PT-FX400 S P E C F I L E. LCD Projector. Downloaded from manuals search engine

Transcription

1 Product Number : Product Name : PT-FX4 As of March 2. Specifications and appearance are subject to change without notice. / 3 SFLM6-

2 PT-FX4 Specifications Main unit Power supply Power consumption LCD panel Panel size Display method Pixels Pixel configuration Lens Throw ratio Lamp Screen size Colors Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency Optical axis shift HDMI/DVI-I (digital) DVI-I (analog)/rgb YPBPR (YCBCR) Video/S-Video Keystone correction range Installation Built-in speaker Size Output power Terminals HDMI IN 24 V AC, A, 5/6 Hz 33 W (.3 W at 2 V AC,.4 W at 2224 V AC when standby mode set to eco,* 9 W when standby mode set to normal, 2 W when standby mode set to normal and audio monitor out.) 2.3 mm (.8 inches) diagonal (4:3 aspect ratio) Transparent LCD panel ( 3, R/G/B) 786,432 (,24 768) 3, total of 2,359,296 pixels Stripe Manual (2 zoom), manual focus F.72.6, f mm : 25 W UHM lamp m (333 inches) diagonally, 4:3 aspect ratio Full color (6,777,26 colors) 4, lumens 8% 6: (full on/full off), pixels (Input signals that exceed this resolution will be converted to, pixels.) fh: 27. khz 68.7 khz, fv: 24. Hz 85. Hz, dot clock: 25.2 MHz 48.5 MHz fh: 5.6 khz 9. khz, fv: 24. Hz 85. Hz, dot clock: 62 MHz or lower 48i (525i): fh 5.75 khz; fv 6 Hz, 576i (625i): fh 5.63 khz; fv 5 Hz, 48p (525p): fh 3.5 khz; fv 6 Hz, 576p (625p): fh 3.25 khz; fv 5 Hz, 72 (75)/6p: fh 45. khz; fv 6 Hz, 72 (75)/5p: fh 37.5 khz; fv 5 Hz, 8 (25)/6i: fh khz; fv 6 Hz, 8 (25)/5i: fh 28.3 khz; fv 5 Hz, 8 (25)/24p: fh 27. khz; fv 24 Hz, 8 (25)/6p: fh 67.5 khz; fv 6 Hz, 8 (25)/5p: fh khz; fv 5 Hz fh: 5.75 khz, fv: 6 Hz [NTSC/NTSC4.43/PAL-M/PAL6] fh: 5.63 khz, fv: 5 Hz [PAL/PAL-N/SECAM] Vertical: ±5% from center of screen (manual), horizontal: ±27% from center of screen (manual) Vertical: ±3 Ceiling/desk, front/rear (menu selection) 4 cm (-9/6 inches) (round) 5. W (monaural) HDMI 9-pin, Deep Color, HDCP compatible 48p (525p), 576p (625p), 72 (75)/6p, 72 (75)/5p, 8 (25)/6i, 8 (25)/5i, 8 (25)/24p, 8 (25)/6p, 8 (25)/5p VGA (64 48) WSXGA+ (,68,5), compatible with noninterlaced signals only, dot clock: 25.2 MHz46.25 MHz Audio signal: linear PCM (sampling frequencies: 48 khz, 44. khz, 32 khz) As of March 2 2/3 SFLM6-

