CTV BULLETIN. When replacing IC201, identify chip type as described and order using the part numbers in the table below. N1 VERSION N3 VERSION
|
|
- Eugene Briggs
- 5 years ago
- Views:
Transcription
1 TB124 Issue No: 01 CI5944/6844 CI5344(SCT 12A/B) Application: erence (* ) Only ed Sets ( ) Whole Sets () Subject: CHANGE OF IC201 (ONE CHIP) TYPE New Parts Supply When replacing IC201, identify chip type as described and order using the part numbers in the table below. TDA 8375 BATHCODE DATECODE 1X MASK NUMBER TDA 8375 BATHCODE DATECODE MASK NUMBER 3Y N1 VERSION N3 VERSION DEVICE TYPE VERSION PART NUMBER CHASSIS TDA8375 N SCT12B TD8375 N SCT12B TDA8374A N SCT12A TDA8374 N (French only) SCT12A TDA8374A N SCT12A Changeover from N1! N3 occurred August 1997 Serial Number 3JCH8xxxxx
2 TB126 Issue No: 01 CI3373T SCT11D (00 TO 01) Application: erence ( ) Only ed Sets ( X) Whole Sets () Subject: BUZZ/WHISTLE ON SOUND Intermittent buzz/whistle on sound Inter modulation distortion traced to Micom Crystal which oscillates at 12 MHz, a harmonic of which is beating with the SIF via a ground loop. Remove C907 and fit a 104 (50v) ceramic capacitor as shown In the diagram C907 DPR Y I IRIS Information
3 Document TB127 : Issue No: 01 CI5344 Product Group: Application: erence ( ) Only ed Sets ( ) Whole Sets ( ) Subject: FAILURE OF FRAME IC (IC301) Frame Collapse Tube Flash Over Replace frame IC301. Solder Zener Diode onto the underside of PCB as shown. Part number V Zener Diode. C 301 R 302 V2 V1 NON-CONDUCTIVE TAPE EY EY26 DFL Z I IRIS Information For Warranty Claims
4 TB139 Issue No: 01 CI5079/ SCT11B/D Page: 1 Application: erence ( ) Only ed Sets ( X) Whole Sets () Subject: HIGH B+ IN STANDBY MODE 125V rail at approx 180V in standby (should be 140V) Due to a mismatch in the resonubber circuit. C852 should be changed to a polyester type V Part No: C852 PSU Y I IRIS Information
5 TB141 Issue No: 01 CI5933/6230/ 7230/ Pages: 2 Application: erence ( ) Only ed Sets ( X) Whole Sets () Subject: FAILURE OF FRAME OUTPUT CHIP, IC301 (TDA 3654) Partial or complete frame collapsetb141 Noise on V1 Line of TDA Remove previous mods 2. Fit 2 parts as illustrated. IRIS Information
6 V1 V2 V1 C305 PJ 28 C305 R316 V1 R316 R305 REPLACE PJ28 ->10uh R305 BEFORE C306 R303 IC401 R321 ADD 470nF CAP FIT CLOSE TO IC PIN #5 AFTER C306 R303 IC401 R317 C302 C303 #5 #1 #3 IC301 TDA3654 C302 #5 #1 #3 IC301 TDA3654 NO 1 2 CCT REF ADD POLY PJ28 SPEC BEFORE AFTER REMARKS CODE NO SPEC 100V 470nF 10UH AL05 CODE NO
7 TB142 Issue No: 01 CI5944/6844 SCT12 B CHASSIS Pages: 1 Application: erence ( ) Only ed Sets ( X) Whole Sets () Subject: FAILURE OF F801 MAINS INPUT FUSE Dead set (no standby LED) F801 o/c Replace F801 with 4A anti surge New part number: Replace F801 on all units for repair regardless of fault F801 PSU R A IRIS Information
8 V1 V2 V1 C305 PJ 28 C305 R316 V1 R316 R305 REPLACE PJ28 ->10uh R305 BEFORE C306 R303 IC401 R321 ADD 470nF CAP FIT CLOSE TO IC PIN #5 AFTER C306 R303 IC401 R317 C302 C303 #5 #1 #3 IC301 TDA3654 C302 #5 #1 #3 IC301 TDA3654 NO 1 2 CCT REF ADD POLY PJ28 SPEC BEFORE AFTER REMARKS CODE NO SPEC 100V 470nF 10UH AL05 CODE NO
9 TB147 Issue No: CHASSIS S15A CI14F1T CI3373 CI /03/99 Page: ONE Application: erence ( ) Only ed Sets (X) Whole Sets ( ) Subject: DISTORTED SIBILANCE Distorted sibilance on certain programs C614 out of tolerance Replace C 614 with new type part no C614 APA Y I
10 TB148 Issue No: CHASSIS SCT 13B CI 3373 CI 5373 CI /03/99 Page: ONE Application: erence ( ) Only ed Sets (X) Whole Sets ( ) Subject: WHISTLE ON SOUND Whistle on sound. Varies with volume. Inter modulation distortion traced to micom crystal. Fit insulated wire link as shown. (From link J190 to C911-ve). ONE CHIP IC201 MICOM IC C911 DPR Y I J190 + C911 -
11 TB152 Issue No: 01 CI-3373 CI-5079 CI-5373 CI-5073 SCT11B, PIB,SCT11D CHASSIS Page: 1 OF 1 Application: erence ( ) Only ed Sets ( ) Whole Sets () Subject: POWER SUPPLY FAILURE/INT. FAILURE OF Q401 Dead. DZ801 Short /Q401 Short. Replace the following PSU parts. Check/replace Q401 as necessary. DZ IC801 AA P HC801 AA M F L803 AA G C C C (Q The chassis number is printed underneath the FBT on solder side of PCB DZ801 PSU Q A IC801 - Q A HC801 - Q A IRIS Information for Warranty Claims F801 - R A L803 - R A C803 - Q A C851 - Q A C852 - Q A
