - to - (factory setting is - ). The option CMD-B7 can also be retrofitted by any R&S service center. This BURST TRIGGER signal can of course be used to advantage for all the other TX measurements on the mobile that can be carried out with the FSE/FSE- K0 (phase/frequency error, carrier power, power vs time, transient spectrum and spurious measurement). ext. reference signal CMD 5/55/5 with options CMD-B/CMD-B FSE OUTPUT INTPUT ON Pin ( MULTIFRAME) Multifunction Connector Pin 9 (FRAME) with option CMD-B7: rear output: RAMP/TRIG Rear input: EXT TRIG GATE max. 0 dbm! Coupler FRAME TX / RX BURST TRIGGER MULTI FRAME As an alternative: external burst trigger device Mobile phone ABC DEF GHI STU ÜVW XYZ 0. - RCL S C M Fig. : Block diagram of test setup with option CMD-B7 or alternatively with external burst trigger device. The coupler shall be designed so that the FSE input will not be overdriven (coupling 0 db to 5 db, depending on maximum output power of the mobile phone). MA0_E ROHDE & SCHWARZ
4 4. Activating the Burst Trigger Output on Option CMD-B7 5 IEEE 488 IQ IQ RAMP / TRIG Fig. : Rear-panel detail of CMD with Option CMD-B7. After undoing the marked screws, the option can be withdrawn for changing the jumper position. Fig. 4: The jumper on option CMD-B7 must be changed from position - (factory setting) to position -. MA0_E 4 ROHDE & SCHWARZ
5 Should option CMD-B7 not be available, an external trigger circuit can be configured. The required information can be found in the Annex. 5. Ordering Information Spectrum Analyzer Application Firmware Digital Radiocommunication Tester FSEA 0 ) ) FSE-K CMD 55 ) ) I/Q Outputs CMD-B7 ) ) All FSE 0 models (FSEA0, FSEB 0, FSEM 0, FSEK 0) can be used. ) Depending on the system (GSM 900/DCS800 or PCS 900), other CMD models can also be used. ) If in the CMD both the options CMD-B8/U8 and CMD-B are fitted, option CMD-B7 cannot be installed for reasons of space. (In this case the external trigger circuit has to be used.) ROHDE & SCHWARZ GmbH & Co. KG. P.O.B D-84 München Telephone Telefax Internet: MA0_E 5 ROHDE & SCHWARZ
6 . Annex: Setting Up an External Trigger Circuit Pin assignment of 50-pin MULTIFUNCTION connector of CMD 5/55/5 (Option CMD-B required): 7 50 Pinbelegung Frontplatten-Draufsicht 8 4 Pin 9 of the 50-pin multifunction connector delivers the FRAME signal, pin the MULTIFRAME signal. Reference ground is available at pin FRAME 5 MULTIFRAME BITCLK MULTIFRAME USERTRIGGER SLOTOUT SUPERFRAME SER DUTRLSD SER DUTTXCLK SER DUTRXCLK SER DUTDTR SER DUTRI SER DUTCTS SER DUTDSR SER DUTTXDATA SER DUTRXDATA SER DUTRTS not assigned not assigned GSM-specific clock outputs (USERTRIGGER is input). Time reference is the CMD transmitter (only with option CMD-B) Serial data interface (I/O). Pin Signal designation Function HANDSET OUT HANDSET IN DPG HFF DPG EXTRST DPG EXTD DPG EXTW Handset connection Data pattern generator PRI EXTQ PRI EXTI AQ EXT AI EXT ) I/Q modulation inputs (synthesizer ) I/Q demodulator outputs (level is set to max. ±.5 V peak value via software, AC coupling) SER DSR SER TXDATA SER RXDATA SER RTS SER RLSD SER TXCLK SER RXCLK SER DTR SER RI SER CTS Serial data interface (I/O) BICLK BIDATA BIFRAME Bit interface MA0_E ROHDE & SCHWARZ
7 MULTIFRAME FRAME 5 D 74HCT04 +5V +5V R K R K D 74HCT9 C CTR4 M G G4 D D4 74HCT08 & R K R4 K D 74HCT9 C CTR4 M G G4 D +- D 74HCT04 D 74HCT D 74HCT V R5 K S 4 D5 74HCT74 C D R 5 D4 74HCT08 4 & 5 BURST_TRIG Fig. : Circuit diagram of external trigger device MA0_E 7 ROHDE & SCHWARZ
8 Setting up the circuit The trigger device can easily be set up on a breadboard. Unused inputs should be connected to ground via kω resistors. should be low impedance (wire diameter mm or ground line of sufficient width). The +5 V supply voltage should be carefully blocked by soldering 00 nf capacitors between the IC's supply pin and ground. MA0_E 8 ROHDE & SCHWARZ
BER Measurements on GSM Receivers under Conditions of Fading
BER Measurements on GSM Receivers under Conditions of Fading Application Note 1MA04_0E Subject to change Detlev Liebl 97-10 Products: Signal Generator SMI Digital Radiocommunication Tester CMD55/57 Contents
More informationGSM Mobile Tests under Conditions of Fading
GSM Mobile Tests under Conditions of Fading Application Note 1MA02_0E Subject to change Detlev Liebl 97-09 Products: Digital Radiocommunication Test Set CRTP02 / CRTC02 Signal Generator SMIQ Contents 1.
