VR-510 INSTRUCTION MANUAL KENWOOD CORPORATION AUDIO VIDEO SURROUND RECEIVER. About the supplied remote control B MA (K, P) 0011

Transcription

1 AUDIO VIDEO SUOUND ECEIVE V-510 INSTUCTION MANUA KENWOOD COPOATION About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc.). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. Operations Preparation B MA (K, P) 0011 Additional Information emote Control

2 2 Preparations Before applying the power This unit is designed for operation as follows. U.S.A. and Canada... AC 120 V only Australia... AC 240 V only Europe and U.K.... AC 230 V only China and ussia... AC 220 V only *Other countries... AC / V switchable Caution : ead this page carefully to ensure safe operation. Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. We recommend that you retain the original carton and packing materials for future use should you transport or ship the unit in the future. Keep this manual handy for future reference. Accessories FM indoor antenna (1) AM loop antenna (1) F remote antenna (1) emote control unit (1) C-0812 Batteries (6/AA) (4) Safety precautions WANING : TO PEVENT FIE O EECTIC SHOCK, DO NOT EXPOSE THIS APPIANCE TO AIN O MOISTUE. CAUTION ISK OF EECTIC SHOCK DO NOT OPEN CAUTION: TO EDUCE THE ISK OF EECTIC SHOCK, DO NOT EMOVE COVE (O BACK). NO USE-SEVICEABE PATS IN- SIDE, EFE SEVICING TO QUAIFIED SEVICE PESONNE. THE IGHTNING FASH WITH AOWHEAD SYMBO, WITHIN AN EQUIATEA TIANGE, IS INTENDED TO AET THE USE TO THE PESENCE OF UNINSUATED DAN- GEOUS VOTAGE WITHIN THE PODUCT S ENCOSUE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTI- TUTE A ISK OF EECTIC SHOCK TO PESONS. THE EXCAMATION POINT WITHIN AN EQUIATEA TI- ANGE IS INTENDED TO AET THE USE TO THE PES- ENCE OF IMPOTANT OPEATING AND MAINTENANCE (SEVICING) INSTUCTIONS IN THE ITEATUE ACCOM- PANYING THE APPIANCE.

3 Before applying the power For the U.S.A. FCC WANING This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC ules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: eorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. For the U.S.A. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. As an ENEGY STA Partner, Kenwood Corporation has determined that this product meets the ENEGY STA guidelines for energy efficiency. This product can save energy. Saving energy reduces air pollution and lowers utility bills. Maintenance of the unit When the front panel or case becomes dirty, wipe with a soft, dry cloth. Do not use thinner, benzine, alcohol, etc. for these agents may cause discoloration. Contents Caution : ead the pages marked safe operation. Preparations Operations carefully to ensure Before applying the power... 2 Safety precautions... 2 Unpacking... 2 How to use this manual... 4 Special features... 4 Names and functions of parts... 5 emote control unit... 6 Setting up the system... 7 Connecting audio components... 8 Connecting video components... 9 Digital connections Connecting video components (COMPONENT VIDEO) Connecting a DVD player (6-channel input) Connecting the speakers Connecting the terminals Connecting to another room (OOM B) PE OUT connections Connecting the F antenna, external I eceiver and external I epeater Connecting to the AV AUX jacks Connecting the antennas F remote control function Connecting the system control How to use the display operation keys Preparing for surround sound Speaker settings Normal playback Preparing for playback istening to a source component Adjusting the sound ecording ecording audio (analog sources) ecording video ecording audio (digital sources) istening to radio broadcasts Tuning radio stations Presetting radio stations manually eceiving preset stations eceiving preset stations in order (P.CA) Ambience effects Surround modes Surround play DVD 6-channel playback Convenient functions Operations Preparations emote Control In regard to contact cleaner Do not use contact cleaners because it could cause a malfunction. Be specially careful not to use contact cleaners containing oil, for they may deform the plastic component. emote Control Additional Information emote control operations egistering setup codes for other components 36 Operating other components Changing (confirming) the operation mode Preparing for automatic operations (MACO play) Executing an automatic operation To delete the setup code Storing the remote control code of the other components estoring the original factory settings Displaying the CD TEXT data emote control operation of other components In case of difficulty Specifications Additional Information