12 TB153 Issue No: 01 CI-14F1Z/T CI-20S10BZ CI-20S20BT CI-21S20BT CI-5079Z/T CI-5373Z/T CI-3373Z/T S15A, SCT13B CHASSIS Page: 1 OF 1 Application: erence ( ) Only ed Sets ( ) Whole Sets () Subject: FAILURE OF IC801 (KA3S0680RF) Dead Set. C804 incorrectly inserted. De-solder and re-fit C804 Replace IC801 Part No IC801 PSU A A C804 PSU T D
13 Document : TB155 Issue No: 01 Chassis S15A, SCT13B, S51A 11/11/99 Application: erence ( ) Only ed Sets (!) Whole Sets ( ) Subject: FAILURE OF IC801 (PSU) No Power Surge Flow into VCC Terminal Fit a 30v, 0.5w Zener from Pin 3 (IC801) to ground. Part Number The chassis number is printed under the F.B.T. (on solder side) IC801 PSU Q A IRIS Information For Warranty Claims
14 TB82 Issue No: 03 Bulletin Type: Information CI3373, CI5373, CI5079 C T V APPLICATION: erence ( ) Only ed Sets ( ) Whole Sets ( ) Subject: Power Supply Failure SCT11B Chassis This Bulletin has been re-released due to changes in the versions of available components. Dead DZ801 Short Replace the following parts. erence Part Number - Version DZ IC801 HC801 AA P - Ver C AA M - Ver C F D2801 PSU Q A IC801 PSU Q A HC801 PSU Q A IRIS Information F801 PSU R A
15 TB83 Issue No: 01 Bulletin Type: Information CI5344AN SCT 12A Chassis CI6844 / 5944 SCT 12B Chassis C.T.V Subject: New Crystal Types Used In Production X201, X202 The new Crystals are not directly compatible with the old type. The old Crystals are marked KDSI or PHILIPS The new Crystals are marked KONY When replacing KDSI or PHILIPS Crystal to KONY, the Parallel Resonance Capacitor must be changed to match the Crystal type. X201 and C218 go together as a pair and similarly X202 and C219 are a pair. erence Part Number Description X MHz 30 ppm X202 A MHz 30 ppm C Ceramic 56 Pf, 5%, 50 V C Ceramic, 100 Pf, 2%, 50 V X201 CPA A A X292 CPA A A C218 CPA A A IRIS Information C219 CPA A A
16 TB83 Issue No: 01 Bulletin Type: Information CI5344AN SCT 12A Chassis CI6844 / 5944 SCT 12B Chassis C.T.V Subject: New Crystal Types Used In Production X201, X202 The new Crystals are not directly compatible with the old type. The old Crystals are marked KDSI or PHILIPS The new Crystals are marked KONY When replacing KDSI or PHILIPS Crystal to KONY, the Parallel Resonance Capacitor must be changed to match the Crystal type. X201 and C218 go together as a pair and similarly X202 and C219 are a pair. erence Part Number Description X MHz 30 ppm X202 A MHz 30 ppm C Ceramic 56 Pf, 5%, 50 V C Ceramic, 100 Pf, 2%, 50 V X201 CPA A A X292 CPA A A C218 CPA A A IRIS Information C219 CPA A A
17 TB86 Issue No: 01 CI-5373T, CII-5079T Application: erence ( ) Only ed Sets ( ) Whole Sets () Subject: INTER MODULATION DISTORTION Buzz / Whistle on sound. Inter Modulation Distortion traced to Micom Crystal which Oscillates at 12 MHz, a Harmonic of which is beating with the SIF via a Ground Loop. Locate C907. Remove the Capacitor and fit in position C907A. DISTRIBUTION: Clive Bingham Ian Merrington Mike Stevenson Malcolm Jones Zdena Best Colin Brewer Judy Stevenson David Castle C907 DPR Y K IRIS Information
18 TB90 Issue No: 01 CI5079Z/T Page: 2 Application: erence ( ) Only ed Sets ( ) Whole Sets () Subject: CRT ESD PROBLEM Cyclic start up from cold (can be intermittant). Frame collapse. (Due to faulty frame IC). Electrostatic discharge through the frame IC causing Micom to reset. Fit an insulated wire link between EY23 and EL07 (See diagram). This modification is for the SCT 11B chassis version 04/05 only. See diagram for identification. 2 11B EL07 DFL U 1 IRIS Information
