WE-EF LEUCHTEN Technical information for Eco Step Dim Basic Product ID 430-0001
Eco Step Dim Basic General information All WE-EF Eco Step Dim components are intended for professional users. Installation and start-up may only be performed by persons with the relevant technical knowledge. Please read these instructions carefully before installing and starting up the system. It is the only way to ensure safe and proper operations. Please keep these instructions on file, so they are available for later use if required. WE-EF is not liable for the incorrect connection and the improper use of its products. The reliable functioning of Eco Step Dim products requires that they have been programmed and started up accordingly. Safety information All works on the equipment may only be carried out after power to the equipment has been disconnected. The applicable safety and accident prevention provisions must be adhered to. The improper opening of the products is not permitted; there is danger to life due to electrical voltage. Repairs may only be performed by the manufacturer. The electronic ballast loses its zero-potential once the controller is connected to the control input. Eco Step Dim Basic Schema Electronic Controller integral (included in delivery) Switchboard Hand Held Programmer Adaptor Software Download www.we-ef.com Phase line Optional for On-site-Programming Hand Held Programmer incl. Adaptor and Software: 405-0122 WE-EF Eco Step Dim Basic requires an external switch phase. The switch phase may come from any source. A pre-programmed capacity level is turned on and off in the luminaire by connecting or disconnecting the control phase. When the control phase is turned off, the luminaire changes to dimming mode. The electronic controller can be updated without limitations, and the firmware can be adapted or re-imported as necessary. This requires a hand-held programming device and application software, which are not included in the delivery scope. Please contact your WE-EF representative or the technical WE-EF Hotline at +49 5194 909209 (Monday to Friday from 8:00 am to 4:00 pm). 1
Eco Step Dim Basic Electronic Controller The electronic controller is already built into the luminaire by WE-EF, and is delivered ready-made in accordance with customer requirements (see Form Sheet in the Appendix). The dimming level can also be adjusted at a later time. The configuration of the connection line can be found in the illustrations below. The electronic controller is suited for installation in IP66 luminaires. Technical data Input voltage:....................... 230VAC +/-10% AC Line frequency...................... 50 Hz (+1 % / -2 %) Power consumption................... <0.5W PF=0,1 Galvanic separation................... No potential separation input to output As soon as the electronic ballast is connected to the electronic controller, the control input is no longer galvanically separated. Switching current.................... 4A, λ = 0.8 Switch cycles........................ 50000, Function (I, λ) Programmable....................... Yes Can be parametrised.................. Yes Control output 1-10V................. Short-circuit proof Control output DALI................... Short-circuit proof, 2mA configured for a slave Connection clamps................... 0.5 to 1.5mm² Conductor type of connection clamp..... Single-wire, fine-wire Firmware Update / Parametrisation...... Via universal input without current with electronic controller Climatic conditions Operating temperature range Tc......... 25 C to +80 C Storage temperature range............. 25 C to +85 C Humidity........................... 90% non-condensing Standards Impulse withstand voltage............. 4kV / 1.2 / 50 according to DIN EN 61037 Protection class..................... SKI (SKII on request) Degree of protection.................. IP20 Enclosure Material........................... Plastic enclosure made of polycarbonate Dimensions......................... (W/H/D) 81 mm / 20 mm / 41 mm Weight............................. 32 g 2
Eco Step Dim Basic Connection diagram Eco Step Dim Basic Standard programming* 80% 60% D2 50% 40% 20% 0% ON** OFF** * For customised programming at the factory, please complete form on page 4 and submit to WE-EF with purchase order ** ON / OFF defined by user, using a dimmer switch (photocell) *** Cycle times for the phase is defined by the user 3
Eco Step Dim Basic Programming For customised programming at the factory, please enter the required dimming level in the "Customised Programming" table. WE-EF Standard Programming* WE-EF Standard Programming 80% Step Ramp Niveau 60% D2 50% 12 min. 100 % 40% D2 3 min. 50 % 20% 0% ON** OFF** * For customised programming at the factory, please complete form and submit to WE-EF with purchase order ** ON / OFF defined by user, using a dimmer switch *** Cycle times for the phase is defined by the user Individual Programming Step Ramp Niveau % D2 % will be completed by WE-EF Order number Lamp description Work steps Name Date File Name Program completed Program transferred Programm checked 4
Eco Step Dim Basic Accessories The accessories listed below can be used to make modifications (on-site programming). Hand-held programmer incl. Adaptor and Software.........WE-EF item number 405-0122 If you would like to speak with one of our experts, please contact us by e-mail: info.germany@we-ef.com 5
www.we-ef.com WE-EF LEUCHTEN Germany Tel +49 5194 909 0 Fax +49 5194 909 299 info.germany@we-ef.com Thailand Tel +66 2 738 9610 Fax +66 2 175 2174 info.asiapacific@we-ef.com WE-EF LUMIERE France Tel +33 4 74 99 14 44 Fax +33 4 74 99 14 40 info.france@we-ef.com Australia Tel +61 3 8587 0444 Fax +61 3 8587 0499 info.australia@we-ef.com WE-EF HELVETICA Switzerland Tel +41 22 752 49 94 Fax +41 22 752 49 74 info.switzerland@we-ef.com United States of America Tel +1 724 742 0030 Fax +1 724 742 0035 info.usa@we-ef.com United Kingdom Tel +44 844 880 5346 Fax +44 844 880 5347 info.uk@we-ef.com Eco Step Dim Basic_010416 / 006-1125 Technische Änderungen vorbehalten. Technical specifications are subject to change. WE-EF 2016