4 Before applying the power How to use this manual 4 Preparations This manual is divided into four sections: Preparations, Operations, emote Control, and Additional Information. Preparations Shows you how to connect your audio and video components to the receiver and prepare the surround processor. We will guide you to make setting up your system as easy as possible. However, since this receiver works with all of your audio and video components, connecting the system can be fairly complex. Operations Shows you how to operate the various functions available from the receiver. emote Control Shows you how to operate other components using the remote control, as well as a detailed explanation of all remote control operations. Once you have registered your components with the proper setup codes, you ll be able to operate both this receiver and your other AV components (TV, VC, DVD player, D player, CD player, etc.) using the remote control supplied with this receiver. Additional Information Shows you additional information such as In case of difficulty (troubleshooting) and Specifications. Memory back up function Please note that the following items will be deleted from the unit's memory if the power cord is disconnected from the AC outlet for approximately 2 days. Power mode. Input selector settings. Device preset. Picture output. Speaker ON/OFF Volume level. BASS, TEBE, INPUT level. Subwoofer ON/OFF. Dimmer level. Monitor ON/OFF. MD/TAPE settings. 6ch/2ch input setting. isten mode setting. Speaker settings. Input mode setting. Midnight mode setting. Broadcast band. Frequency setting. Preset stations. Tuning mode. Source Direct. F Band. THX. SW E-MIX. Bass Peak evel. Special features True home theater sound This receiver incorporates a wide variety of surround modes to bring you maximum enjoyment from your video software. Select a surround mode according to your equipment or the software you are going to play and enjoy! ª Home THX Cinema THX Select incorporates a complex multichannel digital audio program materials such as Dolby Digital, PO OGIC & DTS which enables multichannel decoding. This system features e-equalization (e-eq), Timbre Matching, Adaptive Decorrelation, Bass Peak evel Manager and oudspeaker Position Time Synchronization, which reproduces similar cinematic effects in the home environment. Dolby Digital The DOBY DIGITA mode lets you enjoy full digital surround from software processed in the Dolby Digital format. Dolby Digital provides up to 5.1 channels of independent digital audio for better sound quality and more powerful presence than conventional Dolby Surround. Dolby Pro ogic II DOBY PO OGIC II, whilst totally compatible with its predecessor PO OGIC, provides greater advantage in surround sound. It allows the users to enjoy the conventional stereo or Dolby Surround with a convincing 5.1 like presentation. PO OGIC II offers special features for controlling the overall spatial, dimensionality, and frontal sound field imaging. PO OGIC II produces an impressive surround sound from video software marked and three-dimensional space from music CD. When listening to music, you will be able to enjoy the experience of sheer STEEO surround sound. Dolby 3 Stereo This surround system reproduces theater-like surround sound from video software marked. The 3 STEEO mode will redirect the Surround signal to the front left and right speakers when only the front and center speakers are used. DTS DTS (Digital Theater System) is a 5.1 channel digital audio format that provides five full-spectrum channels and one low-frequency (subwoofer) channel for unprecedented clarity, optimum channel separation and a (wide) dynamic range. In the DTS mode, the 5.1 channel digital input from a DTS CD, D or DVD disc (carrying the DTS marking) can be played in Digital Surround. Important: When a DTS disc is played on a CD, D or DVD player, noise may be output from the analog output. It is recommended that you connect the digital output of the player to the digital input of this unit. Multi channel music (SS Circle Surround ) SS Circle surround enables you to listen to multi channel sound from the stereo source. We assume you have already enjoyed listening to Dolby digital sound/dts multi channel sound with your multi speakers. Now, this time try listening to the stereo source (ex. Audio CD) using your multi speakers. You may discover a new type of stereo sound through SS Circle Surround. DSP surround modes The DSP (Digital Signal Processor) used for this receiver incorporates a variety of high quality adjustable sound fields, like AENA, JAZZ CUB, THEATE, STADIUM and DISCO. It is compatible with almost any kind of program source. DVD 6-channel input If you own a DVD player equipped with 6-channel output, this receiver allows you to obtain the full surround sound impact of DVD source material featuring multi-channel encoding. Since the source signals are digital and each channel is input independently, the resulting ambience is far superior to what can be achieved with conventional surround sound systems. emote control This remote control has two kinds of signal- Universal I (Infraed) remote signal In addition to the basic receiver, the remote control supplied with this receiver can also operate almost all of your remote controllable audio and video components. Just follow the simple setup procedure to register the components you have connected. F remote signal You can operate the receiver by sending F remote signal from the remote control. The controllable range of the remote control is not influenced by surroundings such as distance or an obstruction. MACO play The MACO function lets you perform a series of operations automatically, like turning ON the power of the receiver and connected components, switching the input selectors, and starting playback. (Be sure to register your components before starting the macro set up procedure).

5 Names and functions of parts CIP indicator MUTE indicator Speaker indicator SP A B TI.VO CIP MUTE DS EON PTY TP TA NEWS Frequency display, Input display, Preset channel display, Surround mode display C FE SW S S S Speaker selection indicators Input channel indicators Output channel indicators Display AUTO SOUND indicator Band indicators DOWNMIX indicator PO OGIC indicator FM AUTO SOUND DIGITA AUTO AM PO OGIC S.DIECT MEMO MHz 3 STEEO MONITO ST. khz DOWNMIX DSP TUNED 3 STEEO indicator STEEO indicator DIGITA indicator S.DIECT indicator AUTO indicator MEMO. indicator ST. indicator TUNED indicator MONITO indicator DSP indicator 5 Preparation AUDIO-VIDEO SUOUND ECEIVE V-510 VOUME CONTO STANDBY MUTI CONTO DTS DOBY DIGITA THX DSP MODE INPUT SEECTO POWE SET UP INPUT MODE DIMME MONITO ON/STANDBY SOUND ISTEN MODE SOUCE DIECT A SPEAKES B BAND AUTO MEMOY DOWN UP PHONES S-VIDEO V AV AUX AUDIO 1 POWE ( ) key Use to switch the power ON/STANDBY. STANDBY indicator 2 MUTI CONTO knob Use to control a variety of settings. 3 SET UP key Use to select the speakers' settings etc. 4 Surround indicators DTS indicator ights when the receiver is in the DTS mode. DOBY DIGITA indicator ights when the receiver is in the Dolby Digital mode. THX indicator ights when the receiver is in the THX mode. DSP MODE indicator ights when the receiver is in the DSP mode. CS 5.1 indicator ights when the receiver is in the CS 5.1 mode. 5 INPUT MODE key 7 Use to switch between the digital and analog inputs. 6 DIMME key Use to adjust the brightness of the display.fi Use to select the EC MODE. 7 MONITO key Use to monitor the source that is connected to the MONITO jack. 8 VOUME CONTO knob 9 PHONES jack Use for headphone listening. 0 SPEAKES A/B keys Use to turn the A/B speakers ON/OFF.! SOUND key Use to adjust the sound quality and ambience BAND key Use to select the broadcast band. # AUTO Use to change TAPE indication to MD. Use to select the auto tuning mode. $ ISTEN MODE key Use to select the listening mode. % MEMOY key Use to store radio stations in the preset memory. ^ SOUCE DIECT key Use to pass the source material direct to the amplifier. & INPUT SEECTO knob Use to select the input sources. * AV AUX (S VIDEO, V, AUDIO /) jacks * Standby mode When standby indicator is lit, this receiver is in standby mode and consumes a small amount of current for back-up. This system can be switched on using remote control.

