Editing Controller Setting

Transcription

1 EC0-00 Editing Controller etting : AJ-D0P/D0E/D50P/D50E/D50P/D50E hen the AJ-D0P/D0E/D50P/D50E/D50P/D50E is connected with the Editing Controller, the settings of VTR side and Controller side are set as follows; Applicable to : BVE-00 BVE-900 BVE-90 BVE-9000 RM-50 ACE-5 (Ver. 3.c) AG-A0 AU-A950 BVE-800 BVE-900K BVE-000 FXE-00 PVE-500 AG-A350 AG-A800 AU-A90 * Note * In case of connecting the AG-A850, the controller is initial setting and the ETUP Menu No. 0 : "ID EL" on the VTR side is set to "DVCPRO". Applicable model in the tables are as follows; 55 mode : AJ-D0P/D50P/D50P 5 mode : AJ-D0E/D50E/D50E AJ-D0 has no editing function. Please use the AJ-D0 only as a Player.

2 ETUP Menu setting data of VTR side is default (factory) setting except comments. PREROLL TIME of Controller is set to 5 sec. BVE-00 etting BVE-800 etting BLOCK- BLOCK- BYTE BYTE mode A A 0C 0 FB D FF 5 mode 5 00 B A 0C 0 FB B FF BLOCK- BYTE-5 (Edit Delay) : 08 = - frame BYTE- (EE Delay) : 08 = - frame BYTE-8 (Trajectory) : high byte 8 = Cue Up by CUE UP ITH., and 3 on the 9 Pin Interface Board of Recorder side are set as follows; 3 R/P etting Edit Timing Play Timing Recorder - Frame - 5 Frame /5 mode ON OFF OFF ON OFF ON ON OFF ON OFF ON ON., and 3 on the 9 Pin Interface Board of Player side are set as follows; (Blank frame in the chart is not changed) 3 R/P etting Edit Timing Play Timing Recorder - Frame - 0 Frame /5 mode OFF ON OFF ON OFF ON ON ON OFF ON OFF ON (Blank frame in the chart is not changed) - (Time Code Discontinuity Process) : ON = CTL is not compensated 3- (ynchronization Accuracy) : ON = ± 0 frame For cueing up smoothly, ETUP Menu No. 0 FF.RE MAX of the VTR is set to X3 or X0. In case of I/F software version is more than N.0, set the ETUP Menu No. 33 AFTER CUE UP to TOP (0000). At BVE-800, editing is executed when the VTR goes to TOP mode after CUE-UP completion. BVE-900 (Ver.0) etting CONTANT CONTANT mode A 0F 0C 0 FB D 0 5 mode 5 00 D A 0F 0C 0 FB B 0 CONTANT- -5 (Edit Delay) : 08 = - frame - (EE Delay) : 08 = - frame - (Overrun) : Compensation for tape overrunning time from the appointed Preroll point during Preroll top period. -8 (Trajectory) : Regulate the optimum trajectory curve during Preroll mode CONTANT- - (Preroll peed) : 0 = HUTTLE X3 Page / EC0-00

3 BVE-900 Ver.0, Ver.09, Ver.0 and Ver. are set as same as BVE-900K. (CUE-UP can be available by CUE UP ITH ) hen CONTANT- - and -8 and CONTANT- - are set to the above condition, CUE-UP is smoothly functioned but CUE-UP speed is late. BVE-900 Ver.0 cannot be cueing-up by CUE UP ITH. BVE-900K, BVE-90 etting CONTANT CONTANT mode A 0C 0 FB D FF 5 mode 5 00 D A 0C 0 FB B FF CONTANT- -5 (Edit Delay) : 08 = - frame - (EE Delay) : 08 = - frame -8 (Trajectory) : high byte 8 = Cue Up by CUE UP ITH BVE-000 etting mode A 0C 0 FB D FF 5 mode 5 00 D A 0C 0 FB B FF -5 (Edit Delay) : 08 = - frame - (EE Delay) : 08 = - frame -8 (Trajectory) : high byte 8 = Cue Up by CUE UP ITH BVE-9000 etting CONTANT CONTANT mode A 0C 0 FB D FF 5A 5 mode 5 00 D A 0C 0 FB FF B FXE-00 etting CONTANT- -5 (Edit Delay) : 08 = - frame - (EE Delay) : 08 = - frame. Player VTR device constant (ETUP Menu No. 0 and 0) is set to DIABLE. (As the user setting code is not available, built-in constant is available). Recorder VTR device constant (ETUP Menu No. 03) is set to ENABLE and as follows; /5 mode FF FF 00 5A A 08 FB E FF ( in the chart is different from factory setting) BYTE-05 (Edit Delay) : 08 = - frame BYTE-0 (EE Delay) : 08 = - frame BYTE-3 (MODE ) : CF ON NTC 8 = F LOCK PAL 83 = 8F LOCK Page 3/ EC0-00

