DM Series Industrial Monitor Page 1

Transcription

1 DM Series Industrial Monitor Page 1

2 Revision Date Version Changes Added DM-121GX models information Added DM-190 rack mount installation Added the smartosd appendix Cautions for VESA mounting kit are added in p46, p AV-5300 AD Board CN25 connector pin 3 voltage changed to +9V~+36V input Updated Figure 1-3 and Section 4.4 for AV-5300 AD Board V Correct Figure 4-14 labeling Revised CN7 connector as 12V power Revised CN7 connector as 12V power; added connector pinouts Correct LVDS connector label Initial Release Page 2

3 Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. TRADEMARKS All registered trademarks and product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners. Page 3

4 Manual Conventions WARNING! Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. Warnings are easy to recognize. The word warning is written as WARNING, both capitalized and bold and is followed by text. The text is the warning message. A warning message is shown below: WARNING: This is an example of a warning message. Failure to adhere to warning messages may result in permanent damage to the DM Series or personal injury to the user. Please take warning messages seriously. CAUTION! Cautionary messages should also be heeded to help reduce the chance of losing data or damaging the DM Series. Cautions are easy to recognize. The word caution is written as CAUTION, both capitalized and bold and is followed. The italicized text is the cautionary message. A caution message is shown below: Page 4

5 CAUTION: This is an example of a caution message. Failure to adhere to cautions messages may result in permanent damage to the DM Series. Please take caution messages seriously. NOTE: These messages inform the reader of essential but non-critical information. These messages should be read carefully as any directions or instructions contained therein can help avoid making mistakes. Notes are easy to recognize. The word note is written as NOTE, both capitalized and bold and is followed by text. The text is the cautionary message. A note message is shown below: NOTE: This is an example of a note message. Notes should always be read. Notes contain critical information about the DM Series. Please take note messages seriously. Page 5

6 Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the installation. Contact the IEI reseller or vendor you purchased the DM Series from or contact an IEI sales representative directly. To contact an IEI sales representative, please send an to The items listed below should all be included in the DM Series package. 1 x DM-190/170/150/121/104/84 series industrial monitor. 1 x AC Power cable 1 x VGA Cable 1 x 45W AC Power Adapter (DM-190 / 170 / 150 / 121) 1 x 25W AC Power Adapter (DM-104 / 84) 5 x Replacement Round Head Screw 5 x Replacement Flat Head Screw 5 x Replacement Wire Strain Band 1 x User Manual on CDROM 1 x Power Cable for Terminal Block (Optional for M model) 1 x Touch Panel RS-232 Cable / Touch Pen / Driver CDROM (for T-R model) 1 x Touch Panel USB Cable / Touch Pen / Driver CDROM (for USB/T-R model) Images of the above items are shown in Chapter 5. Page 6

7 Table of Contents 1 INTRODUCTION DM SERIES INDUSTRIAL MONITOR OVERVIEW Standard Features Model Variations Base Model Variants APPLICATIONS AND FEATURES DM Series Industrial Monitor Applications DM Series Industrial Monitor Features EXTERNAL OVERVIEW Front View Bottom Panel View AD Board SERIES SPECIFICATIONS CERTIFICATIONS MECHANICAL OVERVIEW INTRODUCTION FRONT PANEL Front Panel Variants Front Panel Variant Front Panel Variant Front Panel Variant BOTTOM PANEL Available Connectors DM-65 Connectors DM-84 Connectors DM-104 Connectors DM-121 Connectors DM-150 Connectors DM-170 Connectors DM-190 Connectors Page 7

8 2.4 PHYSICAL DIMENSIONS General Physical Dimensions DM-190 Physical Dimensions DM-170 Physical Dimensions DM-150 Physical Dimensions DM-121 Physical Dimensions DM-104 Physical Dimensions DM-84 Physical Dimensions DM-65 Physical Dimensions OPTIONAL MOUNTING KITS DM-65 Mounting Kits DM-84 Mounting Kits DM-104 Mounting Kits DM-121 Mounting Kits DM-150 Mounting Kits DM-170 Mounting Kits DM-190 Mounting Kits MOUNTING OPTIONS Panel Mounting Rack and Cabinet Mounting Wall Mounting DIN Rail Mounting Monitor Arm or Stand Mounting LCD AND TOUCH PANEL SPECIFICATIONS LCD SPECIFICATIONS LCD Overview DM-190 LCD Specifications DM-170 LCD Specifications DM-150 LCD Specifications DM-121 LCD Specifications DM-104 LCD Specifications DM-84 LCD Specifications DM-65 LCD Specifications OPTIONAL TOUCH PANELS Page 8

9 3.2.1 Touch Panel Models Touch Panel Dimensions Touch Panel Specifications Touch Panel RS-232 Controller Specifications Touch Panel USB Controller Specifications POWER ADAPTERS AD BOARDS AD BOARD OVERVIEW AV-9350 AD BOARD AV-9350 AD Board Overview AV-9350 AD Board Connectors AV-9350 AD Board Layout AV-9350 Peripheral Interface Connectors AV-9350 Rear Panel Connectors AV-9350 Onboard Jumper AV-9350 Internal Peripheral Connectors V Power Connector Debugged Port Connector External OSD and LED Indication Connector Serial Communications Connector TTL Output Connector VGA Connector AV-9350 External (Rear Panel) Connectors DC 12V Connector RS232 Serial Connector OSD Control Buttons VGA Connector AV-9350 Onboard Jumper LCD Panel (TTL) Voltage Select Jumper AV-5350 AD BOARD AV-5350 AD Board Overview AV-5350 AD Board Connectors AV-5350 AD Board Layout AV-5350 Peripheral Interface Connectors Page 9

10 4.3.5 AV-5350 Rear Panel Connectors AV-5350 Onboard Jumper AV-5350 Internal Peripheral Connectors V Power Connector V Power Connector Backlight Inverter Connector External OSD and LED Indication Connector LVDS Output Connector VGA Connector AV-5350 External (Rear Panel) Connectors DC 12V Connector VGA Connector AV-5350 Onboard Jumper LCD Panel Voltage Select Jumper AV-5300 AD BOARD OVERVIEW AV-5300 AD Board Connectors AV-5300 AD Board Layout AV-5300 Peripheral Interface Connectors AV-5300 Rear Panel Connectors AV-5300 On-board Jumpers AV-5300 Internal Peripheral Connectors Auto-Dimming Connector Debug Port Connector External OSD and LED Indication Connector Backlight Inverter Connector LVDS Output Connector Power Output Connector Power Input Connector VGA Connector AV-5300 On-board Jumpers LCD Panel Power Input Jumper LCD Panel Voltage Select Jumper AV-5300 External (Rear Panel) Connectors DC 12V Connector VGA Connector Page 10

11 DVI-D Connector INSTALLATION INSTALLATION PRECAUTIONS UNPACKING Packaging Unpacking Procedure Packing List PRE-INSTALLATION PREPARATION Tools Voltage Select Jumper Settings CONNECTORS Rear Panel Connectors Overview VGA Connector DVI-D Connector V Power Connector Optional DC Power Connector Optional RS-232 Touch Panel Connector Optional USB Touch Panel Connector MOUNTING THE DM SERIES INDUSTRIAL MONITOR Panel Mounting Standard Panel Mounting DM-65 Panel Mounting Cabinet and Rack Installation Standard Cabinet and Rack Installation DM-190 Cabinet and Rack Installation DM-84 and DM-65 Cabinet and Rack Installation DIN Rail Installation Wall Mounting Monitor Stand Installation Monitor Arm Installation ON-SCREEN-DISPLAY (OSD) CONTROLS USER MODE OSD STRUCTURE OSD Buttons Page 11

12 6.1.2 OSD Menu Structure All Models Except DM DM-65 OSD Menu Structure USING THE OSD Main Display Features Color Language OSD Configurations Signal Backlight SOFTWARE DRIVERS INTRODUCTION DRIVER INSTALLATION TOUCH PANEL DRIVER CONFIGURATION GASKET REPLACEMENT GASKET REPLACEMENT A SAFETY PRECAUTIONS A.1 SAFETY PRECAUTIONS A.1.1 General Safety Precautions A.1.2 Anti-static Precautions A.2 MAINTENANCE AND CLEANING PRECAUTIONS A.2.1 Maintenance and Cleaning A.2.2 Cleaning Tools B CERTIFICATIONS B.1 ROHS COMPLIANT B.2 IP 65 COMPLIANT FRONT PANEL C SMARTOSD C.1 IEI SMARTOSD QUICK INSTALLATION GUIDE C.2 PRE-INSTALLATION NOTICE C.3 SOFTWARE ILLUSTRATION C.3.1 EDID Page C.3.2 Image Page Page 12

13 C.3.3 Display Page (for analog signal) C.3.4 Color Page C.3.5 PIP Page C.3.6 System Page C.3.7 User Page C.3.8 About Page C.4 INSTALL SOFTWARE C.5 SMARTOSD FAQ C.5.1 Windows 2000 Installation Failure C.5.2 Vista Installation Failure C.5.3 Model Failure C.5.4 DCC Port Failure D INDEX Page 13

14 List of Figures Figure 1-1: Typical Monitor Front View...25 Figure 1-2: Typical Bottom Panel View...26 Figure 1-3: AV-5300 AD Board...27 Figure 2-1: Front Panel Variant Figure 2-2: Front Panel Variant Figure 2-3: Front Panel Variant Figure 2-4: DM-190 Physical Dimensions (millimeters)...39 Figure 2-5: DM-170 Physical Dimensions (millimeters)...40 Figure 2-6: DM-150 Physical Dimensions (millimeters)...41 Figure 2-7: DM-121 Physical Dimensions (millimeters)...42 Figure 2-8: DM-104 Physical Dimensions (millimeters)...43 Figure 2-9: DM-84 Physical Dimensions (millimeters)...44 Figure 2-10: DM-65 Physical Dimensions (millimeters)...45 Figure 2-11: Typical Panel Mounting...50 Figure 2-12: Typical Rack or Cabinet Mounting...51 Figure 2-13: Typical Wall Mounting...52 Figure 2-14: Typical DIN Rail Mounting...53 Figure 2-15: Typical Monitor Arm or Stand Mounting...54 Figure 4-1: AV-9350 AD Board Overview...72 Figure 4-2: Connector and Jumper Locations...73 Figure 4-3: 5V Power Connector Location...76 Figure 4-4: Debugged Port Connector Location...77 Figure 4-5: External OSD and LED Indication Connector Location...79 Figure 4-6: Serial Communications Connector Location...80 Figure 4-7: TTL Output Connector Location...82 Figure 4-8: VGA Connector Location...84 Figure 4-9: AV-9350 External (Rear Panel) Connectors...84 Page 14

15 Figure 4-10: RS232 Serial Connector Pinout Locations...86 Figure 4-11: VGA Connector Pinout Locations...88 Figure 4-12: Jumpers...88 Figure 4-13: Jumper Location...89 Figure 4-14: AV-5350 AD Board Overview...91 Figure 4-15: Connector and Jumper Locations...92 Figure 4-16: 5V Power Connector Location...95 Figure 4-17: 12V Power Connector Location...96 Figure 4-18: Backlight Inverter Connector Location...97 Figure 4-19: External OSD and LED Indication Connector Location...98 Figure 4-20: LVDS Output Connector Location...99 Figure 4-21: VGA Connector Location Figure 4-22: AV-5350 External (Rear Panel) Connectors Figure 4-23: VGA Connector Pinout Locations Figure 4-24: Jumpers Figure 4-25: Jumper Location Figure 4-26: AV-5300 AD Board Overview Figure 4-27: Connector and Jumper Locations Figure 4-28: Auto-dimming Connector Location Figure 4-29: Debug Port Connector Location Figure 4-30: External OSD and LED Indication Connector Location Figure 4-31: Backlight Inverter Connector Location Figure 4-32: LVDS Output Connector Location Figure 4-33: Power Output Connector Locations Figure 4-34: Power Input Connector Locations Figure 4-35: VGA Connector Location Figure 4-36: Jumpers Figure 4-37: Jumper Locations Figure 4-38: AV-5300 External (Rear Panel) Connectors Figure 4-39: VGA Connector Pinout Locations Figure 4-40: DVI-D Connector Pinout Locations Figure 5-1: Monitor Rear Panel Connections Page 15

16 Figure 5-2: VGA Connector Figure 5-3: DVI-D Connector Figure 5-4: 12V Power Connector Figure 5-5: DC Power Connector Figure 5-6: Optional RS-232 Touch Panel Connector Figure 5-7: Optional USB Touch Panel Connector Figure 5-8: Panel Opening Figure 5-9: Insert the Monitor Figure 5-10: Panel Mounting Clamp Position Figure 5-11: DM-65 Panel Mounting Figure 5-12: Secure the Cabinet/Rack Bracket Figure 5-13: Install into a Cabinet/Rack Figure 5-14: Rack Mounting Nuts and Bolts Installation (DM-190) Figure 5-15: Rack Mounting Bracket Installation (DM-190) Figure 5-16: Rack Mounting (DM-190) Figure 5-17: DIN Rail Mounting Bracket Figure 5-18: Screw Locations Figure 5-19: Mounting the DIN RAIL Figure 5-20: Secure the Assembly to the DIN Rail Figure 5-21: Wall-mounting Bracket Figure 5-22: Monitor Support Screws Figure 5-23: Wall Mounting the Monitor Figure 5-24: VESA Mounting Holes Figure 5-25: Monitor Stand Mounting Figure 5-26: Monitor Arm Mounting Figure 6-1: OSD Control Buttons for All Models Except DM Figure 6-2: DM-65 OSD Control Buttons Figure 6-3: Main Display Features Figure 6-4: Color Options Figure 6-5: Language Menu Figure 6-6: OSD Configurations Menu Figure 6-7: Signal Menu Page 16

