Anchoring in CAD 2 of 15

Transcription

1 Anchoring in CAD

2 Anchoring in CAD 2 of 15 Copyright Any reproduction of the course documents, brochures and SEMA programs in part or in full will be prosecuted. All rights to the software, the brochures and the course documents are with the SEMA GmbH. Any violations of our copyright will be prosecuted under criminal and civil law. SEMA GmbH. All rights reserved. Warranty Limitation No warranty is given for the correctness of the contents of the description of the software and the documents. Since, despite all efforts, errors may occur, we are always happy to receive any details about inaccuracies. We reserve the right to make changes at any time without specified reasons. Since our programs are revised and enhanced for our user s benefit, we are always happy to receive your ideas and suggestions for improvement. Thus, you can help us to further develop and enhance this tool. Publisher: SEMA GmbH Computer Software und Hardware-Vertrieb Dorfmühlstr Wildpoldsried near Kempten, Germany Germany Microsoft, MS-DOS, Windows and Internet Explorer are registered trademarks of the Microsoft Corporation. The Internet Explorer was provided by the Microsoft Corporation with kind permission. Any reproduction or disassembly is prohibited. All rights to this software product are with the Microsoft Corporation. Printed in Germany Art. Nr. INSTR-CAD-ANCH-EN 09/2017

3 Anchoring in CAD 3 of 15 Contents 1. Why anchoring Preparation Inserting an existing module or an own created Ungroup Draw a temporary wall Anchoring of a Two-piece door Example Group Macros before anchoring Anchor CAD Group Anchor CAD Group Anchor CAD Group Macro can be tested by using the copy function Check functionality Store Macro in Work Master Data Example Seperate CAD Group Attach middle part again Draw coverage lines Group Macros Anchor CAD Group Anchor CAD Group Anchor CAD Group Anchor CAD Group

4 Anchoring in CAD 4 of Why anchoring Anchoring With the function anchor, you can fix modules so that If you change components (wall width/height) it reacts and adapt properly in relationship. 2. Preparation 2.1. Inserting an existing module or an own created Switch to the CAD function and Insert Macro Select the Two-piece door macro from Work Master Data

5 Anchoring in CAD 5 of Ungroup Ungroup Macro in individual CAD groups Highlight Macro and ungroup it over Macro/Ungroup 2.3. Draw a temporary wall Draw a temporary wall to place the anchor points there

6 Anchoring in CAD 6 of Anchoring of a Two-piece door 3.1. Example 1 In this example, you have to set the anchor points so, that if you change the macro it changes the glas width, but the opening width stays constant Group Macros before anchoring You have to Group individual CAD elements always before anchoring (picture) Anchor CAD Group 1 Highlight CAD Group and select Others/1 anchor point Set anchor point as shown on the picture

7 Anchoring in CAD 7 of Anchor CAD Group 2 Highlight CAD Group and select Others/1 anchor point Set anchor point as shown on the picture Anchor CAD Group 3 Highlight CAD Group and select Others/2 anchor points Set anchor points as show on the picture Anchor point 1 Anchor point 2

8 Anchoring in CAD 8 of Macro can be tested by using the copy function Select Macro/Copy with reference point By using the third instance select following reference points and confirm with OK Reference point 1 Reference point 2

9 Anchoring in CAD 9 of Check functionality Paste Macro over Macro/Paste (Ctrl+V) and check for functionality Store Macro in Work Master Data Save Macro over Macro/Define Select the reference points as described in section and confirm with OK

10 Anchoring in CAD 10 of Example 2 In this example, you have to set the anchor points so, that if you change the macro it changes the opening width, but the glas width stays constant Repeat Chapter Seperate CAD Group CAD Group must be seperated to prevent a distortion of the profile heads Highlight Group and seperate it in 3 parts over the function Punch Ungroup CAD Group over Macro/Ungroup Attach middle part again Extend over Add, the outer parts to the midsection

11 Anchoring in CAD 11 of Draw coverage lines Coverage lines need to be drawn over the left and the right side of the middlepart to get an optimal representation Select following settings in CAD functions Exaggerate CAD Polygon <Ground plan (G)> Edge

12 Anchoring in CAD 12 of Group Macros Highlight CAD Lines and the middle CAD Polygon and group it Highlight CAD Elements and group it

13 Anchoring in CAD 13 of Anchor CAD Group 1 Highlight CAD Group and select Others/2 anchor points Set anchor points as shown on the picture Anchorpoint 1 Anchorpoint 2

14 Anchoring in CAD 14 of Anchor CAD Group 2 Highlight CAD Group and select Others/1 anchor point Set anchor point as shown on the picture Anchor CAD Group 3 Highlight CAD Group and select Others/1 anchor point Set anchor point as shown on the picture

15 Anchoring in CAD 15 of Anchor CAD Group 4 Highlight CAD Group and select Others/2 anchor points Set anchor points as shown on the picture Anchor point 1 Anchor point 2 Check functionality Define as Macro and save in Work Master Data We recommend to practice anchoring at own examples, because multiple solutions are possible