More informationMobile Tests for GSM 900 / 1800 / 1900 under Fading Conditions
FADING 900 1800 1900 Products: CRTP02, CRTC02, SMIQ Mobile Tests for GSM 900 / 1800 / 1900 under Fading Conditions This application note describes how the most important fading tests for mobile phonesin
More informationTransmitter Measurements on Bluetooth TM Modules
Products: FSE, FSIQ Transmitter Measurements on Bluetooth TM Modules This application note describes how to perform measurements on transmitter modules largely in conformance with the Bluetooth test specifications
More informationCalibrating the CMD Output Level for BER
Ref Lvl -32 dbm -40-50 Marker 1 [T1] -35.50 dbm 5.000000 ms RBW 300 khz RF Att 0 db VBW 3 MHz SWT 5 ms Unit dbm 1 SUMMARY [T1] A RMS AVG -85.86 dbm SGL TRG -60-70 1RM -80 EXT -90-100 -110-120 -130 T1 T2
More informationOut of Band Spurious Measurement for Bluetooth Modules
Products: Signal Analyser FSIQ26/FSP13/FSU8/FSQ26 Out of Band Spurious Measurement for Bluetooth Modules This application notes describes the out of band Spurious emission measurement for Bluetooth modules
More informationBluetooth Tester CBT. Specifications. Specifications. Version January 2006
Specifications Version 03.00 Bluetooth Tester CBT January 2006 Specifications CONTENTS UNIT SPECIFICATIONS...3 TIMEBASE TCXO...3 REFERENCE FREQUENCY INPUT...3 RF GENERATOR...3 RF ANALYZER...5 Power meter
More informationTests on 3G-Base Stations to TS with FSIQ and SMIQ
Products: FSIQ, SMIQ Tests on 3G-Base Stations to TS 25.141 with FSIQ and SMIQ This application note describes how to measure the various WCDMA signals which are used for transmitter tests on FDD base
More informationMeasurements on GSM Base Stations According to Rec
Measurements on GSM Base Stations According to Rec. 11.20 Application Note 1EF23_0L Subject to change 10 September 96, Josef Wolf / Roland Minihold Products: FSE incl. Option FSE-B7 1 Introduction The
More information7000 Series Signal Source Analyzer & Dedicated Phase Noise Test System
7000 Series Signal Source Analyzer & Dedicated Phase Noise Test System A fully integrated high-performance cross-correlation signal source analyzer with platforms from 5MHz to 7GHz, 26GHz, and 40GHz Key
More informationModel 7330 Signal Source Analyzer Dedicated Phase Noise Test System V1.02
Model 7330 Signal Source Analyzer Dedicated Phase Noise Test System V1.02 A fully integrated high-performance cross-correlation signal source analyzer from 5 MHz to 33+ GHz Key Features Complete broadband
More informationTransmitter Measurements on Bluetooth TM Modules with FSP
Products: FSP Transmitter Measurements on Bluetooth TM Modules with FSP This application note shows how to perform measurements on transmitter modules largely in conformance with the Bluetooth test specifications
More informationR&S ETH Handheld TV Analyzer Portable DVB-T/H signal analysis up to 3.6/8 GHz
R&S ETH Handheld TV Analyzer Portable DVB-T/H signal analysis up to 3.6/8 GHz Broadcast Product Brochure 02.00 R&S ETH Handheld TV Analyzer At a glance The R&S ETH handheld TV analyzer was specially designed
More informationConcise NFC Demo Guide using R&S Test Equipment Application Note
Concise NFC Demo Guide using R&S Test Equipment Application Note Products: R&S SMBV100A R&S SMBV-K89 R&S FS-K112PC R&S RTO R&S RTO-K11 R&S CSNFC-B8 R&S FSL R&S FSV R&S FSW R&S ZVL This concise NFC Demo
More informationR&S FSQ-K91/K91n/K91ac WLAN a/b/g/j/n/ac Application Firmware Specifications
R&S FSQ-K91/K91n/K91ac WLAN 802.11a/b/g/j/n/ac Application Firmware Specifications Test & Measurement Data Sheet 03.00 CONTENTS OFDM analysis (IEEE 802.11a, IEEE 802.11g OFDM, IEEE 802.11j, )... 3 Frequency...3
More informationProduction Tests on ICO User Terminals with SMIQ and FSE/FSIQ
Products: SMIQ, FSE, FSIQ Production Tests on ICO User Terminals with SMIQ and FSE/FSIQ The combination of an SMIQ Signal Generator and an FSE / FSIQ Analyzer enables the most important transmitter and