4 BYTE- (MODE ) : while CF status from the VTR is effective F while CF status from the VTR is not effective E VTR Device Code BVE-00 / BVE-900 / BVE-900K / BVE-9000 / BVE-000 / FXE-00 BLOCK BYTE ITEM CONTENT Device Type et the VTR type. 3 Min Preroll Time et the minimum Preroll Time which is required by the VTR. 5 Edit Delay Compensate the delay time from which the REC command is transmitted to the VTR and then the recording is started. (Frame unit) EE Delay Compensate the delay time from which the PB/EE control command is transmitted to the VTR and then the VTR goes to the Preview mode. (Frame unit) Overrun Compensate the extra running time when the tape is passed over the Preroll point during Preroll top period. (Frame unit) 8 Trajectory Const Regulate the optimum trajectory curve during Preroll period. (Poor convergence VTR has a big value) High byte 8 = Cue Up by CUE UP ITH * BVE-900 (Ver..0) cannot be available with the Cue Up by CUE UP ITH. BLOCK BYTE ITEM CONTENT TC Read Delay Compensate the delay time from which the tape is run and then the time code reading is actually stared. (Frame unit) tart Delay Compensate the delay time from which the run command is transmitted to the VTR and then the VTR is turned ON actually. (Frame unit) 3 After-ync Delay - et the optimum command delay time, which is servo-locked to the right position from the lower speed direction, when the mode is changed to PLAY after synchronization is completed. (Frame unit) After-ync Delay + et the optimum command delay time, which is servo-locked to the right position from the higher speed direction, when the mode is changed to PLAY after synchronization is completed. (Frame unit) 5 Max Framing CTL Interpolation CF tatus Enable Max Frame Lock Time BIT : et the maximum framing which shows the VTR format. 0 = F LOCK = F LOCK = 8F LOCK Despite of YNCHRONIZE setting on the ystem etting Panel, the corresponding VTR is controlled by the framing which is less than the assigned framing. BIT8 : = CTL compensation of time code can be available. 0 = Not available. BIT : = CF status from the VTR is available. 0 = Not available BIT 8 : et the maximum time up to frame-lock of VTR. (Frame unit) Preroll peed et the maximum speed of HUTTLE mode when the Preroll (CUE UP) is executed. FF = Control by the FF/RE mode 9P INTERFACE Board (BK-809) etting : PLAYER//RECORDER etting witch Purpose of VTR Use RECORDER ON PLAYER ON PLAYER (Blank frame in the chart is OFF) Page / EC0-00

5 - : Edit Command Timing witch Output Timing of Edit Command (Frame) - * ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON 3 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON * Default etting (Blank frame in the chart is OFF) - : election of CUE UP (In case of PROM (IC9 0) software on MP- Board is more than Version 3) ON = CUE UP by the EARCH mode OFF = CUE UP by FF/RE (over sec) + EARCH (within sec) - : Time code discontinuity process (In case of PROM (IC9 0) software on MP- Board is more than Version ) ON = Discontinuity process is not performed. OFF = Discontinuity process is performed. (CTL is used at the Preroll and synchronization from the IN point) -8 :No use of 9P INTERFACE Board (BK-80) 3- : PLAY Command Timing witch Output Timing of PLAY Command (Frame) * ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON 3 ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON * Default etting (Blank frame in the chart is OFF) etting Method of PLAY Command Output Timing. Insert the tape ( min) which is recorded the video signal continuously to each VTR.. et the EDIT NUMBER to 900. (Press the key 9 first and then 0 and 0 pressing the EDIT# key simultaneously.) 3. Press the PREVIE key. Run the VTR with the PREVIE mode and then stop automatically. hen the PREVIE lamp is turned OFF, the data is displayed on the time counter at the same time. * Note * hen the VTR is Recorder side, it performs with selecting the EDIT PREET.. et the 3- as this data is frame number described above table. 3- : ynchronization Accuracy ON = ± 0 frame OFF = ± frame 3- : No use of 9P INTERFACE Board (BK-80) 3-8 : Color Framing witch ON = CF edit is executed on the YNCHRONIZE OFF position. OFF = CF edit is not executed on the YNCHRONIZE OFF position. AU-A950 (before Ver for NTC) etting CONTANT CONTANT mode 0 5 FF FF F FF Page 5/ EC0-00