6 Names and functions of parts emote control unit 6 1 Preparations SHIFT MUSIC AV POWE DIMME SOUND TITE/GUIDE MACO MOVIE MUTE BASS BOOST SUB W. ISTEN M. TUNING BAND VO. VO. TV SYS. POWE THX MENU $ % ^ & * # ETUN /PAGE EC MODE EC ENTE AUTO/MONO F.SHIFT EAN EPEAT ANDOM INPUT SE TV SEECT DISPAY SEECT AUDIO THEME FAVOITE INFO. EXIT AST CHANNE OSD /PAGE ) If the name of a function is different on the receiver and on the remote control, the name of the remote control key in the manual is indicated in parentheses F EMOTE CONTO UNIT C Display 2 Display operation keys Use for operation on the display. 3 SHIFT key Use in combination with the MUSIC and MOVIE keys to change the remote control mode without changing the input selector. 4 MACO key Use in combination with the MUSIC, MOVIE, or TV keys to execute a series of commands automatically (MACO PAY). 5 AV POWE key Use to turn various components on and off. 6 Multi control keys Use to control a variety of settings. Use to operate other components. 7 CH / keys Use to select the channel. 8 MUTE key Use to temporarily mute the sound. 9 SOUND key Use to adjust the sound quality and ambience effects. DIMME key (with F.SHIFT key) fi Use to adjust the brightness of the display. 0 TITE/GUIDE key Use to operate other components.! key Use to operate other components. ETUN/PAGE key Use to operate other EC key Use to operate the selected component. EC MODE key Use to select the EC MODE. # Numeric keys/source operation keys Provide functions identical to those of the original remote control supplied with the component you are controlling. To access the functions printed above the keys, press the numeric key after pressing the F. SHIFT key. Function availability varies for each component. $ MUSIC key Selects the audio inputs and sets the remote control to operate the component registered at the respective input. If you connect audio components from KENWOOD and other makers to the MD/ TAPE or CD jacks, you can set the remote control to operate these components by registering the appropriate setup code at the respective input. MOVIE key Selects the video inputs and sets the remote control to operate the component registered at the respective input. TV key Sets the remote control to operate a TV or cable box. This key does not change the input selector on the receiver. % SYS. POWE key Use to turn the receiver on and off. ^ VO. / keys Use to adjust the receiver volume. & ISTEN M. key Use to select the listening mode. BASS BOOST key (with F. SHIFT key) Use to select the maximum adjustment setting for the low frequency range. * THX key Use to switch the status of THX. SUB W. key (with F. SHIFT key) fi Use in combination with the volume / keys to adjust the volume of the subwoofer. ( MENU key Use to operate other components. ) 5 key Use to operate other components. OSD/PAGE key Use to operate other components. EAN key Use to memorize the operation of the other remote control units. F. SHIFT key Use in combination with the numeric keys to execute alternate commands. Turn the light of the display on and off by pressing and holding this key for more than 2 seconds.