19 TB95 Issue No: 01 CI5373T Application: erence ( ) Only ed Sets ( ) Whole Sets () Subject: CHANGE OF MICOM TYPE New parts supply. Original Type - SAA 5290ZP-026 (Part No: AA A) New Type - SAA 5290ZP-042 (Part No: AA T) When fitting new type Micom the following adjustment should be carried out in Factory Mode to change the option BYTE. Switch set on and key in the following sequence using the remote. STBY, P.STD, HELP, SLEEP, STBY Select option BYTE from the Factory Menu and change from "5D" to "CA". Note: The IRIS information will depend upon the fault found. IRIS Information
20 TB110 Issue No: 1 TVP5050 TVP5350 TVCR Application: erence (* ) Only ed Sets ( ) Whole Sets () Subject: CHASSIS CHANGE FROM SCV11A TO SCV11D The circuit and some major parts have been changed Chassis change from SCV11A to SCV11D. The chassis version is marked underneath F.B.T. on print side The changes are listed below. Location No. Old (before) Parts (SCV11A) New (changed) Parts (SV11D) SEC Description SEC Description IC Tuner (1) Tuner (2) FBT IC-MCU IC-Video AA M AA B AA E AA L TECC2989PA19C TECC2889PA19C FTK20R008C CXP85332A-196S TDA6101Q AA N AA M AA Y AA Y TECC2979PK28A(S) TECC2879PK28A(S) FSV20A001 CXP85332A-319S TDA6107Q D D D D D IRIS Information
21 TB111 Issue No: 1 TVP3350 TVCR Application: erence (* ) Only ed Sets ( ) Whole Sets () Subject: CHASSIS CHANGE FROM SCV11B TO SCV11D The circuit and some major parts have been changed Chassis change from SCV11B & C to SCV11D. The chassis version is marked underneath F.B.T. on print side The changes are listed below. Location No. Old (before) Parts (SCV11B & C) New (changed) Parts (SV11D) SEC Description SEC Description IC Tuner (1) Tuner (2) IC-MCU IC-Video AA M AA B AA L TECC2989PA19C TECC2889PA19C CXP85332A-196S TDA6101Q AA N AA M AA Y TECC2979PK28A(S) TECC2879PK28A(S) CXP85332A-319S TDA6107Q D D D D IRIS Information
Specifications. FTS-260 Series
Specifications DVB-S2 NIM Tuner Date : 2014. 03. 26. Revision F2 #1501, Halla sigma Valley, 442-2 Sangdaewon-dong, Jungwon-gu, Sungnam City, Gyeonggi-do, Korea, 462-807 Tel. 86-755-26508927 Fax. 86-755-26505315-1
More informationNixie Clock Type Quattro'
Assembly Instructions And User Guide Nixie Clock Type Quattro' - 1 - Issue Number Date REVISION HISTORY 2 8 Sept 2012 Errors corrected 1 27 July 2012 New document Reason for Issue - 2 - 1.1 Nixie Quattro
More informationGUIDE TO ASSEMBLY OF ERICA SYNTHS DELAY MODULE
If you are reading this, most probably, you are about to build Erica Synths DIY DELAY module. The module is 4mm deep, skiff friendly, has solid mechanical construction and doesn t require wiring. Erica
More informationADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT
ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT BUILD INSTRUCTIONS Before you start take a look at the Printed Circuit Board (PCB). The components go in the side with the writing on
More informationTEKTRONIX 2465B OSCILLOSCOPE: MAIN BOARD INTER-TRACK LEAKAGE.
TEKTRONIX 2465B OSCILLOSCOPE: MAIN BOARD INTER-TRACK LEAKAGE. Dr. H. Holden. June 2014. This article describes a complex fault which developed in one of my three Tektronix 2465B oscilloscopes. I decided
More informationMONO AMPLIFIER KIT ESSENTIAL INFORMATION. Version 2.2 CREATE YOUR OWN SPEAKER DOCK WITH THIS
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS MONO AMPLIFIER KIT Version 2.2 Build Instructions
More informationSpecifications. FTS-4335 Series
Specifications DVB-S2 DUAL NIM Date : 2017. 03. 17. Revision F2 #1501, Halla sigma Valley, 442-2 Sangdaewon-dong, Jungwon-gu, Sungnam City, Gyeonggi-do, Korea, 462-807 Tel. 0755-26504227 Fax. 0755-26505315
More informationARCAM ALPHA 5 CD PLAYER SERVICE MANUAL
ARCAM ALPHA 5 CD PLAYER SERVICE MANUAL 1 ALPHA 5 CD SERVICE MANUAL ALPHA 5 CD PLAYER SERVICE MANUAL Issue 1 Serial No. 30000 Paul Newton/Andy Howe August '93 Arcam Drawing No. H04/0022 CONTENTS CIRCUIT
More informationWS2815 Intelligent control LED integrated light source
Features and Benefits The control circuit and RGB chip are integrated in a 5050 components, to form an external control pixel. 12V DC power supply, can effectively reduce the operating current of the pixel
More informationFR205, 142 CPS1804. Power Supply Control .33Ω, 2W, K, nF. CPT uF 4148, 130 A64 3A-T , 116