More informationRF Level Test System +20 dbm to 130 dbm
NRVD Power Meter optional Therm. Sensor A B Power: >-15 dbm DUT (Signal Generator, Communication Tester) 1 MHz - 3.5/6 GHz +20 dbm... -130 dbm Diode Sensor Z4 Power: -15 to -40 dbm 6 db Power =< -40 dbm
More informationINSTRUCTION MANUAL MODEL 2710 SUBCARRIER DEMODULATOR
INSTRUCTION MANUAL MODEL 2710 SUBCARRIER DEMODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form
More informationAdvanced Test Equipment Rentals ATEC (2832)
Established 1981 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (2832) This product is no longer carried in our catalog. AFG 2020 Characteristics Features Ordering Information Characteristics
More informationSpectrum Analyzer 1.6 GHz 3 GHz R&S HMS-X
HMS-X_bro_de-en_3607-0181-3X_v0200.indd 1 Product Brochure 02.00 Test & Measurement Spectrum Analyzer 1.6 GHz 3 GHz R&S HMS-X 15.03.2016 15:24:06 1 Basic Unit + 3 Options Key facts Frequency range: 100
More informationFOM-1090 FOM-1090 FOM FOM-1090 w/ DB-25 Female FOM-1091 w/ DB-25 Male
Serial Data Communications Synchronous, Asynchronous or Isochronous Signal rates: DC to 20 MHz FOM-1090 w/ DB-25 Female FOM-1091 w/ DB-25 Male Supported Interface Standards TIA-530, TIA-530A TIA-232 TIA-574
More informationVersatile RF Fading Simulator With R&S FSQ/FSG/FSV and R&S SMU Application Note
Versatile RF Fading Simulator With R&S FSQ/FSG/FSV and R&S SMU Application Note Products: R&S SMU200A R&S SMU-B17 R&S SMU-B14 R&S FSQ R&S FSG R&S FSQ-B17 R&S FSV R&S FSV-B17 R&S FSV-B70 Fading in the baseband
More informationMiniature Synchronous/Asynchronous Fiber Optic Modems
SEPTEMBER 003 ME1570A-FST Miniature Synchronous/Asynchronous Fiber Optic Modems CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 74-746-5500) FREE technical
More informationR&S ZVA110 Vector Network Analyzer Specifications
ZVA110_dat-sw_en_5214-4813-22_cover.indd 1 Data Sheet 04.00 Test & Measurement R&S ZVA110 Vector Network Analyzer Specifications 15.11.2013 14:42:28 CONTENTS Definitions... 3 Specifications... 4 Overview...
More informationSpectrum Analyzer 1.6 GHz 3 GHz HMS-X
Spectrum Analyzer 1.6 GHz 3 GHz 1 Basic Unit + 3 Options Your Spectrum Analyzer Key facts Frequency range: 100 khz to 1.6 GHz/3 GHz* 1 Spectral purity greater than -100 dbc/hz (at 100 khz) SWEEP from 20
More informationSupplements to the FSP Operating Manual TV-Demodulator
Test and Measurement Division Supplements to the FSP Operating Manual TV-Demodulator FSP-B6 1129.8642.02 Dear FSP Customer, The following collection of pages is intended to supplement your FSP operating
More informationTechnical Information. BER Measurement SFL-K17
Technical Information SFL-K17 Option for TV Test Transmitter SFL Bit error rate (BER) can be measured at different points on set-top boxes for digital television. A BER instrument must be able to accept
More informationR3267/3273 Spectrum Analyzers
R3267/3273 Spectrum Analyzers For 3rd-Generation Mobile Communications Present Digital Communication standards (W-CDMA, PDC, PHS, IS-136, GSM, DECT, cdmaone ) R3267/3273 New communication technologies
More informationGeneration and Measurement of Burst Digital Audio Signals with Audio Analyzer UPD
Generation and Measurement of Burst Digital Audio Signals with Audio Analyzer UPD Application Note GA8_0L Klaus Schiffner, Tilman Betz, 7/97 Subject to change Product: Audio Analyzer UPD . Introduction
More informationNPR - Noise Power Ratio Signal Generation and Measurement
Products: AMIQ, SMIQ, SMR, FSEx, FSIQ, FSP, FSU NPR - Noise Power Ratio Signal Generation and Measurement Noise Power Ratio (NPR) is an add-on tool for WinIQSim to generate noise power ratio stimulus signals
More informationR&S FPC-Z10 Teaching Kit Getting Started
R&S FPC-Z10 Teaching Kit Getting Started 1178843602 Getting Started Version 03 This manual describes the following products: R&S FPC-Z10 Teaching Kit (1328.7338.02) 2018 Rohde & Schwarz GmbH & Co. KG Mühldorfstr.