7 Setting up the system Make connections as shown on the following pages. When connecting the related system components, be sure to also refer to the instruction manuals supplied with the components you are connecting. Do not connect the power cord to a wall outlet until all connections are completed. DTS disclaimer clause DTS Digital Surround is a discrete 5.1 channel digital audio format available on CD, D, and DVD software which consequently cannot be decoded and played back inside most CD, D, or DVD players. For this reason, when DTS-encoded software is played back through the analog outputs of the CD, D, or DVD player, excessive noise will be exhibited. To avoid possible damage to the audio system, proper precautions should taken by the consumer if the analog outputs are connected directly to an amplification system. To enjoy DTS Digital Surround playback, an external 5.1 channel DTS Digital Surround decoder system must be connected to the digital output (S/P DIF, AES/EBU, or Tosink) of the CD, D or DVD player. Input mode settings CD/DVD, DVD/6ch, VIDEO2 and VIDEO3 inputs each include jacks for digital audio input and analog audio input. You must select beforehand which type of input is to be used for each connected component. The initial factory settings for audio signal playback (CD/DVD, DVD/6ch) and (VIDEO2, VIDEO3) are digital and analog respectively. To use the analog audio input for playback instead (if, for example, you have connected a VC to the VIDEO2 or VIDEO3 input), you must set the input mode for the corresponding input to the analog mode. After completing connections and turning on the receiver, follow the steps below. INPUT SEECTO 7 Preparations Notes 1. Be sure to insert all connection cords securely. If their connections are imperfect, the sound may not be produced or noise may interfere. 2. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging/unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. 3. Do not connect power cords from components which power consumption is larger than what is indicated on the AC outlet at the rear of this unit. Analog connections Audio connections are made using CA pin cords. These cables transfer stereo audio signal in an analog form. This means the audio signal corresponds to the actual audio of two channels. These cables usually have 2 plugs on each end, one red for the right channel and one white for the left channel. These cables are usually packaged with the source unit, or are available at your local electronics retailer. Microcomputer malfunction If operation is not possible or an erroneous display appears, even though all connections have been made properly, reset the microcomputer referring to In case of difficulty. o CAUTION Be sure to adhere to the followings, or proper ventilation will be blocked causing damage or fire hazard. Do not place any objects impairing heat radiation onto the top of unit. INPUT MODE 1 Use the INPUT SEECTO knob to select CD/DVD, DVD/6ch, VIDEO2, or VIDEO3. 2 Press the INPUT MODE key. Each press switches the setting as follows: In DTS play mode 1 D-AUTO (digital input, auto sound) 2 D-MANUA (digital input, manual sound) In DVD/6ch play mode 1 D-AUTO (digital input, auto sound) 2 D-MANUA (digital input, manual sound) 3 6ch INPT (DVD/6ch input) 4 ANAOG (analog input, manual sound) In modes other than DTS or DVD/6ch play mode 1 D-AUTO (digital input, auto sound) 2 D-MANUA (digital input, manual sound) 3 ANAOG (analog input, manual sound) Digital input: Select this setting to play digital signals from a DVD, CD, or D player. Analog input: Select this setting to play analog signals from a cassette deck, VC, or turntable. Auto sound: In the auto sound mode (AUTO SOUND indicator lights), the receiver selects the listening mode automatically during playback to match the type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial factory setting is auto sound on. To keep the receiver set to the currently selected listening mode, use the INPUT MODE key to select D-MANUA (manual sound). However, even when this setting is selected, there may be cases in which the listening mode is selected automatically to match a Dolby Digital source signal depending on the combination of listening mode and source signal. If the INPUT MODE key is pressed quickly, sound may not be produced.

8 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting audio components 8 SYSTEM CONTO jacks ) Preparations To AC wall outlet EC OUT PAY IN EC OUT PAY IN GND PHONO CD/DVD MD/TAPE MONITO AUDIO IN OUT Video component, 3 head cassette deck, or Graphic equalizer OUT IN Cassette deck or MD recorder OUT CD player OUT Moving Coil (MC) cartridge record player cannot be used directly from the receiver unit. It can only be used when another equalizer amplifier is connected ecord player When you connect the unit and the CD or MD player with the digital connection, you can enjoy a better sound quality.

9 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting video components S-VIDEO S Video jacks PAY IN EC OUT PAY IN PAY IN PAY IN About the S VIDEO jacks 9 S VIDEO MONITO OUT DVD VIDEO 1 VIDEO 1 VIDEO 2 VIDEO 3 Use the S VIDEO jacks to make connections to video components with S VIDEO IN/ OUT jacks. If you use the S VIDEO jacks to connect your video playback components, be sure to use the S VIDEO jacks when connecting your monitor and video recording components. Preparations VIDEO OOM B OUT VIDEO 2 IN CD/DVD DVD IN MONITO OUT VIDEO 1 OUT EC OUT PAY IN PAY IN PAY IN VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 1 IN VIDEO 3 IN Monitor TV VIDEO IN / OUT VIDEO IN IN AUDIO IN / OUT Video Inputs (Yellow CA pin cord) Video deck IN OUT Video inputs and outputs (yellow CA pin cord) IN OUT Audio inputs and outputs OUT DVD player or D player OUT OUT DVD player or D player OUT A video component with digital audio outputs should be connected to the VIDEO2 or VIDEO3 jacks.

10 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Digital connections 10 The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to the receiver, be sure to read the Input mode settings section carefully. 7 Preparations DVD OPTICA DIGITA IN (AUDIO) VIDEO 2 COAXIA DIGITA IN CD/DVD OPTICA VIDEO 3 OPTICA MONITO OPTICA DIGITA OUT MD player OPTICA DIGITA OUT (AUDIO) Optical fiber cable Component with DTS, Dolby Digital, or PCM OPTICA DIGITA OUT Connect the video signal and digital audio signals to the VIDEO 3 jacks. (See Connecting video components.) 9 OPTICA DIGITA OUT (AUDIO) CD player COAXIA DIGITA OUT (AUDIO) Component with DTS, Dolby Digital, or PCM COAXIA DIGITA OUT COAXIA DIGITA OUT (AUDIO) Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See Connecting video components.) 9 F digital demodulator (DEM-9991D) (sold separately) DOBY DIGITA F OUT (AUDIO) PCM OUT D player To connect an D player with a DIGITA F OUT, connect the D player to the KENWOOD F digital demodulator (DEM-9991D). Next, connect the DIGITA OUT jacks of the demodulator to the DIGITA IN jacks of the receiver. Connect the video signal and analog audio signals to the VIDEO 2 or VIDEO 3 jacks. (See Connecting video components.)

11 Setting up the system Connecting video components (COMPONENT VIDEO) If you have connected the receiver to a video component with COMPONENT jacks, you can get a better picture quality than by connecting to the S-VIDEO jacks. 11 Preparations Monitor TV (with component jacks) C IN CB IN C OUT CB OUT Y IN Video ecorder, DVD ecorder, Satellite Cable Tuner & Game Player (with component jacks) Y OUT C OUT CB OUT DVD player (with component jacks) Y OUT Connect to the VIDEO cord. When connecting the TV to the COMPONENT jacks, be sure to connect all the other components to the COMPONENT jacks.