9 A B C D E F G H I J 17V for PS IC Remote Connector 100K, 113 392K, 529 0Ω, 132 30Ω,139 4937, 141 62K, 143A 002 POWER 510Ω, 004 1371 149 200pF, 138 0Ω, 533 FR205, 142 CPS1804 1 003 112 115A 18Ω, 133 Wire
More informationPHILIPS Anubis A(AC) Chassis
PHILIPS Anubis A(AC) Chassis Recommended Safety Parts Item Part No. Description 4822 276 12597 MAIN SWITCH 4822 258 30274 FUSE HOLDER 4822 255 40955 LED HOLDER 4822 267 60243 EURO CONN. 4822 265 30389
More informationNewScope-7A Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7A Operating Manual Preliminary May 13, 2017 NewScope-7A Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 3 3
More informationVideo Streamer Modifications
CB Electronics Video Streamer Modifications CB Electronics Loddonside, Lands End House, Beggars Hill Road, Charvil, Berks RG10 0UD, UK Tel: +44 (0)118 9320345, Fax: +44 (0)118 9320346 URL: www.colinbroad.com
More informationMONITOR POWER Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2099-10xx 10MHz Frequency Source April 2014, Rev. H MENU INTERNAL LEVEL = +10dBm MONITOR POWER 1 2 MODEL 2099 FREQUENCY SOURCE CROSS TECHNOLOGIES INC. ALARM OVEN REMOTE EXECUTE
More informationN3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB
N3ZI Digital Dial Manual For kit with Backlit LCD Rev 4.00 Jan 2013 PCB Kit Components Item Qty Designator Part Color/Marking PCB 1 LCD Display 1 LCD 1602 Volt Regulator 1 U1 78L05, Black TO-92 Prescaler
More informationESU LokSound Select Direct Micro "Keep-Alive"
ESU LokSound 73100-73199 Select Direct Micro "Keep-Alive" Last Updated 180520 There has been a lot of discussion on the internet about adding "Keep-Alive" capacitors to sound decoders to improve performance
More informationSDA 3302 Family. GHz PLL with I 2 C Bus and Four Chip Addresses
GHz PLL with I 2 C Bus and Four Chip Addresses Preliminary Data Features 1-chip system for MPU control (I 2 C bus) 4 programmable chip addresses Short pull-in time for quick channel switch-over and optimized
More informationN3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012
N3ZI Digital Dial Manual For kit with Serial LCD Rev 3.04 Aug 2012 Kit properly assembled and configured for Standard Serial LCD (LCD Not yet connected) Kit Components Item Qty Designator Part Color/Marking
More informationAssembly Instructions And User Guide. Nixie FunKlock. FunKlock Issue 4 (1 February 2017)
Assembly Instructions And User Guide Nixie FunKlock - 1 - Issue Number Date REVISION HISTORY 4 1 February 2017 New diode for D2 3 27 December 2013 C7 / C8 error page 15 2 7 November 2013 Errors corrected
More informationIntegrated Circuit for Musical Instrument Tuners
Document History Release Date Purpose 8 March 2006 Initial prototype 27 April 2006 Add information on clip indication, MIDI enable, 20MHz operation, crystal oscillator and anti-alias filter. 8 May 2006
More informationV6118 EM MICROELECTRONIC - MARIN SA. 2, 4 and 8 Mutiplex LCD Driver
EM MICROELECTRONIC - MARIN SA 2, 4 and 8 Mutiplex LCD Driver Description The is a universal low multiplex LCD driver. The version 2 drives two ways multiplex (two blackplanes) LCD, the version 4, four
More informationLX600 LCD TV Technical Information
LX600 LCD TV Technical Information TC-32LX600 Outline Features Overall Block Diagram A Board Main Layout Power On Sequence Protection Shutdown Troubleshooting Adjustments 1 Features Model TC-LX60 TC-LX600
More information1. Unlocking your FT847 to get 4m ( for those who already have unlocked one, please move to chapter 2).
Modification Yaesu FT-847 dla pasma 70MHz Part II practical solution v. 1.0 (Oct 2013) Greg SP3RNZ sp3rnz@wp.pl PA mod idea by Marc PA1O TX/RX mod idea by Hellar ES1II/8 This article describing how to
More informationEM1. Transmissive Optical Encoder Module Page 1 of 8. Description. Features
Description Page 1 of 8 The EM1 is a transmissive optical encoder module designed to be an improved replacement for the HEDS-9000 series encoder module. This module is designed to detect rotary or linear
More informationMODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec.