3 Power cord length Cabinet materials Dimensions (W H D) Weight Operation noise Operating temperature Operating humidity Remote control unit Power supply Operation range* 6 Dimensions (W H D) Weight Supplied accessories DVI-I IN* 3 Digital R, G, B Y, PB (CB), PR (CR) (RGB) IN R, G, B Y, PB (CB), PR (CR) VIDEO IN S-VIDEO IN AUDIO IN AUDIO IN 2 AUDIO IN 3 AUDIO OUT SERIAL IN LAN WIRELESS MODULE PT-FX4 DVI-I 29-pin DVI. compliant, compatible with HDCP, compatible with single link only 48p (525p), 576p (625p), 72 (75)/6p, 72 (75)/5p, 8 (25)/6i, 8 (25)/5i, 8 (25)/24p, 8 (25)/6p, 8 (25)/5p VGA (64 48) WSXGA+ (,68,5), compatible with noninterlaced signals only, dot clock: 25.2 MHz46.25 MHz G:.7 Vp-p (. Vp-p for sync on G), 75 ohms; B, R:.7 Vp-p, 75 ohms; HD/VD, SY: high impedance, TTL (positive/negative) NOTE: SY/HD and VD terminals do not accept tri-level sync signals. Y:. Vp-p (including sync signal); PB (CB), PR (CR):.7 Vp-p, 75 ohms D-sub HD 5-pin (female) G:.7 Vp-p (. Vp-p for sync on G), 75 ohms; B, R:.7 Vp-p, 75 ohms; HD/VD, SY: high impedance, TTL (positive/negative) NOTE: SY/HD and VD terminals do not accept tri-level sync signals. Y:. Vp-p (including sync signal); PB (CB), PR (CR):.7 Vp-p, 75 ohms RCA pin,. Vp-p, 75 ohms Mini DIN 4-pin, Y:. Vp-p; C:.286 Vp-p, 75 ohms M3 (L, R ), input impedance: 22 kilohms or more M3 (L, R ),.5 Vrms, input impedance: 22 kilohms or more RCA 2 (L, R ),.5 Vrms, input impedance: 22 kilohms or more M3 (L, R ) (monitor out: 2. Vrms, variable) D-sub 9-pin, for external control (parallel) RJ-45, for network connection, Base-TX/Base-T, compliant with PJLink Connector for optional wireless module ET-WM2U/WM2E 2. m (6 ft 7 in) Molded plastic (PC + ABS) 43 mm 25.5 mm* mm (6-5/6 4-5/6* /32 inches) (including the lens) Approximately 6. kg (3.2 lbs) 33 db (lamp mode: NORMAL), 29 db (lamp mode: ECO) 4 C (32 4 F)* 5 2%8% (no condensation) 3 V DC (R6/LR6/AA type battery 2) Approximately 5 m (49 ft 3 in) when operated from directly in front of the signal receptor mm (-3/32 6-5/8 3/32 ) Approx. 7 g (4. oz) (including batteries) Power cord with security lock ( ) Wireless remote control unit ( ) Batteries for remote control (AA/R6/LR6 type 2) Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring and Control Software Ver. 2.5, Wireless Manager ME 5.5) ( ) As of March 2 3/3 SFLM6-

4 Wireless Manager ME 5.5 system requirements Optional accessories Replacement lamp unit Replacement filter unit Ceiling mount bracket Wireless module OS Web browser CPU Memory Free hard disk space CD-ROM drive Wireless LAN Wired LAN connector PT-FX4 To use network functions, a PC is required that meets the conditions given below. Microsoft Windows XP: Professional 32-bit, Home Edition 32-bit, Tablet PC Edition bit Windows Vista : Ultimate 32-bit/64-bit, Business 32-bit/64-bit, Home Premium 32-bit/64-bit, Home Basic 32-bit/64-bit Windows 7: Ultimate 32-bit/64-bit, Professional 32-bit/64-bit, Home Premium 32-bit/64-bit Apple Mac OS X* 7 : v.4, v.5, v.6 Windows : Internet Explorer 6./7./8. Mac OS: Safari 2./3./4. Windows : GHz or higher Intel Pentium III or higher, or other compatible processor Mac OS X: GHz or higher PowerPC G4, or.8 GHz or higher Intel Core processor 256 MB or more (52 MB or higher is recommended for Mac OS X) 6 MB or more CD-ROM drive or DVD drive (required for installation) The optional ET-WM2 is required. IEEE 82.b/g/n compatible (built-in wireless LAN system or external IEEE 82.b/g/n LAN card must be installed and running normally.) NOTE: Wireless connection may not be possible with some IEEE 82.b/g/n wireless LAN systems. Macintosh computers must have a built-in wireless LAN adapter. For IEEE 82.n connection, use a wireless LAN adapter, projector and access point that are IEEE 82.n compatible, and connect with Infrastructure mode. RJ-45 ET-LAFA ET-EMF ET-PKFH (for high ceilings) ET-PKFS (for low ceilings) ET-WM2U (for rth America) ET-WM2E (for Europe and Asia) Weights and dimensions shown are approximate. Specifications subject to change without notice. * When the standby mode is set to ECO, network functions such as power on over the LAN network will not operate. Also, only certain commands can be received for external control using the serial terminal. *2 Measurement, measuring conditions, and method of notation all comply with ISO 28 international standards. *3 The DVI-I IN terminal also accepts analog signals. *4 With legs at shortest position. *5 Operation range differs depending on environments. *6 The operating temperature range is C35 C (32 F95 F) when used in High-Altitude mode (,4 m (4,593 ft) to 2,7 m (8,858 ft)). *7 The operation system must be pre-installed at the factory or clean installed. As of March 2 4/3 SFLM6-