12 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting a DVD player (6-channel input) 12 If you have connected a DVD player to the receiver with digital connection, be sure to read the Input mode settings section carefully. 7 Preparations VIDEO CENTE DVD PAY IN OOM B OUT VIDEO 2 IN CD/DVD IN DVD DVD MONITO OUT VIDEO 1 OUT SUB FONT SUOUND WOOFE DVD / 6 INPUT VIDEO 2 COAXIA VIDEO 1 IN VIDEO 3 IN S VIDEO cord VIDEO OUT (Yellow CA pin cord) FONT OUT / SUOUND OUT / CENTE OUT DVD player SUBWOOFE OUT COAXIA DIGITA OUT (AUDIO) S VIDEO OUT To switch the speakers off, turn SPEAKES A and B OFF or press MUTE key on the remote control unit.

13 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting the speakers 13 Front Speakers A ight eft Center Speaker Preparations FONT SPEAKES CENTE SPEAKES ED BUE GEEN FONT SPEAKES (8 16Ω) SUB WOOFE Use the FONT SPEAKES B terminals if you want to connect a second front speaker system. OANGE (8 16Ω) GAY SUOUND SPEAKES Powered subwoofer ight eft Surround Speakers (Be sure to connect both surround speakers)

14 Setting up the system Connecting the terminals 14 1 Strip coating. 2 oosen. Speaker placement Center speaker Preparations 3 Insert. 4 Secure. Front speaker Surround speaker Subwoofer istening position 1 Strip coating. 2 Push the lever. 3 Insert the cord. 4 eturn the lever. Front speakers : Place to the front left and right of the listening position. Front speakers are required for all surround modes. Center speaker : Place front and center. This speaker stabilizes the sound image and helps recreate sound motion. Be sure to connect a center speaker when using the Dolby 3 Stereo mode. Surround speakers : Place to the direct left and right, or slightly behind, the listening position at even heights, approximately 1 meter above the ears of the listeners. These speakers recreate sound motion and atmosphere. equired for surround playback. Subwoofer : eproduces powerful deep bass sounds. Connection of banana plugs 1 Secure. 2 Insert. Although the ideal surround system consists of all the speakers listed above, if you don't have a center speaker or a subwoofer, you can divide those signals between the available speakers in the speaker settings steps to obtain the best possible surround reproduction from the speakers you have available. Sound will not be heard if the speaker terminal is not fully secured. Never short circuit the and speaker cords. If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly. Speaker impedance After confirming the speaker impedance indications printed on the rear panel of the receiver, connect speakers with matching impedance ratings. Using speakers with a rated impedance other than that indicated on the rear panel of the receiver could result in malfunctions or damage to the speakers or receiver.

15 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting to another room (OOM B) This connection allows you to connect your main system to a monitor TV and speaker system located in another area (OOM B). 15 Preparations VIDEO OOM B OUT FONT SUOUND SUB WOOFE CENTE PE OUT / OOM B Front speakers Power amplifier Monitor TV OOM A (Main System) OOM B I ECEIVE

16 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system PE OUT connections 16 This receiver has additional preout jacks. These can be used for various purposes, but will need to be connected to an external power amplifier as shown in the example below. Preparations FONT SUOUND SUB WOOFE CENTE PE OUT / OOM B Power amplifier Center Speaker Subwoofer Power amplifier Surround speakers Power amplifier Front speakers Power amplifier Connecting a speaker cord directly to a PE OUT jack will not produce any sound from the speaker. To use the PE OUT jacks, press only the SPEAKES A key to the ON position. This connection is available for listening in OOM B.

17 Setting up the system Connecting the F antenna, external I eceiver and external I epeater The remote control for this receiver has the F (radio frequency) and I (infrared rays) transmission function. It enables you to control the receiver not only by aiming at the receiver but also by aiming at the F antenna as well as the external I receiver. In addition, you can enjoy a wider remote control signal range by placing the F antenna and I receiver away from the receiver. 17 KENWOOD components (except DVD player) : System control ) Other components: (egistering setup codes) I EPEATE fl Monitor TV Preparations I EPEATE I OUT I ECEIVE IN CD EMOTE DC 8V 17mA I IN F antenna (For I Transmitter, select F OFF only) I ECEIVE (I sold separately) AC adapter (For F Transmitter, select either 1. F Band 1 or 2. F Band 2 only) MONITO I OUT is free To AC wall outlet ANTENNA F EMOTE Shape of plug to be connected. I eceiver IN Stereo mini plug Sleeve Tip I OUT CD emote Mono mini plug Sleeve Tip ing I IN / OUT SPECIFICATION: Terminal I eceiver IN I OUT CD emote To Tip Signal Signal To ing Ground To Sleeve 8V Ground

18 S VIDEO PAY IN EC OUT MONITO OUT DVD VIDEO 1 PAY IN VIDEO 1 PAY IN VIDEO 2 A PAY IN VIDEO 3 C B Setting up the system Connecting to the AV AUX jacks 18 The AV AUX jacks are convenient for connection of video components such as a camcorder or a video game. Connecting the antennas AM loop antenna The supplied loop antenna is for use indoors. Place it as far as possible from the receiver, TV set, speaker cords and power cord, and adjust the direction for best reception. AM antenna terminal connections 1 Push lever. 2 Insert cord. 3 elease lever. Preparations S VIDEO V AV AUX AUDIO FM indoor antenna The supplied indoor antenna is for temporary use only. For stable signal reception we recommend using an outdoor antenna. Disconnect the indoor antenna when you connect one outdoors. FM antenna terminal connections Insert cord. S VIDEO cord FM outdoor antenna ead the 75Ω coaxial cable connected to the FM outdoor antenna into the room and connect it to the FM 75Ω terminal. VIDEO OUT S VIDEO OUT Camcorder, other VC, video game, digital camera, or portable MD player AUDIO OUT ANTENNA GND Attach to the stand FM 75Ω AM AM loop antenna FM indoor antenna FM outdoor antenna Use an antenna adaptor (Commercially available) To select the source connected to the AV AUX jacks, select AV AUX by using the INPUT SEECTO knob. When you connect the audio source such as the MD player, you do not need to connect the video cable. When you connect the unit and the component with the S VIDEO cord, you can get better picture quality.