MODIFYING A SMALL 12V OPEN FRAME INDUSTRIAL VIDEO MONITOR TO BECOME A 525/625 & 405 LINE MULTI - STANDARD MAINS POWERED UNIT. H. Holden. (Dec. 2017) INTRODUCTION: Small open frame video monitors were made
More informationRECORD & PLAYBACK KIT
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE ADD AN AUDIO MESSAGE TO YOUR PRODUCT WITH THIS RECORD & PLAYBACK KIT Version 2.1 Index of Sheets TEACHING
More informationREV CHANGE DESCRIPTION NAME DATE. A Release
REV CHANGE DESCRIPTION NAME DATE A Release 10-13-09 Any assistance, services, comments, information, or suggestions provided by SMSC (including without limitation any comments to the effect that the Company
More informationDSO138mini Troubleshooting Guide
DSO138mini Troubleshooting Guide Applicable main board: 109-13800-00I Applicable analog board: 109-13801-00H 1. Frequently Found Problems 1) LCD completely dark. No backlight 2) LCD lights up but no display
More informationBuild Your Own Clone Relay Bypass Board Instructions
Build Your Own Clone Relay Bypass Board Instructions Parts list for the Relay Bypass Board Resistors: 1-2k2/222 (Red/Red/Black/Brown/Brown) 1-10k/103 (Brown/Black/Black/Red/Brown) Capacitors: 2-100n/.1uF/104
More informationWORLDSEMI CO., LIMITED WS2813. Intelligent control integrated LED light source. Dual-signal wires version Signal break-point continuous transmission
WORLDSEMI CO., LIMITED WS2813 Intelligent control integrated LED light source Dual-signal wires version Signal break-point continuous transmission April-2016 1 / 11 Features and Benefits The control circuit
More informationBGA2022, RX mixer 880, 1950 and 2450 MHz
Philips Semiconductors BGA2022, RX mixer 880, 1950 and 2450 MHz Application Note AN00059 APPLICATION NOTE BGA2022, RX mixer 880, 1950 and 2450 MHz AN00059 Author(s): Hans ten Cate Philips Semiconductors
More information1. Power Light: Check the master switch (ON/OFF) and the fuse to see if they are operating. < Blinking Temp & Timer LED > Yes. Yes Replace fan(s)
6. Troubleshooting 6-1 Checkpoints by Error Mode 1. Power Light: Check the master switch (ON/OFF) and the fuse to see if they are operating. 2. LED Blinking: See the basic LED checklist in 6-2-1. < Blinking
More informationTECHNOLOGY WILL SAVE US: THE LUMIPHONE
TECHNOLOGY WILL SAVE US: THE LUMIPHONE This is a step-by-step guide to soldering your own Lumiphone. The equipment you should have at your station: goggles, soldering mat, soldering Iron, solder and side
More informationSPECIFICATION. DVB-T/ DVB-C / Worldwide hybrid Switchable NIM Tuner
1.Feature *. Integrated RF switch, NTSC VIF demodulator, COFDM demodulator *. All-in-one full NIM function with compact size, optimal solution for cost reduction and shortening product development lead-time.
More informationNixie Clock Type Frank 2 Z570M
Assembly Instructions And User Guide Nixie Clock Type Frank 2 Z570M Software version: 7R PCB Revision: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 2 is a compact design with
More informationXTAL Bank DDS Version 0.02 Sept Preliminary, highly likely to contain numerous errors
XTAL Bank DDS Version 002 Sept 7 2012 Preliminary, highly likely to contain numerous errors The photo above shows the fully assembled Xtal Bank DDS with 2 DDS modules installed (The kit is normally only
More informationReaction Game Kit MitchElectronics 2019
Reaction Game Kit MitchElectronics 2019 www.mitchelectronics.co.uk CONTENTS Schematic 3 How It Works 4 Materials 6 Construction 8 Important Information 9 Page 2 SCHEMATIC Page 3 SCHEMATIC EXPLANATION The
More informationCP-830FP Chassis TX-29E50D TX-29E50D/B TX-29PS12D TX-29PS12F TX-29PS12P SPECIFICATIONS. Order No: PCZ C2
Order No: PCZ0510103C2 SPECIFICATIONS Power Source: Power Consumption: 220-240V a.c.,50hz 100W Stand-by Power Consumption: 1,5W Aerial Impedance: 75Ω unbalanced, Coaxial Type Receiving System: PAL-I, B/G,
More informationSERVICE AND OPERATION MANUAL
MTG-2907TN Publication A. Issue 1 SERVICE AND OPERATION MANUAL MTG- 2907TN OPEN FRAME VGA COLOR MONITORS MTG-2907TN : 29INCH, FST Information in this publication current as of Jun, 2003. Information subject
More informationIndustriefunkuhren. Technical Manual. IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C / AFNOR NF S87-500
Industriefunkuhren Technical Manual IRIG-B Generator-Module for analogue / digital Signals of Type: IRIG-B / IEEE C37.118 / AFNOR NF S87-500 Module 7628 ENGLISH Version: 02.01-06.03.2013 2 / 20 7628 IRIG-B
More informationOBSOLETE. CMOS 80 MHz Monolithic (18) Color Palette RAM-DACs ADV478/ADV471
a FEATURES Personal System/2* Compatible 80 MHz Pipelined Operation Triple 8-Bit (6-Bit) D/A Converters 256 24(18) Color Palette RAM 15 24(18) Overlay Registers RS-343A/RS-170 Compatible Outputs Sync on
More informationASM-2 Manual Appendix A
ASM-2 Manual Appendix A Assembly Guidelines June 30 th, 2005 Please note that this document is still currently under revision and we apologise for any errors or omissions. Readers should feel free to e-mail
More information8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT BOARD)
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS LEARN ABOUT PROGRAMMING WITH THIS 8 PIN PIC PROGRAMMABLE BOARD (DEVELOPMENT BOARD & PROJECT
More informationLF101XF Six Function DCC Function Only Decoder Art. No February 2007
LF101XF function decoder 1 The DIGITAL plus by Lenz LF101XF function decoder is suitable for use in all scales. Features include: Six function outputs rated at 200mA each with advanced function mapping.
More informationIntroduction 1. Green status LED, controlled by output signal ST. Sounder, controlled by output signal Q6. Push switch on input D6
Introduction 1 Welcome to the GENIE microcontroller system! The activity kit allows you to experiment with a wide variety of inputs and outputs... so why not try reading sensors, controlling lights or
More informationSynchronization circuit with synchronized vertical divider system for 60 Hz TDA2579C
FEATURES Synchronization and horizontal part Horizontal sync separator and noise inverter Horizontal oscillator Horizontal output stage Horizontal phase detector (sync to oscillator) Triple current source
More informationDIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX
DIY Guide - Building Franky v1.1, the SEGA Audio and Videocard for MSX 2015 FRS & MSXpró. Translation by FRS and Supersoniqs. Table of Contents Introduction... 3 Materials needed... 3 Audio volume boost...