More informationTroubleshooting EMI in Embedded Designs White Paper
Troubleshooting EMI in Embedded Designs White Paper Abstract Today, engineers need reliable information fast, and to ensure compliance with regulations for electromagnetic compatibility in the most economical
More informationI N S T R U C T I O N D A T A
I N S T R U C T I O N D A T A RFL (C37.94) Fiber Service Unit Single Mode 108015-1 RS-449 108015-2 V.35 108015-3 G.703 108015-4 X.21 108015-5 E1 Multimode 107460-1 RS-449 107460-2 V.35 107460-3 G.703 107460-4
More informationR&S FSU Spectrum Analyzer Specifications
R&S FSU Spectrum Analyzer Specifications Test & Measurement Data Sheet 15.00 CONTENTS Frequency... 3 Sweep... 4 Resolution bandwidths... 4 Level... 5 I/Q data... 9 Audio demodulation... 9 Trigger functions...
More informationMULTIDYNE INNOVATIONS IN TELEVISION TESTING & DISTRIBUTION DIGITAL VIDEO, AUDIO & DATA FIBER OPTIC MULTIPLEXER TRANSPORT SYSTEM
MULTIDYNE INNOVATIONS IN TELEVISION TESTING & DISTRIBUTION INSTRUCTION MANUAL DVM-1000 DIGITAL VIDEO, AUDIO & DATA FIBER OPTIC MULTIPLEXER TRANSPORT SYSTEM MULTIDYNE Electronics, Inc. Innovations in Television
More informationDesign and Use of a DTV Monitoring System consisting of DVQ(M), DVMD/DVRM and DVRG
Design and Use of a DTV Monitoring System consisting of DVQ(M), DVMD/DVRM and DVRG When monitoring transmission systems it is often necessary to control the monitoring equipment and to check the measurement
More informationCDMA2000 1xRTT / 1xEV-DO Measurement of time relationship between CDMA RF signal and PP2S clock
Products: CMU200 CDMA2000 1xRTT / 1xEV-DO Measurement of time relationship between CDMA RF signal and PP2S clock This application explains the setup and procedure to measure the exact time relationship
More informationR&S ZND Vector Network Analyzer Specifications
R&S ZND Vector Network Analyzer Specifications year Test & Measurement Data Sheet 02.01 CONTENTS Definitions... 3 Measurement range... 4 Measurement speed... 5 Measurement accuracy... 7 Effective system
More informationGFT Channel Slave Generator
GFT1018 8 Channel Slave Generator Features 8 independent delay channels 1 ps time resolution < 100 ps rms jitter for optical triggered delays 1 second range Electrical or optical output Three trigger modes
More informationAgilent 5345A Universal Counter, 500 MHz
Agilent 5345A Universal Counter, 500 MHz Data Sheet Product Specifications Input Specifications (pulse and CW mode) 5356C Frequency Range 1.5-40 GHz Sensitivity (0-50 deg. C): 0.4-1.5 GHz -- 1.5-12.4 GHz
More informationSignalTap Plus System Analyzer
SignalTap Plus System Analyzer June 2000, ver. 1 Data Sheet Features Simultaneous internal programmable logic device (PLD) and external (board-level) logic analysis 32-channel external logic analyzer 166
More informationV6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver
EM MICROELECTRONIC - MARIN SA 2, 4 and 8 Mutiplex LCD Driver Description The is a universal low multiplex LCD driver. The version 2 drives two ways multiplex (two blackplanes) LCD, the version 4, four
More informationR&S ZNL Vector Network Analyzer Specifications
R&S ZNL Vector Network Analyzer Specifications year Data Sheet Version 01.00 CONTENTS Definitions... 3 Specifications... 4 Measurement range... 4 Measurement speed... 5 Measurement accuracy... 6 Effective
More informationDP1 DYNAMIC PROCESSOR MODULE OPERATING INSTRUCTIONS
DP1 DYNAMIC PROCESSOR MODULE OPERATING INSTRUCTIONS and trouble-shooting guide LECTROSONICS, INC. Rio Rancho, NM INTRODUCTION The DP1 Dynamic Processor Module provides complete dynamic control of signals
More informationApplication Note No. 146
Application Note, Rev. 1.2, February 2008 Application Note No. 146 Low Cost 950-2150 MHz Direct Broadcast Satellite (DBS) Amplifier with the BFP420F RF Transistor draws 27 ma from 5 V supply RF & Protection
More informationUser Manual. TCU/RCU RF Head Control Units. TCU/RCU Analogue 11/6/