17 Figure 6-8: Backlight Menu Figure 7-1: Driver CD Pop Up Screen Figure 7-2: Install Shield Wizard Preparation Figure 7-3: Welcome Screen Figure 7-4: Install PS/2 Interface Driver Figure 7-5: Install PS/2 Interface Driver Figure 7-6: Touch Monitor/USB Touch Controller Confirmation Figure 7-7: Controller Installation Directory Figure 7-8: Program Icon Directory Figure 7-9: Installing Figure 7-10: Installation Complete Figure 8-1: Gasket Replacement Figure C-1: DLL Missing Figure C-2: Windows Vista Error Figure C-3: Install as Administrator Figure C-4: Firmware Incompatibility Figure C-5: DCC Port Failure Page 17

18 List of Tables Table 1-1: DM Series Base Model Variants...23 Table 1-2: DM Series Specifications...29 Table 2-1: Front Panel Variants...32 Table 2-2: General Physical Dimensions...38 Table 2-3: DM-65 Mounting Kits...46 Table 2-4: DM-84 Mounting Kits...47 Table 2-5: DM-104 Mounting Kits...47 Table 2-6: DM-121 Mounting Kits...47 Table 2-7: DM-150 Mounting Kits...48 Table 2-8: DM-170 Mounting Kits...48 Table 2-9: DM-190 Mounting Kits...49 Table 2-10: Panel Mounting Clamps...50 Table 2-11: Rack Mounting Clamps...52 Table 3-1: DM-190 LCD Specifications...57 Table 3-2: DM-170 LCD Specifications...58 Table 3-3: DM-150 LCD Specifications...59 Table 3-4: DM-121 LCD Specifications...60 Table 3-5: DM-104 LCD Specifications...61 Table 3-6: DM-84 LCD Specifications...62 Table 3-7: DM-65 LCD Specifications...63 Table 3-8: Touch Panel Models...64 Table 3-9: Touch Panel Dimensions (mm)...66 Table 3-10: Touch Panel Specifications...67 Table 3-11: Touch Panel RS-232 Controller Specifications...68 Table 3-12: Touch Panel USB Controller Specifications...69 Table 3-13: Power Adapter Specifications...70 Table 4-1: AV-9350 Peripheral Interface Connectors...74 Table 4-2: AV-9350 Rear Panel Connectors...74 Page 18

19 Table 4-3: AV-9350 Onboard Jumper...75 Table 4-4: 5V Power Connector Pinouts...76 Table 4-5: Debugged Port Connector Pinouts...77 Table 4-6: External OSD and LED Indication Connector Pinouts...78 Table 4-7: Serial Communications Connector Pinouts...79 Table 4-8: TTL Output Connector Pinouts...82 Table 4-9: VGA Connector Pinouts...83 Table 4-10: DC 12V Connector Pinouts...85 Table 4-11: RS232 Serial Connector Pinouts...86 Table 4-12: OSD Control Button JP1 Pinouts...86 Table 4-13: OSD Control Button JP2 Pinouts...86 Table 4-14: OSD Control Button JP3 Pinouts...87 Table 4-15: OSD Control Button JP4 Pinouts...87 Table 4-16: VGA Connector Pinouts...88 Table 4-17: LCD Panel (TTL) Voltage Select Jumper Settings...90 Table 4-18: AV-5350 Peripheral Interface Connectors...93 Table 4-19: AV-5350 Rear Panel Connectors...93 Table 4-20: AV-5350 Onboard Jumper...94 Table 4-21: 5V Power Connector Pinouts...94 Table 4-22: 12V Power Connector Pinouts...95 Table 4-23: Backlight Inverter Connector Pinouts...96 Table 4-24: External OSD and LED Indication Connector Pinouts...98 Table 4-25: LVDS Output Connector Pinouts...99 Table 4-26: VGA Connector Pinouts Table 4-27: DC 12V Connector Pinouts Table 4-28: VGA Connector Pinouts Table 4-29: LCD Panel Voltage Select Jumper Settings Table 4-30: AV-5300 Peripheral Interface Connectors Table 4-31: AV-5300 Rear Panel Connectors Table 4-32: AV-5300 On-board Jumpers Table 4-33: Auto-dimming Connector Pinouts Table 4-34: Debug Port Connector Pinouts Page 19

20 Table 4-35: External OSD and LED Indication Connector Pinouts Table 4-36: Backlight Inverter Connector Pinouts Table 4-37: LVDS Output Connector Pinouts Table 4-38: Power Output Connector Pinouts (CN12) Table 4-39: Power Output Connector Pinouts (CN13) Table 4-40: Power Input Connector Pinouts (CN24) Table 4-41: Power Input Connector Pinouts (CN25) Table 4-42: VGA Connector Pinouts Table 4-43: LCD Panel Power Input Jumper Settings Table 4-44: LCD Panel Voltage Select Jumper Settings Table 4-45: DC 12V Connector Pinouts Table 4-46: VGA Connector Pinouts Table 4-47: DVI-D Connector Pinouts Table 5-1: Rear Panel Connectors Table 5-2: VGA Connector Pinouts Table 5-3: DVI-D Connector Pinouts Table 5-4: Optional RS-232 Touch Panel Connector Pinouts Table 5-5: Optional USB Touch Panel Connector Pinouts Table 6-1: OSD Menus All Models Except DM Table 6-2: DM-65 OSD Menus Table C-1: SmartOSD Menu Structure Page 20

21 Chapter 1 1 Introduction Page 21

22 1.1 DM Series Industrial Monitor Overview DM Series Industrial Monitor The DM series industrial monitor is the latest member of IEI s line of sophisticated LCD designs, and it has been improved to be RoHS compliant. It is designed to fit industrial automation, or any other applications that require minimum installation space and flexible configuration. The flat front panel provides IP 65 protection, which effectively wards off dust and water. Flexible analog or digital interfaces are provided for ease of connection with a management computer. Resistive type touch panels are optional. If remote/non-attentive control is preferred, RS-232 or USB interfaces can be used with customized adapter cables Standard Features All the base models listed in Section have the following standard features LCD monitor VGA Silver color Aluminum front RoHS compliance Model Variations The DM LCD series have the following seven base models. DM-65GS: 6.5 LCD screen DM-84GS: 8.4 LCD screen DM-104GS: 10.4 LCD screen DM-121GS: 12.1 LCD screen DM-150GS: 15 LCD screen DM-170GS: 17 LCD screen DM-190GS: 19 LCD screen Base Model Variants The DM series industrial monitor base models may or may not have a variety of variants. The standard model name is DM-(XX/XXX)GS, where (XX/XXX) refers to either the two or Page 22

23 three digit size of the monitor. Special features with the associated model prefix are listed in Table 1-1. Model Number 9~36V Power Input Touch Screen USB Touch Screen High Luminance DM-(XX/XXX)GS/T-R - Yes - - DM-(XX/XXX)GMS/T-R Yes Yes - - DM-(XX/XXX)GS-USB/T-R - Yes Yes - DM-(XX/XXX)GMS-USB/T-R Yes Yes Yes - DM-(xxx)GXS/T-R - Yes - - DM-(xxx)GXMS/T-R Yes Yes - Yes DM-(xxx)GXS-USB/T-R - Yes Yes - DM-(xxx)GXMS-USB/T-R Yes Yes Yes Yes DM-(XX/XXX)GHS/T-R - Yes - Yes DM-(XX/XXX)GHMS/T-R Yes Yes - Yes Table 1-1: DM Series Base Model Variants 1.2 Applications and Features DM Series Industrial Monitor Applications The DM series industrial monitor is designed for rigorous industrial environments where it may be exposed to both heat and moisture. Its durability and strength also makes it an ideal choice for public access computers. Some possible applications include: Digital Surveillance Digital surveillance X-ray imaging terminal Multimedia advertising platform General Computing o Computer-based testing center o General purpose information system o Mobile nursing station Page 23

24 o Interactive education use Automation & Control o Plant environment monitoring o Factory automation HMI terminal o Shop-floor/MES control Self-service Kiosk o Full-service receptionist kiosk o Hospital self-registrating terminal o Interactive photo kiosk o Video rental kiosk o Self-service POS terminal DM Series Industrial Monitor Features Some of the features of the DM series industrial monitor include: IP 65 compliant aluminum front panel Analog VGA interface supports most general system boards Optional RS-232 or USB interface touch panel Over 300 cd/m2 high brightness and 50000hrs MTFB long lifetime panel Advanced thermal and air-flow design Supports panel, rack, wall, DIN rail, stand and arm mounting M models support 9~36V DC power input for mobile application Long product life support RoHS compliant Analog resistive type touch panel (optional) 1.3 External Overview The DM series industrial monitors are durable devices that can be used in harsh industrial environments. The following sections describe the physical layout of the DM series industrial monitors. Page 24

25 1.3.1 Front View The front of the DM series industrial monitor is a flat panel TFT LCD screen surrounded by an aluminum frame. A control button panel (OSD), if available, is located either vertically on the right side of the frame or horizontally along the bottom of the frame with the following control buttons: LCD On/Off Auto Left Right Menu The OSD panel also has one power LED. Figure 1-1 shows a typical monitor front view. Figure 1-1: Typical Monitor Front View Page 25

26 1.3.2 Bottom Panel View Figure 1-2 shows the bottom panel of the DM-190 monitor. Other models may include or exclude additional connectors. Refer to Section 2.3 for listings of monitors and their connectors. All connectors are fully described in Section 5.4. Figure 1-2: Typical Bottom Panel View Page 26

27 DM Series Industrial Monitor AD Board The DM series industrial monitor AD board provides a wide variety of control interfaces, receiving and managing signals from a CPU card through cabling. Figure 1-3 shows the AV-5300 AD board as a sample of a typical AD board for the DM series industrial monitor. Refer to Chapter 4 for a complete description of AD boards and their connectors. Figure 1-3: AV-5300 AD Board Page 27

28 1.4 Series Specifications Table 1-2 shows the DM Series specifications. Model DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 LCD Size Input Interface VGA VGA VGA VGA DVI-D VGA DVI-D VGA DVI-D VGA DVI-D Max. Resolution 640x x x x600/ 1024x x x x1024 Brightness (cd/m2) 400/ / Contrast 550:1 400:1 500:1 500:1/ 700:1 400:1 500:1 700:1 LCD Color 262K 262K 262K 262K 262K 16.2M 16.2M Pixel Pitch (mm) / Front Frame Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Aluminum Chassis Heavy-duty steel Heavy-duty steel Heavy-duty steel Heavy-duty steel Heavy-duty steel Heavy-duty steel Heavy-duty steel View Angle (H / V) 140/ / / / / / / /130 AD Board AV-9350 AV-5350 AV-5350 AV-5300 AV-5300 AV-5300 AV-5300 Power Adapter 25W 25W 25W 45W 45W 45W 45W OSD function Yes Yes Yes Yes Yes Yes Yes Mounting Panel Wall Rack DIN Arm Stand Panel Wall Rack DIN Arm Stand Panel Wall Rack Arm Stand Panel Wall Rack Arm Stand Panel Wall Rack Arm Stand Panel Wall Rack Arm Stand Panel Wall Rack Arm Dimension (WxHxD) (mm) 183 x 143 x x 178 x x 242 x x 260 x x 309 x x x x 399 x 73 Page 28

29 Model DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 Color Silver Silver Silver Silver Silver Silver Silver Operation Temperature 0~50 C 0~50 C 0~50 C 0~50 C 0~50 C 0~50 C 0~50 C IP Level IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 IP 65 N/G Weight 1kg 1.8kg 3kg 3.8kg 6kg 8.6kg 10kg Table 1-2: DM Series Specifications 1.5 Certifications All DM series industrial monitor models comply with the following international standards: RoHS IP 65 For a more detailed description of these standards, please refer to Appendix B. Page 29

30 THIS PAGE IS INTENTIONALLY LEFT BLANK Page 30

31 Chapter 2 2 Mechanical Overview Page 31

32 2.1 Introduction This chapter describes the general mechanical overview of the DM series monitors including front and bottom panel variations, available interfaces and overall dimensions. 2.2 Front Panel The front panel of the DM series industrial monitor is comprised of a TFT LCD in an aluminum frame with an OSD control panel Front Panel Variants Table 2-1 shows the three front panel variants for the DM series industrial monitor. Model DM-170, DM-150, DM-121, DM-104, DM-84 DM-190 DM-65 OSD Control Panel Location Vertically along the right side of the aluminum frame Horizontally along the bottom of the aluminum frame In line along the bottom of the rear panel Variant Number Table 2-1: Front Panel Variants Page 32

33 2.2.2 Front Panel Variant 1 The following models of the DM series industrial monitor have an OSD control panel located vertically along the right side of the aluminum frame: DM-170 DM-150 DM-121 DM-104 DM-84 Figure 2-1 shows the location of the front panel variant 1 OSD controls. Figure 2-1: Front Panel Variant 1 Page 33

34 2.2.3 Front Panel Variant 2 The following model of the DM series industrial monitor has an OSD control panel located horizontally along the bottom of the aluminum frame: DM-190 Figure 2-2 shows the location of the front panel variant 2 OSD controls. Figure 2-2: Front Panel Variant 2 Page 34