6 CONTANT- -5 (Edit Delay) : 0 = - frame - (EE Delay) : 0 = - frame CONTANT- -3 (After ync Delay) : 9F = 0 frame hen cueing up smoothly, ETUP Menu No. 0 FF.RE MAX of the VTR is set to X3. AU-A950 (after Ver.0-05 for NTC) etting CONTANT CONTANT mode 0 5 FF FF FF FF CONTANT- -5 (Edit Delay) : 0 = - frame - (EE Delay) : 0 = - frame CONTANT- - (MODE) : 00 = ynchronize after ervo Lock 0 = ynchronize after Play OUTPUT hen cueing up smoothly, ETUP Menu No. 0 FF.RE MAX of the VTR is set to X3. AU-A950 (Ver.0-05 for PAL) etting CONTANT CONTANT mode 5 FF FF C 0 FF FF CONTANT- -5 (Edit Delay) : 0 = - frame - (EE Delay) : 0 = - frame CONTANT- - (MODE) : 00 = ynchronize after ervo Lock 0 = ynchronize after Play OUTPUT For cueing up smoothly, ETUP Menu No. 0 FF.RE MAX of the VTR is set to X3. CUE elect etting of Edit mode on AU-A950 (before Ver.0-0, NTC/PAL), AU-A90 (before Ver.-5, NTC/PAL) etting method by the ETUP Menu on the VTR side (etting of Controller side is not changed). However, only CUE cannot be selectable in this method.. et the ETUP Menu No. 30: EDIT RPLCEC on the VTR of Recorder side as follows. CH : elect the CUE at the same time of CH selecting. CH : elect the CUE at the same time of CH selecting. CH+ : elect the CUE at the same time of CH or CH selecting. Changing method of Controller side setting. et the ETUP Menu No. 0 : ID EL on the VTR of Recorder side to DVCPRO (000).. Recorder VTR device constant is set as follows; AU-A950 (before Ver for NTC) etting CONTANT CONTANT mode F0 33 FF FF F FF Page / EC0-00

7 AU-A950 (after Ver.0-05 for NTC) etting CONTANT CONTANT mode F0 33 FF FF FF FF AU-A950 (Ver.0-05 for PAL) etting CONTANT CONTANT mode F 33 FF FF C 0 FF FF 3. AUDIO CHANNEL AIGN of Controller is set as follows. ANALOG A (CUE) = CUE KEY * DIGITAL A = A KEY ANALOG A (CUE) = CUE KEY * DIGITAL A = A KEY ANALOG A3 (TC) = TC KEY DIGITAL A3 = A3 KEY ANALOG A = A KEY DIGITAL A = A KEY * etting of selecting the CUE edit mode by CUE key is displayed. AU-A950 (after Ver.0-0, NTC/PAL), AU-A90 (after Ver.-, NTC/PAL) etting. et the ETUP Menu No. 0 : ID EL on the VTR of Recorder side to DVCPRO (000).. Recorder VTR device constant is set as follows; CONTANT CONTANT /5 mode FF FF FF FF FF FF 3. AUDIO CHANNEL AIGN of Controller is set as follows. ANALOG A (CUE) = CUE KEY * DIGITAL A = A KEY ANALOG A (CUE) = CUE KEY * DIGITAL A = A KEY ANALOG A3 (TC) = TC KEY DIGITAL A3 = A3 KEY ANALOG A = A KEY DIGITAL A = A KEY * etting of selecting the CUE edit mode by CUE key is displayed. AG-A0 etting. and on the Panel side are set as follows; mode ON ON 5 mode ON ON (Blank frame in the chart is set to OFF). (50) and (50) on the I/F Unit side are set as follows; (50) (50) mode ON ON 5 mode ON ON ON (Blank frame in the chart is set to OFF) -5 - : 9P Edit Timing -5 ON - OFF = - frame - ON 3. et the ETUP Menu No. 0 : PLAY DELAY to 5 on the Recorder side of the VTR. * Note * hen set to above setting, normal playback is also late. et the ETUP Menu No. 0 : PLAY DELAY to 0 on the Player side of the VTR. Page / EC0-00