5 PT-FX4 Dimensions unit : mm (inch) NOTE: This illustration is not drawn to scale. 323 (2-23/32) 53 (2-3/32) 43 (6-5/6) 7 (2-25/32) 25.5 (4-5/6).5 5 (3/32) (4-7/32) (9) Terminals LAN LAN connector 2 HDMI input DVI-I IN IN S-VIDEO IN 3 DVI-I input IN VIDEO IN 4 Computer input VARIABLE AUDIO IN AUDIO IN 3 AUDIO OUT R L 5 S-Video input AC IN MAIN 6 Video input POWER OFF ON 7 Serial input 8 Audio input Audio input 2 Audio input 3 Audio out put SERIAL IN As of March 2 5/3 SFLM6-

6 PT-FX4 Standard setting-up position ** Adjustable in 2 mm (25/32 ) steps. H Upper edge of projected image Projected image L 49 (-5/6) 42 (-/6) 94 (7-5/8) (4-7/32 7-/6) Adjustable in 2-mm (5/32-inch) step. L H Lower edge of projected image NOTE: 7 (2-3/4) 65 (2-9/6) Illustrations show the projector installed using optional ceiling mount bracket ET-PKFH. This illustration is not drawn to scale. L Projected image 3 (/2) unit : mm (inch) Projection distance for 4:3 aspect ratio screen Projection size [diagonal] Projection distance [L] Min [wide] Max [telephoto] unit: meters (feet) Height from the edge of screen to center of lens [H].84 m / 33 ().9 (6.4).5 (.7).2 m / 4.2 (3.8) 2.4 (7.8).6 ( 2.).27 m / 5.5 (4.8) 3. (9.7).76 ( 2.5).52 m / 6.8 (5.8) 3.6 (.7).9 ( 3.).78 m / 7 2. (6.8) 4.2 (3.7).7 ( 3.5) 2.3 m / (7.8) 4.8 (5.7).22 ( 4.) 2.29 m / (8.9) 5.4 (7.7).37 ( 4.5) 2.54 m / 3. (9.9) 6. (9.7).52 ( 5.) 3.5 m / (.9) 7.2 (23.6).83 ( 6.) 3.8 m / (4.9) 9. (29.6) 2.29 ( 7.5) 5.8 m / 2 6. (9.9) 2. (39.5) 3.5 (.) 6.35 m / (24.9) 5. (49.4) 3.8 ( 2.5) 7.62 m / 3 9. (29.9) 8. (59.3) 4.57 ( 5.) NOTE: The value for H (the height from the edge of the screen to the centre of the lens) is the value when the horizontal optical axis shift function is not used. The value decreases when the horizontal optical axis shift function is used. For details, see Shift range on page 7. The value for L (distance to screen) varies slightly depending on the zoom lens characteristics. At the shortest projection distance, the zoom lens characteristics may cause slight image distortion. When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size. The brightness varies depending on the zoom setting. As of March 2 6/3 SFLM6-

7 PT-FX4 Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 4:3 minimum L (m) = (diagonal screen size in inches) maximum L (m) = (diagonal screen size in inches).64.5 NOTE: Distances calculated with the above equations will include a slight error. Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image).27h.27h V (Height of projected image).5v.5v Standard postition of projected image Installable angle Install the projector at an angle within the range shown below. Vertical direction The projector may be installed at a vertical angle of 3. Horizontal direction The projector may not be angled horizontally As of March 2 7/3 SFLM6-