35 2.2.4 Front Panel Variant 3 The following model of the DM series industrial monitor has an OSD control panel located in-line along the bottom of the aluminum frame: DM-65 Figure 2-3 shows the location of the front panel variant 3 OSD controls. Figure 2-3: Front Panel Variant Bottom Panel All peripheral device connectors are located on the bottom panel of the DM series industrial monitor. The following sections describe the bottom panel variants and their associated connectors Available Connectors There are a number of bottom panel peripheral device connectors available for the DM series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block RS-232 serial connector USB connector Page 35

36 2.3.2 DM-65 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-65 series industrial monitor. VGA connector 12V power connector RS-232 serial connector (T-R models only) DM-84 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-84 series industrial monitor. VGA connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) DM-104 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-104 series industrial monitor. VGA connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) Page 36

37 2.3.5 DM-121 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-121 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) USB connector (USB/T-R models only) DM-150 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-150 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) DM-170 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-170 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) Page 37

38 2.3.8 DM-190 Connectors The following is a list of the bottom panel peripheral device connectors used on the DM-190 series industrial monitor. VGA connector DVI-D connector 12V power connector 9~36V terminal block (M models only) RS-232 serial connector (T-R models only) 2.4 Physical Dimensions The following sections describe the physical dimensions for each model of the DM series industrial monitor General Physical Dimensions General physical dimensions for the DM series industrial monitors are shown in Table 2-2. Model Width (mm) Height (mm) Depth (mm) DM DM DM DM DM DM DM Table 2-2: General Physical Dimensions Page 38

39 2.4.2 DM-190 Physical Dimensions The physical dimensions of the DM-190 are shown in Figure 2-4. Figure 2-4: DM-190 Physical Dimensions (millimeters) Page 39

40 2.4.3 DM-170 Physical Dimensions The physical dimensions of the DM-170 are shown in Figure 2-5. Figure 2-5: DM-170 Physical Dimensions (millimeters) Page 40

41 2.4.4 DM-150 Physical Dimensions The physical dimensions of the DM-150 are shown in Figure 2-6. Figure 2-6: DM-150 Physical Dimensions (millimeters) Page 41

42 2.4.5 DM-121 Physical Dimensions The physical dimensions of the DM-121 are shown in Figure 2-7. Figure 2-7: DM-121 Physical Dimensions (millimeters) Page 42

43 2.4.6 DM-104 Physical Dimensions The physical dimensions of the DM-104 are shown in Figure 2-8. Figure 2-8: DM-104 Physical Dimensions (millimeters) Page 43

44 2.4.7 DM-84 Physical Dimensions The physical dimensions of the DM-84 are shown in Figure 2-9. Figure 2-9: DM-84 Physical Dimensions (millimeters) Page 44

45 2.4.8 DM-65 Physical Dimensions The physical dimensions of the DM-65 are shown in Figure Figure 2-10: DM-65 Physical Dimensions (millimeters) Page 45

46 2.5 Optional Mounting Kits The following sections describe the various optional mounting kits available for each model of the DM series industrial monitor. Refer to Section 5.5 for detailed instructions on the different mounting methods for the monitors. CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed DM-65 Mounting Kits Table 2-3 lists the mounting kits available for the DM-65 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DIN Mounting Kit LCD Monitor Arm LCD Monitor Stand DM-65 Included RK-065MS-R10 WK-065MS-R10 DK-065MS ARM-11 STAND-100-RS Table 2-3: DM-65 Mounting Kits DM-84 Mounting Kits Table 2-4 lists the mounting kits available for the DM-84 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DIN Mounting Kit DM-84 PK-84M RK-084MS-R10 WK-084MS-R10 DK-084MS Page 46

47 LCD Monitor Arm LCD Monitor Stand ARM-11 STAND-100-RS Table 2-4: DM-84 Mounting Kits DM-104 Mounting Kits Table 2-5 lists the mounting kits available for the DM-104 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DM-104 PK-104M RK-104MS-R10 WK-104MS-R10 DIN Mounting Kit - LCD Monitor Arm LCD Monitor Stand ARM-11 STAND-100-RS Table 2-5: DM-104 Mounting Kits DM-121 Mounting Kits Table 2-6 lists the mounting kits available for the DM-121 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DM-121 PK-121M RK-121MS-R10 WK-121MS-R10 DIN Mounting Kit - LCD Monitor Arm LCD Monitor Stand ARM-11 STAND-100-RS Table 2-6: DM-121 Mounting Kits Page 47

48 2.5.5 DM-150 Mounting Kits Table 2-7 lists the mounting kits available for the DM-150 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DM-150 PK-150M RK-150MS-R10 WK-150MS-R10 DIN Mounting Kit - LCD Monitor Arm LCD Monitor Stand ARM-31 STAND-100-RS Table 2-7: DM-150 Mounting Kits DM-170 Mounting Kits Table 2-8 lists the mounting kits available for the DM-170 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DM-170 PK-170M RK-170MS-R10 WK-170MS-R10 DIN Mounting Kit - LCD Monitor Arm LCD Monitor Stand ARM-31 STAND-100-RS Table 2-8: DM-170 Mounting Kits Page 48

49 2.5.7 DM-190 Mounting Kits Table 2-9 lists the mounting kits available for the DM-190 monitor. Model Panel Mounting Kit Rack Mounting Kit Wall Mounting Kit DM-190 PK-190M RK-190MS-R10 WK-190MS-R10 DIN Mounting Kit - LCD Monitor Arm ARM-31 LCD Monitor Stand - Table 2-9: DM-190 Mounting Kits 2.6 Mounting Options Each DM series industrial monitor has a number of mounting holes or slots located on the back side of the aluminum frame or on the rear panel for mounting the monitor to a rack, panel, cabinet, DIN rail, wall, arm or stand. The following sections describe the various mounting methods or each model of the DM series industrial monitor Panel Mounting Each model of the DM series industrial monitor has a series of mounting slots located on the top and bottom panel for mounting the monitor to a panel. NOTE: The DM-65 monitor requires two special mounting brackets for installation into a panel. Refer to Section for details. Figure 2-11 shows a typical panel installation. Page 49

50 Figure 2-11: Typical Panel Mounting Table 2-10 lists the number of mounting clamps required to mount the monitor to a panel. Model Mounting Clamps DM DM DM DM DM DM-84 8 Table 2-10: Panel Mounting Clamps Page 50

51 2.6.2 Rack and Cabinet Mounting Each model of the DM series industrial monitor has a series of holes located on the rear of the front panel for mounting the monitor to a rack or cabinet. NOTE: 1. The DM-190 monitor requires two special mounting brackets for installation into a rack or cabinet. Refer to Section for details. 2. The DM-84 monitor uses panel mounting clamps for installation into a rack or cabinet. Refer to Section for details. 3. The DM-65 monitor uses panel mounting clamps for installation into a rack or cabinet. Refer to Section for details. Figure 2-12 shows a typical rack or cabinet installation. Figure 2-12: Typical Rack or Cabinet Mounting Page 51

52 Table 2-11 lists the number of holes each monitor has for mounting to a rack or cabinet. Model Holes DM DM DM DM Table 2-11: Rack Mounting Clamps Wall Mounting Each model of the DM series industrial monitor has four holes located on the rear panel for mounting the monitor to a wall. Figure 2-13 shows the typical methods for wall mounting. Figure 2-13: Typical Wall Mounting Page 52

53 2.6.4 DIN Rail Mounting The DM-84 and DM-65 have four holes located on the rear panel for mounting the monitor to a DIN rail clamp. Figure 2-14 shows a typical DIN rail mounting bracket. Figure 2-14: Typical DIN Rail Mounting Page 53

54 2.6.5 Monitor Arm or Stand Mounting Most models of the DM series industrial monitor have four or eight Video Electronics Standards Association (VESA) standard holes located on the rear panel for mounting the monitor to a monitor arm or stand. NOTE: There is no monitor stand available for the DM-190 monitor. Figure 2-15 shows a typical monitor arm or stand mounting. Figure 2-15: Typical Monitor Arm or Stand Mounting Page 54

55 Chapter 3 3 LCD and Touch Panel Specifications Page 55

56 3.1 LCD Specifications LCD Overview The DM series industrial monitors use the following LCD panels. DM-190: AUO M190EG02 DM-170: AUO M170EG01 DM-150: AUO G150XG01 DM-121: AUO G121SN01 DM-121GX: CHI MEI G121X1-L01 DM-104: Toshiba LTA104D182F DM-084: AUO G084SN03/ Toshiba LTA084C270F DM-65: Toshiba LTA065B0D0F Detailed specifications for the LCD screens are listed in the following sections. Page 56

57 3.1.2 DM-190 LCD Specifications Table 3-1 lists the DM-190 LCD specifications. Model DM-190 Size 19 MFR/Model AUO/M190EG02 Resolution SXGA (1280 x 1024) Active Area (mm) x Pixel Pitch (mm) Mode TN Number of Colors 16.2M Color Saturation (NTSC%) 72 View Angle (H/V) 160 / 160 Brightness (cd/m2) 300 Contrast Ratio 700:1 Response Time (ms) (at 25C) 6 Power Consumption (W) 28 Interface 2ch LVDS Supply Voltage (V) 5 Backlight 4 CCFL Lamp Life (hrs) 50,000 Table 3-1: DM-190 LCD Specifications Page 57

58 3.1.3 DM-170 LCD Specifications Table 3-2 lists the DM-170 LCD specifications. Model DM-170 Size 17 MFR/Model AUO/M170EG01 Resolution SXGA (1280 x 1024) Active Area (mm) x Pixel Pitch (mm) Mode TN Number of Colors 16.2M Color Saturation (NTSC%) 72 View Angle (H/V) 140/130 Brightness (cd/m2) 300 Contrast Ratio 500:1 Response Time (ms) (at 25C) 8 Power Consumption (W) 25.8 Interface 2ch LVDS Supply Voltage (V) 5 Backlight 4 CCFL Lamp Life (hrs) 50,000 Table 3-2: DM-170 LCD Specifications Page 58

59 3.1.4 DM-150 LCD Specifications Table 3-3 lists the DM-150 LCD specifications. Model DM-150 Size 15 MFR/Model AUO/G150XG01 XGA (1024 x Resolution 768) Active Area (mm) x Pixel Pitch (mm) Mode Number of Colors TN 262K Color Saturation (NTSC%) 60 View Angle (H/V) 130/120 Brightness (cd/m2) 350 Contrast Ratio 500:1 Response Time (ms) (at 25C) 12 Power Consumption (W) 11.5 Interface 1ch LVDS Supply Voltage (V) 3.3 Backlight 2 CCFL Lamp Life (hrs) Table 3-3: DM-150 LCD Specifications Page 59

60 3.1.5 DM-121 LCD Specifications Table 3-4 lists the DM-121 LCD specifications. Model DM-121G DM-121GX Size MFR/Model AUO/G121SN01 CHE MEI/G121X1-L01 Resolution SVGA (800 x 600) XGA (1024 x 768) Active Area (mm) x x Pixel Pitch (mm) Mode TN TN Number of Colors 262K 262K View Angle (H/V) 150/ /160 Brightness (cd/m2) Contrast Ratio 500:1 700:1 Response Time (ms) (at 25C) (TR); 12 (TF) Power Consumption (W) Interface 1ch LVDS 1ch LVDS Supply Voltage (V) Backlight 2 CCFL 2 CCFL Lamp Life (hrs) Table 3-4: DM-121 LCD Specifications Page 60

61 3.1.6 DM-104 LCD Specifications Table 3-5 lists the DM-104 LCD specifications. Model DM-104 Size 10.4 MFR/Model Toshiba/LTA104D182F Resolution SVGA (800 x 600) Active Area (mm) x Pixel Pitch (mm) Mode Number of Colors TN 262K View Angle (H/V) 120 / 100 Brightness (cd/m2) 400 Contrast Ratio 500:1 Response Time (ms) (at 25C) Interface 6 (ton), 17 (toff) 1ch LVDS Supply Voltage (V) 3.3 Backlight 2 CCFL Lamp Life (hrs) Table 3-5: DM-104 LCD Specifications Page 61

62 3.1.7 DM-84 LCD Specifications Table 3-6 lists the DM-84 LCD specifications. Model DM-84 Size 8.4 MFR/Model Toshiba/LTA084C270F Resolution SVGA (800 x 600) Active Area (mm) x Pixel Pitch (mm) Mode Number of Colors TN 262K View Angle (H/V) 120 / 100 Brightness (cd/m2) 400 Contrast Ratio 450:1 Response Time (ms) (at 25C) Interface 8 (ton), 17 (toff) 1ch LVDS Supply Voltage (V) 3.3 Backlight 2 CCFL Lamp Life (hrs) Table 3-6: DM-84 LCD Specifications Page 62

63 3.1.8 DM-65 LCD Specifications Table 3-7 lists the DM-65 LCD specifications. Model DM-65 Size 6.5 MFR/Model Toshiba/LTA065B0D0F Resolution VGA (640 x 480) Active Area (mm) x Pixel Pitch (mm) Mode Number of Colors 262K Color Saturation (NTSC%) View Angle (H/V) 140/120 Brightness (cd/m2) 400 Contrast Ratio 500:1 Response Time (ms) (at 25C) 25 Power Consumption (W) 4.2 Interface Supply Voltage (V) 3.3 Backlight 2 CCFL Lamp Life (hrs) Table 3-7: DM-65 LCD Specifications Page 63