More informationLM MHz RGB Video Amplifier System with OSD
LM1279 110 MHz RGB Video Amplifier System with OSD General Description The LM1279 is a full featured and low cost video amplifier with OSD (On Screen Display). 8V operation for low power and increased
More informationDIY KIT MHZ 8-DIGIT FREQUENCY METER
This kit is a stand-alone frequency meter capable of measuring repetitive signals up to a frequency of 50MHz. It has two frequency ranges (15 and 50 MHz) as well as two sampling rates (0.1 and 1 second).
More informationANTUMBRA FADE MANUAL
ANTUMBRA FADE MANUAL TABLE OF CONTENTS 01. INSTALLATION 4 02. BACK 5 03. FRONT 6 04. USE 7 05. LINK 8 06. BILL OF MATERIALS 9 07. BUILD NOTES 10 08. BACK 11 09. FRONT 14 10. MODIFICATION 15 11. FINISHED
More informationEM1. Transmissive Optical Encoder Module Page 1 of 9. Description. Features
Description Page 1 of 9 The EM1 is a transmissive optical encoder module designed to be an improved replacement for the HEDS-9000 series encoder module. This module is designed to detect rotary or linear
More informationIRT Eurocard. Type RWA RF Distribution Amplifier for 70 MHz IF signals
I R T Electronics Pty Ltd A.B.N. 5 000 8 575 6 Hotham Parade, ARTARMON N.S.W. 064 AUSTRALIA National: Phone: (0) 949 744 Fax: (0) 949 749 International: +6 949 744 +6 949 749 Email: sales@irtelectronics.com
More informationPixie Construction Notes
Pixie Construction Notes PCB V2a February 4 th 2015 Please note that this document is still currently under revision and we apologise for any errors or omissions. Readers should feel free to e-mail any
More informationOPERATOR MANUAL OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM
PTY. LTD A.B.N. 83 003 020 504 OPERATOR MANUAL OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM OSD390 SERIES 4 CHANNEL VIDEO/AUDIO/DATA FIBER OPTIC TRANSMISSION SYSTEM Document
More informationGEKCO SUBCARRIER REFERENCE OSCILLATOR MODEL SRO10 OPERATION/SERVICE MANUAL
GEKCO MODEL SRO10 SUBCARRIER REFERENCE OSCILLATOR OPERATION/SERVICE MANUAL GEKCO Labs PO Box 642 Issaquah, WA 98027 (425) 392-0638 P/N 595-431 REV 5/98 Copyright c 1998 GEKCO Labs All Rights Reserved Printed
More informationWP36BHD T-1 (3mm) Blinking LED Lamp
T-1 (3mm) Blinking LED Lamp DESCRIPTIONS The Bright Red source color devices are made with Gallium Phosphide Red Light Emitting Diode Electrostatic discharge and power surge could damage the LEDs It is
More information10MHz Source/Inserter
Instruction Manual Model 2099-218 10MHz Source/Inserter Redundant 18V January 2011, Rev. A RX 0.32 A TX 0.86 A REF ON REF OFF MENU MODEL 2099 SOURCE/INSERTER CROSS TECHNOLOGIES INC. PS1 PS2 REMOTE ALARM
More information10 GHz to 26 GHz, GaAs, MMIC, Double Balanced Mixer HMC260ALC3B
Data Sheet FEATURES Passive; no dc bias required Conversion loss 8 db typical for 1 GHz to 18 GHz 9 db typical for 18 GHz to 26 GHz LO to RF isolation: 4 db Input IP3: 19 dbm typical for 18 GHz to 26 GHz
More informationInstallation and User Guide 458/CTR8 8-Channel Ballast Controller Module
Installation and User Guide 458/CTR8 8-Channel Ballast Controller Module Helvar Data is subject to change without notice. www.helvar.com i Contents Section Page Introduction 1 Installation 2 1. Attach
More informationModuMAX SSPA Systems. C, X, and Ku Bands. Completely modular solid-state power amplifier systems for world-wide satellite communications
ModuMAX SSPA Systems C, X, and Ku Bands Completely modular solid-state power amplifier systems for world-wide satellite communications C-Band SSPAs 1500 Watts 1000 Watts 800 Watts X-Band SSPAs 1250 Watts
More informationNixie Clock Type Frank 3
Assembly Instructions And User Guide Nixie Clock Type Frank 3 Software version: 7R PCB Version: 11 April 09-1 - 1. INTRODUCTION 1.1 About the clock Nixie clock type Frank 3 is a compact design with all
More informationModel 6010 Four Channel 20-Bit Audio ADC Data Pack
Model 6010 Four Channel 20-Bit Audio ADC Data Pack Revision 3.1 SW v1.0.0 This data pack provides detailed installation, configuration and operation information for the Model 6010 Four Channel 20-bit Audio
More informationModel /29S RF Splitter
Instruction Manual Model 1584-29/29S RF Splitter March 2013, Rev. 0 LNB VOLTAGE A B MODEL 1584 COMBINER CROSS TECHNOLOGIES INC. GND+DC ON Data, drawings, and other material contained herein are proprietary
More informationBasic Level Crossing CCTV Notes. Page one of five
Page one of five Relays (PIC) SR (PIC) R (CC) SR (MON OFF) R (MON) R (CAM) PR (DAY) R (NIGHT) R (CAM OFF) R Normally energised, cameras on standby, pressing picture button deenergisers it and picture is
More informationDocumentation VFD clock 8 a clock
Documentation VFD clock 8 a clock This documentation is protected by our copyright. It must not be used for commercial purposes. Congratulations on your purchase of your VFD clock. To guarantee success
More informationDDS VFO CONSTRUCTION MANUAL. DDS VFO Construction Manual Issue 1.1 Page 1
DDS VFO CONSTRUCTION MANUAL DDS VFO Construction Manual Issue 1.1 Page 1 Important Please read before starting assembly STATIC PRECAUTION The DDS VFO kit contains the following components which can be
More informationDigital Clock. Perry Andrews. A Project By. Based on the PIC16F84A Micro controller. Revision C
Digital Clock A Project By Perry Andrews Based on the PIC16F84A Micro controller. Revision C 23 rd January 2011 Contents Contents... 2 Introduction... 2 Design and Development... 3 Construction... 7 Conclusion...