19 Setting up the system F remote control function The remote control has the F remote function in addition to the I remote function. The V-510 can receive the remote control commands even when they are installed in a position where the I remote signal can hardly access, for example inside a cabinet. The receiver is not equipped with the F remote bi-directional communication function. The bi-directional communication is available only using the I remote function. emote control operation When the STANDBY indicator is lit, the power turns ON when you press the SYS. POWE key on the remote control. When the power comes ON, press the key you want to operate. Operating receiver range (F Transmitter) F emote antenna 19 Changing the F transmission frequency The F remote function may be unavailable due to radio wave cross talk, etc. In this case, the transmission frequency can be changed. To change the F remote transmission frequency: 1 Open the battery cover on the rear. 10 m Preparations F Transmitter 2 Change the F switch setting. Operating other component range (I Transmitter) F m I Transmitter After changing the F frequency of remote control, be also sure to change that of the receiver. 3 Change the receiver s F reception frequency. Press and hold the SET UP key on the front panel of the receiver for more than 2 seconds. Each time you press the SET UP key, the F reception frequency changes as follows: 1 F BAND 1 2 F BAND 2 3 F OFF Select the same number as the position number of the F switch of the remote control. oading the batteries The remote control signal received by the main unit are I and F signals. When pressing more than one remote control key successively, press the keys securely by leaving an interval of 1 second or more between keys. Notes 1. The supplied batteries may have shorter lives than ordinary batteries due to use during operation checks. 2. When the remote-controllable distance gets shorter than before, replace all batteries with a new ones. 3. Placing the remote sensor in direct sunlight, or in direct light from a high frequency flourescent lamp may cause a malfunction. In such a case, change the location of the system installation to prevent malfunction. 1 emove the cover. 3 Close the cover. 2 Insert the batteries. Important notes Here is list of adjustment which can maximize the operation of your remote control. For optimal operation of the remote control: 1 Aim the remote control toward the room where the receiver is located. 2 Do not position the receiver and remote control near metal (such as heat ducts). Metal can absorb F signals. 3 Make sure the batteries in the remote control are fully charged. Weak batteries will affect the range of the remote control. 4 When there is an obstruction around other equipments that send signal from the remote control, the control distance of the F remote signal will be short. Insert four AA-size (6) batteries as indicated by the polarity markings. Note The tests for range limits of the remote control and the receiver are conducted in open-air distance test. Actual distance of the signal will be based on the construction of the building the unit is being used in as well as other factors such as outside interference.

20 Setting up the system Connecting the system control 20 Preparations Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. This unit is compatible only with the [S-16] mode. The system control operation is not available if the unit is connected in the [XS8], [XS], or [X] connection mode. If your component has the mode select switch, set the connected components to the [S16] mode. SYSTEM CONTO SYSTEM CONTO cord You may connect the system control cord to either the left or right jack. EXAMPE: [S16] mode connections The underlined portion represents the setting of the system control mode. SYSTEM CONTO OPEATIONS emote Control ets you operate this unit with the system remote supplied with the receiver. Automatic Operation When you start playback from a source component, the input selector on this unit switches to that component automatically. Synchronized ecording ets you synchronize recording with the start of playback when recording from CD, MD or analog discs. egistering setup codes for KENWOOD audio components If you own remote controllable KENWOOD audio components that are not compatible with system control, registering the setup code enables you to control those components using the remote control supplied with this unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see egistering setup codes for other components. fl [S16] [S16] [XS] [XS8] [X] [S16] [XS] [XS8] [XS] eceiver Cassette deck or MD recorder CD player ecord player SYSTEM CONTO cord In order to take advantage of the system control operations, the components must be connected to the correct jacks. To use a CD player it must be connected to the CD jacks. To use a cassette deck (or MD recorder) it must be connected to the MD/TAPE jacks. When using more than one CD player (etc.) only the one connected to the specified jacks may be connected for system control. Some CD players and cassette decks are not compatible with the [S16] system control mode. Do not make system connections with equipment that is not [S16] compatible. Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment. Notes 1. [S16] equipment cannot be combined with [X], [XS], and [XS8] equipment for system operations. If your equipment consists of this kind of combination, please do not connect any system control cords. Even without system control cords, normal operations can be carried out without effecting performance. 2. Do not connect system control cords to any components other than those specified by KENWOOD. It may cause a malfunction and damage your equipment. 3. Be sure the system control plugs are inserted all the way in to the system control terminals. Do not connect a system control cord to a cassette deck connected to the MONITO jacks.