64 3.2 Optional Touch Panels IEI offers optional touch panels for the DM series industrial monitors with the following features: Small border customized design All size touch panel design Customized activation force and palm rejection Customized optical characteristics High reliability and durability in the field Touch Panel Models Table 3-8 lists the DM series industrial monitors and their associated touch panels. Model DM-190 Touch Panel PanJit A DM-170 PanJit A DM-150 PanJit B DM-121 PanJit B DM-104 PanJit A DM-84 PanJit B DM-65 PanJit C Table 3-8: Touch Panel Models Page 64

65 3.2.2 Touch Panel Dimensions Table 3-9 shows the touch panel dimensions in millimeters. Model: Dimension Width Length Thick PanJit A Dimensional Outline: Viewing Area: Active Area: Key Area: PanJit A Dimensional Outline: Viewing Area: Active Area: Key Area: PanJit Dimensional Outline: B Viewing Area: Active Area: PanJit Dimensional Outline: B Viewing Area: Active Area: PanJit Dimensional Outline: A Viewing Area: Active Area: Dimensional PanJit B Outline: Viewing Area: Active Area: PanJit C Dimensional Outline: Page 65

66 Viewing Area: Active Area: Table 3-9: Touch Panel Dimensions (mm) Touch Panel Specifications Table 3-10 lists the touch panel specifications. Type Input Method Wire Type Maximum Voltage and Currant Analog Resistive Type Touch Panel Finger, Stylus or gloved hand 5-wire DC7V Position Accuracy Less than 1.5% Isolation Resolution Activation Force 20M ohm 4096 x 4096 dpi based on controller resolution Typical: less than 100g Optional: custom activation force and palm rejection Controller Interface RS-232 or USB 1.1 Light Transmission Anti-glare type: 78% - 90% Temperature (Typical) Operating: -10 C to 60 C Storage: -20 C to 70 C Relative Humidity Operating: 20% to 90%RH Storage: 20% to 90%RH Electrostatic Protection Touch Panel: 30KV (Contact/Air) Controller: 20KV (Contact/Air) Surface Hardness Life (Hitting) Life (Drawing) 3H and above per LIS K5400 More than 10 million for 5-wire touch panel More than 300 K alphabets for 5-wire touch panel Page 66

67 OS Compatibility Windows: XP/XP Embedded Windows 2000 Windows ME Windows 98 SE Windows CE.Net 4.2 (x86 and ARM) WHQL certified Linux: Fedora Core I/II Mandrake 10.0/10.1 RedHat 9.0 Table 3-10: Touch Panel Specifications Page 67

68 3.2.4 Touch Panel RS-232 Controller Specifications Table 3-11 lists the touch panel RS-232 controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.+5V (100mA typical, 50mV peak to peak maximum ripple and noise) Operating Temperature 0 C to 50 C Storage Temperature -40 C to 80 C Relative Humidity 95% at 60 C Interface Bi-directional RS-232 serial communication Protocol No parity, 8 data bits, 1 stop bit, 9600 baud (N,8,1,9600) Resolution Report Rate Response Time Attached Cable 2048x2048 Max. 160 points/sec Max. 35 ms 6 shielded cable with 9-pin D-sub connector Regulatory Approvals FCC-B, CE, Unaffected by EMI from other nearby CRTs and other display devices EMI Panel Resistance Unaffected by environmental EMI 5 wire resistive model: 50 ~ 200 ohm Table 3-11: Touch Panel RS-232 Controller Specifications Page 68

69 3.2.5 Touch Panel USB Controller Specifications Table 3-12 lists the touch panel USB controller specifications. Circuit Board Dimension 20mm x 75mm (0.79inches x 2.95inches)----(5-Wire) Power Requirements D.C.+5V (100mA typical, 50mV peak to peak maximum ripple and noise) Operating Temperature 0 C to 50 C Storage Temperature -40 C to 80 C Relative Humidity 95% at 60 C Interface Protocol USB 1.1 Low Speed No parity, 8 data bits, 1 stop bit, 9600 baud (N,8,1,9600) Resolution Report Rate Response Time Attached Cable 2048x2048 Max. 160 points/sec Max. 35 ms 6 shielded cable with USB-A connector for USB port Regulatory Approvals FCC-B, CE, Unaffected by EMI from other nearby CRTs and other display devices EMI Panel Resistance Unaffected by environmental EMI 5 wire resistive model: 50 ~ 200 ohm Table 3-12: Touch Panel USB Controller Specifications Page 69

70 3.3 Power Adapters Table 3-13 lists the AC/DC power adapter specifications. Model DM-190, DM-170, DM-150, DM-121 DM-104, DM-84, DM-65 Power 45 Watt AC/DC Adapter 25 Watt AC/DC Adapter General Description Universal Input 90 to 264 VAC EMI Meets FCC/CISPR 22 Class B MTBF 165Khrs Limited Power Source Universal Input 90 to 264 VAC EMI Meets FCC/CISPR 22 Class B MTBF 300Khrs Limited Power Source Input Voltage Range VAC VAC Input Frequency Hz Hz Inrush Current 40A max. (Cold Start) 30A max. (Cold Start) Hold-up Time 10mS typical 10mS typical Leakage Current 0.5mA max. 3.5mA max. Short Circuit Protection Over-voltage Protection Continuous Output Power Hi-pot Isolation: Input / Output Continuous Yes 45W max. 4242VDC Continuous Yes 25W max. 4242VDC Table 3-13: Power Adapter Specifications Page 70

71 Chapter 4 4 AD Boards Page 71

72 DM Series Industrial Monitor 4.1 AD Board Overview The DM series industrial monitor AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. There are three AD boards used for the DM series monitors: AV-9350, AV-5350 and AV Refer to Table 1-2 for a listing of DM series monitors and their associated AD board. The following sections describe each AD board in detail. 4.2 AV-9350 AD Board The following sections describe the AV-9350 AD board in detail AV-9350 AD Board Overview Figure 4-1: AV-9350 AD Board Overview AV-9350 AD Board Connectors The AV-9350 AD board has the following connectors onboard: 1 x VGA connector 2 x Debugged port 1 x External OSD and LED Indication connector Page 72

73 1 x TTL output connector 2 x 5V power connector 1 x RS-232 connector The AV-9350 AD board has the following connectors on the board rear panel: 1 x RS-232 connector 1 x VGA connector 1 x 12V DC power connector The locations of the peripheral interface connectors for the AV-9350 AD board are shown in Section A complete list of all the peripheral interface connectors can be seen in Section AV-9350 AD Board Layout Figure 4-2 shows the onboard peripheral connectors and onboard jumpers. Figure 4-2: Connector and Jumper Locations Page 73

74 4.2.4 AV-9350 Peripheral Interface Connectors Table 4-1 shows a list of the peripheral interface connectors on the AV-9350 AD board. Detailed descriptions of these connectors can be found in Section Connector Type Label 5V Power connector 2-pin header CN11, CN12 Debugged Port connector 4-pin header CN3, CN5 External OSD and LED Indication connector 9-pin header CN4 Serial Communications connector 10-pin header COM1 TTL Output connector 40-pin header CN7 VGA connector 10-pin header CN2 Table 4-1: AV-9350 Peripheral Interface Connectors AV-9350 Rear Panel Connectors Table 4-2 lists the rear panel connectors and buttons on the AV-9350 AD board. Detailed descriptions of these connectors and buttons can be found in Section Connector Type Label DC 12V Power connector DC Power Jack J2 Serial connector RS232 connector J1 OSD Function Button Pushbutton JP1 OSD Function Button Pushbutton JP2 OSD Function Button Pushbutton JP3 OSD Function Button Pushbutton JP4 VGA Connector 15-pin VGA connector CN1 Table 4-2: AV-9350 Rear Panel Connectors Page 74

75 4.2.6 AV-9350 Onboard Jumper Table 4-3 lists the onboard jumper. A detailed description of the jumper can be found in Section Jumper Type Label LCD Panel Voltage Select 3-pin header JP5 Table 4-3: AV-9350 Onboard Jumper AV-9350 Internal Peripheral Connectors Internal peripheral connectors on the AV-9350 AD board are only accessible when the board is outside of the monitor. This section has complete descriptions of all the internal, peripheral connectors on the AV-9350 AD board. Page 75

76 V Power Connector CN Label: CN Type: CN11, CN12 2-pin header CN Pinouts: See Table 4-4 CN Location: See Figure 4-3 The 5V power connector is a general-purpose power connector. Pi Descriptio Pi Descriptio n n n n 1 +5V 2 GND Table 4-4: 5V Power Connector Pinouts Figure 4-3: 5V Power Connector Location Page 76

77 4.2.9 Debugged Port Connector CN Label: CN Type: CN3, CN5 4-pin header CN Pinouts: See Table 4-5 CN Location: See Figure 4-4 Use the debugged port connector to update the AD board BIOS. Pi n Description 1 +5V 2 TX 3 RX 4 GND Table 4-5: Debugged Port Connector Pinouts Figure 4-4: Debugged Port Connector Location Page 77

78 External OSD and LED Indication Connector CN Label: CN Type: CN4 9-pin header CN Pinouts: See Table 4-6 CN Location: See Figure 4-5 The External OSD and LED Indication connector connects to an external OSD controller. Pi n Description LED_ORANG 1 E 2 +5V 3 LED_GREEN MENU/ENTE 4 R 5 RIGHT 6 LEFT 7 AUTO 8 LCD ON/OFF 9 GND Table 4-6: External OSD and LED Indication Connector Pinouts Page 78

79 Figure 4-5: External OSD and LED Indication Connector Location Serial Communications Connector CN Label: CN Type: COM1 10-pin header CN Pinouts: See Table 4-7 CN Location: See Figure 4-6 The AV-9350 has a 10-pin serial communications connector. Pi Descriptio Pi Descriptio n n n n 1 DCD 6 CTS 2 DSR 7 DTR 3 RXD 8 RI 4 RTS 9 GND 5 TXD 1 GND 0 Table 4-7: Serial Communications Connector Pinouts Page 79

80 Figure 4-6: Serial Communications Connector Location Page 80

81 TTL Output Connector CN Label: CN Type: CN7 40-pin header CN Pinouts: See Table 4-8 CN Location: See Figure 4-7 The TTL output connector connects the LCD panel to the system. Pi Descriptio Pi Descriptio n n n n 2 LCD5V 1 LCD5V 4 GROUND 3 GROUND 6 LCD3V 5 LCD3V 8 GROUND 7 N/C 1 0 B1 9 B0 1 2 B3 1 1 B2 1 4 B5 1 3 B4 1 6 B7 1 5 B6 1 8 G1 1 7 G0 2 0 G3 1 9 G2 2 2 G5 2 1 G4 2 4 G7 2 3 G6 Page 81

82 2 6 R1 2 5 R0 2 8 R3 2 7 R2 3 0 R5 2 9 R4 3 2 R7 3 1 R6 3 4 GROUND 3 3 GROUND 3 6 FPVS 3 5 FPCLK 3 8 FPHS 3 7 FPDEN 4 0 ENVEE 3 9 N/C Table 4-8: TTL Output Connector Pinouts Figure 4-7: TTL Output Connector Location Page 82

83 NOTE: The supply voltage (3.3V and 5V) can be selected via JP VGA Connector CN Label: CN Type: CN2 10-pin header CN Pinouts: See Table 4-9 CN Location: See Figure 4-8 In addition to the standard DB-15 female VGA connector (CN1), a VGA connection can also be made through the onboard CN2 10-pin header. Pin Description Pin Description 1 RED 2 DDCCLK 3 GREEN 4 DDCDAT 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND Table 4-9: VGA Connector Pinouts Page 83

84 Figure 4-8: VGA Connector Location AV-9350 External (Rear Panel) Connectors Figure 4-9 shows the AV-9350 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices. The peripheral connectors on the rear panel are: 1 x DC 12V connector 1 x Serial Communications connector 4 x OSD Function Button 1 x VGA conector Figure 4-9: AV-9350 External (Rear Panel) Connectors Page 84

85 DC 12V Connector CN Label: CN Type: J2 DC 12V Jack CN Pinouts: See Table 4-10 CN Location: See Figure 4-9 Use the DC 12V connector to power the monitor. PI N DESCRIPTION 1 GND 2 GND 3 DC 12V Table 4-10: DC 12V Connector Pinouts RS232 Serial Connector CN Label: CN Type: J1 D-Sub 9 female connector CN Pinouts: See Table 4-11 and Figure 4-10 CN Location: See Figure 4-9 Use the RS-232 serial connector to connect the touch panel. PI N DESCRIPTION PI N DESCRIPTION 1 DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI/Vout Page 85

86 5 GND Table 4-11: RS232 Serial Connector Pinouts Figure 4-10: RS232 Serial Connector Pinout Locations OSD Control Buttons CN Label: CN Type: JP1, JP2, JP3, JP4 Pushbutton CN Pinouts: See Table 4-12, Table 4-13, Table 4-14, Table 4-15 CN Location: See Figure 4-9 Use these buttons to control the OSD functions. The following tables list each button s function and pinouts. PI N DESCRIPTION PI N DESCRIPTION 1 MENU/SELECT 3 No Connect 2 Ground 4 No Connect Table 4-12: OSD Control Button JP1 Pinouts PI N DESCRIPTION PI N DESCRIPTION 1 UP/COLOR ADJUST 3 No Connect 2 Ground 4 No Connect Table 4-13: OSD Control Button JP2 Pinouts Page 86