More informationRepairing Mitsubishi WS Blinking green light fuse replacement
Repairing Mitsubishi WS-65511 Blinking green light fuse replacement Repair of the green blinking light by replacing the capacitors on the DM board. This repair can also be performed on the following models:
More informationBASCOM-TV. TV Code Features: ICs supported: BASCOM versions:
BASCOM-TV With this software module you can generate output directly to a TV - via an RGB SCART connection - from BASCOM (AVR), using a just few resistors and a 20 MHz crystal. Write your program with
More informationVGA to PAL and NTSC converter
VGA to PAL and NTSC converter Design and copyright by Tomi Engdahl 1996,1999 NOTE: There are few mistakes on the dawings shown on this page. I have recieved lots of questions related to them and I don't
More information6170 Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free
Instruction Manual Model 2115-202 Upconverter November 2011, Rev. C MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More information7 SEGMENT LED DISPLAY KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SCORE BOARD WITH THIS 7 SEGMENT LED DISPLAY KIT Version 2.0 Which pages of
More informationINSTRUCTIONS FOR USE Pro-Ject Tube Box DS2
INSTRUCTIONS FOR USE Pro-Ject Tube Box DS2 Dear music lover, Thank you for purchasing a tube phono preamplifier from Pro-Ject Audio Systems. In order to achieve maximum performance and reliability you
More information4. Alignment and Adjustments
4. Alignment and Adjustments 4-1 Preadjustment 4-1-1 Factory Mode 1. Do not attempt these adjustments in the Video Mode. 2. The Factory Mode adjustments are necessary when either the EEPROM (IC02) or the
More informationROSS VIDEO LIMITED PAA Programmable Audio Amplifier USER MANUAL PAA-01-MNL Issue 1
ROSS VIDEO LIMITED PAA-7803 Programmable Audio Amplifier USER MANUAL 7803-PAA-01-MNL Issue 1 PAA-7803 Programmable Audio Amplifier User s Manual Ross Part Number: 7803-PAA-01-MNL Document Issue: 1 Printing
More informationService Service Service. B8 Series Chasssis Manual Contents 5. Service Modes, Error Codes and Faultfinding 6. Block Diagrams and Testpoints
Color Television Service Service Service Chassis B8 Series Chasssis Manual 7562 Contents 5. Service Modes, Error Codes and Faultfinding 6. Block Diagrams and Testpoints 7. Electrical Diagrams and PWB's
More informationInstruction Manual Model # Block Upconverter
Instruction Manual Model 2115-278# Block Upconverter August 2018, Rev. A MODEL 2115 UPCONVERTER CROSS TECHNOLOGIES INC. EXT 10MHZ ALARM POWER Data, drawings, and other material contained herein are proprietary
More informationSPECIFICATION. DVB-T / Worldwide NIM Tuner
1.Feature * DVB-T demodulator for COFDM with excellent multipath performance, meeting: * DVB-T Digital Television Standard ETS 300744 * Nordig-Unified v1.0.3 Receiver Specification 2.Applications * Digital
More informationProjection Television
S Training Manual Projection Television Circuit Description and Troubleshooting Course: TVP-08 Course Description and Troubleshooting: RA-4 Chassis Prepared by: National Training Department Sony Service
More informationWS2812B Intelligent control LED integrated light source
Features and Benefits The control circuit and the LED share the only power source. Control circuit and RGB chip are integrated in a package of 5050 components, to form a complete addressable pixel. Built-in
More informationIOCard Displays II Manual. Date:08/03/17 Rev.:2.3
Date:08/03/17 Rev.:2.3 Index: IOCARD DISPLAYS II MANUAL... 1 INDEX:... 2 INTRODUCTION:... 3 DISPLAYS II:... 3 Components and outline:... 3 Connector's description:... 4 INPUTS:... 4 Displays direct to
More informationSN-Class Nixie Clock Kits
Assembly Instructions And User Guide SN-Class Nixie Clock Kits - 1 - REVISION HISTORY Issue Date Reason for Issue Number 1 20 November 2017 New document - 2 - 1. INTRODUCTION 1.1 About the How can the
More informationOBSOLETE HMC215LP4 / 215LP4E. GaAs MMIC MIXER w/ INTEGRATED LO AMPLIFIER, GHz. Typical Applications. Features. Functional Diagram
v1.111 LO AMPLIFIER, 1.7-4. GHz Typical Applications The HMC215LP4 / HMC215LP4E is ideal for Wireless Infrastructure Applications: PCS / 3G Infrastructure Base Stations & Repeaters WiMAX & WiBro ISM &
More informationNixie Clock Type Frank 3'
Assembly Instructions And User Guide Nixie Clock Type Frank 3' - 1 - REVISION HISTORY Issue Number Date Reason for Issue 4 16 December 2016 New diode for D2 3 12 November 2012 Improved first clock test
More informationLP-PAN Preamp Kit Assembly Manual
LP-PAN Preamp Kit Assembly Manual December 2010 TelePost Incorporated Rev. A9 1 Table of Contents Introduction... 2 Specifications... 3 Parts List... 4 Assembly... 5 Checkout / Schematic... 9 Introduction
More informationTimer Modules. MEU11 24 Hour Module, MEU17 7 Day Module (Without Housing)
Timer Modules MEU11 24 Hour Module, MEU17 7 Day Module (Without Housing) EMU11 24 Hour Module, EMU17 7 Day Module (With Housing Giving panel mounting facility) Installation & Operating Instructions 1 1.