8 PT-FX4 List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 5.6 khz to 9. khz, vertical scanning frequencies of 24. Hz to 85. Hz, and a dot clock of 62 MHz maximum can be input. NOTE: The native resolution of this projector is, pixels. If the display resolution of the input signal is different from the native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution. Display mode NTSC/NTSC4.43/ PAL-M/PAL6 PAL/PAL-N/SECAM 48i (525i) 576i (625i) 48p (525p) 576p (625p) 72 (75)/6p 72 (75)/5p 8 (25)/6i 8 (25)/5i 8 (25)/24p 8 (25)/6p 8 (25)/5p 92 8 VESA VGA SVGA MAC XGA WIDE75 (72) WXGA768 WXGA8 MXGA MAC MSXGA SXGA SXGA6+ WXGA+ UXGA WSXGA+ WUXGA Display resolution (dots)* 72 48i i 72 48i i ,28 72,28 72,92,8i,92, ,24 768,28 72,28 768,28 8,52 864,52 87,28 96,28,24,4,5,44 9,6,2,68,5,92,2 Scanning frequency H V (khz) (khz) Dot clock frequency (MHz) * The i appearing after the resolution indicates an interlaced signal. Format VIDEO/S-VIDEO /YPBPR HDMI/DVI//YPBPR HDMI/DVI/ HDMI/DVI/ HDMI/DVI/ HDMI/DVI/ HDMI/DVI/ HDMI/DVI/ HDMI/DVI/ Plug and Play compatibility HDMI DVI-D input Computer/ input EDID EDID2 DVI-I (analog) As of March 2 8/3 SFLM6-

9 PT-FX4 Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names D-sub 9-pin (female) Serial input Signal name TXD RXD GND Description Send data Receive data Ground Signal name RTS CTS Description Connected internally Connected internally Connected internally Communication conditions (factory setting) Signal level Synchronization method Baud rate Parity Character length Stop bit X parameter S parameter RS-232C-compliant Start-stop synchronization 9,6 bps ne 8 bits bit ne ne Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. STX A D I I2 ; C C2 C3 : P P2... Pn ETX Start (2 bytes) ( byte) Semicolon ( byte) ID 2 characters (2 bytes) Colon End ( byte) ( byte) Command Parameters (3 bytes) (undefined length) (Control and/or query commands) ID designator: to 6: Projector ID number ZZ: All units (ID ALL) CAUTION It may not be possible to send or receive commands for about to 6 seconds when the lamp is first turned on. If this occurs, wait for 6 seconds, then try sending or receiving again. When sending multiple commands, be sure to wait for at least.5 second after receiving a response from the projector before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to seconds or more. When using two or more units, set different IDs for each unit. As of March 2 9/3 SFLM6-

10 PT-FX4 Cable specifications Projector PC (DTE) Control commands Command: <Parameter> Function Callback: <Parameter> Parameter value Min Max PON* POF* AVL: IIS:<input signal> OST OFZ:<off on> OEN OXG: OXG: OXG: 2 VPM:<NAT> VPM:<STD> VPM:<CIN> VPM:<DYN> VPM:<BBD> VPM:<WBD> VXX:DLVI=<+> VXX:DLVI=<+> VXX:DLVI=<+2> AUU AUD OMN OCU OCD OCL OCR OAS OSH* / * 2 OIX DZU DZD TSD:<date> TST:<time> Power on (standby mode on) Power off (standby mode off) Volume control Input signal selection The same function as default button Freeze Enter Wide mode: Off Wide mode: On Wide mode: Auto Picture mode: Natural Picture mode: Standard Picture mode: Cinema Picture mode: Dynamic Picture mode: Blackboard Picture mode: Whiteboard Daylight View: Off Daylight View: Auto Daylight View: On Volume up Volume down Menu Cursor up Cursor down Cursor left Cursor right Auto setup AV mute Index window Digital zoom: Enlargement Digital zoom: Reduction Date setting Time setting PON* POF* AVL: IIS:<input signal> OST OFZ:<off on> OEN OXG: OXG: OXG: 2 VPM:<NAT> VPM:<STD> VPM:<CIN> VPM:<DYN> VPM:<BBD> VPM:<WBD> VXX:DLVI=<+> VXX:DLVI=<+> VXX:DLVI=<+2> AUU AUD OMN OCU OCD OCL OCR OAS OSH* / * 2 OIX DZU DZD TSD:<date> TST:<time> * Do not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. *2 When a command that cannot be executed during standby mode is sent, the projector will send an ER4 command in reply. 63 As of March 2 /3 SFLM6-