11/6/2009 www.elber.com elber@elber.it TCU/RCU RF Head Control Units User Manual Elber s.r.l.- Via Pontevecchio, 42W Phone +39-0185.35.13.33 16042 Carasco (GE) Italy Fax +39-0185.35.13.00 1 Sommario 2
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationR&S SLx8000 Family of UHF/VHF Transmitters Efficient solutions for analog and digital broadcasting standards
Broadcasting Data Sheet 02.01 R&S SLx8000 Family of UHF/VHF Transmitters Efficient solutions for analog and digital broadcasting standards R&S SLx8000 Family of UHF/VHF Transmitters At a glance The UHF/VHF
More informationR&S ZNBT Vector Network Analyzer Specifications
R&S ZNBT Vector Network Analyzer Specifications year Data Sheet Version 05.02 CONTENTS Definitions... 3 Measurement range... 4 Measurement speed... 6 Measurement accuracy of the R&S ZNBT8... 8 Measurement
More informationTests on 3G-Base Stations to TS with R&S Spectrum Analyzers and SMIQ Vector Signal Generator
Products: FSP, FSIQ, FSU, FSQ, SMIQ Tests on 3G-Base Stations to TS 25.141 with R&S Spectrum Analyzers and SMIQ Vector Signal Generator This application note describes how to measure the various WCDMA
More informationLTE RF Measurements with the R&S CMW500 according to 3GPP TS Application Note. Products: R&S CMW500
Jenny Chen May 2014 1CM94_5e LTE RF Measurements with the R&S CMW500 according to 3GPP TS 36.521-1 Application Note Products: R&S CMW500 The 3GPP TS 36.521-1 Radio transmission and reception LTE User Equipment
More informationFeatures of the 745T-20C: Applications of the 745T-20C: Model 745T-20C 20 Channel Digital Delay Generator
20 Channel Digital Delay Generator Features of the 745T-20C: 20 Independent delay channels - 100 ps resolution - 25 ps rms jitter - 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every
More informationWF61 Datasheet. Amp ed RF Technology, Inc.
WF61 Datasheet Amp ed RF Technology, Inc. 1 WF61 Product Specification PRELIMINARY Description 12mm x 12mm x 2.2 mm (WF61A) 12mm x 12mm x 2.7 mm (WF61L) Amp ed RF Tech presents the WF61 WiFi dual band
More informationMAX2660/MAX2661/MAX2663/MAX2671 Evaluation Kits
9-382; Rev ; 9/99 MAX2660/MAX266/MAX2663/MAX267 General Description The MAX2660/MAX266/MAX2663/MAX267 evaluation kits simplify evaluation of the MAX2660/MAX266/ MAX2663/MAX267 upconverter s. They enable
More informationGFT Channel Digital Delay Generator
Features 20 independent delay Channels 100 ps resolution 25 ps rms jitter 10 second range Output pulse up to 6 V/50 Ω Independent trigger for every channel Fours Triggers Three are repetitive from three
More informationInstruction Manual Model Downconverter
Instruction Manual Model 2016-1351 Downconverter August 2010, Rev. A F=512 G=+0.0 MENU MODEL 2016 DOWNCONVERTER CROSS TECHNOLOGIES INC. ALARM REMOTE POWER EXECUTE Data, drawings, and other material contained
More informationR&S EDS300 DME/Pulse Analyzer Specifications
R&S EDS300 DME/Pulse Analyzer Specifications year Data Sheet Version 04.01 CONTENTS Definitions... 3 Specifications... 4 Frequency... 4 Level... 4 DME signal analysis... 4 TACAN signal analysis (R&S EDS-K1
More informationCable guide. for. High Performance Controllers and TeleControllers. Cable types and wiring guidelines
Cable guide for High Performance Controllers and TeleControllers Cable types and wiring guidelines E31 Version 1.13 TABLE OF CONTENTS TABLE OF CONTENTS 2 FIGURES 3 1. User instructions on EMC 5 2. Connecting
More informationVM-100R. 1 RU HEIGHT PROGRAMMABLE 70 AND 140 MHz HIGH-PERFORMANCE VIDEO/AUDIO MODULATOR
VM-100R 1 RU HEIGHT PROGRAMMABLE 70 AND 140 MHz HIGH-PERFORMANCE VIDEO/AUDIO MODULATOR OPTIONS Up to four internal programmable audio subcarrier modulators Support full I:N redundant multiformat configurations,
More informationESU EMI Test Receiver Specifications
ESU EMI Test Receiver Specifications Test & Measurement Data Sheet 02.01 CONTE NT S BASE UNIT... 3 FREQUENCY... 3 RECEIVER SCAN... 4 SWEEP... 4 PRESELECTION... 4 IF AND RESOLUTION BANDWIDTHS... 5 LEVEL...