87 PI N DESCRIPTION PI N DESCRIPTION DOWN/AUTO 1 ADJUST 3 No Connect 2 Ground 4 No Connect Table 4-14: OSD Control Button JP3 Pinouts PI N DESCRIPTION PI N DESCRIPTION 1 LCD ON/OFF 3 No Connect 2 Ground 4 No Connect Table 4-15: OSD Control Button JP4 Pinouts VGA Connector CN Label: CN Type: CN1 HD-D-sub 15 female connector CN Pinouts: See Table 4-16 and Figure 4-11 CN Location: See Figure 4-9 Use the standard HD-D-sub 15-pin VGA connector to connect the monitor to a system. PIN DESCRIPTION PIN DESCRIPTION 1 Red 9 No Connect 2 Green 10 Ground 3 Blue 11 No Connect 4 No Connect 12 DDC DAT 5 Ground 13 Horizontal Synchronization 6 Ground 14 Vertical Synchronization 7 Ground 15 DDC Clock 8 Ground Page 87

88 Table 4-16: VGA Connector Pinouts Figure 4-11: VGA Connector Pinout Locations AV-9350 Onboard Jumper NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. Figure 4-12: Jumpers The AV-9350 has one onboard jumper (Table 4-3). Page 88

89 Figure 4-13: Jumper Location Page 89

90 LCD Panel (TTL) Voltage Select Jumper Jumper Label: Jumper Type: JP5 3-pin header Jumper Location: See Figure 4-13 Jumper Settings: See Table 4-17 The JP5 jumper sets the voltage to the LCD panel. JP 5 1- Description Panel Voltage select 5V Panel Voltage select 3.3V (Default) Table 4-17: LCD Panel (TTL) Voltage Select Jumper Settings Page 90

91 DM Series Industrial Monitor 4.3 AV-5350 AD Board The following sections describe the AV-5350 AD board in detail AV-5350 AD Board Overview Figure 4-14: AV-5350 AD Board Overview AV-5350 AD Board Connectors The AV-5350 AD board has the following connectors onboard: 1 x VGA connector 1 x External OSD and LED Indication connector 1 x LVDS connector 2 x 5V power connector Page 91

92 1 x 12V power connector 1 x Backlight Inverter connector The AV-5350 AD board has the following connectors on the board rear panel: 1 x VGA connector 1 x 12V DC power connector The locations of the peripheral interface connectors for the AV-5350 AD board are shown in Section A complete list of all the peripheral interface connectors can be seen in Section AV-5350 AD Board Layout Figure 4-15 shows the onboard peripheral connectors and onboard jumpers. Figure 4-15: Connector and Jumper Locations Page 92

93 4.3.4 AV-5350 Peripheral Interface Connectors Table 4-18 shows a list of the peripheral interface connectors on the AV-5350 AD board. Detailed descriptions of these connectors can be found in Section Connector Type Label 5V Power connector 2-pin header CN8, CN9 12V Power connector 2-pin header CN7 Backlight Inverter connector 6-pin header CN6 External OSD and LED Indication connector 9-pin header CN2 LVDS Output connector 30-pin header CN5 VGA connector 10-pin header J2 Table 4-18: AV-5350 Peripheral Interface Connectors AV-5350 Rear Panel Connectors Table 4-19 lists the rear panel connectors and jumpers on the AV-5350 AD board. Detailed descriptions of these connectors and jumpers can be found in Section Connector Type Label DC 12V Power connector DC Power Jack J3 VGA Connector 15-pin VGA connector J1 Table 4-19: AV-5350 Rear Panel Connectors AV-5350 Onboard Jumper Table 4-20 lists the onboard jumper. A detailed description of the jumper can be found in Section Page 93

94 Jumper Type Label LCD Panel Voltage Select 3-pin header JP1 Table 4-20: AV-5350 Onboard Jumper AV-5350 Internal Peripheral Connectors Internal peripheral connectors on the AV-5350 AD board are only accessible when the board is outside of the monitor. This section has complete descriptions of all the internal, peripheral connectors on the AV-5350 AD board V Power Connector CN Label: CN Type: CN8, CN9 2-pin header CN Pinouts: See Table 4-21 CN Location: See Figure 4-16 The 5V power connector is a general-purpose power connector. Pi Descriptio Pi Descriptio n n n n 1 +5V 2 GND Table 4-21: 5V Power Connector Pinouts Page 94

95 Figure 4-16: 5V Power Connector Location V Power Connector CN Label: CN Type: CN7 2-pin header CN Pinouts: See Table 4-22 CN Location: See Figure 4-17 The 12V power connector is a general-purpose power connector. Pi Descriptio Pi Descriptio n n n n 1 +12V 2 GND Table 4-22: 12V Power Connector Pinouts Page 95

96 Figure 4-17: 12V Power Connector Location Backlight Inverter Connector CN Label: CN Type: CN6 6-pin header CN Pinouts: See Table 4-23 CN Location: See Figure 4-18 The Inverter connector connects to the LCD backlight. Pi n Description 1 +12V 2 +12V 3 On/Off 4 BKLT_ADJ 5 GND 6 GND Table 4-23: Backlight Inverter Connector Pinouts Page 96

97 Figure 4-18: Backlight Inverter Connector Location External OSD and LED Indication Connector CN Label: CN Type: CN2 9-pin header CN Pinouts: See Table 4-24 CN Location: See Figure 4-19 The External OSD and LED Indication connector connects to an external OSD controller. Pi n Description 1 LED_ORANGE 2 +5V 3 LED_GREEN 4 MENU/ENTER 5 RIGHT 6 LEFT Page 97

98 7 AUTO 8 LCD ON/OFF 9 GND Table 4-24: External OSD and LED Indication Connector Pinouts Figure 4-19: External OSD and LED Indication Connector Location LVDS Output Connector CN Label: CN Type: CN5 30-pin header CN Pinouts: See Table 4-25 CN Location: See Figure 4-20 Use the LVDS output connector to connect the LCD panel to a system. Pi Descriptio Pi Descriptio n n n n 1 GND 2 GND 3 TXO3+ 4 TXO3-5 TXOC+ 6 TXOC- 7 TXO2+ 8 TXO2-9 TXO1+ 10 TXO1- Page 98

99 11 TXO0+ 12 TXO0-13 GND 14 GND 15 TXE3+ 16 TXE3-17 TXEC+ 18 TXEC- 19 TXE2+ 20 TXE2-21 TXE1+ 22 TXE1-23 TXE0+ 24 TXE0-25 GND 26 GND 27 VDD 28 VDD 29 VDD 30 VDD Table 4-25: LVDS Output Connector Pinouts Figure 4-20: LVDS Output Connector Location NOTE: The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP1. Page 99

100 VGA Connector CN Label: CN Type: J2 10-pin header CN Pinouts: See Table 4-26 CN Location: See Figure 4-21 In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also be made through the onboard CN2 10-pin header. Pi Descriptio Pi Descriptio n n n n 1 RED 2 DDCCLK 3 GREEN 4 DDCDAT 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND Table 4-26: VGA Connector Pinouts Page 100

101 Figure 4-21: VGA Connector Location AV-5350 External (Rear Panel) Connectors Figure 4-22 shows the AV-5350 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices. The peripheral connectors on the rear panel are: 1 x DC 12V connector 1 x VGA connector Figure 4-22: AV-5350 External (Rear Panel) Connectors Page 101

102 DC 12V Connector CN Label: CN Type: J3 DC 12V Jack CN Pinouts: See Table 4-27 CN Location: See Figure 4-22 Use the DC 12V connector to power the monitor. PI N DESCRIPTIO N 1 GND 2 GND 3 DC 12V Table 4-27: DC 12V Connector Pinouts VGA Connector CN Label: CN Type: J1 HD-D-sub 15 female connector CN Pinouts: See Table 4-28 and Figure 4-23 CN Location: Figure 4-22 Use the standard HD-D-sub 15-pin VGA connector to connect the monitor to a system. PIN DESCRIPTION PIN DESCRIPTION 1 Red 9 No Connect 2 Green 10 Ground 3 Blue 11 No Connect 4 No Connect 12 DDC DAT 5 Ground 13 Horizontal Synchronization Page 102

103 PIN DESCRIPTION PIN DESCRIPTION 6 Ground 14 Vertical Synchronization 7 Ground 15 DDC Clock 8 Ground Table 4-28: VGA Connector Pinouts Figure 4-23: VGA Connector Pinout Locations AV-5350 Onboard Jumper NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means removing the plastic clip from a jumper. Figure 4-24: Jumpers The AV-5350 has one onboard jumper (Table 4-20). Page 103

104 Figure 4-25: Jumper Location LCD Panel Voltage Select Jumper Jumper Label: Jumper Type: JP5 6-pin header Jumper Location: See Figure 4-25 Jumper Settings: See Table 4-29 The JP1 jumper sets the voltage to the LCD panel. JP1 Description 1-2 Panel Voltage select 3.3V (Default) 3-4 Panel Voltage select 5V 5-6 Panel Voltage select 12V Table 4-29: LCD Panel Voltage Select Jumper Settings Page 104

105 DM Series Industrial Monitor 4.4 AV-5300 AD Board Overview The AV-5300 AD board provides a wide variety of control interfaces, receiving and managing interface signals from a CPU card through cabling. The following sections describe the AV-5300 AD board in detail. Figure 4-26: AV-5300 AD Board Overview Page 105

106 4.4.1 AV-5300 AD Board Connectors The AV-5300 AD board has the following connectors on-board: 1 x Auto-dimming connector 1 x Debug connector 1 x External OSD and LED Indication connector 1 x Inverter interface connector 1 x LVDS connector 2 x Power output connector 2 x Power input connector 1 x VGA connector The AV-5300 AD board has the following connectors on the board rear panel: 1 x 12V DC power connector 1 x DVI connector 1 x VGA connector The locations of the peripheral interface connectors for the AV-5300 AD board are shown in Section A complete list of all the peripheral interface connectors can be seen in Section Page 106

107 4.4.2 AV-5300 AD Board Layout Figure 4-27 shows the on-board peripheral connectors and on-board jumpers. Figure 4-27: Connector and Jumper Locations Page 107

108 4.4.3 AV-5300 Peripheral Interface Connectors Table 4-30 shows a list of the peripheral interface connectors on the AV-5300 AD board. Detailed descriptions of these connectors can be found in Section Connector Type Label Auto-dimming connector 6-pin wafer connector CN16 Debug connector 4-pin wafer connector CN4 External OSD and LED Indication connector 9-pin wafer connector CN3 Inverter interface connector 6-pin wafer connector CN2 LVDS connector 30-pin connector CN8 Power output connectors 2-pin wafer connector CN12, CN13 Power input connectors 3-pin wafer connector CN24. CN25 VGA connector 10-pin box header J1 Table 4-30: AV-5300 Peripheral Interface Connectors AV-5300 Rear Panel Connectors Table 4-31 lists the rear panel connectors on the AV-5300 AD board. Detailed descriptions of these connectors can be found in Section Connector Type Label 12V DC power connector DC Power Jack J3 DVI connector 24-pin DVI-D connector J2 VGA connector 15-pin VGA connector J5 Table 4-31: AV-5300 Rear Panel Connectors Page 108

109 4.4.5 AV-5300 On-board Jumpers Table 4-32 lists the on-board jumpers. A detailed description of these jumpers can be found in Section Jumper Type Label LCD Panel Power Input Select 6-pin header JP4 LCD Panel Voltage Select 6-pin header JP1 Table 4-32: AV-5300 On-board Jumpers AV-5300 Internal Peripheral Connectors Internal peripheral connectors on the AV-5300 AD board are only accessible when the board is outside of the monitor. This section has complete descriptions of all the internal, peripheral connectors on the AV-5300 AD board Auto-Dimming Connector CN Label: CN Type: CN16 6-pin wafer connector CN Pinouts: See Table 4-33 CN Location: See Figure 4-28 The auto-dimming connector connects to an external auto-dimming sensor. PIN DESCRIPTION V 2 NC 3 GND 4 SCL 5 NC 6 SDA Page 109

110 Table 4-33: Auto-dimming Connector Pinouts Figure 4-28: Auto-dimming Connector Location Debug Port Connector CN Label: CN Type: CN4 4-pin wafer connector CN Pinouts: See Table 4-34 CN Location: See Figure 4-29 Use the debug port connector to update the AD board BIOS. PIN DESCRIPTION 1 +5V 2 TX 3 RX 4 GND Table 4-34: Debug Port Connector Pinouts Page 110

111 Figure 4-29: Debug Port Connector Location External OSD and LED Indication Connector CN Label: CN Type: CN3 9-pin wafer connector CN Pinouts: See Table 4-35 CN Location: See Figure 4-30 The External OSD and LED Indication connector connects to an external OSD controller. PIN DESCRIPTION 1 LED_ORANGE 2 LED_SENSOR 3 LED_GREEN 4 MENU/ENTER 5 RIGHT 6 LEFT 7 AUTO/EXIT 8 LCD ON/OFF 9 GND Table 4-35: External OSD and LED Indication Connector Pinouts Page 111

112 Figure 4-30: External OSD and LED Indication Connector Location Backlight Inverter Connector CN Label: CN Type: CN2 6-pin wafer connector CN Pinouts: See Table 4-36 CN Location: See Figure 4-31 The Inverter connector connects to the LCD backlight. Using the BKLT_EN signal to control the inverter status (ON/OFF) and the BKLT_ADJ signal to adjust brightness of inverter by OSD brightness function. The OSD brightness function can control a PWM input and variable DC voltage to minimize flickering (due to the interference between panel timing and inverter s AC timing), and adjust LCD back light brightness. PIN DESCRIPTION 1 +12V 2 +12V 3 BKLT_EN 4 BKLT_ADJ 5 GND 6 GND Table 4-36: Backlight Inverter Connector Pinouts Page 112