21 The remote control sends an F (radio wave) signal to the receiver. For equipment other than the receiver, an I (Infrared) signal is sent. The remote control supplied with this receiver is also capable of controlling components from a variety of manufacturers once you register the appropriate setup codes into the remote control unit. efer to emote control operation of other components for details about the operations available for each component. e How to use the display operation keys To register the setup code, use the display operation 1 key, display operation 2 key, or 5/ keys. Display Display operation 1 5/ Display operation 2 Setting up the system 21 Preparations The display operation 1 key and display operation 2 key work as the function key displayed in the display above. The display operation 1 key SHIFT MUSIC AV POWE MACO MOVIE TV SYS. POWE >05.VC >06.Cable Back Enter [Back] Go back to the previous display. [Home] Go back to the initial display. [Clr] Erase the internal memory. ETUN /PAGE DIMME SOUND TITE/GUIDE EC MODE EC MUTE BASS BOOST SUB W. ISTEN M. TUNING BAND ENTE AUTO/MONO F.SHIFT VO. VO. EAN EPEAT ANDOM INPUT SE TV SEECT DISPAY AUDIO THEME SEECT FAVOITE INFO. EXIT THX AST CHANNE MENU OSD /PAGE When the display goes off The display operation 2 key [Enter] Enter the selected item. [Menu] Display the menu. [Setup] Go to the setup display. [Exit] Exit from the current operation. [Sel] Select the item. The display goes off automatically when you do not operate for more than 8 seconds. In this case, press the display operation 1 key, display operation 2 key, or 5/ keys. When you are confused about what s being displayed Press the display operation 1 key repeatedly until Menu appears in the display. The display returns to the initial display. F EMOTE CONTO UNIT C Display operation 1 key Use this key to go back to the previous display or initial display. 2 Display operation 2 key Gets you into and out of the preset code registration mode. 3 Display The information for setup is displayed. 4 5/ keys Use these keys to select the source or setup code. 5 MOVIE, MUSIC, and TV keys Use these keys to select the input you want to register. 6 AV POWE key Once you have entered the setup code for another component, you can press this key to turn power to that component on or off. This lets you confirm that you entered the code properly.

22 Preparing for surround sound Speaker settings 22 Preparations To enable you to obtain optimum enjoyment from the receiver s listening modes, make sure to complete the speaker settings (subwoofer, front, center, and surround speakers) as described below. 1 2 MUTI CONTO POWE ( ) Display operation 1 Display operation 2 SET UP Select a speaker system. 1 Press the SET UP key such that the subwoofer setting indication SUBWOOFE scrolls across the display. SUBWOOFE will be scrolled from right to left Blinks When you operate on the remote control unit 1 Press the display operation 2 [Menu] key repeatedly until 01.I appears in the display of the remote control unit. >01.I >02.Surround Home Enter 2 Press the 5/ keys to select 02.Surround, then press the display operation 2 [Enter] key. SetUp Home Next 2 Use the MUTI CONTO knob or 5/ keys to select the appropriate subwoofer setting. 1 ON : Subwoofer setting mode to the receiver is ON. 2 OFF : Subwoofer setting mode to the receiver is OFF. The initial setting is SUBWOOFE ON. When SUBWOOFE OFF is selected, the front speakers are automatically set to G and the procedure skips to step 5. When subwoofer output sound is required, select FONT NM. SP A B TI.VO CIP MUTE S DS EON PTY TP TA NEWS C S SW S Blinks 5/ SYS. POWE ( ) Turn on the power to this receiver by pressing POWE ( ) or SYS. POWE ( ) key. SP A B TI.VO CIP MUTE PTY DS EON TP TA NEWS C FE SW S S S DIGITA AUTO S.DIECT MEMO STEEO MONITO ST. DSP TUNED FM AUTO SOUND DIGITA AUTO AM PO OGIC S.DIECT MEMO MHz 3 STEEO MONITO ST. khz DOWN MIX DSP TUNED 3 3 Press the SET UP or display operation 2 [Next] key to accept the setting. The front speakers setting indication FONT scrolls across the display 4 Use the MUTI CONTO knob or 5/ keys to select the appropriate front speakers setting. 1 NM/THX (normal) : Average size front speakers are connected to the receiver. 2 G (large) : arge front speakers are connected to the receiver. SP A B TI.VO C CIP MUTE FE SW DS EON PTY S S S TP TA NEWS Blinks Under certain circumstances, for FONT G selection, no sound will be heard from the subwoofer even when it is set to ON. However, if you select SW E-MIX ON when subwoofer is selected, you may hear sound from the subwoofer. 5 Press the SET UP or display operation 2 [Next] key to accept the setting. The center speaker setting indication CENTE scrolls across the display. 6 Use the MUTI CONTO knob or 5/ keys to select the appropriate center speaker setting. If you have selected G as the front speakers setting, 1 NM/THX (normal) : An average size center speakeris connected to the receiver. 2 G (large) : A large center speaker is connected to the receiver. 3 OFF : Center speaker setting mode to the receiver is OFF. If you have selected NM as the front speakers setting, 1 NM/THX : Center speaker setting mode to the receiver is ON. 2 OFF : Center speaker setting mode to the receiver is OFF. 7 Press the SET UP or display operation 2 [Next] key to accept the setting. The surround speaker setting indication SUOUND scrolls across the display. 8 Use the MUTI CONTO knob or 5/ keys to select the appropriate surround speaker setting, If you have selected G as the center speaker setting, 1 NM/THX (normal) : Average size surround speakers are connected to the receiver. 2 G (large) : arge surround speakers are connected to the receiver. 3 OFF : Surround speaker setting mode to the receiver is OFF. If you have selected other than G as the center speaker setting, 1 NM/THX : Surround speaker setting mode to the receiver is ON. 2 OFF : Surround speaker setting mode to the receiver is OFF. 9 Press the SET UP or display operation 2 [Next] key to accept the setting. The subwoofer remix setting indication SW E-MIX scrolls across the display. Select the subwoofer re-mix setting. FM AUTO SOUND DIGITA AUTO AM PO OGIC S.DIECT MEMO MHz 3 STEEO MONITO ST. khz DOWN MIX DSP TUNED 1 Use the MUTI CONTO knob or 5/ keys to select the appropriate subwoofer remix setting. 1 ON : Subwoofer re-mix set mode to the receiver is ON. 2 OFF : Subwoofer re-mix set mode to the receiver is OFF. This is the THX preferred setting. Continued to next page