More information1xEV-DO Test Solutions
Products: R&S SMU200A Vector Signal Generator, R&S FSP, R&S FSU, R&S FSQ Spectrum Analyzers, R&S CMU200 Radio Communication Tester xev-do Test Solutions Application Note MA2 This application note provides
More informationMastering Phase Noise Measurements (Part 3)
Mastering Phase Noise Measurements (Part 3) Application Note Whether you are new to phase noise or have been measuring phase noise for years it is important to get a good understanding of the basics and
More informationHP 71910A and 71910P Wide Bandwidth Receiver Technical Specifications
HP 71910A and 71910P Wide Bandwidth Receiver Technical Specifications 100 Hz to 26.5 GHz The HP 71910A/P is a receiver for monitoring signals from 100 Hz to 26.5 GHz. It provides a cost effective combination
More informationR&S XLx8000 UHF/VHF Transposers Efficient solutions for analog and digital broadcasting standards
Broadcasting Product Brochure 04.00 R&S XLx8000 UHF/VHF Transposers Efficient solutions for analog and digital broadcasting standards R&S XLx8000 UHF/VHF Transposers At a glance R&S XLx8000 UHF/VHF transposers
More informationFibre Optic Modem ODW-611
Fibre Optic Modem ODW-611 PROFIBUS DP to fibre optic link, point-to-point applications The ODW-611 is a fibre optic modem designed for point-to-point fibre optic connections between PROFI- BUS DP networks.
More informationAMIQ-K2 Program for Transferring Various-Format I/Q Data to AMIQ. Products: AMIQ, SMIQ
Products: AMIQ, SMIQ AMIQ-K2 Program for Transferring Various-Format I/Q Data to AMIQ The software AMIQ-K2 enables you to read, convert, and transfer various-format I/Q data files to AMIQ format. AMIQ-K2
More information10Gbps 10km Range 1310nm SFP+ Optical Transceiver
Page 1 of 9 Overview ARIA s 10Gbps 10km Range 1310nm SFP+ Optical Transceiver is designed to transmit and receive optical data over single mode optical fiber with a link length of up to 10km. The transceiver
More informationProduct Brochure Version HZ-15_16_17_bro_en_ _v0100.indd 1
Product Brochure Version 1. R&S HZ-15/R&S HZ-17 Probe Sets R&S HZ-16 Preamplifier E and H near-field emission measurements with test receivers, spectrum analyzers and oscilloscopes HZ-15_16_17_bro_en_5213-6687-12_v1.indd
More informationR&S OSP-B200R/B200S2 Satellite System for R&S OSP User Manual
R&S OSP-B200R/B200S2 Satellite System for R&S OSP User Manual 1178.6733.02 01 User Manual The User Manual describes the following R&S OSP-B200R/B200S2 models and accessories: R&S OSP-B200R/B200S2 (1528.3140.02)
More informationTypical applications:
Typical applications: Managing multiple inputs for growing satellite teleports Extended L-band frequency for Ka-band & HTS applications Routing live traffic to multiple modems ETL s new ultra compact Hurricane
More informationOver 5000 VXI cards and mainframes in stock. 1000's of pieces of Test Equipment in stock. Looking for Test Equipment? Visit us on the web at www.recycledequipment.com Recycled Equipment buys, sells, and
More informationR&S FSMR Measuring Receiver Specifications
Test & Measurement Data Sheet 09.00 R&S FSMR Measuring Receiver Specifications CONTENTS Specifications... 3 Frequency...3 Measuring receiver... 3 Frequency counter...3 RF power...4 RF level (tuned receiver)...5
More informationFibre Optic Modem ODW-622
Fibre Optic Modem ODW-622 RS-232 to fibre optic link, redundant ring or multidrop applications The ODW-622 can be used to create either redundant ring or multidrop solutions for devices with RS-232 interfaces.