113 Figure 4-31: Backlight Inverter Connector Location LVDS Output Connector CN Label: CN Type: CN8 30-pin connector CN Pinouts: See Table 4-37 CN Location: See Figure 4-32 Use either LVDS output connector to connect the LCD panel to a system. PIN DESCRIPTION PIN DESCRIPTION 1 GND 2 GND 3 TXO3+ 4 TXO3-5 TXOC+ 6 TXOC- 7 TXO2+ 8 TXO2-9 TXO1+ 10 TXO1-11 TXO0+ 12 TXO0-13 GND 14 GND 15 TXE3+ 16 TXE3-17 TXEC+ 18 TXEC- 19 TXE2+ 20 TXE2-21 TXE1+ 22 TXE1- Page 113

114 PIN DESCRIPTION PIN DESCRIPTION 23 TXE0+ 24 TXE0-25 GND 26 GND 27 VDD 28 VDD 29 VDD 30 VDD Table 4-37: LVDS Output Connector Pinouts Figure 4-32: LVDS Output Connector Location NOTE: The supply voltage (3.3V (Default), 5V or 12V) can be selected via JP Power Output Connector CN Label: CN Type: CN12, CN13 2-pin wafer connector CN Pinouts: See Table 4-38 and Table 4-39 CN Location: See Figure 4-33 Page 114

115 The AV-5300 supports two power output connectors, one for 12V and the other for 5V. PIN DESCRIPTION 1 +12V 2 GND Table 4-38: Power Output Connector Pinouts (CN12) PIN DESCRIPTION 1 +5V 2 GND Table 4-39: Power Output Connector Pinouts (CN13) Figure 4-33: Power Output Connector Locations Power Input Connector CN Label: CN Type: CN24, CN25 2-pin wafer connector, 3-pin wafer connector CN Pinouts: See Table 4-40 and Table 4-41 CN Location: See Figure 4-34 Page 115

116 The AV-5300 supports two internal power input connectors. PIN DESCRIPTION 1 +12V 2 GND Table 4-40: Power Input Connector Pinouts (CN24) PIN DESCRIPTION 1 +12V Input 2 GND 3 +9V~36V to external power module Table 4-41: Power Input Connector Pinouts (CN25) Figure 4-34: Power Input Connector Locations Page 116

117 VGA Connector CN Label: CN Type: J1 10-pin box header CN Pinouts: See Table 4-42 CN Location: See Figure 4-35 In addition to the standard DB-15 female VGA connector (J1), a VGA connection can also be made through the on-board CN2 10-pin header. PIN DESCRIPTION PIN DESCRIPTION 1 RED 2 SMCLK 3 GREEN 4 SMDATA 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND Table 4-42: VGA Connector Pinouts Figure 4-35: VGA Connector Location Page 117

118 AV-5300 On-board Jumpers NOTE: A jumper is a metal bridge used to close an electrical circuit. It consists of two or three metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To CLOSE/SHORT a jumper means connecting the pins of the jumper with the plastic clip and to OPEN a jumper means Figure 4-36: Jumpers removing the plastic clip from a jumper. The AV-5300 has two on-board jumpers (Table 4-32). Figure 4-37: Jumper Locations Page 118

119 LCD Panel Power Input Jumper Jumper Label: Jumper Type: JP4 6-pin header Jumper Location: See Figure 4-37 Jumper Settings: See Table 4-43 The JP4 jumper sets the input source from either the 12V power connector (J3) or the external terminal block. JP4 Description 1-3, V from power connector (J3) (Default) 3-5, 4-6 Input with external connector (Need external power module) Table 4-43: LCD Panel Power Input Jumper Settings LCD Panel Voltage Select Jumper Jumper Label: Jumper Type: JP1 6-pin header Jumper Location: See Figure 4-37 Jumper Settings: See Table 4-44 The JP1 jumper sets the voltage to the LCD panel. JP1 Description 1-2 Panel Voltage select 3.3V (Default) 3-4 Panel Voltage select 5V 5-6 Panel Voltage select 12V Table 4-44: LCD Panel Voltage Select Jumper Settings Page 119

120 AV-5300 External (Rear Panel) Connectors Figure 4-38 shows the AV-5300 external (rear panel) connectors. The peripheral connectors on the back panel of the monitor can connect to external devices. The peripheral connectors on the rear panel are: 1 x DC 12V connector 1 x DVI-D connector 1 x VGA connector Figure 4-38: AV-5300 External (Rear Panel) Connectors DC 12V Connector CN Label: CN Type: J3 DC 12V Jack CN Pinouts: See Table 4-45 CN Location: See Figure 4-38 Use the DC 12V connector to power the monitor. PIN DESCRIPTION 1 GND 2 GND 3 DC 12V Table 4-45: DC 12V Connector Pinouts Page 120

121 VGA Connector CN Label: CN Type: J5 D-sub 15 female connector CN Pinouts: See Table 4-46 and Figure 4-39 CN Location: See Figure 4-38 Use the standard D-sub 15-pin VGA connector to connect the monitor to a system. PIN DESCRIPTION PIN DESCRIPTION 1 Red 9 No Connect 2 Green 10 Ground 3 Blue 11 No Connect 4 No Connect 12 DDC DAT 5 Ground 13 Horizontal Synchronization 6 Ground 14 Vertical Synchronization 7 Ground 15 DDC Clock 8 Ground Table 4-46: VGA Connector Pinouts Figure 4-39: VGA Connector Pinout Locations Page 121

122 DVI-D Connector CN Label: CN Type: J2 D-sub DVI female connector CN Pinouts: See Table 4-47 and Figure 4-40 CN Location: See Figure 4-38 The 24-pin female dual link digital only DVI [Digital Visual Interface] connector is a standard for high-speed, high-resolution digital displays. Use the DVI-D connector to connect the LCD to a system. PIN DESCRIPTION PIN DESCRIPTION 1 RX2-2 RX2+ 3 GND 4 NC 5 NC 6 DVI-SCL 7 DVI-SDA 8 NC 9 RX1-10 RX1+ 11 GND 12 NC 13 NC 14 DVI-5V 15 GND 16 HOT-PLUG 17 RX0-18 RX0+ 19 GND 20 NC 21 NC 22 GND 23 RXC+ 24 RXC- Table 4-47: DVI-D Connector Pinouts Figure 4-40: DVI-D Connector Pinout Locations Page 122

123 Chapter 45 5 Installation Page 123

124 5.1 Installation Precautions When installing the DM series industrial monitor, please follow the precautions listed below: Read the user manual: The user manual provides a complete description of the DM series industrial monitor, installation instructions and configuration options. DANGER! Disconnect Power: Power to the monitor must be disconnected when installing the DM series industrial monitor, or before any attempt is made to access the rear panel. Electric shock and personal injury might occur if the rear panel of the monitor is opened while the power cord is still connected to an electrical outlet. Qualified Personnel: The DM series industrial monitor must be installed and operated only by trained and qualified personnel. Maintenance, upgrades, or repairs may only be carried out by qualified personnel who are familiar with the associated dangers. Mounting: Since the monitor may weigh up to 10 kg (not including a swing arm or other accessories), please ensure at least two people assist with mounting the monitor. Air Circulation: Make sure there is sufficient air circulation when installing the monitor. The monitor s cooling vents must not be obstructed by any objects. Blocking the vents can cause overheating of the monitor. Leave at least 5 cm of clearance around the monitor to prevent overheating. Grounding: The monitor should be properly grounded. The voltage feeds must not be overloaded. Adjust the cabling and provide external overcharge protection per the electrical values indicated on the label attached to the back of the monitor. Anti-static Discharge: The rear panel of the monitor must to be removed to configure the monitor s AD board voltage select jumper. When doing so, be sure the monitor is disconnected from its power source and take all necessary safety precautions to avoid electrocution and static discharge to the AD board. The use of a grounded wrist strap and an anti-static work pad is recommended. Page 124

125 5.2 Unpacking Packaging When shipped, the DM series industrial monitor is wrapped in a plastic bag. Two polystyrene ends are placed on either side of the monitor. The monitor is then placed into a first (internal) cardboard box. This box is then sealed and placed into a second (external) cardboard box. The second box is also sealed. A bag containing accessory items is placed underneath the monitor, at the bottom of the internal (first) box Unpacking Procedure To unpack the DM series industrial monitor, follow the steps below: WARNING: The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the DM series industrial monitor has been properly installed. This ensures the screen is protected during the installation process. Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box. Step 2: Open the external (second) box. Step 3: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the internal (first) box. Step 4: Lift the monitor out of the boxes. Step 5: Remove both polystyrene ends, one from each side. Step 6: Pull the plastic cover off the DM series industrial monitor. Page 125

126 Step 7: Make sure all the components listed in the packing list are present. Step 0: Packing List All the monitors in the DM series are shipped with the following components: 1 x DM-190/170/150/121/104/84/65 series industrial monitor. 1 x AC Power cable 1 x VGA Cable 1 x 45W AC Power Adapter (DM-190 / 170 / 150 / 121) 1 x 25W AC Power Adapter (DM-104 / 84 / 65) 5 x Replacement Round Head Screw 5 x Replacement Flat Head Screw 5 x Replacement Wire Strain Band 1 x User Manual on CDROM 1 x Power Cable for Terminal Block (Optional for M model) 1 x Touch Panel RS-232 Cable / Touch Pen / Driver CDROM (Optional for T-R model) 1 x Touch Panel USB Cable / Touch Pen / Driver CDROM (Optional for USB/T-R model) If any of these items are missing or damaged, contact the distributor or sales representative immediately. 5.3 Pre-installation Preparation Tools Before installing the DM series industrial monitor, make sure the following tools are on hand: Philips (crosshead) screwdriver: All the retention screws on the system are Philips screws. Soft working mat: When the DM series industrial monitor is installed, the screen is placed on the working surface. It is therefore important to rest the MPC indutrial workstation on a soft at that cannot damage the LCD screen on the front of the DM series industrial monitor. Page 126

127 5.3.2 Voltage Select Jumper Settings If the monitor comes with both 12V and 9~36V DC power connectors, the voltage select jumper on the integrated AD board must be configured for the DC connector that is used to power the monitor. Refer to Chapter 4 for the appropriate jumper settings of each AD board. NOTE: The default voltage select jumper is configured for a 12V power source. Do not change the jumper setting unless a 9~36V DC power connector is present on the rear panel and is to be used as the monitor s power source. To properly set the voltage select jumper, the following steps must be completed: Step 1: Use a screwdriver to remove all the screws holding the rear panel to the monitor. Step 2: Remove the rear panel. Step 3: Locate the voltage select jumper. (See Chapter 4) Step 4: Use the jumper(s) to set the correct voltage input. (See Chapter 4) Step 5: Replace the rear panel. Step 6: Replace all removed screws.step 0: Page 127

128 5.4 Connectors Table 5-1 lists the rear panel connectors for the DM series industrial monitors. DM-65 DM-84 DM-104 DM-121 DM-150 DM-170 DM-190 VGA Yes Yes Yes Yes Yes Yes Yes DVI-D Yes Yes Yes Yes Power (12V Jack) Yes Yes Yes Yes Yes Yes Yes Power (9~36V) (Optional) Touch Panel (Optional) - Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Table 5-1: Rear Panel Connectors Page 128

129 5.4.1 Rear Panel Connectors Overview Figure 5-1: Monitor Rear Panel Connections Figure 5-1 shows all the possible rear panel connectors for the DM series industrial monitor. Refer to Table 5-1 for a list of the monitors and their corresponding connectors. The following sections fully describe the rear panel connectors for the DM series industrial monitor VGA Connector Use the rear panel standard 15-pin female VGA connector to connect the monitor to the system graphics interface. PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION 1 RED 6 GROUND 11 NC 2 GREEN 7 GROUND 12 DDCDAT 3 BLUE 8 GROUND 13 HSYNC 4 NC 9 NC 14 VSYNC 5 GROUND 10 GROUND 15 DDCCLK Page 129

130 Table 5-2: VGA Connector Pinouts Figure 5-2: VGA Connector DVI-D Connector Use the rear panel standard 24-pin female DVI-D connector to connect the monitor to the system graphics interface. PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION 1 TMDS Data2-9 TMDS Data1-17 TMDS Data0-2 TMDS Data2+ 10 TMDS Data1+ 18 TMDSData0+ 3 TMDS Data2/4 Shield 11 TMDS Data1/3 Shield 19 TMDS Data0/5 Shield 4 TMDS Data4-12 TMDS Data3-20 TMDS Data5-5 TMDS Data4+ 13 TMDS Data3+ 21 TMDS Data5+ 6 DDC Clock [SCL] V Power 22 TMDS Clock Shield 7 DDC Data [SDA] 15 Ground (for +5 V) 23 TMDS Clock + 8 Analog vertical sync 16 Hot Plug Detect 24 TMDS Clock - Table 5-3: DVI-D Connector Pinouts Figure 5-3: DVI-D Connector V Power Connector Use the rear panel +12V DC jack to connect the monitor to a power source. Page 130