More informationAustralian Technical Production Services
Australian Technical Production Services Dual Rail Crowbar Copyright notice. These notes, the design, schematics and diagrams are Copyright Richard Freeman, 2015 While I am happy for the notes to be printed
More informationScale Track System. 21 Century y Signal System 2-Rail Manual
Scale Track System st 21 Century y Signal System 2-Rail Manual TABLE OF CONTENTS Introduction...2-3 Road Signal Board Diagram and Definitions...4-6 Tips for Handling the Circuit Board...6 2-Rail Detector
More informationA Huf Puf VFO stabilizer for the YAESU FT-707
A Huf Puf VFO stabilizer for the YAESU FT-707 Bruno Beckers ON6AB Page 1 The Yaesu FT707 is a good object to add a Huff Puff VFO stabilizer developed by the late Klaas Spaargaren PA0KSB. The version of
More informationNixie Clock Kit V1.08 Assembly and Operation
Nixie Clock Kit V1.08 Assembly and Operation Hardware Revision 14.05.2005 Software Version 6.0 Revision 19.04.2006 This document is copyrighted. No parts of this documentation may be used commercially.
More informationASSEMBLING. the. ECEbot. Printed Circuit Board: Part Three. Due Date. The Part Three assembly steps must be completed prior to:
ASSEMBLING the ECEbot Printed Circuit Board: Part Three Due Date The Part Three assembly steps must be completed prior to: Prepared by R.C. Maher September 2008 Copyright 2008 Department of Electrical
More informationET BLU MIX RX-Condo-3
ET BLU MIX RX-Condo-3 Three channel, 999 user, enhanced rolling code receiver. Ver: 2016.10.001 Product identification: Dark blue base with light blue top casing. White and orange antenna. 3 digit 7 segment
More informationBuilding the BX24-AHT
Building the BX24-AHT file:///f /LASER/build-it.htm (1 of 8) [03/04/2002 5:21:52 PM] file:///f /LASER/build-it.htm (2 of 8) [03/04/2002 5:21:52 PM] Tips & Tricks Use a 25W or smaller soldering iron with
More informationuresearch GRAVITECH.US GRAVITECH GROUP Copyright 2007 MicroResearch GRAVITECH GROUP
GRAVITECH.US uresearch GRAVITECH GROUP Description The I2C-7SEG board is a 5-pin CMOS device that provides 4-digit of 7-segment display using I 2 C bus. There are no external components required. Only
More informationDEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide
DEM 9ULNACK 3.4 GHz. PHEMT LNA amplifier complete kit assembly guide SPECIFICATIONS Noise Figure: < 0.8 db Gain: > 15 db Frequency Range: 3400-3500 MHz Input Voltage: 7-16 VDC Description: The 9ULNACK
More informationI R T Electronics Pty Ltd A.B.N. 35 000 832 575 26 Hotham Parade, ARTARMON N.S.W. 2064 AUSTRALIA National: Phone: (02) 9439 3744 Fax: (02) 9439 7439 International: +61 2 9439 3744 +61 2 9439 7439 Email:
More informationDigital Delay / Pulse Generator DG535 Digital delay and pulse generator (4-channel)
Digital Delay / Pulse Generator Digital delay and pulse generator (4-channel) Digital Delay/Pulse Generator Four independent delay channels Two fully defined pulse channels 5 ps delay resolution 50 ps
More informationMACH3 LaserAce Installation Manual Revision 1. MACH3 LaserAce Installation Manual
WWW.LASERARCADE.COM MACH3 LaserAce Installation Manual Revision 1 MACH3 LaserAce Installation Manual Table of Contents Introduction...1 Parts supplied with MACH3 FNI...1 Why the MACH3 FNI is required...2
More information5. Service Modes, Error Codes, and Fault Finding
Service Modes, Error Codes, and Fault Finding LC4.2E AA 5. EN 11 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: 1. Test Points 2. Service Modes 3. Problems and Solving Tips (related
More informationCOMTECH TECHNOLOGY CO., LTD. MTAS-F SPECIFICATION
1.Feature DVB-T demodulator for COFDM with excellent multipath performance, meeting: * DVB-T Digital Television Standard ETS 300744 * Nordig-Unified v1.0.3 Receiver Specification * DTG performance requirements
More information