More informationR&S FSV-K76 TD-SCDMA BS (DL) Measurements Specifications
FSV_K76_dat-sw_en_5214-1572-22_cover.indd 1 Data Sheet 02.00 Test & Measurement R&S FSV-K76 TD-SCDMA BS (DL) Measurements Specifications 07.08.2013 18:42:49 CONTENTS Specifications... 3 Frequency... 3
More information<EDGE Looped based BER and TX measurements using ARB files on the R&S CMW 500> Products: R&S CMW500 R&S CMW- KW200 R&S CMW- KM200. <Application Note>
Application Note Products: R&S CMW500 R&S CMW- KW200 R&S CMW- KM200 -
More informationEmcore SITU2831 Externally Modulated RF Amplified Fiber Optic Transmitter and SIRU3000 Fiber Optic Receiver
PRELIMINARY Applications RF and microwave antenna signal distribution EW Systems Broadband delay-line and signal processing systems Frequency distribution systems Radar system calibration Phased array
More informationMTP200B WLAN / BT LE Tester
www.tescom.co.kr MTP200B WLAN / BT LE Tester Introduction Tescom s MTP200B is a non-signaling test-based WLAN or BT LE (Low Energy) tester. As one-body equipment incorporating both Signal Generator and
More informationMAXTECH, Inc. BRC-1000 Series. C-Band Redundant LNB Systems. Technology for Communications. System Block Diagrams
MAXTECH, Inc. Technology for Communications BRC-1000 Series C-Band Redundant LNB Systems Introduction Redundant LNB systems minimize system downtime due to LNB failure by providing a spare LNB and an automatic
More informationR&S TS-PMB Switch Matrix Module High-density, 90-channel, full matrix relay multiplexer module
TS-PMB_bro_en_0758-0600-12.indd 1 Product Brochure 02.00 Test & Measurement Switch Matrix Module High-density, 90-channel, full matrix relay multiplexer module Switch Matrix Module At a glance Typical
More informationHMC7056. Block Upconverters / HPA's. Typical Applications. General Description. Features. Functional Block Diagram
Typical Applications Features Compact Design Dual L Band Inputs Dual up conversion to ensure no phase inversion WR28 Output with Isolator PA Enable Digital Gain control Thermal Monitoring and Gain Compensation
More informationOBSOLETE HMC7056. Block Upconverters / HPA's. Typical Applications. General Description. Features. Functional Block Diagram
Typical Applications Features Compact Design Dual L Band Inputs Dual up conversion to ensure no phase inversion WR28 Output with Isolator PA Enable Digital Gain control Thermal Monitoring and Gain Compensation
More informationR&S EDST300 TACAN/DME Station Tester Specifications
R&S EDST300 TACAN/DME Station Tester Specifications year Data Sheet Version 01.01 CONTENTS Definitions... 3 Specifications... 4 Standards... 4 Frequency... 4 TX Power Measurement (R&S EDST300 analyzer)...
More informationThe receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting postamplifier
Applications o 10GBASE-LR at 10.3125 Gbps o 10GBASE-LW at 9.953 Gbps o Other Optical Links Product Description XTBxxA-10LY 10 Gbps SFP+ Bi-Directional Transceiver, 10 km Reach 1270/1330 nm TX/1330/1270
More informationCorrelated Receiver Diversity Simulations with R&S SFU
Application Note Marius Schipper 10.2012-7BM76_2E Correlated Receiver Diversity Simulations with R&S SFU Application Note Products: R&S SFU R&S SFE R&S SFE100 R&S SFC R&S SMU200A Receiver diversity improves
More information10Gbps 10km Range SFP+ Optical Transceiver
Page 1 of 9 Overview This 1310 nm Distributed Feedback (DFB) 10Gbps 10km Range SFP+ Optical Transceiver is designed to transmit and receive optical data over singlemode optical fiber with a link length
More information950RTS Remote Test System
950RTS Remote Test System Specifications DS-1 PCM Interface Format DS-1 AMI or B8ZS Line Code Framing Format D4 Superframe, Extended Superframe or SLC-96 Input Frequency 1.544 Mbit/s ± 150 bit/s Compatibility
More informationR&S RT-ZF5 Ethernet Probing Fixture Manual
R&S RT-ZF5 Ethernet Probing Fixture Manual (=QGB2) Manual Test & Measurement 1333.2318.02 01 This manual describes the R&S RT-ZF5 Ethernet probing fixture (1333.0896.02). 2016 Rohde & Schwarz GmbH & Co.