131 Figure 5-4: 12V Power Connector Optional DC Power Connector Use the rear panel 3-pin terminal block DC power connector to connect the monitor to a DC power source. Figure 5-5: DC Power Connector Optional RS-232 Touch Panel Connector Use the rear panel standard RS-232 DB-9 female touch panel connector to connect the monitor to the system graphics interface. PIN DESCRIPTION PIN DESCRIPTION 1 DCD1 6 CTS1 2 DSR1 7 DTR1 3 RX1 8 RI1 4 RTS1 9 GND 5 TX1 Table 5-4: Optional RS-232 Touch Panel Connector Pinouts Page 131

132 Figure 5-6: Optional RS-232 Touch Panel Connector Optional USB Touch Panel Connector Use the rear panel standard USB touch panel connector to connect the monitor to the system graphics interface. PIN DESCRIPTION PIN DESCRIPTION 1 DCD1 6 CTS1 2 DSR1 7 DTR1 3 RX1 8 RI1 4 RTS1 9 GND 5 TX1 Table 5-5: Optional USB Touch Panel Connector Pinouts Figure 5-7: Optional USB Touch Panel Connector Page 132

133 5.5 Mounting the DM Series Industrial Monitor The DM series industrial monitor can be mounted in a panel, cabinet, rack, DIN rail or wall. The monitor can also be mounted on a monitor arm or stand. The mounting methods are described below. CAUTION: When mounting the monitor take care to tighten the retention screws or bolts until fully secure, but do not over tighten. Over tightening the retention screws or bolts may cause them to become stripped, rendering them useless Panel Mounting Standard Panel Mounting The standard panel mounting procedure applies to the following DM series industrial monitors: DM-190 DM-170 DM-150 DM-121 DM-104 DM-84 To mount the DM series industrial monitor into a panel, please follow the steps below. Step 1: Select the position on the panel to mount the monitor. Step 2: Cut out a section of the panel that corresponds to the rear panel dimensions of the monitor. Take care that the panel section that is cut out is smaller than the overall size of the metal frame that surrounds the monitor but just large enough for the rear panel of the monitor to fit through (Figure 5-8). Page 133

134 Figure 5-8: Panel Opening Step 3: Slide the monitor through the hole until the metal frame is flush against the panel (Figure 5-9). Figure 5-9: Insert the Monitor Step 4: Insert the panel mounting clamps into the pre-formed holes along the edges of the monitor, behind the metal frame. Refer to the mounting kit packing list for the Page 134

135 required number of mounting clamps. Figure 5-10: Panel Mounting Clamp Position Step 5: Tighten the screws that pass through the panel mounting clamps until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-10).Step 3: DM-65 Panel Mounting To mount the DM-65 monitor into a panel, follow steps one through three of the standard panel mounting procedure (Section ), then continue using the steps below. Step 4: Secure the panel mounting clips to either side of the monitor using the retention screws supplied in the mounting kit pack (Figure 5-11). Page 135

136 Figure 5-11: DM-65 Panel Mounting Step 5: Tighten the panel retention screws that pass through the panel mounting clips until the plastic caps at the front of all the screws are firmly secured to the panel (Figure 5-11).Step 0: Cabinet and Rack Installation Standard Cabinet and Rack Installation The standard cabinet/rack mounting procedure applies to the following DM series industrial monitors: DM-170 DM-150 DM-121 DM-104 To mount the DM series industrial monitor into a cabinet/rack, please follow the steps below. Step 1: The back of the metal frame surrounding the DM series industrial monitor has several retention screw holes for a cabinet/rack installation bracket. Page 136

137 NOTE: When purchasing a cabinet/rack installation bracket, make sure it is compatible with both the monitor and the cabinet/rack into which the monitor is installed. Step 2: Slide the monitor through the cabinet/rack bracket until the rear side of the monitor frame is flush against the front of the bracket. Step 3: Make sure the retention screw holes at the rear of the monitor frame are aligned with the retention screw holes in the cabinet/rack bracket. Step 4: Secure the cabinet/rack bracket to the monitor by inserting and tightening the retention screws (Figure 5-12). Figure 5-12: Secure the Cabinet/Rack Bracket Step 5: Slide the monitor with the attached cabinet/rack bracket into a rack or cabinet Page 137

138 (Figure 5-13). Figure 5-13: Install into a Cabinet/Rack Step 6: Once the monitor with the attached cabinet/rack has been properly inserted into the rack or cabinet, secure the front of the rack/cabinet bracket to the front of the rack or cabinet (Figure 5-13). Step 0: Page 138

139 DM-190 Cabinet and Rack Installation To mount the DM-190 monitor into a cabinet/rack, please follow the steps below. Step 1: Insert and tighten the supplied mounting nuts and bolts to the rack for the rack mounting bracket. Each bracket requires three nuts and bolts for installation. (See Figure 5-14) Figure 5-14: Rack Mounting Nuts and Bolts Installation (DM-190) Step 2: Secure the rack mounting bracket to two sides of the monitor using the supplied retention screws. Each bracket requires four screws. (See Figure 5-15) Page 139

140 Figure 5-15: Rack Mounting Bracket Installation (DM-190) Step 3: Carefully insert the slotted holes of the brackets on the monitor through the bolts on the rack and gently pull the monitor downwards until the bolts rests securely in the slotted holes. (See Figure 5-16). Ensure that all six of the bolts fit snuggly into their respective slotted holes.step 0: Page 140

141 Figure 5-16: Rack Mounting (DM-190) DM-84 and DM-65 Cabinet and Rack Installation Use the standard panel mounting procedure (Section ) to mount the DM-84 monitor into a cabinet/rack and use the DM-65 panel mounting procedure (Section ) to mount the DM-65 monitor into a cabinet/rack. Page 141

142 5.5.3 DIN Rail Installation To mount the DM series industrial monitor onto a DIN rail, please follow the steps below. Step 1: Attach the DIN rail mounting bracket to the rear of the monitor. Secure the bracket to the monitor with the supplied retention screws (Figure 5-17). Figure 5-17: DIN Rail Mounting Bracket Step 2: Make sure the inserted screw in the center of the bracket is at the lowest position of the elongated hole (Figure 5-18). Figure 5-18: Screw Locations Page 142

143 Step 3: Place the DIN rail flush against the back of the mounting bracket making sure the edges of the rail are between the upper and lower clamps (Figure 5-19). Figure 5-19: Mounting the DIN RAIL Step 4: Secure the DIN rail to the mounting bracket by turning the top screw clockwise. This draws the lower clamp up and secures the monitor to the DIN rail (Figure 5-20).Step 0: Figure 5-20: Secure the Assembly to the DIN Rail Page 143

144 5.5.4 Wall Mounting CAUTION: Due to safety concerns, it is highly recommended to use the VESA mounting kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit is purchased separately, please make sure the mounting kit is UL-listed. To mount the DM series industrial monitor onto a wall, please follow the steps below. Step 1: Select a location on the wall for the wall-mounting bracket. Step 2: Carefully mark the locations of the four bracket screw holes on the wall. Step 3: Drill four pilot holes at the marked locations on the wall for the bracket retention screws. Step 4: Align the wall-mounting bracket screw holes with the pilot holes. Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes and tightening them (Figure 5-21). Figure 5-21: Wall-mounting Bracket Step 6: Insert the four monitor mounting screws (M4 screws) provided in the wall Page 144

145 mounting kit into the four screw holes on the real panel of the monitor and tighten until the screw shank is secured against the rear panel (Figure 5-22). Figure 5-22: Monitor Support Screws Step 7: Align the mounting screws on the monitor rear panel with the mounting holes on the bracket. Step 8: Carefully insert the screws through the holes and gently pull the monitor downwards until the monitor rests securely in the slotted holes (Figure 5-23). Ensure that all four of the mounting screws fit snuggly into their respective slotted holes.step 0: NOTE: In the diagram below the bracket is already installed on the wall. Page 145

146 Figure 5-23: Wall Mounting the Monitor Monitor Stand Installation The DM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-24). Page 146

147 Figure 5-24: VESA Mounting Holes The monitor stand mounting plate has a matching VESA hole pattern. To mount the DM series industrial monitor onto a stand, please follow the steps below. Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the monitor stand mounting plate. Step 2: Secure the monitor to the stand with the supplied retention screws (Figure 5-25).Step 0: Page 147

148 Figure 5-25: Monitor Stand Mounting Monitor Arm Installation The DM series industrial monitor has Video Electronics Standards Association (VESA) standard mounting holes tapped into the rear panel. The standard holes are M4 set at 100m x 100mm apart (Figure 5-24). The monitor arm mounting plate has a matching VESA hole pattern. To mount the DM series industrial monitor onto a monitor arm, please follow the steps below. Step 1: Line up the threaded holes on the monitor rear panel with the screw holes on the monitor arm mounting plate. Step 2: Secure the monitor to the arm with the supplied retention screws (Figure 5-26). Step 0: Page 148

149 Figure 5-26: Monitor Arm Mounting Page 149

150 THIS PAGE IS INTENTIONALLY LEFT BLANK Page 150

151 Chapter 6 6 On-Screen-Display (OSD) Controls Page 151

152 6.1 User Mode OSD Structure OSD Buttons There are several on-screen-display (OSD) control buttons oriented either vertically along the right hand side or horizontally along the bottom of the monitor front panel. Refer to Section 2.2 for availability and orientation of the OSD controls on specific DM series monitors. Figure 6-1 shows a typical arrangement of OSD controls for all models of the DM series industrial monitor except the DM-65. Figure 6-1: OSD Control Buttons for All Models Except DM-65 Page 152

153 Figure 6-2 shows the OSD controls for the DM-65. Figure 6-2: DM-65 OSD Control Buttons NOTE: Pressing the direction keys (LEFT or RIGHT) can bring out a simple menu which adjusts the LCD screen brightness and contrast values OSD Menu Structure All Models Except DM-65 Table 6-1 shows the OSD menu structure for all models of the DN series industrial monitor except the DM-65. Level 0 Level 1 Value Main Display Features Menu Brightness 0 to 100 Contrast 0 to 100 Horizontal Size 0 to 100 Phase 0 to 100 H. Position 0 to 100 V. Position 0 to 100 Page 153

154 Level 0 Level 1 Value Sharpness 1 to 5 Speaker Volume Mute This menu is currently disabled, and will be implemented with models equipped with speakers. Color Menu Preset NTSC value Preset NTSC value User RGB values from 0 to 100 Language Menu OSD Menu English French German Spanish Italian Japanese Russian Traditional Chinese Simplified Chinese OSD Time Out Select 0 to 60 sec OSD Position 1 to 5 OSD Transparency 0 to 100 Auto Setting Recall On or Off No or Yes Aspect Ratio 4:3 or 5:4 Signal Menu Backlight Menu Digital Analog Light Enable Select On or Off Light Contrast 0 to 100 Light Brightness 0 to 100 Light H Start 0 to 100 Light H Width 0 to 100 Light V Start 0 to 100 Light V Height 0 to 100 Table 6-1: OSD Menus All Models Except DM-65 Page 154

155 Page 155

156 6.1.3 DM-65 OSD Menu Structure Table 6-2 shows the OSD menu structure for the DM-65. Level 0 Level 1 Level 2 Contrast 0 to 100 Brightness 0 to 255 Red Color Adjust Green Blue Color Color Temp 5800 srgb USER Back Clock 0 to 100 Phase 0 to 63 Image Seeting Gamma Sharpness Back H Position 0 to 200 Position V Position 0 to 23 Back OSD H.POS 0 to 200 OSD Menu OSD H.POS 0 to 200 OSD Timer 0 to 27 Language Menu Back English French German Spanish Traditional Chinese Select Page 156

157 Level 0 Level 1 Level 2 Simplified Chinese Japanese Signal source D-SUB Reset Misc. Factory Mode Info. Back Exit Table 6-2: DM-65 OSD Menus 6.2 Using the OSD OSD menu options are described below. NOTE: The DM-65 OSD display features differ from those described below. Use the following display features as reference for the DM-65 monitor Main Display Features Main display features are shown in Figure 6-3. Page 157

158 Figure 6-3: Main Display Features Page 158

159 Brightness: The brightness option adjusts the brightness of screen. This function adjusts the offset value of ADC. Setting this value too high or too low will affect the quality of image. Contrast: This function adjusts the gain value of ADC. Adjusting this value too high or too low will worsen the quality of image. Horizontal Size: This item adjusts the screen size in the horizontal direction. Phase: This option adjusts the input signal and dot clock position (Analog only). H. Position: Adjusts the horizontal position of the display screen. V. Position: Adjusts the vertical position of the display screen. Sharpness: Adjusts the sharpness level to one of the 5 preset values. This option may help reducing the softening edges around displayed objects Color Color options are shown in Figure 6-4. Page 159

160 Figure 6-4: Color Options The Color menu fine-tunes the palette of color hues for the LCD. 9300: NTSC standard Kelvin 7500: NTSC standard Kelvin User: This item allows fine-tuning the balance among Red, Green, and Blue color hues if images look garish or unrealistic Language The Languages are shown in Figure 6-5. Figure 6-5: Language Menu This menu provides options for selecting ODS screen legends in a preferred language. Page 160

161 6.2.4 OSD Configurations The OSD configurations are shown in Figure 6-6. Figure 6-6: OSD Configurations Menu OSD Configurations are described below. OSD Time Out: Determines how many seconds the OSD screen stays on screen before it disappears when OSD is left unattended. OSD Position: Adjusts the OSD position on the screen. Position 1 is in the upper left of the screen, position 2 in the upper right and position 3 in the center. OSD Transparency Determines the opacity of OSD background. Auto Setting This function automatically adjusts the LCD screen position in situations such as connecting the LCD to a different host computer. Recall Restores the default OSD settings. Note that this will restore all default display settings. Aspect Ratio Page 161