8 AG-A0 (Ver.) Dip etting Panel side Buzzer ound ON No sound OFF ound No use 3 No use ynchronization ON Perform by the CAP OVERRIDE. Operation elect OFF Perform by the earch mode. 5 Preroll Time ON 3 sec OFF 5 sec Postroll Time ON sec OFF sec ynchronization In case of setting this to ON, the setting of -8 is not available. ON No synchronization OFF Perform synchronization 8 Editing Grade ON Retry times. If it fails, the editing is stopped. OFF No retry. If it fails, the editing is continued. No use D3 huttle Mode ON It is switched to the VAR mode during HTL X - X + OFF It is not switched. Edit Timing Auto This setting is only available with - OFF setting. 3 election ON In case of VTR ID is "000", the edit timing is followed with the 50-5, and setting on the I/F Unit side. OFF In case of VTR ID is "000", the edit timing is set to - frame. Edit Timing Auto ON Edit timing is followed with the 50-5, and setting on the I/F Unit side. election OFF The VTR ID automatically sets edit timing. 5 TC Read Mode ON Only LTC. OFF VITC or LTC. DF/NDF etting ON DF OFF NDF Color Framing Editing ON Perform the Color Framing Editing. (However VTR ETTING) election OFF Not perform the Color Framing Editing. 8 Multi Event ON/OFF ON ingle event is fixed. OFF Multi Event can be available to switch from the single event by the EVENT key. I/F Unit side (50) (50) NTC/PAL witching 3P IN point - Frame 3 No use No use 5 Edit Timing 8 No use No use No use 3 No use No use 5 No use No use No use 8 No use ON PAL OFF NTC hen the picture is confirmed using the VIDEO OUT terminal on the 3P Interface Board, frame shift between the actual TC and displayed TC is compensated. In case of using the MARK-IN/OUT key or GOTO key, this setting is effective. ON Compensation is performed. OFF Compensation is not performed. Frame OFF OFF OFF OFF ON ON ON ON - OFF OFF ON ON OFF OFF ON ON - OFF ON OFF ON OFF ON OFF ON Page 8/ EC0-00

9 AG-A350 etting. Dip witch of AG-A350 is set as follows; mode OFF OFF ON OFF ON OFF ON 5 mode OFF OFF ON OFF ON OFF OFF. et the ETUP Menu No. 0 : PLAY DELAY to 5 on the Recorder side of the VTR. * Note * hen set to above setting, normal playback is also late. et the ETUP Menu No. 0 : PLAY DELAY to 0 on the Player side of the VTR. AG-A350 Dip etting (Blank frame in the chart is not changed) OFF ON etting CTL DIPLAY (CTL Counter Display) ± H H ON PLAYER EDIT REFERENCE (Counter mode on Player side) TC CTL ON 3 RECORDER EDIT REFERENCE (Counter mode on Recorder side) TC CTL ON YCRO VTR (ynchronization Control) PLAYER RECORDER OFF 5 CAP OVERRIDE -5, - (ynchronization, election of Color OFF OFF NOT YNCHRO (No ynchronization) ON Framing) ON OFF FRAMING (Framing, ynchronization) OFF ON COLOR FRAMING (Color Framing, ynchronization) ON ON VTR YNCHRO (etting on VTR side, ynchronization) OFF PREROLL TIME -, - (PREROLL Time etting) OFF OFF 0 sec ON ON OFF sec OFF ON 5 sec OFF ON ON 3 sec EDIT TIMING -3, - 3 (Edit Timing etting) OFF OFF - 8 frames OFF ON OFF - frames OFF ON - frames OFF ON ON -5 frames 5 AUDIO CH (Audio etting in Edit mode) AUDIO TC OFF IGNAL TANDARD (Frame) 5F (PAL) 30F (NTC) ON AG-A800 etting. and on the Panel side are set as follows; mode ON OFF OFF OFF OFF ON ON ON ON OFF ON OFF ON. (50) and (50) on the I/F Unit side are set as follows; Page 9/ (Blank frame in the chart is not changed) (50) (50) mode OFF ON ON OFF ON 5 mode ON ON ON OFF ON (Blank frame in the chart is not changed) 3. et the ETUP Menu No. 0 : PLAY DELAY to 5 on the Recorder side of the VTR. * Note * hen set to above setting, normal playback is also late. et the ETUP Menu No. 0 : PLAY DELAY to 0 on the Player side of the VTR. EC0-00