More informationUSER MANUAL 2-3KW DS SERIES TELECOMPONENTS
FM TRANSMITTERS USER MANUAL 2-3KW DS SERIES SRLS - Via degli Ulivi 3-74020 Montemesola (TA) Italy Document structure This document contains all the technical information relating to the transmitters of
More informationTests on CDMA2000 1xEV-DO Access Terminals in Accordance to IS-866-A
Rohde & Schwarz products: Universal Radio Communication Tester R&S CMU200, Signal Analyzer R&S FSQ, Spectrum Analyzers R&S FSU, R&S FSP and R&S FSL, Signal Generators R&S SMU200A, R&S AMU200A, R&S SMJ100A,
More informationMENU EXECUTE Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2016-1250 Downconverter May 2009 Rev A F=2501.750 G=+25.0 MENU MODEL 2016 DOWNCONVERTER CROSS TECHNOLOGIES INC. ALARM REMOTE POWER EXECUTE Data, drawings, and other material contained
More informationConverting MediaFLO Waveform Files to R&S SFU / SFE / SFE100 ARB Format Using IQWIZARD/WinIQSIM TM for R&S SFx-K35 ARB
Products: R&S SFU Broadcast Test System, R&S SFE Broadcast Tester, R&S SFE100 Test Transmitter Converting MediaFLO Waveform Files to R&S SFU / SFE / SFE100 ARB Format Using IQWIZARD/WinIQSIM TM for R&S
More informationR&S SMF100A Microwave Signal Generator Specifications
R&S SMF100A Microwave Signal Generator Specifications Test & Measurement Data Sheet 04.00 Specifications Specifications apply under the following conditions: 30 minutes warm-up time at ambient temperature,
More informationR&S DST200 RF Diagnostic Chamber Accurate radiated testing of wireless devices 700 MHz to 6 GHz
Test & Measurement Product Brochure 01.00 R&S DST200 RF Diagnostic Chamber Accurate radiated testing of wireless devices 700 MHz to 6 GHz R&S DST200 RF Diagnostic Chamber At a glance The R&S DST200 RF
More informationModel 5240 Digital to Analog Key Converter Data Pack
Model 5240 Digital to Analog Key Converter Data Pack E NSEMBLE D E S I G N S Revision 2.1 SW v2.0 This data pack provides detailed installation, configuration and operation information for the 5240 Digital
More informationInstruction Manual Model Up/Downconverter
Instruction Manual Model 2017-03 Up/Downconverter April 2016, Rev. M DOWNCONVERTER UPCONVERTER U F=1525 D F=1525 G=10.0 G=25.0 MENU MODEL 2017 UP/DOWNCONVERTER CROSS TECHNOLOGIES INC. ALARM REMOTE POWER
More informationRF Semiconductor Test AXRF RF Port Upgrade Kits
RF Semiconductor Test AXRF RF Port Upgrade Kits 2017 Datasheet The most important thing we build is trust Overview AXRF RF Port Upgrade Kits are designed to improve and extend the capability of an existing
More informationInstruction Manual Model UHF, L-Band, Up/Downconverter
Instruction Manual Model 2017-14 UHF, L-Band, Up/Downconverter March 2017, Rev. A RF MONITOR --------- UPCONV-------- MODEL 2017 UP/DOWNCONVERTER RF MONITOR ------- DNCONV-------- DOWNCONVERTER UPCONVERTER
More informationSFP-10G-LR (10G BASE-LR SFP+) Datasheet
SFP-10G-LR (10G BASE-LR SFP+) Datasheet Features Supports rate from 1.25 Gb/ to 10.3 Gb/s bit rates Optical interface compliant to IEEE 802.3ae Electrical interface compliant to SFF-8431 1310nm DFB transmitter,
More informationDATA SHEET. TDA8433 Deflection processor for computer controlled TV receivers INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET File under Integrated Circuits, IC02 August 1991 FEATURES I 2 C-bus interface Input for vertical sync Sawtooth generator with amplitude independent of frequency ertical deflection
More informationThe high-end network analyzers from Rohde & Schwarz now include an option for pulse profile measurements plus, the new R&S ZVA 40 covers the
GENERAL PURPOSE 44 448 The high-end network analyzers from Rohde & Schwarz now include an option for pulse profile measurements plus, the new R&S ZVA 4 covers the frequency range up to 4 GHz. News from
More information