23 Preparing for surround sound 4 5 SW E-MIX scrolls across the display SP A B TI.VO FM AUTO SOUND CIP MUTE AM PO OGIC SW MHz 3 STEEO DS EON PTY khz DOWN MIX TP TA NEWS DIGITA AUTO S.DIECT MEMO MONITO ST. DSP TUNED 2 Press the SET UP or display operation 2 [Next] key to accept the setting. The receiver enters the speaker volume level adjustment mode. In step 4, indications appear only for the selected channels of the speakers that require adjusting. Adjust the speaker volume. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Use the MUTI CONTO knob or 5/ keys to adjust the volume of the test tone output from the speaker channel to be adjusted. The channel indication blinks while the test tone is being output. SP A B TI.VO CIP MUTE PTY DS EON TP TA NEWS C FE S S S The test tone is heard from the speakers in the following sequence for 2 seconds each: = = C = = S = S = SW SP A B TI.VO C CIP MUTE FE SW DS EON PTY S S S TP TA NEWS FM AUTO SOUND AM PO OGIC MHz 3 STEEO khz DOWN MIX FM AUTO SOUND AM PO OGIC MHz 3 STEEO khz DOWN MIX FM AUTO SOUND AM PO OGIC MHz 3 STEEO khz DOWN MIX DIGITA AUTO S.DIECT MEMO MONITO ST. DSP TUNED If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. If the speaker setting selects are OFF, the speaker level settings are reset. 2 Press the SET UP or display operation 2 [Next] key. The test tone is turned off. The receiver enters the mode for inputing the bass peak level and the current peak level will be shown. To obtain accurate output levels, it is recommended to use a handheld Sound Pressure evel (SP) meter. eadings should be taken from your actual listening position and adjust the level of each speaker to 75dB SP (C-weighted/ slow meter mode). Adjust the bass peak level. A restriction is put on the low frequency so that the bass peak level will not go higher than the acceptable level when the volume is increased. If subwoofer speaker is OFF, the limitation will affect the low frequency of the front left and right speakers. SP A B TI.VO CIP MUTE PTY DS EON TP TA NEWS FE SW S S S DIGITA AUTO S.DIECT MEMO MONITO ST. DSP TUNED 1 Use the MUTI CONTO knob or 5/ keys to adjust the bass peak level to 30. The bass peak level may be adjusted from 30dB to 0dB and OFF. When no subwoofer is in use, the test tone will be output from the front channel speakers. 2 To find the bass peak level limit, keep increasing the bass peak level by using the MUTI CONTO knob or 5/ keys while test tone is being output until the clip point of the subwoofer is found. DIGITA AUTO S.DIECT MEMO MONITO ST. DSP TUNED 3 Press the SET UP or display operation 2 [Next] key. The receiver enters the mode for inputting the distance to the speakers. 6 Input the distance to the speakers. 1 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to front left speaker : feet (meters) Distance to center speaker : feet (meters) Distance to front right speaker : feet (meters) Distance to surround right speaker : feet (meters) Distance to surround left speaker : feet (meters) Distance to subwoofer : feet (meters) 2 Use the MUTI CONTO knob or 5/ keys to select the distance to the front speakers. The speaker indicator to be adjusted blinks. SP A B TI.VO C CIP MUTE FE DS EON PTY S S TP TA NEWS SW S The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increment. 3 Press the SET UP or display operation 2 [Next] key. 4 epeat steps 2 and 3 to input the distance for each of the speakers. 5 Setup is complete when the input indication reappears. The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. SP A B TI.VO C CIP MUTE FE SW DS EON PTY S S S TP TA NEWS Indication in feet SP A B TI.VO C CIP MUTE FE SW DS EON PTY TP TA NEWS S S S FM AUTO SOUND AM PO OGIC MHz 3 STEEO khz DOWN MIX Indication in meters Display when all speakers have been selected. DIGITA AUTO S.DIECT MEMO MONITO ST. DSP TUNED Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CIP indicator will blink. Adjust the input level. CIP DS TP 1 Use the INPUT SEECTO knob to select the source which you want to adjust. You can store a separate input level for each input source. If the MONITO function is ON, you can store an input level for when MONITO is on independently of the input levels for the input sources. 2 Press the SOUND key repeatedly until the INPUT indication appears. 3 Use the MUTI CONTO knob or 5/ keys to adjust the input level. FM AUTO SOUND DIGITA AUTO AM PO OGIC S.DIECT MEMO MHz 3 STEEO MONITO ST. khz DOWN MIX DSP TUNED The adjustment mode is displayed for approximately eight seconds. The input level may be adjusted to any one of three settings:0db, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. 23 Preparations