11 PT-FX4 Status request commands Command Description Callback <Parameter> QPW Q$S QIN QAV QVC QVT QVB QVR QVS QHP QVP QCP QDC QSP QLG QXG QVX:DLVI QPM QFZ Q$L QSH QKS QTE QGD QGT Standby power status Lamp status Input signal status Volume adjustment value Color adjustment value Tint adjustent value Brightness adjustment value Contrast adjustment value Sharpness adjustment value Horizontal position adjustment value Vertical position adjustment value Clock phase adjustment value Dot clock adjustment value Projection method status On-screen menu language Wide mode status Daylight View status Off On Auto Picture mode status Off Auto On Natural Standard Cinema Freeze status Dynamic Lamp run time Blackboard AV mute function statuswhiteboard Keystone correction status Color temperature adjustment status Date setting status Time setting status NOTE: If a wrong command is received, the projector will send an ER4 command to the computer. <power condition> <lamp condition> <input signal> <> <> <2> <+> <+> <+2> <NAT> <STD> <CIN> <DYN> <BBD> <WBD> <off_on> <acctch> <off_on> <color temp> <date> <time> As of March 2 /3 SFLM6-

12 PT-FX4 Parameter format Parameter format Size (Byte) Definition 3 ( or 2 bytes also possible when under control) <off on> <input signal> 3 <power condition> <lamp condition> <acctch> <color temp> <date> <time> Decimal without signs: 999 (,, ) Decimal with signs: -99 to +99 ( , +, +, ) Callback from the projector is 3 Byte. = off, = on HD = HDMI, DVI = DVI-I, RG = computer, NWP = network, VID = video, SVD = S-Video = power off (standby mode off), = power on (standby mode on) = standby, = lamp on under control, 2 = lamp off, 3 = lamp off under control Dicimal without signs: hours = low, = default, 2 = high yy2y3y4mm2dd2w = year (y) month (m) day (d) day of week (w) Day of week: Monday =, Tuesday = 2,... Sunday = 7 hh2mm2ss2 = hour (h) minute (m) second (s) NOTE: If a wrong command is received, the projector will send an ER4 command to the computer. Command example To set the volume to +3, send the command as shown below. STX AVL : 3 ETX Start Command Parameter End NOTE: When sending commands without parameters, a colon (:) is not necessary. As of March 2 2/3 SFLM6-

13 PT-FX4 tes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions.. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 5 mm (9-/6 ) or more around the projector s exhaust openings. In addition to this space, also ensure that there is a sufficient work space for removing and installing the lamp, filter and other parts. 3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection. When stacking projector units, be sure to provide the amount of space indicated below between them. These space requirements also apply to installations where only one projector unit is operating at one time and the other unit is used as a backup. 3. If the projector is installed in an enclosed space, ensure that the projector s intake and exhaust openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings. 2 mm (7-7/8 ) or more 5 mm (9-/6 ) or more 5 mm (9-/6 ) or more mm (3-5/6 ) or more Do not stack projector units directly on top of one another. Direction of air intake and exhaust Intake Exhaust Operating the projector continuously. If the projector is to be operated continuously hours or more, lamp replacement cycle duration becomes shorter. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods (one hour or less). Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. Product availability differs depending on region and country. This product may be subject to export control regulations. PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions. Intel, Pentium, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the United States and/or other countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a trademark of International Business Machines Corporation, registered in the U.S. All other trademarks are the property of their respective trademark owners. As of March 2 3/3 SFLM6-