162 Adjusts the display ratio referring to the width of the screen and then to the height of the screen Signal The Signal menu in Figure 6-7 enables manual selection of the type of graphic source input, i.e., analog (15-pin VGA) or digital (DVI-D). Figure 6-7: Signal Menu Backlight The Backlight menu in Figure 6-8 enables users to configure the LCD backlight. Page 162

163 Figure 6-8: Backlight Menu Backlight Menu options are described below. Light Enabled: Turns backlight on or off. Light Contrast: Adjusts the backlight contrast. Light Brightness: Adjusts the backlight brightness. Light H Start: Adjusts the backlight projection area in the horizontal direction. Light H Width: Adjusts the width of the backlight projection area. Light V Start: Adjusts the backlight projection area in the vertical direction. Light V Height: Adjusts the height of the backlight projection area. Page 163

164 THIS PAGE IS INTENTIONALLY LEFT BLANK Page 164

165 Chapter 7 7 Software Drivers Page 165

166 7.1 Introduction The touch panel controller enables analog resistive touch panels for four-wire, five-wire & eight-wire models. The controller directly communicates with the PC system through the touch panel communications interface. The controller design is superior in sensitivity, accuracy, and friendly operation. The touch panel driver emulates the left mouse button and the right mouse button functions. The touch panel driver supports the following operating systems: Microsoft Windows versions: o Microsoft Windows 95 o Microsoft Windows 98 o Microsoft Windows ME o Microsoft Windows 2000 o Microsoft Windows NT o Microsoft Windows XP o Microsoft Windows XP Tablet PC Edition Microsoft Windows CE versions: o Microsoft Windows CE 2.12 o Microsoft Windows CE 3.0 o Microsoft Windows CE. NET Linux IMac DOS. Driver installation is described below. 7.2 Driver Installation To install the touch panel software driver, please follow the steps below. Step 1: Insert the driver CD that came with the DM series industrial monitor into the CD drive. Step 2: Once the CD drive is installed, the screen in Figure 7-1 appears. Page 166

167 Figure 7-1: Driver CD Pop Up Screen Step 3: Select the operating system installed on the system from the menu on the left side of the screen. NOTE: The following description is for driver installation using a Windows 2000 OS. If a different OS is installed, please refer to the driver user manual for the relevant OS. The driver user manuals can be accessed by selecting User Manual from the menu on the left side of the Driver CD Pop Up Screen. Step 4: Once the OS system is selected, the touch kit setup will prepare the install shield wizard (Figure 7-2). Page 167

168 Figure 7-2: Install Shield Wizard Preparation Step 5: After the Install Shield Wizard is ready, a welcome screen appears (Figure 7-3). Figure 7-3: Welcome Screen Step 6: To continue the installation process click NEXT. Step 7: An Install PS/2 interface driver screen appears (Figure 7-4). It is not necessary to install the PS/2 interface driver. To continue click NEXT. Page 168

169 Figure 7-4: Install PS/2 Interface Driver Step 8: Four point calibration options are then selected. Four point calibrations can be done every time a user boots up, during the next time the system boots or never. Select if and when a four-point calibration should be done. Click NEXT to continue. Page 169

170 Figure 7-5: Install PS/2 Interface Driver Step 9: The user is then prompted to ensure the touch monitor or the USB for the touch controller is plugged into the system (Figure 7-6). Once the touch controller is plugged into the system, click OK. Figure 7-6: Touch Monitor/USB Touch Controller Confirmation Step 10: The user is then prompted to select a file directory in which the touch kit controller is installed (Figure 7-7). The default directory is C:\Program Files\TouchKit. If a different folder must be used, select browse and then select the folder. Once the folder is selected, click NEXT to continue. Page 170

171 Figure 7-7: Controller Installation Directory Step 11: The user is then prompted to select a file directory in which the program icons are saved (Figure 7-8). The default folder is TouchKit. If a different folder must be used, select a folder from the list shown. Once the folder is selected, click NEXT to continue. Page 171

172 Figure 7-8: Program Icon Directory Step 12: The program then starts installing (Figure 7-9). Page 172

173 Figure 7-9: Installing Step 13: Once the program is finished installing, the user is prompted to restart the computer now or to restart the computer later (Figure 7-10). Select when the computer should be restarted and click FINISH to complete the driver installation procedure.step 0: Figure 7-10: Installation Complete 7.3 Touch Panel Driver Configuration To configure the touch panel driver options, refer to the TouchKit user manual located on the driver installation CD. Page 173

174 THIS PAGE IS INTENTIONALLY LEFT BLANK Page 174

175 Chapter 8 8 Gasket Replacement Page 175

176 8.1 Gasket Replacement A gasket used for a long time may gradually lose its ability to protect the monitor from fluids and vapors; scratches or dirt may also accumulate. It is recommended that the gasket be replaced yearly. NOTE: If the monitor is mounted vertically, first remove it and place it on a flat, level surface with the display screen facing down before changing the gasket. Step 1: Remove the old gasket from the sides of the monitor. Step 2: Attach the new gasket to the monitor. Make sure the gasket fits precisely into the groove along the edges of the monitor s front panel (Figure 8-1). Figure 8-1: Gasket Replacement NOTE: Compliance with the IP 65 standard depends on correct installation of the gasket. Be sure to check that the gasket is properly installed after changing it. Page 176

177 Appendix A A Safety Precautions Page 177

178 WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the DM Series. A.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: A.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times. Follow the electrostatic precautions outlined below whenever the DM Series is opened. Make sure the power is turned off and the power cord is disconnected whenever the DM Series is being installed, moved or modified. Do not apply voltage levels that exceed the specified voltage range. Doing so may cause fire and/or an electrical shock. Electric shocks can occur if the DM Series chassis is opened when the DM Series is running. Do not drop or insert any objects into the ventilation openings of the DM Series. If considerable amounts of dust, water, or fluids enter the DM Series, turn off the power supply immediately, unplug the power cord, and contact the DM Series vendor. DO NOT: o Drop the DM Series against a hard surface. o Strike or exert excessive force onto the LCD panel. o Touch any of the LCD panels with a sharp object o In a site where the ambient temperature exceeds the rated temperature Page 178

179 A.1.2 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the DM Series may result in permanent damage to the DM Series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the DM Series. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the DM Series is opened and any of the electrical components are handled, the following anti-static precautions are strictly adhered to. Wear an anti-static wristband: Wearing a simple anti-static wristband can help to prevent ESD from damaging any electrical component. Self-grounding: Before handling any electrical component, touch any grounded conducting material. During the time the electrical component is handled, frequently touch any conducting materials that are connected to the ground. Use an anti-static pad: When configuring or working with an electrical component, place it on an antic-static pad. This reduces the possibility of ESD damage. Only handle the edges of the electrical component: When handling the electrical component, hold the electrical component by its edges. A.2 Maintenance and Cleaning Precautions When maintaining or cleaning the DM Series, please follow the guidelines below. A.2.1 Maintenance and Cleaning Prior to cleaning any part or component of the DM Series, please read the details below. Except for the LCD panel, never spray or squirt liquids directly onto any other components. To clean the LCD panel, gently wipe it with a piece of soft dry cloth or a slightly moistened cloth. Page 179

180 The interior of the DM Series does not require cleaning. Keep fluids away from the DM Series interior. Be cautious of all small removable components when vacuuming the DM Series. Turn the DM Series off before cleaning the DM Series. Never drop any objects or liquids through the openings of the DM Series. Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the DM Series. Avoid eating, drinking and smoking within vicinity of the DM Series. A.2.2 Cleaning Tools Some components in the DM Series may only be cleaned using a product specifically designed for the purpose. In such case, the product will be explicitly mentioned in the cleaning tips. Below is a list of items to use when cleaning the DM Series. Cloth Although paper towels or tissues can be used, a soft, clean piece of cloth is recommended when cleaning the DM Series. Water or rubbing alcohol A cloth moistened with water or rubbing alcohol can be used to clean the DM Series. Using solvents The use of solvents is not recommended when cleaning the DM Series as they may damage the plastic parts. Vacuum cleaner Using a vacuum specifically designed for computers is one of the best methods of cleaning the DM Series. Dust and dirt can restrict the airflow in the DM Series and cause its circuitry to corrode. Cotton swabs - Cotton swaps moistened with rubbing alcohol or water are excellent tools for wiping hard to reach areas. Foam swabs - Whenever possible, it is best to use lint free swabs such as foam swabs for cleaning. Page 180

181 Appendix B B Certifications Page 181

182 B.1 RoHS Compliant All models in the DM industrial monitor series comply with the Restriction of Hazardous Materials (RoHS) Directive. This means that all components used to build the industrial workstations and the workstation itself are RoHS compliant. The RoHS Directive bans the placing on the EU market of new electrical and electronic equipment containing more than agreed levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and polybrominated diphenyl ether (PBDE) flame retardants. B.2 IP 65 Compliant Front Panel The front panels on all five models in the DM series industrial monitor series have an ingress protection rating (IP) of 65, IP65. The front panels are protected from dust particles and water spray. Page 182

183 Appendix C C smartosd Page 183

184 C.1 IEI smartosd Quick Installation Guide IEI smartosd is a proprietary On-Screen-Display (OSD) software solution from IEI that enables easy, remote monitor setting adjustments in a Windows environment. IEI smartosd delivers excellent performance and provides more flexibility than the typical OSD hardware solutions when adjusting a monitor. smartosd also allows monitor settings such as brightness, contrast, screen position, size, color gain to be read and changed over normal video cable (VGA or DVI). The smartosd function is only supported by revision 1.1 models and above. C.2 Pre-installation Notice Before installing smartosd software, please make sure one of the following operating systems is installed: Windows 95 Windows NT 4.0 Windows 98 Windows 2000 Windows 2003 Windows XP Windows Vista C.3 Software Illustration The table below shows the smartosd menu structure for all IEI LCD monitors. NOTE: To update the display setting status immediately, push the refresh button on every page To turn the system on, press ALT + P. Page 184

185 Item Management EDID Image Display Color PIP System Elements Save/Load File Power Management EDID contains basic information about the monitor and its capabilities. Brightness Contrast Sharpness Auto Adjust Phase Clock Auto Color User Red Gain User Green Gain User Blue Gain Color Temperature (5000k and 4200k disabled in the DM Series) Gamma PIP (disabled in the DM Series) PIP Source Input (disabled in the DM Series) PIP Size (disabled in the DM Series) Monitor Power Control Auto Brightness (disabled in the DM Series) Main Source Input (S-Video and CVBS disabled) Volume (disabled in the DM Series) Factory Presets/OSD Lock/OSD Unlock Mute (disabled in the DM Series) Table C-1: SmartOSD Menu Structure Page 185

186 C.3.1 EDID Page Page 186

187 C.3.2 Image Page Page 187

188 C.3.3 Display Page (for analog signal) Page 188

189 C.3.4 Color Page Page 189

190 C.3.5 PIP Page NOTE: The functions in the PIP page are only available in the MDM Series and AFOLUX Series monitors. Page 190

191 C.3.6 System Page NOTE: Some of the functions in the System Page are only available to some of the IEI LCD series as following: Auto Brightness: SRM, MDM and AFOLUX series only Main Source Input: MDM and AFOLUX series only Volume: AFOLUX series only Mute: AFOLUX series only Page 191

192 C.3.7 User Page Page 192

193 C.3.8 About Page C.4 Install Software To install the software, please follow the steps below: Step 3: Follow the instructions from the interactive installer to install the IEI smartosd on the system. Step 4: Insert the installation disk that came with the system and open the installation file. Page 193

194 Step 5: The welcome screen shown below appears. Step 6: Click Next to continue. Step 7: The screen below appears. Page 194

195 Step 8: Select the installation folder from the screen shown above. Step 9: Click Next to continue. Step 10: The screen shown below appears. Page 195

196 Step 11: Confirm the installation by clicking Next in the screen above. Step 12: The program starts to install and the progress bar shown below appears. Page 196

197 Step 13: When the installation is complete the screen below appears. Step 14: Click Close in the screen above. Step 15: After quick setup is complete, the IEI smartosd wizard logo appears on the desktop as shown in the screen below. Step 16: To access the smartosd, click the smartosd wizard logo.step 0: Page 197

198 Page 198 DM Series Industrial Monitor

199 C.5 smartosd FAQ For troubleshooting, please see the steps below: C.5.1 Windows 2000 Installation Failure Installation fails under Windows 2000 and shows the following image: Figure C-1: DLL Missing Solution: Download and install service pack Windows Installer 3.1 Page 199

200 C.5.2 Vista Installation Failure Installation fail under Vista while showing following image: Figure C-2: Windows Vista Error Solution: Install SmartOSD.exe as the administrator authority Figure C-3: Install as Administrator Page 200

201 C.5.3 Model Failure The Model Fail error message shown below appears. Figure C-4: Firmware Incompatibility Solution: SmartOSD only supports firmware version 2.0 and following versions. C.5.4 DCC Port Failure The DDC port fail error message shown below appears. Figure C-5: DCC Port Failure Solutions: i. Check VGA or DVI cable ii. Check an IEI monitor is being used iii. Make sure the version is version 2.3 for the AFOLUX/MDM series and version 1.5 for the DM/ISDM/TDM/SRM/LCD-KIT series that have the SmartOSD functions iv. Check if the OSD control status is busy. A busy signal may cause the signal message for a short time. Page 201