10 AG-A800 Dip etting Panel side Buzzer ound at ON* ound mis-operation OFF No sound Direct earch ON* Direct search can be available. OFF Direct search cannot be available. 3 No use et to ON. Recorder side ON* Perform by the CAP OVERRIDE. ynchronization OFF Perform by the earch mode. 5 Player side ON* Perform by the CAP OVERRIDE. ynchronization OFF Perform by the earch mode. Player side ON* Perform by the CAP OVERRIDE. ynchronization OFF Perform by the earch mode. No use et to OFF. 8 Editing Grade ON* Retry times. If it fails, the editing is stopped. OFF No retry. If it fails, the editing is continued. Control Panel ON* ON OFF OFF GPI3 witching ON* Audio Edit Point Timing OFF KEY Output Point Edit Timing Auto This setting is only available with - OFF mode 3 election ON In case of VTR ID is "000", the edit timing is followed with the 50-5, and setting on the VTR side. OFF* In case of VTR ID is "000", the edit timing is set to - frame. Edit Timing Auto ON Edit timing is followed with the 50-5, and setting on the I/Funit side. election OFF* The VTR ID automatically sets edit timing. 5 No use et to OFF. No use et to ON. Postroll Time ec 0.5 * 3 - OFF OFF ON ON 8-8 OFF ON OFF ON I/F Unit side (50) (50) No use et to OFF. VTR Action ON* ON OFF OFF 3 witcher election - AG-800* KM3000 GVG00-3 OFF OFF ON ON - OFF ON OFF ON 5 Edit Timing Frame OFF OFF OFF OFF ON ON ON ON - OFF OFF ON ON OFF OFF ON ON - OFF ON OFF ON OFF ON OFF ON 8 PC Communication ON Communication is finished unless receiving the data within about 3 sec. Time Out OFF* No time out. R3 Contents Communication ON bit Data Length OFF* 8 bit TOP Bit ON* OFF 3 PARITY ON ON OFF* OFF ODD/EVEN ON EVEN OFF* ODD 5 File End Process ON* CR, LF, ^Z Output 8 BAUD RATE OFF ^Z Output * ON ON ON ON OFF OFF OFF OFF - ON ON OFF OFF ON ON OFF OFF -8 ON OFF ON OFF ON OFF ON OFF Page 0/ EC0-00

11 ACE-5 (Ver. 3.c) etting. Press the keys, [Y INIT] [HARDARE CONFIG] [ONY PROTOCOL], and then set the protocol to CVR-5.. Press the keys, [Y INIT] [YTEM OPTION] then the menu is EDIT OPTION. et the ENTRY OFFET in the EDIT OPTION to -3 Frames. 3. etting on the VTR side ). ETUP-MENU 0 : FF.RE MAX = X3 ). ETUP-MENU 0 : ID EL = OTHER 3). ETUP-MENU 300 : VAR RANGE = - + < Complement > JOG operation of ACE-5 is not too good. It is caused by too much speed data change of the command. PVE-500 etting. et the ETUP- : ED DELAY (Edit Delay) on the PVE-500 side to F ( frames). ). Press the ETUP (ENTRY + EDIT) button. ). Rotate the earch Dial on the Player side and then display "ETUP-". 3). Rotate the earch Dial on the Recorder side and then set to "F". ). Press the TORE (ENTRY + REC) button. 5). Press the ETUP (ENTRY + EDIT) again and then close the ETUP mode.. et the ETUP Menu No. 0:PLAY DELAY to on the Recorder side of the VTR. * Note * hen set to above setting, normal playback is also late. et the ETUP Menu No. 0:PLAY DELAY to 0 on the Player side of the VTR. RM-50 etting. YTEM REET on the RM-50 side is set as follows; Left side Number etting OFF OFF ON OFF OFF OFF OFF OFF Right side Number etting OFF OFF OFF ON OFF ON ON OFF. et the ETUP Menu No. 0 : PLAY DELAY to on the Recorder side of the VTR. * Note * hen set to above setting, normal playback is also late. et the ETUP Menu No. 0 : PLAY DELAY to 0 on the Player side of the VTR. 3. After selecting the Edit mode, insert the recorded tape in both Player and Recorder sides and push the LEARN button. Page / EC0-00